Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Drag coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Low-speed power effects on advanced fighter configurations with two-dimensional deflected thrust

Wind-tunnel studies at the Langley Research Center have shown that significant increases in maximum lift coefficient and stability and decreases in drag due to lift are obtained when two-dimensional vectored thrust is used in conjuction with a close-coupled canard. The configuration tested was somewhat above the theoretical minimum drag due to lift because of the sharp leading edge on the biconvex airfoil used on the wing and canard. An effort to design a new configuration which will approach the minimum drag due to lift while maintaining high-lift configurations was completed. The resulting model will incorporate a realistic planform, airfoil section, and twist for a transonic maneuvering configuration.

Paulson, J. W., Jr.↗
NASA NTRS1977

Measurements of surface-pressure and wake-flow fluctuations in the flow field of a whitcomb supercritical airfoil

Measurements of surface pressure and wake flow fluctuations were made as part of a transonic wind tunnel investigation into the nature of a supercritical airfoil flow field. Emphasis was on a range of high subsonic Mach numbers and moderate lift coefficients corresponding to the development of drag divergence and buffeting. Fluctuation data were analyzed statistically for intensity, frequency content, and spatial coherence. Variations in these parameters were correlated with changes in the mean airfoil flow field.

Roos, F. W.↗
NASA NTRS1980

Preliminary design characteristics of a subsonic business jet concept employing an aspect ratio 25 strut braced wing

The advantages of replacing the conventional wing on a transatlantic business jet with a larger, strut braced wing of aspect ratio 25 were evaluated. The lifting struts reduce both the induced drag and structural weight of the heavier, high aspect ratio wing. Compared to the conventional airplane, the strut braced wing design offers significantly higher lift to drag ratios achieved at higher lift coefficients and, consequently, a combination of lower speeds and higher altitudes. The strut braced wing airplane provides fuel savings with an attendant increase in construction costs.

Turriziani, R. V.↗
NASA NTRS1987

Experimental and theoretical study of propeller spinner/shank interference

A fundamental investigation into the aerodynamic interference associated with propeller spinner and shank regions has been conducted. The research program involved a theoretical assessment of solutions previously proposed, followed by a systematic experimental study to supplement the existing data base. As a result, a refined computational procedure has been established for prediction of interference effects in terms of either interference drag or propeller thrust and torque coefficients. These quantities have been examined with attention to engineering parameters such as spinner finess ratio, blade shank form, and number of blades. Also, cascade effects and spinner/shank juncture interference have been semi-empirically modeled using existing theories and placed into a compatible form with an existing propeller performance code.

Cornell, C. C.↗
NASA NTRS1987

Model helicopter performance degradation with simulated ice shapes

An experimental program using a commercially available model helicopter has been conducted in the Texas A&M University Subsonic Wind Tunnel to investigate main rotor performance degradation due to generic ice. The simulated ice, including both primary and secondary formations, was scaled by chord from previously documented artificial ice accretions. Base and iced performance data were gathered as functions of fuselage incidence, blade collective pitch, main rotor rotational velocity, and freestream velocity. It was observed that the presence of simulated ice tends to decrease the lift to equivalent drag ratio, as well as thrust coefficient for the range of velocity ratios tested. Also, increases in torque coefficient due to the generic ice formations were observed. Evaluation of the data has indicated that the addition of roughness due to secondary ice formations is crucial for proper evaluation of the degradation in main rotor performance.

Tinetti, Ana F.↗
NASA NTRS1989

Separation control on an airfoil by periodic forcing

The introduction of transverse velocity fluctuations into a separated shear layer on an airfoil at high angles of attack is presently demonstrated to be an effective separation-control technique. Airfoil aerodynamic characteristics, including poststall lift and drag as well as maximum lift coefficient and stall angle, all exhibited improvements controlled forcing at 20 deg angle of attack led to an increased spreading of the mean velocity profile, together with increased turbulence activity; separation moved from the leading edge to about 80 percent of chord.

Bar-Sever, A.↗
NASA NTRS1993

Hypersonic aerodynamic characteristics for Langley Test Technique Demonstrator

Experimental longitudinal and lateral-directional aerodynamic characteristics were obtained for a generic transatmospheric vehicle concept referred to as the Langley Test Technique Demonstrator. The baseline configuration, without engine modules, was longitudinally and directionally unstable over the hypersonic Mach number range of the investigation and exhibited untrimmed (L/D)max levels between 2.6 and 2.8. Adding various engine modules to the baseline configuration produced mainly, degradations in lift-to-drag ratio. In general, longitudinal aerodynamic coefficients predicted with an engineering code referred to as Aerodynamic Preliminary Analysis System (APAS) were in qualitative, and often quantitative agreement with measurement.

Phillips, W. P.↗
NASA NTRS1933

The Aerodynamic Effect of a Retractable Landing Gear

Tests were conducted in the N.A.C.A. full scale wind tunnel at the request of the Army Air Corps to determine the effect of retractable landing gear openings in the bottom surface of a wing upon the characteristics of a Lockheed Altair airplane. The tests were extended to include the determination of the lift and drag characteristics throughout the angle-of-attack range with the landing gear both retracted and extended. Covering the wheel openings in the wing with sheet metal when the wheels were extended reduced the drag only 2 percent at a lift coefficient of 1.0, which was assumed for the take-off condition. Therefore, the wheel openings in the bottom side of the wing have a negligible effect upon the take-off of the airplane. Retracting the landing gear reduced the minimum drag of the complete airplane 50 percent.

Defrance, Smith J↗
NASA NTRS1947

Wind Tunnel Development of Means to Alleviate Buffeting of the North American XP-82 Airplane at High Speeds

This report presents the results of wind-tunnel tests of a 0.22-scale model of the North American XP-82 airplane with several modifications designed to reduce the buffeting of the airplane. The effects of various modifications on the air flow over the model are shown by means of photographs of tufts. The drag, lift, and pitching-moment coefficients of the model with several of the modifications are shown. The result indicate that, by reflexing the trailing edge of the center section of the wing and modifying the radiator air-scoop gutter and the inboard lower-surface wing fillets, the start of buffeting can be delayed from a Mach number of 0.70 to 0.775, and that the diving tendency of the airplane would be eliminated up to a Mach number of 0.80.

Anderson, Joseph L.↗
NASA NTRS2013

Space Weather Impacts to Conjunction Assessment: A NASA Robotic Orbital Safety Perspective

National Aeronautics and Space Administration (NASA) recognizes the risk of on-orbit collisions from other satellites and debris objects and has instituted a process to identify and react to close approaches. The charter of the NASA Robotic Conjunction Assessment Risk Analysis (CARA) task is to protect NASA robotic (unmanned) assets from threats posed by other space objects. Monitoring for potential collisions requires formulating close-approach predictions a week or more in the future to determine analyze, and respond to orbital conjunction events of interest. These predictions require propagation of the latest state vector and covariance assuming a predicted atmospheric density and ballistic coefficient. Any differences between the predicted drag used for propagation and the actual drag experienced by the space objects can potentially affect the conjunction event. Therefore, the space environment itself, in particular how space weather impacts atmospheric drag, is an essential element to understand in order effectively to assess the risk of conjunction events. The focus of this research is to develop a better understanding of the impact of space weather on conjunction assessment activities: both accurately determining the current risk and assessing how that risk may change under dynamic space weather conditions. We are engaged in a data-- ]mining exercise to corroborate whether or not observed changes in a conjunction event's dynamics appear consistent with space weather changes and are interested in developing a framework to respond appropriately to uncertainty in predicted space weather. In particular, we use historical conjunction event data products to search for dynamical effects on satellite orbits from changing atmospheric drag. Increased drag is expected to lower the satellite specific energy and will result in the satellite's being 'later' than expected, which can affect satellite conjunctions in a number of ways depending on the two satellites' orbits and the geometry of the conjunction. These satellite time offsets can form the basis of a new technique under development to determine whether space weather perturbations, such as coronal mass ejections, are likely to increase, decrease, or have a neutral effect on the collision risk due to a particular close approach.

Ghrist, Richard↗
NASA NTRS1942

Investigation of a Low-Drag Gun Port in the NACA Two-Dimensional Low-Turbulence Tunnel

Tests were made in the NACA two-dimensional low-turbulence tunnel of three gun ports with a height of approximately 4 percent of the chord faired into an NACA 66,2-213 low-drag-airfoil section by bulging the section at the gun port. Gun ports faired in this manner had practically no effect on the maximum lift and the critical compressibility speed of the section and showed only small increase in the drag in the range of lift coefficients for high-speed and cruising-flight conditions.

Horton, Elmer A.↗
NASA NTRS2018

Pterodactyl: Integrated Control Design for Precision Targeting of Deployable Entry Vehicles

Deployable Entry Vehicles (DEVs) enable in-situ scientific exploration at destinations with atmospheres across the solar system. Because they stow in a compact form and deploy only when ready to enter the atmosphere, DEVs relax the volume constraint imposed by rigid aeroshells. This work seeks to do for a DEV what the Wright Brothers did to propel modern day aviation: develop the guidance and control (G&C) methods that will make maneuvering and precision landing of DEV a reality. The Pterodactyl project objective is to deliver an integrated G&C methodology for a DEV, based on a detailed analysis that utilizes a Multi-disciplinary, Design, Analysis and Optimization (MDAO) framework. The current state-of-the-art for blunt body entry, G&C is rooted in the precision landing of vehicles such as Mars Science Laboratory (MSL) and Apollo, which used a propulsive reaction control system (RCS) to steer. Recent research has taken a particular interest in non-propulsive control for DEVs, including direct force control (angle of attack modulation via control surfaces or mass movement) and drag modulation (discrete change in ballistic coefficient). Using the MDAO framework that includes a guidance and control model to explore multiple control concepts for a DEV will shed light on the best design approach for these vehicles. In Pterodactyl, we will complete this study for a novel DEV concept, and then we will fabricate a functional prototype to help validate the design. The project is expected to down-select to a final control architecture by the end of 2018, and complete fabrication of the prototype by the end of 2019.The DEV chosen for detailed study in this project is the Adaptable Deployable Entry and Placement Technology (ADEPT). ADEPT uses a revolutionary 3D-woven carbon fabric that is foldable, can serve as primary structure, and can survive the extreme heating environment of atmospheric entry. The specific configuration of ADEPT under investigation is called Lifting Nano-ADEPT (LNA). LNA is designed for secondary payloads missions that require precision landing either for scientific objectives at a target destination or for payload recovery at Earth.The MDAO framework being created through this research, called COBRA-Pt (Composite Beam Roll-Up Solar Array-Prototype), will combine three critical elements of the system design: a guidance algorithm with Monte Carlo, a parametric control model, and vehicle geometry details. Novel control models being studied are deployable aerodynamic surfaces as well as shape morphing. These concepts will be compared at the system level with a more traditional propulsive RCS by comparing several key performance parameters. Upon completion of the design study, a functional prototype of LNA will be fabricated that will include the integration of guidance software and relevant control actuators. We expect this study will provide critical data that could feed into the development of an Earth-based flight test of LNA. The COBRA-Pt framework will provide a modular system by which to study any DEV concept in any atmosphere.

Smith, Brandon↗
NASA NTRS1955

Transonic Free-Flight Investigation of the Longitudinal Aerodynamic Characteristics of a 1/10-Scale Steel-Wing Model of the Northrop MX-775A Missile with Leading-Edge Extensions, Inboard Trailing-Edge Flaps, and a Speed Brake on the Vertical Tail

Results are presented of a free-flight investigation between Mach numbers of 0.7 to 1.3 and Reynolds numbers of 3.1 x 10(exp 6) to 7.0 x 10(exp 6) to determine the longitudinal aerodynamic characteristics of the Northrop MX-775A missile. This missile has a weng, body, and vertical tail, but has no horizontal tail. The basic wing plan form has an aspect ratio of 5.5, 45 deg of sweepback of the 0.406 streamwise chord line, and a taper ratio of 0.4. A 1/10-scale steel-wing model of the missile was flown with modifications to the basic wing plan form consisting of leading-edge chord-extensions deflected 7 deg downward together with the forward 15 percent of the wing chord, and inboard trailing-edge flaps deflected 5 deg downward. In addition, the model had a static-pressure tube mounted at the tip of the vertical tail for position-error measurements and had a speed brake also mounted on the vertical tail to trim the model to positive lift coefficients and to permit determination of the trim and drag effectiveness of the brake. The data are uncorrected for the effects of wing elasticity, but experimental wing influence coefficients are presented.

Arbic, R. G.↗
NASA NTRS1937

Theoretical span loading and moments of tapered wings produced by aileron deflection

The effect of tapered ailerons on linearly tapered wings is theoretically determined. Four different aileron spans are considered for each of three wing aspect ratios and each of four wing taper ratios. The change in lift on one half of the wing, the rolling moment, the additional induced drag, and the yawing moment, due to aileron deflection, are represented by non dimensional coefficients. Similar coefficients are given for the damping and yawing moments, the additional drag, and the change in lift, due to rolling. It was found possible to effect a fairly close agreement between the theoretical and experimental rolling moments by introducing into the theoretical expression for the rolling moment an effective change in angle of attack obtained from an analysis of flap data. The theoretical curves show that the highly tapered wing with long ailerons has a lower ratio of yawing to rolling moment and a lower additional induced drag than wings with less taper.

Pearson, H A↗
NASA NTRSDate not supplied

Aeroelastic Trim Drag Optimization of Mach 0.8 Transonic Truss-Braced Wing Aircraft using High-Lift Devices and Control Surfaces

This paper presents an aeroelastic trim drag optimization study of the Mach 0.8 Transonic Truss-Braced Wing (TTBW) aircraft using the High-lift devices and control surfaces. An aero-structural analysis solver VSPAERO with transonic small disturbance, integral boundary-layer, and wing-strut interference corrections coupled to mode shapes computed by NASTRAN using the Galerkin method is developed to provide a rapid aircraft aeroelastic performance evaluation. Three different flight conditions corresponding to Mach 0.8 are selected for the aeroelastic trim drag optimization at the design and off-design cruise lift coefficients. The preliminary optimization results show that the TTBW aircraft with the optimized deflection of the high-lift devices and control surfaces achieves a drag reduction of about 8.2 counts, 6.5 counts, and 9.7 counts corresponding to the lift coefficients 0.661, 0.695, and 0.729, respectively. A high-fidelity CFD solver FUN3D is used to verify the aeroelastic trim drag optimization.

TTBW↗
NASA NTRS1984

An analysis of the high-latitude thermospheric wind pattern calculated by a thermospheric general circulation model. I - Momentum forcing

A diagnostic processor (DP) was developed for analysis of hydrodynamic and thermodynamic processes predicted by the NCAR thermospheric general circulation model (TGCM). The TGCM contains a history file on the projected wind, temperature and composition fields at each grid point for each hour of universal time. The DP assimilates the history file plus ion drag tensors and drift velocities, specific heats, coefficients of viscosity, and thermal conductivity and calculates the individual forcing terms for the momentum and energy equations for a given altitude. Sample momentum forcings were calculated for high latitudes in the presence of forcing by solar radiation and magnetospheric convection with a 60 kV cross-tail potential, i.e., conditions on Oct. 21, 1981. It was found that ion drag and pressure forces balance out at F region heights where ion drift velocities are small. The magnetic polar cap/auroral zone boundary featured the largest residual force or net acceleration. Diurnal oscillations were detected in the thermospheric convection, and geostrophic balance was dominant in the E layer.

Killeen, T. L.↗
NASA NTRS1961

Effects at Mach Numbers of 1.61 and 2.01 of Camber and Twist on the Aerodynamic Characteristics of Three Swept Wings Having the Same Planform

An investigation has been made at Mach numbers of 1.61 and 2.01 to determine the aerodynamic characteristics of three wings having a sweepback of 50 deg at the quarter-chord line, a taper ratio of 0.20, an NACA 65A005 thickness distribution, and an aspect ratio of 3.5. One wing was flat, one had at each spanwise station an a = 0 mean line modified to have a maximum height of 4-percent chord, and one had a linear variation of twist with 6 deg of washout at the tip. Tests were made with natural and fixed transition at Reynolds numbers ranging from 1.2 x 10(exp 6) to 3.6 x 10(exp 6) through an angle-of-attack range of -20 deg to 20 deg. When compared with the flat wing, the effect of the linear variation of twist with 6 deg of washout at the tip was to increase the lift-drag ratio when the leading edge was subsonic; but little increase in lift-drag ratio was obtained when the leading edge was supersonic. Pitching moment was increased and gave a positive trim point without greatly affecting the rate of change of pitching moment with lift coefficient. For the cambered wing the high minimum drag resulted in comparatively low lift-drag ratios. In addition, the pitching moments were decreased so that a negative trim point was obtained.

Landrum, Emma Jean↗