Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Floating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Determination of Ice Characteristics for Marine Hydroengineering Structures

Problems and potential approaches to determining ice characteristics for sea hydroengineering structures design are considered. A system for numerical modeling of ice dynamics is presented. The system may be used to define ice characteristics on approaches to structures with due regard for local hydrometeorological conditions and ice loads on structures. System application examples are presented for determining computational scenarios for ice loads at structures of the Pevek floating nuclear power plant (FNPP), as well as for the breakwater pier under reconstruction in Vanino. A scenario approach is used to determined ice loads.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Signature of Ferromagnetic Phase at Low Temperature in Low-Doped La{sub 0.88}Ca{sub 0.12}MnO{sub 3} Single Crystal

The confirmation of ferromagnetism at low temperature in a low-doped manganites system is always debatable. It is for the first time, electrical, magnetic, and thermal properties have been measured for manganites single crystal of La{sub 0.88}Ca{sub 0.12}MnO{sub 3} by using a floating-zone method. The electrical resistivity shows a perceptible change of resistance at a low temperature which can be viewed as a signature of the ferromagnetic phase. The ferromagnetic phase of the investigated La{sub 0.88}Ca{sub 0.12}MnO{sub 3} single crystal with Curie temperature of T{sub C} = 120 K which is in closed agreement with ac-susceptibility measurement. An analysis of the specific heat suggests the transition peak (T{sub P}) coincides with the T{sub C} and attains 1.2 J mol{sup −1} K at 116 K. The magnetoresistance (MR) and temperature coefficient of resistance (TCR) were found to be 69% and 10% respectively, which expands its subtle potential for applications in spintronics and thermistor.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Optimal size of the block in block GMRES on GPUs: computational model and experiments

The block version of GMRES (BGMRES) is most advantageous over the single right hand side (RHS) counterpart when the cost of communication is high while the cost of floating point operations is not. This is the particular case on modern graphics processing units (GPUs), while it is generally not the case on traditional central processing units (CPUs). Here, in this paper, experiments on both GPUs and CPUs are shown that compare the performance of BGMRES against GMRES as the number of RHS increases, with a particular focus on GPU performance. The experiments indicate that there are many cases in which BGMRES is slower than GMRES on CPUs, but faster on GPUs. Furthermore, when varying the number of RHS on the GPU, there is an optimal number of RHS where BGMRES is clearly most advantageous over GMRES. A computational model for the GPU is developed using hardware specific parameters, providing insight towards how the qualitative behavior of BGMRES changes as the number of RHS increase, and this model also helps explain the phenomena observed in the experiments.

97 MATHEMATICS AND COMPUTING↗

Two-Phase Flow Mechanisms Controlling CO2 Intrusion into Shaly Caprock

Abstract Geologic carbon storage in deep saline aquifers has emerged as a promising technique to mitigate climate change. CO 2 is buoyant at the storage conditions and tends to float over the resident brine jeopardizing long-term containment goals. Therefore, the caprock sealing capacity is of great importance and requires detailed assessment. We perform supercritical CO 2 injection experiments on shaly caprock samples (intact caprock and fault zone) under representative subsurface conditions. We numerically simulate the experiments, satisfactorily reproducing the observed evolution trends. Simulation results highlight the dynamics of CO 2 flow through the specimens with implications to CO 2 leakage risk assessment in field practices. The large injection-induced overpressure drives CO 2 in free phase into the caprock specimens. However, the relative permeability increase following the drainage path is insufficient to provoke an effective advancement of the free-phase CO 2 . As a result, the bulk CO 2 front becomes almost immobile. This implies that the caprock sealing capacity is unlikely to be compromised by a rapid capillary breakthrough and the injected CO 2 does not penetrate deep into the caprock. In the long term, the intrinsically slow molecular diffusion appears to dominate the migration of CO 2 dissolved into brine. Nonetheless, the inherently tortuous nature of shaly caprock further holds back the diffusive flow, favoring safe underground storage of CO 2 over geological time scales.

58 GEOSCIENCES↗

Flotation of Metallurgical Grade Silicon and Silicon Metal from Slag by Selective Hydrogen Fluoride-Assisted Flotation

Flotation experiments performed on metallurgical grade silicon have demonstrated that silicon (Si) can be floated in diluted solutions of hydrogen fluoride (HF) and a frother. The recovery was found to depend on HF conditioning time, frother type, and the concentration of both HF and frother. Although Brij 58 produced the highest recoveries of the frothers that was tested, good recoveries were also obtained for Flotanol C07. Chemical analyses showed that the flotation products were purer than the corresponding feed materials, and that most impurity elements were concentrated in the tailings. A case study on cleaning of slag containing 36 pct metallurgical silicon showed promising results concerning the recovery of silicon by flotation.

36 MATERIALS SCIENCE↗

Numerical Simulation of Slag Eye Formation and Slag Entrapment in a Bottom-Blown Argon-Stirred Ladle

A transient mathematical model is developed for simulating the bubble-steel-slag-top gas four-phase flow in a bottom-blown argon-stirred ladle with a 70-ton capacity. The Lagrangian discrete phase model (DPM) is used for describing the moving behavior of bubbles in the steel and slag. To observe the formation process of slag eye, the volume of fluid (VOF) model is used to track the interfaces between three incompressible phases: metal/slag, metal/gas, and slag/gas. The complex multiphase turbulent flow induced by bubble-liquid interactions is solved by a large eddy simulation (LES) model. Slag eye area and slag droplet dispersion are investigated under different gas flow rates. The results show that the movement of bubbles, formation and collapse of slag eye, volatility of steel/slag interface and behavior of slag entrapment can be properly predicted in the current model. When the gas flow rate is 300 L/min, the circulation driven by the bubble plume will stir the entire ladle adequately and form a slag eye of the right size. At the same time, it will not cause strong erosion to the ladle wall, and the fluctuation of the interface is of adequate intensity, which will be helpful for improving the desulfurization efficiency; the slag entrapment behavior can also be decreased. Interestingly, with the motion of liquid steel circulation, the collision and coalescence of dispersed slag droplets occur during the floating process in the vicinity of the wall.

36 MATERIALS SCIENCE↗

Thermodynamic and Structural Study of the Copper-Aluminum System by the Electrochemical Method Using a Copper-Selective Beta″ Alumina Membrane

The liquid phase thermodynamics of mixing of the copper-aluminum binary system are investigated as a function of temperature and composition using the electrochemical potential difference method. A copper-selective beta″ alumina is used as a solid electrolyte, synthesized through ion exchange, sintering from base oxide powders, and the floating zone method of crystal growth. Measured thermodynamics of mixing data were used to inform short-range ordering in copper-aluminum melts through Darken’s factor for excess stability and Bhatia–Thornton structure factors, revealing a strong departure from ideality and pronounced ordering. Mixing properties were used to predict viscosity and self-diffusion coefficients. Features observed in calculated electronic entropy of mixing for copper-aluminum were compared with trends in viscosity, demonstrating the utility of electronic properties of mixing in the description of structure–properties in this liquid binary system.

36 MATERIALS SCIENCE↗

Numerical Simulation of the Three-Phase Flow of a Bubble Interacting with the Steel–Slag Interface During the Secondary Refining Process

Gas stirring is an effective method for the secondary refining process of steel. The microphenomena among the phases of an argon bubble floating in steel and motion across the steel–slag interface were simulated and discussed with a sharp interface tracking method. A water-model experiment was set to validate the numerical model, and the experimental results showed agreement with the numerical model. A critical size for bubbles to pass the interface was found using the model.

36 MATERIALS SCIENCE↗

Numerical Simulation of Metal Melt Flow in a One-Strand Tundish Regarding Active Filtration and Reactive Cleaning

In the paper, two different cleaning strategies for nonmetallic inclusions in steel melts, active filtration and reactive cleaning, are examined in a prototype tundish configuration. In active filtration, nonmetallic inclusions are deposited at the filter surfaces. In reactive cleaning, nonmetallic inclusions stick to the filter surfaces, too. In addition, they are floated by the action of carbon monoxide bubbles, which are generated by reaction between carbon and oxygen in the steel melt. In order to compare the performance of both strategies, numerical simulations of the two-phase flows of steel melt and dispersed nonmetallic inclusions are performed. Turbulence is resolved with implicit large eddy simulation. If necessary, species transports of dissolved carbon in the melt and reaction with oxygen are employed. Cleaning efficiencies are deduced from the simulations which demonstrate that reactive cleaning is much more efficient than active filtration.

36 MATERIALS SCIENCE↗

Spurious Grain Formation at Cross-Sectional Expansion During Directional Solidification: Influence of Thermosolutal Convection

Formation of spurious grains during directional solidification (DS) of Al-7 wt.% Si and Al-19 wt.% Cu alloys through an abrupt increase in cross-sectional area has been examined by experiments and by numerical simulations. Stray grains were observed in the Al-19 wt.% Cu samples and almost none in the Al-7 wt.% Si. The locations of the stray grains correlate well where numerical solutions indicate the solute-rich melt to be flowing up the thermal gradient faster than the isotherm velocity. It is proposed that the spurious grain formation occurred by fragmentation of slender tertiary dendrite arms was enhanced by thermosolutal convection. In Al-7 wt.% Si, the dendrite fragments sink in the surrounding melt and get trapped in the dendritic array growing around them, and therefore they do not grow further. In the Al-19 wt.% Cu alloy, on the other hand, the dendrite fragments float in the surrounding melt and some find conducive thermal conditions for further growth and become stray grains.

36 MATERIALS SCIENCE↗

Simulation at Extreme-Scale: Co-Design Thinking and Practices

The current trend of computer architecture evolving towards exaflop/s is the fast increasing floating point performance (the so-called “free” flops) accompanied by much slowly improving the bandwidth of memory and network. Numerical simulation would undergo the challenge posed by the unbalanced increase in the compute power and the capability of data movement. In this paper, after reviewing the challenges of hardware and software in moving towards exascale computing, we present co-design thinking for selecting, optimizing, and developing a numerical algorithm and a simulation tool to meet the challenge of simulation at extreme scale. Examples are presented to demonstrate the new way of thinking and its effectiveness on the emerging architecture.

Computer Science↗

Joining AA7099 to Ni-Cr-Mo Steel Using Single Pass Friction Stir Dovetailing and AA6061 Butter Layer

A novel single pass friction stir dovetailing (FSD) was developed to join thick plate AA7099 to Ni-Cr-Mo steel in a lap configuration through the use of an AA6061 butter layer. The butter layer approach can be shown to significantly reduce interfacial failures by inhibiting the formation of brittle Fe–Al intermetallic compounds (IMCs) which are typically formed during conventional friction stir welding (FSW) of AA7099 directly to steel. This study evaluates the strength and microstructural evolution of the aluminum/steel joint interface between single pass FSD of AA7099/AA6061(butter)/steel fabricated using three different FSD tool configurations. The butter layer was achieved by placement of a free-floating strip of AA6061 within the dovetail groove that was pre-machined in the steel substrate. Friction stir welding was then used to simultaneously join the thick plate AA7099, the AA6061 strip and the AA7099 in a single weld pass. To optimize the joining process, three different pin geometries (full thread, half smooth/half thread, no thread) were evaluated; it was demonstrated that the half smooth/half thread tool produced the strongest weld joint due to the absence of a Zn rich layer at the Al/steel interface. The efficacy of this unique processing technique was tested using lap shear tensile testing as well as high resolution transmission electron microscopy (TEM). A discussion of the new FSD technique, joint configurations, and process parameters are provided along with joint microstructural analyses and mechanical performance.

Olszta, Matthew J.↗

Compression-based integral curve data reuse framework for flow visualization

Currently, by default, integral curves are repeatedly re-computed in different flow visualization applications, such as FTLE field computation, source-destination queries, etc., leading to unnecessary resource cost. We present a compression-based data reuse framework for integral curves, to greatly reduce their retrieval cost, especially in a resource-limited environment. In our design, a hierarchical and hybrid compression scheme is proposed to balance three objectives, including high compression ratio, controllable error, and low decompression cost. Specifically, we use and combine digitized curve sparse representation, floating-point data compression, and octree space partitioning to adaptively achieve the objectives. Results have shown that our data reuse framework could acquire tens of times acceleration in the resource-limited environment compared to on-the-fly particle tracing, and keep controllable information loss. Moreover, our method could provide fast integral curve retrieval for more complex data, such as unstructured mesh data.

97 MATHEMATICS AND COMPUTING↗

A comparison of efficiency-aware model-predictive control approaches for wave energy devices

In this study, we compare four different formulations of model predictive control that attempt to maximise electrical power generated by a wave energy converter (WEC). Control laws include (1) pure maximisation of mechanical power, (2) maximisation of mechanical power with a control penalty factor, (3) maximisation of electrical power using power conversion efficiency, and (4) maximisation of electrical power using the full electro-mechanical model of a system. For this study, a wave-to-wire model is developed for a floating spherical buoy connected to a permanent magnet synchronous generator. The performance of the controllers, including the mechanical and electrical power outputs, is compared in irregular wave conditions for the unconstrained and force-constrained scenarios. The results demonstrate that the controller designed to maximise mechanical power is not suitable for practical applications and may lead to negative electrical power output due to the non-ideal power take-off efficiency. Moreover, the replacement of the power take-off dynamics by the efficiency coefficient does not guarantee the maximum electrical power production.

16 TIDAL AND WAVE POWER↗

Effect of Heave Plate Hydrodynamic Force Parameterization on a Two-Body Wave Energy Converter

Heave plates are one approach to generating the reaction force necessary to harvest energy from ocean waves. In a Morison equation description of the hydrodynamic force, the components of drag and added mass depend primarily on the heave plate oscillation. These terms may be parameterized in three ways: (1) as a single coefficient invariant across sea state, most accurate at the reference sea state, (2) coefficients dependent on the oscillation amplitude, but invariant in phase, that are most accurate for relatively small amplitude motions, and (3) coefficients dependent on both oscillation amplitude and phase, which are accurate for all oscillation amplitudes. We validate a MATLAB model for a two-body point absorber wave energy converter against field data and a dynamical model constructed in ProteusDS. We then use the MATLAB model to evaluate the effect of these parameterizations on estimates of heave plate motion, tension between the float and heave plate, and wave energy converter electrical power output. We find that power predictions using amplitude-dependent coefficients differ by up to 30% from models using invariant coefficients for regular waves ranging in height from 0.5 to 1.9 m. Amplitude- and phase-dependent coefficients, however, yield less than a 5% change when compared with coefficients dependent on amplitude only. This suggests that amplitude-dependent coefficients can be important for accurate wave energy converter modeling, but the added complexity of phase-dependent coefficients yields little further benefit. We show similar, though less pronounced, trends in maximum tether tension, but note that heave plate motion has only a weak dependence on coefficient fidelity. Finally, we emphasize the importance of using experimentally derived added mass over that calculated from boundary element methods, which can lead to substantial under-prediction of power output and peak tether tension.

dynamical model↗

Benchmark study of the DTU OWC chamber with both two-way and one-way absorption

This paper reports on a benchmark study based on small-scale (1:50) measurements of a single, oscillating water column chamber mounted sideways in a long flume. The geometry of the OWC chamber is extracted from a barge-like, attenuator-type floating concept “KNSwing” with 40 chambers targeted for deployment in the Danish part of the North Sea. In addition to traditional two-way energy extraction we also consider one-way energy extraction with passive venting and compare chamber response, pressures and total absorbed energy between the two methods. A blind study was established for the numerical modeling, with participants applying several implementations of weakly nonlinear potential flow theory and commercial Navier–Stokes solvers (CFD). Both compressible and incompressible models were used for the air phase. Potential flow calculations predict more energy absorption near the chamber resonance for one-way absorption than for two-way absorption, but the opposite is found from the experimental measurements. This outcome is mainly attributed to energy losses in the experimental passive valve system, but this conclusion must be confirmed by better experimental measurements. Modeling the one-way valve in CFD proved to be very challenging and only one team was able to provide results which were generally closer to the experiments. The study illustrates the challenges associated with both numerical and experimental analysis of OWC chambers. Air compressibility effects were not found to be important at this scale, even with the large volume of additional air used for the one-way case.

16 TIDAL AND WAVE POWER↗

A Field Survey of Rare Earth Element Concentrations in Process Streams Produced by Coal Preparation Plants in the Eastern USA

I this work, a field study was undertaken to experimentally measure the concentrations of rare earth elements (REEs) contained in the process streams generated by a group of 20 coal preparation plants located in the eastern USA. For each site, representative samples of clean coal product, coarse refuse, and fine refuse were collected. Each sample was then partitioned into preselected size and density classes by wet screening/sieving and float-sink testing. The resultant products were dried and subjected to laboratory analyses to determine ash contents and rare earth element concentrations including Yttrium and Scandium. A detailed analysis of the database generated by this exercise showed that coal-based products from these preparation plants contained significant quantities of rare earth elements. In particular, the coarse refuse streams currently discarded by the 20 plants examined were found to contain a sufficient tonnage of REEs to satisfy the current domestic demand for these important elements. The data also showed a strong positive correlation between ash content and REE concentration, which suggested that the primary association of REEs in eastern USA bituminous coal sources is likely within fractions containing inorganic impurities. This association was well described using a simple power equation relating ash content and REE concentration. The ratio of heavy-to-light rare earth elements was discovered to be significantly higher in organically rich fractions of clean coal, suggesting that mineral impurities intimately associated with carbonaceous matter have elevated concentrations of heavy rare earth elements. A similar trend was observed for a grouping of rare earth elements (Y, Nd, Eu, Tb, and Dy) that are likely subject to near-term supply shortages. Finally, the database showed that a linear correlation existed between La for many REEs of interest, although there were several notable exceptions for some high-value REEs (Lu, Pr, and Tb).

01 COAL, LIGNITE, AND PEAT↗

Techno-Economic Analysis and Global Warming Potential of a Novel Offshore Macroalgae Biorefinery

The success of a large scale macroalgae-based biorefinery is dependent on the demonstration of favorable system economics and environmental sustainability. This study uses detailed process modeling to quantify the mass and energy flows through the various unit operations required for a novel free-floating macroalgae biorefinery concept. The modular process model served as the foundation for the techno-economic and global warming potential analyses used to quantify the sustainability of the proposed concept. This work includes detailed techno-economic results for a complete macroalgae cultivation and conversion system with multiple hatchery configurations and several emerging technologies. System optimization was achieved through the evaluation of various technology options for each unit operation. Technologies considered include traditional twine and textile substrate hatchery configurations, drone assisted seeding and biomass transport, mechanized line seeding and harvesting, adhesive spore mixtures that simplify seeding operations and improve hatchery energetics, and hydrothermal liquefaction to produce upgradable biocrude. Outputs from the system include renewable diesel (R100), naphtha, biochar, nitrogen and phosphorus fertilizers, and aqueous/solid waste streams. Three different system pathways were explored, yielding a biomass production cost ranging from $210 to $565 per dry metric ton and a minimum fuel selling price from $1.35 to $2.91 per liter of gasoline equivalent. Stochastic manipulation of the process model and sensitivity analyses support these results. The global warming potential analysis shows net greenhouse gas emissions ranging from 14 to 29 gCO2-eq MJ-1, supported by stochastic and sensitivity analyses. The recommendations from this work highlight critical areas for research and development investment such that a sustainable macroalgae cultivation and conversion system can be realized.

NOMAD seaweed cultivation, techno-economic analysi↗