Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EXIT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Design and experimental performance of short curved wall diffusers with axial symmetry utilizing slot suction

The feasibility of designing short curved wall axially symmetrical subsonic diffusers utilizing suction through slots in the diffuser walls to prevent flow separation was investigated. A potential flow analysis was made, and a digital computer program was written for determining the diffuser wall contour for prescribed boundary conditions. The flow field included branch flow so that the suction slot geometry could be a part of the diffuser design. One bell shaped diffuser and three annular diffusers with area ratios of either 2.5:1 or 3:1 were designed, fabricated, and tested. Minimum suction requirements of metastable operation ranged from 6.3 percent to 12 percent when operating with inlet air velocities in the 1000 to 250 ft/sec (30 to 76 m/sec) range. For stable operation suction rates from 10 percent to 22 percent were required. In all cases the diffuser effectiveness was above 95 percent based on the conventional definition, and from 81 percent to 94 percent when the suction loss was accounted for. The exit velocity profiles were virtually flat with no more than + or - 9% variation over 95 percent of the exit area when operated with sufficient suction to prevent flow separation.

Yang, T.↗

Analysis of noise produced by an orderly structure of turbulent jets

The orderly structure which has been observed recently by numerous researchers within the transition region of subsonic turbulent jets is analyzed to reveal its noise-producing potential. For a circular jet, this structure is molded as a train of toroidal vortex rings which are formed near the jet exit and propagate downstream. The noise produced by the model is evaluated from a reformulation of Lighthill's expression for the far-field acoustic density, which emphasizes the importance of the vorticity within the turbulent flow field. It is shown that the noise production occurs mainly close to the jet exit and depends primarily upon temporal changes in the toroidal radii. The analysis suggests that the process of formation of this regular structure may also be an important contribution of the high-frequency jet noise. These results may be helpful in the understanding of jet-noise generation and in new approaches to jet-noise suppression.

Hardin, J. C.↗

Interferometric rotation sensor

An interferometric rotation sensor and control system is provided which includes a compound prism interferometer and an associated direction control system. Light entering the interferometer is split into two paths with the light in the respective paths being reflected an unequal number of times, and then being recombined at an exit aperture in phase differing relationships. Incoming light is deviated from the optical axis of the device by an angle, alpha. The angle causes a similar displacement of the two component images at the exit aperture which results in a fringe pattern. Fringe numbers are directly related to angle alpha. Various control systems of the interferometer are given.

Walsh, T. M.↗

Primary electron spectrometer, 18:63 UE: Electrostatic analyzer description and energy spectrum determination

The primary electron spectrometer used to detect auroral electrons on sounding rocket 18:63 UE is described. The spectrometer used exponentially decaying positive and negative voltages applied to spherical deflection plates for energy analysis. A method for determining the analyzer response which does not require the assumptions that the ratio of plate separation to mean radius, the entrance or the exit apertures are small is described. By comparison with experiment it is shown that the effect of neither entrance nor exit collimation can be ignored. The experimental and calculated values of the limiting orbits agree well. A non-iterative technique of unfolding the electron differential energy spectrum is described. This method does not require the usual assumption of a flat or histogram-type energy spectrum. The unfolded spectra using both this technique and one which assumes a flat spectrum are compared to actual input spectra. This technique is especially useful in analyzing peaked auroral electron energy spectra.

Pongratz, M. B.↗

Power Plant Systems Analysis

Three basic thermodynamic cycles of advanced nuclear MHD power plant systems are studied. The effect of reactor exit temperature and space radiator temperature on the overall thermal efficiency of a regenerative turbine compressor power plant system is shown. The effect of MHD pressure ratio on plant efficiency is also described, along with the dependence of MHD power output, compressor power requirement, turbine power output, mass flow rate of H2, and overall plant efficiency on the reactor exit temperature for a specific configuration.

Williams, J. R.↗

Performance of an annual combustor designed for a low-cost turbojet engine

Performance tests were conducted on a combustor designed for use in a low-cost turbojet engine. Low-cost features included the use of very inexpensive simplex fuel nozzles and combustor liners of perforated sheet material. Combustion efficiencies at the altitude-cruise and sea-level design points were approximately 94 and 96 percent, respectively. The combustor isothermal total-pressure loss was 8.8 percent at the altitude-cruise-condition diffuser-inlet Mach number of 0.335. The combustor-exit temperature pattern factor was less than 0.3 at the altitude-cruise, sea-level-cruise, and sea-level-static design conditions. The combustor-exit average radial temperature profiles at all conditions were in very good agreement with the design profile. The intense mixing required because of the very high combustor heat-release rate had an adverse effect on ignition capability at altitude windmilling design conditions.

Fear, J. S.↗

Molecular flux measurements in the back flow region of a nozzle plume

A series of tests were conducted to measure the mass flux in the far field of a nozzle plume in a high vacuum with emphasis on the back flow region. The measurements presented provided fairly accurate data for off-axis angles as large as 140 deg (i.e., in the back flow region). This region, since it is well behind the exit plane, is of paticular interest to those concerned with instrument contamination. Usually sensitive spacecraft surfaces are located in the region affected by the back flow. Parameters such as expansion ratio, throat diameter, nozzle lip shape, and plenum (chamber) pressure were varied, carbon dioxide and nitrogen gases were flowed and mass flux measurements were taken using quartz crystal microbalances in as many as nine different locations relative to the tests nozzle. Several conclusions with respect to the effect of nozzle and gas parameters on the amount of back flow mass flux are offered, and it was demonstrated that gaseous mass fluxes, which are not predictable by present theories, are encountered in the region behind the nozzle exit plane. This knowledge is significant if materials incompatible with the gaseous exhaust products are used in this region.

Chirivella, J. E.↗

Annular truncated plug nozzle flowfield and base pressure characteristics.

The flowfield and base pressure characteristics of an internal-external expansion, truncated plug nozzle are described over the pressure ratio range from 'open' wake to 'closed' wake conditions. The effect of plug length on these characteristics, including the process of wake 'closure' is also presented. An existing method for calculating the flowfield and base pressure, for 'closed' wake operation, is modified to include the internal shock wave generated near the shroud exit. The supersonic portion of the flow is calculated using rotational axisymmetric method of characteristics. The technique of Hartree is employed so that the downstream characteristic point locations can be chosen to fit the developing flowfield. An overexpansion technique is used to detect the internal shock wave in the vicinity of the shroud exit so that its effect on the plug base pressure could be determined. Good agreement between the analytical results and experimental data is obtained for 'closed' wake operations.

Sule, W. P.↗

Noise characteristics of combustion augmented high speed jets.

Noise generation by a subsonic flow discharging from a combustion chamber is examined with regard to the relative importance of combustion as a source of noise in such a flow system. Measurements of pressure fluctuations inside the combustor are compared with far-field noise measurements by direct cross-correlations. The cross-correlations and derived cross-spectral densities verify that much of the noise originates inside the combustor. A first-order fluid-mechanical perturbation model is used to predict exit plane velocity fluctuations due to internal pressure fluctuations. Far-field noise levels estimated on this basis are in good agreement with measured values. The overall noise level from the combustor/jet is found to be 10 to 20 dB higher than for an equivalent clean, cold jet at the same exit velocity.

Abdelhamid, A. N.↗

Mean flow and turbulence measurements in a Mach 5 shear layer.

Hot-wire study of turbulent mixing in the near field of a Mach 5 jet with extension of the results into the hypersonic range. Mean and fluctuating measurement data are given for the free shear layer of the 10.6-cm diameter jet which was contained in a 61-by-61 cm vacuum chamber and exhausted into a diffuser 44 cm downstream of the jet exit. An auxiliary air supply was used to equalize the static pressures in the chamber and the nozzle. The nozzle wall boundary layer was turbulent at the jet exit, providing measurement data at higher Reynolds numbers, which are also included.

Morrisette, E. L.↗

Control vane for engine exhaust flow

Vane solves problem of hot-gas exhaust impingement on curved-duct exteriors, shielding, and other nearby structure components. To eliminate secondary egress of exhaust, curved vane is placed upstream of engine exhaust duct and in close proximity to exhaust exit to induce free-stream flow more in line with exit.

Shaw, C. S.↗

Analysis of stratified and closely spaced jets exhausting into a crossflow

Procedures have been developed for determining the flow field about jets with velocity stratification exhausting into a crossflow. Jets with three different types of exit velocity stratification have been considered: (1) jets with a relatively high velocity core; (2) jets with a relatively low velocity core; and (3) jets originating from a vaned nozzle. The procedure developed for a jet originating from a high velocity core nozzle is to construct an equivalent nozzle having the same mass flow and thrust but having a uniform exit velocity profile. Calculations of the jet centerline and induced surface static pressures have been shown to be in good agreement with test data for a high velocity core nozzle. The equivalent ideal nozzle has also been shown to be a good representation for jets with a relatively low velocity core and for jets originating from a vaned nozzle in evaluating jet-induced flow fields. For the singular case of a low velocity core nozzle, namely a nozzle with a dead air core, and for the vaned nozzle, an alternative procedure has been developed. The internal mixing which takes place in the jet core has been properly accounted for in the equations of motion governing the jet development. Calculations of jet centerlines and induced surface static pressures show good agreement with test data these nozzles.

Ziegler, H.↗

Wind sensitivity studies of a non-return wind tunnel with a 216- by 432-mm (8.5- by 17.0-inches) test section, phase 2

The refinement of inlet and exit treatments were studied which would minimize the effect of external wind on the test-section flow quality of a nonreturn wind tunnel. The investigation was conducted in the Ames Research Center 40- by 80-foot Wind Tunnel which served as the wind source. Several inlets and two exits were tested at wind directions ranging from 0 to 180 degrees and at wind-to-test-section velocity ratios from zero to somewhat greater than one. For the best inlet configuration the flow quality was good, with a velocity deviation in each of the three component directions generally less. The loss in total pressure due to the inlet treatment was low: about 0.035 of the test-section dynamic pressure for the no-wind case.

Eckert, W. T.↗

Performance of a hydrogen burner to simulate air entering scramjet combustors

Tests were conducted to determine the performance of a hydrogen burner used to produce a test gas that simulates air entering a scramjet combustor at various flight conditions. The test gas simulates air in that it duplicates the total temperature, total pressure, and the volume fraction of oxygen of air at flight conditions. The main objective of the tests was to determine the performance of the burner as a function of the effective exhaust port area. The conclusions were: (1) pressure oscillations of the chugging type were reduced in amplitude to plus or minus 2 percent of the mean pressure level by proper sizing of hydrogen, oxygen, and air injector flow areas; (2) combustion efficiency remained essentially constant as the exhaust port area was increased by a factor of 3.4; (3) the mean total temperature determined from integrating the exit radial gas property profiles was within plus or minus 5 percent of the theoretical bulk total temperature; (4) the measured exit total temperature profile had a local peak temperature more than 30 percent greater than the theoretical bulk total temperature; and (5) measured heat transfer to the burner liner was 75 percent of that predicted by theory based on a flat radial temperature profile.

Russin, W. R.↗

Cold-air study of the effect on turbine stator blade aerodynamic performance of coolant ejection from various trailing-edge slot geometries. 1: Experimental results

Trailing-edge slot configurations were investigated in a two-dimensional cascade of turbine stator blades. The trailing-edge slots were incorporated into blades with round trailing edges. The five blade configurations investigated included blades with two different trailing-edge thicknesses and four different slot widths. The results of the investigation showed that there was, in general, a significant increase in primary-air efficiency due to the coolant flow, the increase varying with slot configuration. For the five configurations tested, the average percent change in primary-air efficiency per percent coolant flow varied almost linearly from zero to about 1.4 percent over a range of coolant- to primary-air exit-velocity ratios between 0 and 1.2. However, for different configurations there was considerable deviation from the average values in the lower range of exit velocity ratios.

Prust, H. W., Jr.↗

Comparison of measured and calculated velocity profiles of a laminar incompressible free jet at low Reynolds numbers

A comparison of the measured and calculated velocity profiles of a laminar, incompressible, low Reynolds number jet is presented. The experimental jet was produced by a nozzle which consists of a porous metal plate covering the end of a pipe. This nozzle produces a uniform exit velocity profile at Reynolds numbers well below those at which conventional contoured nozzles are completely filled by the boundary layer. A jet mixing analysis based on the boundary-layer equations accurately predicted the velocity field for each test condition. The Reynolds number based on nozzle diameter ranged from 50 to 1000 with jet exit velocity either 30 or 61 m/s (100 or 200 ft/sec).

Greene, G. C.↗

Use of cross-correlation measurements to investigate noise generating regions of a real jet engine and a model jet

Cross-correlations are reported of the jet static pressure fluctuations (as measured with a B and K microphone fitted with a nose cone), with the far-field radiated sound pressure. These measurements were made for various probe positions and a large number of far-field positions (at various angles). In addition, the tests were run for a number of different jet exit velocities. The measured, normalized cross-correlation functions vary between 0.004 and 0.155. These values depend upon the angular position of the far-field microphone, the jet exit Mach number, and the position of the probe. In addition, the cross-correlation technique was employed to study the symmetry of the far-field radiated sound about the jet axis. Third-octave analyses of both the probe signal and the far-field radiated sound were made. This is the first time correlation measurements have been made on a jet engine. In addition, a report is given on an extensive noise survey of a model jet. The correlations are related to sound source functions and jet source regions are discussed.

Meecham, W. C.↗

A numerical procedure for the parametric optimization of three dimensional scramjet nozzles

A numerical procedure permitting the rapid determination of the internal performance of a class of scramjet nozzle configurations is presented. The approach developed is based on the construction of quasi two dimensional simple wave networks, where lateral expansion effects are incorporated by one dimensional approximations. A numerical procedure following this approach has has been developed and results obtained are highly comparable to those obtained employing a characteristic procedure. The numerical program developed permits the parametric variation of cowl length, turning angles on the cowl and vehicle undersurface and lateral expansion and is subject to fixed constraints such as the vehicle length and nozzle exit height. The program requires uniform initial conditions at the burner exit station and yields the location of all predominant wave zones, accounting for lateral expansion effects. In addition, the program yields the detailed pressure distribution on the cowl and vehicle undersurface and calculates the nozzle thrust, lift and pitching moment.

Dash, S.↗