Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Generators”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

A dynamic pressure generator for checking complete pressure sensing systems installed on an airplane

A portable dynamic pressure generator, how it operates, and a test setup on an airplane are described. The generator is capable of providing a sinusoidal pressure having a peak-to-peak amplitude of 3.5 N/sq cm (5 psi) at frequencies ranging from 100 hertz to 200 hertz. A typical power spectral density plot of data from actual dynamic pressure fluctuation tests within the air inlet of the YF-12 airplane is presented.

Demarco, D. M.↗
NASA NTRS1974

Development and planning and design of equipment pumping generator of semiconductor lasers

The schematic of a multidimensional current pulse generator is studied. A MTKh-90 cold cathode thyratron is used as the current commutator. In the autooscillation mode on a frequency of 380 hertz the generator creates a current to 100 amps per pulse in a control resistance of 1 ohm. The pulse duration is regulated within the limits from 0.1 to 3.0 microseconds.

Popkov, A. V.↗
NASA NTRS1973

Noise generation by ducted combustion systems

Analysis of the interaction between a zone of nonsteady combustion and its confining duct shows that resonant type oscillations occur with resulting noise intensities far greater than from corresponding unconfined flame zones. The blading action on the flow through the compressor and turbine of an engine generates discrete frequency noise which, it is found, is enhanced by the response of the combustion zone in between. Ducted combustor experiments verify the predicted resonant type noise, the amplitude and frequency of which are strongly influenced by the duct dimensions and end impedance. A convergent exit nozzle results in stronger internal resonant noise oscillations but also generates a higher jet velocity, with the attendant jet noise which exceeds noise from inside the duct at jet Mach numbers near unity.-

Chiu, H. H.↗
NASA NTRS1974

Efficient generation of statistically good pseudonoise by linearly interconnected shift registers

A number of efficient new algorithms for generating digital pseudonoise are presented. The algorithms are efficient because a large number of new pseudorandom bits are generated at each iteration of a computer implementation or at each clock pulse of a hardware implementation. The maximal-length shift register sequences obtained have good randomness properties. Some of the properties of p-n sequences are reviewed and the results of an extensive statistical evaluation of the pseudonoise are presented.

Hurd, W. J.↗
NASA NTRS1974

Generation of Alfven waves in the magnetosphere by parametric interaction between whistlers

A theory is developed for the generation of Alfven waves by the mixing of whistler waves. Calculations are carried out for interaction in the magnetosphere where the whistlers fall in the VLF frequency range and the Alfven wave falls in the ULF(1-5 Hz) range. Typical amplitudes of 2-5 milligammas for the Alfven wave are calculated, and it is shown that these values might be increased by one order of magnitude through suitable variation of the experimental parameters. The study thereby develops a possible explanation for naturally occurring Pc 1 micropulsations and demonstrates the feasibility of artificial generation of such micropulsations by ground-launched whistlers.

Harker, K. J.↗
NASA NTRS1974

A comparative evaluation of three types of acoustic noise generators

Assessment of the operation and performance characteristics of three acoustic noise generators (a siren, an electropneumatic modulator, and an electrohydraulic modulator) when used in conjunction with a progressive wave tube. Particularly, the spectrum shaping capabilities and efficiencies of the three generators are compared.

Cook, L. L., Jr.↗
NASA NTRS1974

Automatic numerical generation of body-fitted curvilinear coordinate system for field containing any number of arbitrary two-dimensional bodies

A method for automatic numerical generation of a general curvilinear coordinate system with coordinate lines coincident with all boundaries of a general multi-connected region containing any number of arbitrarily shaped bodies is presented. With this procedure the numerical solution of a partial differential system may be done on a fixed rectangular field with a square mesh with no interpolation required regardless of the shape of the physical boundaries, regardless of the spacing of the curvilinear coordinate lines in the physical field, and regardless of the movement of the coordinate system. Numerical solutions for the lifting and nonlifting potential flow about Joukowski and Karman-Trefftz airfoils using this coordinate system generation show excellent comparison with the analytic solutions. The application to fields with multiple bodies is illustrated by a potential flow solution for multiple airfoils.

Thompson, J. F.↗
NASA NTRS1974

Wind tunnel flow generation section

A flow generation section for a wind tunnel test facility is described which provides a uniform flow for the wind tunnel test section over a range of different flow velocities. The throat of the flow generation section includes a pair of opposed boundary walls which are porous to the flowing medium in order to provide an increase of velocity by expansion. A plenum chamber is associated with the exterior side of each of such porous walls to separate the same from ambient pressure. A suction manifold is connected by suction lines with each one of the chambers. Valves are positioned in each of the lines to enable the suction manifold to be independently varied.

Sorensen, N. E.↗
NASA NTRS1974

Gust Generator for a Supersonic Wind Tunnel

The effectiveness was investigated of a flat plate gust generator that was located in the nozzle throat of the Lewis 10- by 10-foot supersonic wind tunnel. Gust plates were tested at nozzle wall Mach numbers of 3.1, 2.4, and 2.0. Test results show that the flat plate concept may be used as a gust generator for a wind tunnel; however, more extensive investigation is required to completely define its capabilities and limitations. For the single transient data point recorded, a gust amplitude (decrement) of 0.15 in Mach number was obtained. Analysis of these transient data indicates a response with a corner frequency of at least 8 hertz.

Sanders, Bobby W.↗
NASA NTRS1974

Spacecraft nitrogen generation

Two spacecraft nitrogen (N2) generation systems based on the catalytic dissociation of hydrazine (N2H4) were evaluated. In the first system, liquid N2H4 is catalytically dissociated to yield an N2 and hydrogen (H2) gas mixture. Separation of the N2/H2 gas mixture to yield N2 and a supply of H2 is accomplished using a polymer-electrochemical N2/H2 separator. In the second system, the N2/H2 gas mixture is separated in a two-stage palladium/silver (Pd/Ag) N2/H2 separator. The program culminated in the successful design, fabrication, and testing of a N2H4 catalytic dissociator, a polymer-electrochemical N2/H2 separator, and a two-stage Pd/Ag N2/H2 separator. The hardware developed was sized for an N2 delivery rate of 6.81 kg/d (15lb/day). Experimental results demonstrated that both spacecraft N2 generation systems are capable of producing 6.81 kg/d (15lb/day) of 99.9% pure N2 at a pressure greater than or equal to 1035 kN/m(2) (150 psia).

Marshall, R. D.↗
NASA NTRS1975

Digital computer programs for generating oblique orthographic projections and contour plots

User and programer documentation is presented for two programs for automatic plotting of digital data. One of the programs generates oblique orthographic projections of three-dimensional numerical models and the other program generates contour plots of data distributed in an arbitrary planar region. A general description of the computational algorithms, user instructions, and complete listings of the programs is given. Several plots are included to illustrate various program options, and a single example is described to facilitate learning the use of the programs.

Giles, G. L.↗
NASA NTRS1975

Investigation B: Laminar confined coaxial entrance flow with heat generation

The results of a parametric study on the entrance flow region in a gas core nuclear reactor are presented. The physical system is modeled as laminar confined, coaxial flow with heat generation in the inner fluid. The governing equations include the boundary layer approximations and the assumptions of only radial radiative transport of energy represented as an energy diffusion term. The Von Mises transformation and a zeta transformation are used to transform the equations into nonlinear nonhomogeneous convective-diffusion equations. A unique combination of forward and backward difference equations which yields accurate results at moderate computational times, is used in the numerical method. Results show that the rapidly accelerating, heat generating inner stream actually shrinks in radius as it expands axially.

Bobba, G. K. M.↗
NASA NTRS1975

Comparison of measured and calculated aircraft lift generated pressures

Lift generated pressures produced by large, heavy aircraft at low altitudes were investigated due to concern over their possible effects on ground objects. Aircraft lift generated pressures were calculated using elementary airfoil theory, and these values were compared with ground level measurements made during an overflight program. The predicted and the measured values were in relatively good agreement. Due to lack of experimental investigations of this phenomenon, opportunity was taken during an overflight program to use a specially instrumented test range to measure the ground pressures produced for a range of aircraft weights and distances.

Findley, D. S.↗
NASA NTRS1975

The 100 kW experimental wind turbine generator project

The Energy Research and Development Administration and the NASA Lewis Research Center engaged jointly in a Wind Energy Program which included the design and erection of a 100 kW wind turbine generator. This test machine consists of a rotor turbine, transmission, shaft, alternator, and tower. The rotor, measuring 125 feet in diameter and consisting of two variable pitch blades, operates at 40 rpm and generates 100 kW of electrical power at a wind velocity of 18 mph. The entire assembly is placed on top of a tower 100 feet above ground level. The machine was scheduled to be ready for operation in August, 1975.

Puthoff, R. L.↗
NASA NTRS1975

Monopropellant engine investigation for space shuttle reaction control. Volume 2: Design, fabrication, and demonstration test of a catalytic gas generator for the space shuttle APU

The capability of a catalytic gas generator to meet the requirement specified for the space shuttle APU is established. A full-scale gas generator, designed to operate at a chamber pressure of 750 psia and a flow rate of 0.36 lbm/sec, was fabricated and subjected to three separate life test series. The nickel foam metal used for catalyst retention was investigated. Inspection of the foam metal following the first life test revealed significant degradation. Consequently an investigation was conducted to determine the mechanism of degradation and to provide an improved foam metal.

Source record↗