Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FABRICATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Fabrication and thermophysical properties of UO 2 -UB 2 and UO 2 -UB 4 composites sintered via spark plasma sintering

Uranium dioxide (UO 2 ) composites with uranium diboride (UB 2 ) and uranium tetraboride (UB 4 ) have been proposed as advanced fuel candidates due to their high thermal conductivity, high melting point, high fissile density and their ability to incorporate a built-in burnable poison by tailoring the targeted 10 B/ 11 B ratio. As such, it is important to assess the fabrication, and thermal and micromechanical properties of such composites. In this work, UO 2 -UB 2 and UO 2 -UB 4 samples with boride phase fractions of 5, 15 and 30 wt% were fabricated to high densities (above 95 % theoretical density) via spark plasma sintering (SPS). This enabled sintering at relatively low temperatures and short timescales. SPS also aided in maintaining the target phase fractions of the samples as reactions between the constituent phases were suppressed due to the short timescales and reducing environment during sintering. Here, thermal diffusivity measurements from 299 to 1273 K were conducted through laser flash analysis (LFA). The diffusivity increased as a function of boride weight fraction, and UB 2 additions increased the thermal diffusivity of the composites more than UB 4 additions. Assessment of the LFA results indicated in-situ reactions between the UO 2 and boride phases that suppress the thermal diffusivity occur above 800 K for all samples. Oxidation of the boride phase was proposed as the underlying reaction. This was supported by thermodynamic assessments from the literature, as well as microstructural, crystallographic, and nanoindentation characterization performed on these samples.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Microstructural characterization of as-fabricated monolithic plates with boron carbide, aluminum boride, and zirconium boride burnable absorbers

The use of burnable absorbers can be beneficial for nuclear reactors by extending the fuel’s operational cycle, providing additional criticality control, and flattening the power profile. In this work, three burnable absorber materials (boron carbide, aluminum boride, and zirconium boride) embedded in aluminum have been fabricated into foils and clad in AA-6061 for potential use in high performance research reactors. The as-fabricated boron-containing phases were determined using transmission electron microscopy to be AlB2, B4C, and ZrB2. TEM also revealed weak bonding at the B4C-matrix interface. SEM showed a relatively uniform spatial distribution of boron-containing phases for all the candidate materials. Higher porosity was observed in the foil containing ZrB2 in its as-rolled condition. The porosity in the ZrB2 foil was reduced by hot isostatic pressing. The size and shape distributions of the boron-containing phases were analyzed on the criteria of cross-sectional area, perimeter, roundness, circularity, and aspect ratio. A method of converting the 2D burnable absorber dispersoids seen in cross-sectional microscopy images into 3D volumes was derived using both spherical and ellipsoidal geometry models. The difference in calculated burnable absorber dispersoid average volume between the two models ranges from 20% to 100%, which could impact burnable absorber burnout rates due to differences in neutron self-shielding.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2018

Facile and scalable fabrication of polymer-ceramic composite electrolyte with high ceramic loadings

Solid state electrolytes are a promising alternative to flammable liquid electrolytes for high-energy lithium battery applications. In this work polymer-ceramic composite electrolyte membrane with high ceramic loading (greater than 60 vol%) is fabricated using a model polymer electrolyte poly(ethylene oxide) + lithium trifluoromethane sulfonate and a lithium-conducting ceramic powder. The effects of processing methods, choice of plasticizer and varying composition on ionic conductivity of the composite electrolyte are thoroughly investigated. The physical, structural and thermal properties of the composites are exhaustively characterized. We demonstrate that aqueous spray coating followed by hot pressing is a scalable and inexpensive technique to obtain composite membranes that are amazingly dense and uniform. The ionic conductivity of composites fabricated using this protocol is at least one order of magnitude higher than those made by dry milling and solution casting. The introduction of tetraethylene glycol dimethyl ether further increases the ionic conductivity. The composite electrolyte's interfacial compatibility with metallic lithium and good cyclability is verified by constructing lithium symmetrical cells. As a result, a remarkable Li + transference number of 0.79 is discovered for the composite electrolyte.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Ultrarapid crystallization of low-dimensional perovskite with excellent stability for future high-throughput fabrication

We report perovskite solar cells (PSCs) as an emerging photovoltaic technique have achieved exceptional power conversion efficiency (PCE) up to 25.7% after fast development over the past decade. But currently some critical issues are still not well addressed in terms of realizing large-scale fabrication, for example, fast fabrication of high-quality perovskite film with good stability. Here, we demonstrate the use of stable and fast-crystallizing low-dimensional (LD) perovskite thin films as the light absorber with only a 10 s annealing time at 250 °C, delivering a PCE of 18.16%. The crystallization and photoelectric properties of LD perovskite are well illustrated. The reduction in the annealing time will dramatically increase the productivity of PSCs. The PSCs based on rapidly annealed LD perovskite thin films exhibit excellent stability, with only 12% loss of PCE after 1000 h storage at 85 °C and 40-70% relative humidity.

14 SOLAR ENERGY↗
DOE OSTI2015

Fabrication of Au- and Ag–SiO{sub 2} inverse opals having both localized surface plasmon resonance and Bragg diffraction

The inverse opal films of SiO{sub 2} containing metal nanoparticles can have both the localized surface plasmon resonance (LSPR) of metal nanoparticles and the Bragg diffraction of inverse opal crystals of SiO{sub 2}, which are very useful properties for applications, such as tunable photonic structures, catalysts and sensors. However, effective processes for fabrication of these films from colloidal particles have rarely been reported. In our study, two methods for preparation of inverse opal films of SiO{sub 2} with three different crystal sizes and containing gold or silver nanoparticles (NPs) via self-assembly using electrostatic interactions and capillary forces are reported. The Bragg diffraction of inverse opal films of SiO{sub 2} in the presence and absence of the template was measured and predicted on the basis of with UV–vis spectroscopy and scanning electron microscopy. The preparation methods used provided good-quality inverse opal SiO{sub 2} films containing highly dispersed, plasmonic AuNPs or AgNPs and having both Bragg diffractions and LSPRs. - Graphical abstract: For syntheses of SiO{sub 2} inverse opals containing Au/Ag nanoparticles two approaches and three template sizes were employed. Self-assembly of template molecules and metal nanoparticles occurred using electrostatic interactions and capillary forces. Both the Bragg diffraction of the photonic crystal and the localized surface plasmon resonance of Au/Ag nanoparticles were detected. - Highlights: • Fabrication methods of silica inverse opals containing metal nanoparticles studied. • Three template sizes used to produce SiO{sub 2} inverse opals with Au/Ag nanoparticles. • PS templates with Au nanoparticles adsorbed used in formation of inverse opals. • Ag particles infiltrated in inverse opals with capillary and electrostatic forces. • Bragg diffractions of IOs and surface plasmon resonances of nanoparticles observed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2017

Fabrication of Ln-MOFs with color-tunable photoluminescence and sensing for small molecules

Three isomorphic lanthanide metal-organic frameworks (Ln-MOFs) [LnL(H{sub 2}O){sub 2}]·2H{sub 2}O (Ln=Tb for 1, Eu for 2, Gd for 3) have been constructed from flexible organic ligand 4-(2-carboxyphenoxy)benzene-1,3-dioic acid (H{sub 3}L). They exhibit two-dimensional (2D) layered structure with the rhombus windows along the b axis. This network can be described as a shubnikov plane net with Schäfli symbol of (4{sup 3}){sub 2}(4{sup 6}.6{sup 6}.8{sup 3}). Solid state luminescent studies indicate that 1 and 2 show the characteristic red, and green emissions of the corresponding Ln{sup 3+} ions, respectively, while 3 exhibits blue emission arising from the organic ligand. Then by adjusting the relative amounts of different luminescent components into the well-defined host framework, a series of new co-doped Ln-MOF, Tb{sub 1−x}Eu{sub x}L (4) (x refers to the molar ratios of Eu{sup 3+} and Tb{sup 3+}), with tunable luminescence have been fabricated. The luminescent color of 4 can be tuned from green to red due to the energy transfer from the Tb{sup 3+} to Eu{sup 3+} ions by changing the doping concentration of the Eu{sup 3+} ions. In addition, 2 exhibits good stability in different solvents and excellent fluorescence sensing for small molecules, especially for CH{sub 3}CN and nitrobenzene. - Graphical abstract: A series of isomorphic 2D layered Ln-MOFs have been constructed from flexible tricarboxylic ligand, showing tunable luminescence and excellent fluorescence sensing for small molecules, respectively. - Highlights: • Three isomorphic 2D layered Ln-MOFs were constructed by flexible tricarboxylic acid. • A series of Eu{sup 3+}/Tb{sup 3+} doped Ln-MOF 4 were fabricated and showed tunable luminescence. • Ln-MOF 2 exhibited excellent fluorescence sensing for small molecules.

36 MATERIALS SCIENCE↗
DOE OSTI2017

On fabrication procedures of Li-ion conducting garnets

Ceramic oxides exhibiting high lithium-ion mobility at room temperature receive broad attention as candidate electrolytes for lithium batteries. Lithium-stuffed garnets from the Li{sub 7}La{sub 3}Zr{sub 2}O{sub 12} group seem to be especially promising because of their high ionic conductivity at room temperature and their electrochemical stability. In this work, we discuss factors that affect formation of the garnet in its bulk form or in the form of thick and thin films. We demonstrate that zinc oxide can be applied as a sintering aid that facilitate the formation of the highly conducting cubic Li{sub 7}La{sub 3}Zr{sub 2}O{sub 12} garnet phase in a single-step sintering procedure. Based on our experience with the single-step sintering experiments, we successfully fabricated a thick-film membrane consisting of a garnet solid electrolyte using the tape casting technique. In order to reduce the thickness of the electrolyte even further we investigated the fabrication of a thin-film Li{sub 7}La{sub 3}Zr{sub 2}O{sub 12} electrolyte by means of the pulsed laser deposition technique.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2014

Peculiarities of formation of phase composition, porous structure, and catalytic properties of tungsten oxide-based macroporous materials fabricated by sol–gel synthesis

The method of template sol–gel synthesis of tungsten oxide-based macroporous materials using ‘core–shell’ latex particles as colloid templates is described. The chemical composition and structural characteristics of the synthesized macroporous oxide systems have been investigated. The peculiarities of formation of material phase composition and macroporous structure under different template thermal destruction conditions have been revealed. An optimal method of a targeted synthesis of the crystalline tungsten(VI) oxide having a defect-free macroporous structure (average pore size 160 nm) and efficient catalytic properties under organic liquid phase oxidation conditions has been suggested. The prospects of the fabricated material application as catalysts of hydrothermal oxidation of radionuclide organic complexes at radioactive waste decontamination have been demonstrated. - Highlights: • Macroporous tungsten oxides were fabricated via sol–gel process. • The correlation between synthesis conditions and composition was determined. • Influence of synthesis conditions on porous structure has been explained. • The effects of template thermodestruction have been set up. • High potential of such materials for catalysis applications has been shown.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Fabrication and characterization of copper oxide (CuO)–gold (Au)–titania (TiO{sub 2}) and copper oxide (CuO)–gold (Au)–indium tin oxide (ITO) nanowire heterostructures

Nanoscale heterostructures composed of standing copper oxide nanowires decorated with Au nanoparticles and shells of titania and indium tin oxide were fabricated. The fabrication process involved surfactant-free and wet-chemical nucleation of gold nanoparticles on copper oxide nanowires followed by a line-of-sight sputtering of titania or indium tin oxide. The heterostructures were characterized using high resolution electron microscopy, diffraction, and energy dispersive spectroscopy. The interfaces, morphologies, crystallinity, phases, and chemical compositions were analyzed. The process of direct nucleation of gold nanoparticles on copper oxide nanoparticles resulted in low energy interface with aligned lattice for both the components. Coatings of polycrystalline titania or amorphous indium tin oxide were deposited on standing copper oxide nanowire–gold nanoparticle heterostructures. Self-shadowing effect due to standing nanowire heterostructures was observed for line-of-sight sputter deposition of titania or indium tin oxide coatings. Finally, the heterostructures were studied using Raman spectroscopy and ultraviolet–visible spectroscopy, including band gap energy analysis. Tailing in the band gap energy at longer wavelengths (or lower energies) was observed for the nanowire heterostructures. - Highlights: • Heterostructures comprised of CuO nanowires coated with Au nanoparticles. • Au nanoparticles exhibited nearly flat and low energy interface with nanowire. • Heterostructures were further sputter-coated with oxide shell of TiO{sub 2} or ITO. • The process resulted in coating of polycrystalline TiO{sub 2} and amorphous ITO shell.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Fabrication of ultra-fine grained aluminium tubes by RTES technique

Recently, repetitive tube expansion and shrinking have been exploited as a means for producing ultra-fine grained and nano-crystalline microstructures for magnesium alloy tubes. This method includes two different half-cycles and was based on pressing a tubular part through an angular channel die with two shear zones. Since the aluminium alloys are the most widely used materials in industries, in this study, repetitive tube expansion and shrinking as a new severe plastic deformation technique was applied to commercially pure aluminium for fabricating ultra-fine grained aluminium tubes for the first time and the ability of this process in significant grain refinement is determined even after single cycle. Transmission electron microscopy and X-ray diffraction were used to evaluate the microstructure of the repetitive tube expansion and shrinking processed materials and the examinations showed ultra-fine grains with the average grain size of 320 nm after one cycle of repetitive tube expansion and shrinking. The yield strength, ultimate tensile strength increased notably by the factor of 2.17 and 1.27 respectively, after one cycle of repetitive tube expansion and shrinking, whereas the elongation to failure as well as the uniform elongation decreased. Furthermore, micro-hardness distribution through the part's section proposed the hardness increasing to ~ 55 HV from the initial value of ~ 28 HV after one cycle of repetitive tube expansion and shrinking. - Highlights: • RTES was introduced for fabricating the UFGed AA1050 tubes for the first time. • Nano-grained AA1050 tube was obtained by RTES process. • Grain size of ~ 320 nm was obtained after two half-cycles of RTES process. • Yield and ultimate strength increased by the factor of 2.17 and 1.27 respectively. • The microhardness increased to ~ 55 HV from the initial value of ~ 28 HV.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Interfacial characteristics of diamond/aluminum composites with high thermal conductivity fabricated by squeeze-casting method

In this work, aluminum matrix composites reinforced with diamond particles (diamond/aluminum composites) were fabricated by squeeze casting method. The material exhibited a thermal conductivity as high as 613 W / (m · K). The obtained composites were investigated by scanning electron microscope and transmission electron microscope in terms of the (100) and (111) facets of diamond particles. The diamond particles were observed to be homogeneously distributed in the aluminum matrix. The diamond{sub (111)}/Al interface was found to be devoid of reaction products. While at the diamond{sub (100)}/Al interface, large-sized aluminum carbides (Al{sub 4}C{sub 3}) with twin-crystal structure were identified. The interfacial characteristics were believed to be responsible for the excellent thermal conductivity of the material. - Graphical abstract: Display Omitted - Highlights: • Squeeze casting method was introduced to fabricate diamond/Al composite. • Sound interfacial bonding with excellent thermal conductivity was produced. • Diamond{sub (111)}/ aluminum interface was firstly characterized by TEM/HRTEM. • Physical combination was the controlling bonding for diamond{sub (111)}/aluminum. • The growth mechanism of Al{sub 4}C{sub 3} was analyzed by crystallography theory.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Accumulative fold-forging (AFF) as a novel severe plastic deformation process to fabricate a high strength ultra-fine grained layered aluminum alloy structure

Highlights: • A novel SPD process named as AFF was introduced. • AFF process is based on the repetitive forging of folded metal foils. • This new method possesses an exceptional capability for fabrication of UFG layered structures. • An AA8006 aluminum alloy layered material with the UFG structure of 200–300 nm was produced. • An enhanced hardness up to ~ 100% was attained owing to the UFG and layered structures. - Abstract: A novel severe plastic deformation (SPD) process termed accumulative fold forging (AFF) is introduced to fabricate a homogenous ultra-fine grained (UFG) layered metal structure by repetitive folding and forging aluminum alloy foil. The present work studies AFF applied to thin foils of AA8006 Al-Fe-Mn aluminum alloy after 26 folding steps to produce a UFG structure containing 67,108,864 layers across a 2 mm thickness. The structure of the layers and grain refinement are studied using X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM) and scanning-transmission electron microscopy (STEM) analysis. The results indicate a well-bonded inter-layer structure with an average grain size of about 200 nm parallel and 250 nm perpendicular to the forging direction, while dislocation density increased to ~ 7.2 × 10{sup 15} m{sup − 2} following AFF. The mechanical strength of the aluminum foil is evaluated in the terms of indentation hardness testing before and after AFF process. The processed UFGed layered material exhibited an average hardness value of ~ 61.5 Vickers as compared to the initial value of ~ 30.4 Vickers for the annealed foil alloy, which indicates an improvement of ~ 100% due to the contributions of grain refinement, work hardening and interfacial strengthening of the bonded layers.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Modification of microstructure and properties of Ti-47Al-2Cr-4Nb-0.3W alloys fabricated by SPS with trace multilayer graphene addition

Highlights: • The TiAl alloys with different content addition of multilayer graphene were fabricated. • When the graphene content is 0.8 at.%, the mean grain size decreases to 8.2 μm. • The bending and fracture strength increase to 1000 MPa and 2347 MPa, respectively. • The friction coefficient decreased from 0.6 to 0.4, with a decrease by 1/3. - Abstract: In this paper, Ti-47Al-2Cr-4Nb-0.3W alloys with trace multilayer graphene addition were fabricated by spark plasma sintering to enhance both mechanical properties and tribological property simultaneously. With the addition of multilayer graphene, bending strength, compressive strength and tribological property of TiAl alloys are all improved. When graphene content increases from zero to 0.8 at.%, the mean grain size decreases from 14.8 ± 1.4 μm to 8.2 ± 0.8 μm. The bending strength reaches almost 1000 MPa and the fracture strength increases to 2347 ± 12 MPa, an increase of 15% compared with TiAl alloy. The friction coefficient also decreases from about 0.6 to 0.4, a decrease by 1/3 compared with TiAl alloy. The reasons for the improved mechanical properties and tribological property are the in-situ reaction plate-shape Ti{sub 2}AlC phase, fine needle-like Ti{sub 3}AlC phase as well as fine and homogeneous microstructure. The wear mechanism changes from abrasive wear to abrasive wear plus adhesive wear with the increased graphene content.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2018

Evaluation of the microstructure and mechanical properties of WC particle reinforced aluminum matrix composites fabricated by friction stir processing

Highlights: • FSP was used for the preparation of aluminum matrix composites reinforced with WC particle. • WC particles were uniformly distributed in the composite. • WC particles refined the grains of aluminum matrix. • WC particles enhanced the hardness and tensile strength, but decreased the ductility. - Abstract: Tungsten carbide (WC) is an attractive reinforcing material for aluminum and its alloys. However, it is technically challenging to fabricate WC particle reinforced aluminum matrix composites (AMCs) with homogeneous distribution of WC particles by liquid state processing techniques because of large density gradient. The present work aim to produce WC particle reinforced aluminum matrix composites (AMCs) through friction stir processing (FSP) and analyze the effect of its volume fraction on the microstructural features and the mechanical behavior of the developed AMCs. Microstructural evaluation was conducted on the cross-sections of the samples by optical microscopy (OM), scanning electron microscopy (SEM) and electron backscattered diffraction (EBSD). Microhardness testing was conducted across the cross-sections of FSPed samples to obtain hardness profiles and tensile test was conducted on as-received Al and FSPed samples. The fabricated AMCs exhibited the homogeneous distribution of WC particle with no obvious particle clustering in the stir zone, irrespective of position and WC particle volume fraction. Excellent WC/Al interfacial bonding was obtained in all FSPed AMCs with obviously refined grains. The average size of WC particles after FSP was slightly reduced with the increased volume fraction. It was also found that increasing the volume fraction of WC particles favored the grain refinement, improved the hardness and strength, but decreased the ductility. This improvement in the hardness and strength was attributed to the grain refinement strengthening and homogeneous distribution of WC particles. The decreased ductility resulted from the introduction of more WC particles. Increasing the volume fraction of WC particles caused the nature of fracture to move towards brittle nature.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Densification, microstructure and properties of TiB2 ceramics fabricated by spark plasma sintering

Highlights: • Nearly full densification of in-house processed TiB{sub 2} ceramic powders at 1500 °C. • Microstructures revealing the size and shape of TiB{sub 2} grains after SPS. • The effect of sub-micron particles on the densification during SPS. • The effect of sintering pressure on the microstructure. • Microhardness and nano-indentation measurements along with oxidation studies. - Abstract: This study reports the fabrication of high-density TiB{sub 2} ceramics at reduced temperatures (1500 °C) by using field assisted sintering technology/spark plasma sintering (FAST/SPS) technique. In-house processed TiB{sub 2} powders with high purity were employed as starting materials. The effects of SPS conditions on the sintering behavior and microstructure of TiB{sub 2} were investigated. Sub-micron character of TiB{sub 2} particles has a strong influence on the densification during SPS. Microstructural analyses revealed that the high pressure affected both the grain size and the shape of TiB{sub 2} crystallites. Elongated grains with average size of 6 μm were perceived in TiB{sub 2} sample fabricated by SPS at 1500 °C under 60 MPa pressure with a relative density of 96.7%. The microhardness and elastic modulus were measured as 27.4 GPa and 685.2 GPa, respectively. This sample revealed an improved oxidation resistance due to the formation of a thin oxidation layer on the surface when heated up to 1200 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Influence of fabrication on microstructure and heat affected zone width in weldments of nuclear reactor pressure vessel steel

Advanced manufacturing routes such as electron beam welding and powder metallurgy with hot isostatic pressing are increasingly used across energy and aerospace industries, where the reliable prediction of weld behavior and heat affected zone (HAZ) evolution is critical. This study examines how fabrication routes and post-weld heat treatments influence phase distribution, crystallite size, microstrain, and dislocation density in nuclear reactor pressure vessel steels using synchrotron X-ray diffraction (SXRD). Retained austenite occurs only in samples that did not undergo austenitization, whereas an austenitizing heat treatment fully eliminates retained austenite and produces a more uniform microstructure across the weldment in terms of phase fraction, dislocation density, and microstrain. The Rosenthal solution underestimates the HAZ width for powder metallurgy samples. A newly proposed modified Rosenthal solution, reducing density by accounting for porosity, matches the SXRD-measured HAZ width with a 0.65% error. Structure–property correlations reveal that dislocation density correlates strongly with nanohardness in homogenous microstructures, while in heterogenous weldments nanohardness is further influenced by the presence of dissimilar phase boundaries. These findings provide new insight into the thermal and microstructural response of powder metallurgy fabricated steels and offer a framework for optimizing welding procedures and heat treatments in advanced manufacturing applications.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2013

Fabrication of platinum nanoparticles in aqueous solution and solid phase using amphiphilic PB-b-PEO copolymer nanoreactors

Graphical abstract: TEM image of Pt nanoparticles produced by reducing by NaBH{sub 4} within PB-b-PEO micelles in aqueous media (scale bar 1 nm). - Highlights: • Pt nanoparticles were synthesized within amphiphilic diblock copolymer micelles. • The effects of reducing agents and precursor dose on Pt np size were investigated. • The effect on fabrication of Pt np by reducing in aqueous and solid phases was compared. • The size of nanoparticles was about 1.4 nm for all doses and reducing agents types. - Abstract: Fabrication of Pt nanoparticles using an amphiphilic copolymer template in aqueous solution was achieved via polybutadiene-block-polyethyleneoxide copolymer micelles, which acted as nanoreactors. In addition, Pt nanoparticles were synthesized using hydrogen gas as the reducing agent in solid state for the first time to compare against solution synthesis. The influences of loaded precursor salt amount to micelles and the type of reducing agent on the size of nanoparticles were investigated through transmission electron microscopy. It was found that increasing the ratio of precursor salt to copolymer and using different type of reducing agent, even in solid phase reduction, did not affect the nanoparticle size. The average size of Pt nanoparticles was estimated to be 1.4 ± 0.1 nm. The reason for getting same sized nanoparticles was discussed in the light of nucleation, growth process, stabilization and diffusion of nanoparticles within micelles.

36 MATERIALS SCIENCE↗
DOE OSTI2013

Fabrication and characterization of a nanoporous NiO film with high specific energy and power via an electrochemical dealloying approach

Graphical abstract: The maximum values were 170 Wh kg{sup −1} and 27.5 kW kg{sup −1} for specific energy and power at the potential window of 1.1 V, respectively. As so far as we know, the values of specific energy and power were both the highest than that reported in literatures. - Highlights: • We developed a convenient approach to fabricate the three-dimensional nanoporous NiO film. • The nanoporous films contain irregular 3D interconnected nanosheets structure with open channels. • The film as supercapacitor electrode showed excellent specific capacitance values. • It is noticed that the nanoporous film exhibited high specific energy and high specific power. • The electrochemical electrode presented excellent cycling performance and low retention. - Abstract: A three-dimensional (3D) nanoporous NiO film was fabricated via a two-step process using an electrochemical route. This process included electrodeposition of the Ni/Zn alloy film and electrochemical dealloying using a direct-current power source. The scanning electron microscopy images suggest that the film has an irregular 3D interconnected nanosheet structure with open channels. The adsorption–desorption isotherms indicate that the as-prepared NiO film had a high specific surface area of 198 m g{sup −1} and a narrow pore size distribution, with two peaks at 2.7 and 5.1 nm. The specific capacitance of the sample reached 1670 F g{sup −1} at a discharge current density of 1 A g{sup −1}. In addition, the as-prepared nanoporous film exhibited high performance during a long-term cycling test. The maximum values for the specific energy and specific power at the 1.1 V potential window were 170 and 27.5 kW kg{sup −1}, respectively.

36 MATERIALS SCIENCE↗