Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Data engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Microturbulence study of the isotope effect

The influence of the ion mass on the dynamics of magnetized plasmas is an important challenge in fusion research. The discrepancies between the improvement of the magnetic confinement with the ion mass in tokamak experiments and diffusive turbulent transport predictions have remained unexplained for several decades. We refer to this phenomenon as the isotope effect. In this paper, we study this effect with gyrokinetic theory using the GENE code. We find several sets of plasma parameters that correspond to low wavenumber turbulence for which the isotope effect is present, although the intensity is smaller than the experimental observations. We also relate these results to the zonal flow intensity of the system, which is characterized by the average shear flow rate.

42 ENGINEERING↗

Mechanical properties as an indicator of interstitials in niobium for superconducting accelerator cavities

A preliminary investigation was conducted into the feasibility of using simple mechanical properties experiments to evaluate interstitial impurity uptake from processing environments. Two types of tests were examined: tensile tests and complex modulus measurements using a dynamic mechanical analyzer (DMA). For the tensile tests, samples were cut from a single crystal of niobium, with the same orientation, and then prepared following different procedures. Significant differences were observed during tensile tests, with yielding strength and strain-to-failure clearly related to interstitial uptake. When the strain rate was reduced by an order of magnitude, the strain-to-failure was reduced by 18 % indicating that interstitial hydrogen is responsible for this behavior. For the complex modulus measurement, polycrystalline samples from different locations of two different ingots were examined at a frequency of 1.0 Hz while the temperature was increased at the rate of 1.0 °C per minute. Anaelastic peaks were found for C, N, and O in all samples, but the lower limit of the system did not allow for detection of a peak for H. It is concluded that mechanical properties could be developed as a measurement tool to guide the development of processing methods for producing reduced interstitial content material, but additional research, and uncertainty analysis, is required for these tools to be reliable in this application.

36 MATERIALS SCIENCE↗

The role of magnetic anisotropy in the magnetoresistance of Cr 2 O 3 /Al 2 O 3 thin film antiferromagnets

The magnetic states of antiferromagnetic insulating thin films are a promising medium for information storage, but characterization of these states has proven to be challenging. One approach is via magnetotransport measurements in an adjacent heavy metal layer. To this end, we synthesized and characterized a series of Cr 2 O 3 films and bilayers on Al 2 O 3 substrates with three different orientations: m-plane, a-plane, and c-plane. X-ray diffraction results demonstrated orientation control of the Cr 2 O 3 thin film, with m-plane films displaying a higher degree of mosaic spread than the a- and c-plane films. Reciprocal space maps showed that the films are mostly relaxed, although there was a small and different degree of strain in each orientation. The m-plane films were under 2% compressive strain, the a-plane film was under 0.5% compressive strain, and the c-plane film was completely relaxed to bulk values. To probe the magnetic state of the films, we measured the angular dependent magnetoresistance of Cr 2 O 3 /Pt bilayers for each orientation. We found a nontrivial temperature dependence of the sign of the magnetoresistance, pointing to the complex interplay between the exchange and anisotropy energies that vary with orientation. We propose that strain and mosaic spread may contribute to a difference in magnetic anisotropies among the samples and the resulting temperature dependence of the magnetoresistance. This work demonstrates the importance of considering the competition between antiferromagnetic exchange and magnetic anisotropy when storing information in the spin state of an antiferromagnetic insulator.

42 ENGINEERING↗

Shape effects on the local dynamics of suspensions of spheroidal particles

The effect of shape on the dynamics of suspensions of non-spherical heavy particles is examined by fully resolved numerical simulations of oblate and prolate spheroids, as well as spheres, for a density ratio of ten, volume fractions ranging from 0.5% to 5%, and Reynolds numbers between 20 and 30. The dynamics is determined both by the interactions of the particles with the fluid as well as by collisions, with the number and importance of collisions increasing with volume fractions. A single isolated oblate or prolate spheroid falling under gravity generally falls broadside on, for the governing parameters examined here, and at low-volume fractions, the majority of particles in a suspension fall that way. At higher-volume fractions, the orientation is more random. The slip velocity decreases as the volume fraction increases for all shapes, as expected, but the effect of the shape is much less than seen for a single particle. Furthermore, this seems to be due to two effects. For all volume fractions, the most deformed particles cluster more than spheres and less deformed particles, which increases their slip velocity. As the concentration increases, the increased particle interactions also causes more particles to fall short side-on, which reduces the frontal area and the resulting drag, increasing the slip velocity. This second effect is, of course, absent for spherical particles.

42 ENGINEERING↗

Causal discovery from data assisted by large language models

Knowledge-driven discovery of novel materials necessitates the development of causal models for property emergence. While in the classical physical paradigm, the causal relationships are deduced based on physical principles or via experiment, the rapid accumulation of observational data necessitates learning causal relationships between dissimilar aspects of material structure and functionalities based on observations. For this, it is essential to integrate experimental data with prior domain knowledge. Here, we demonstrate this approach by combining high-resolution scanning transmission electron microscopy data with insights derived from large language models (LLMs). By applying ChatGPT to domain-specific literature, such as arXiv papers on ferroelectrics, and combining the obtained information with data-driven causal discovery, we construct adjacency matrices for directed acyclic graphs that map the causal relationships between structural, chemical, and polarization degrees of freedom in Sm-doped BiFeO 3 . This approach enables us to hypothesize how synthesis conditions influence material properties and guides experimental validation. Furthermore, the ultimate objective of this work is to develop a unified framework that integrates LLM-driven literature analysis with data-driven discovery, facilitating the precise engineering of ferroelectric materials by establishing clear connections between synthesis conditions and their resulting material properties.

Causal inference↗

Antigen clasping by two antigen-binding sites of an exceptionally specific antibody for histone methylation

Antibodies have a well-established modular architecture wherein the antigen-binding site residing in the antigen-binding fragment (Fab or Fv) is an autonomous and complete unit for antigen recognition. Here, we describe antibodies departing from this paradigm. We developed recombinant antibodies to trimethylated lysine residues on histone H3, important epigenetic marks and challenging targets for molecular recognition. Quantitative characterization demonstrated their exquisite specificity and high affinity, and they performed well in common epigenetics applications. Surprisingly, crystal structures and biophysical analyses revealed that two antigen-binding sites of these antibodies form a head-to-head dimer and cooperatively recognize the antigen in the dimer interface. This “antigen clasping” produced an expansive interface where trimethylated Lys bound to an unusually extensive aromatic cage in one Fab and the histone N terminus to a pocket in the other, thereby rationalizing the high specificity. A long-neck antibody format with a long linker between the antigen-binding module and the Fc region facilitated antigen clasping and achieved both high specificity and high potency. Antigen clasping substantially expands the paradigm of antibody–antigen recognition and suggests a strategy for developing extremely specific antibodies.

59 BASIC BIOLOGICAL SCIENCES↗

Quantum Computing by Coherent Cooling

Interesting problems in quantum computation take the form of finding low-energy states of (pseudo)spin systems with engineered Hamiltonians that encode the problem data. Motivated by the practical possibility of producing very low-temperature spin systems, we propose and exemplify the possibility to compute by coupling the computational spins to a quantum coherent bath that serves as a heat sink. The quantum tunneling effect provides additional cooling channels to accelerate the cooling process. Here, we demonstrate both analytically and numerically that this strategy can achieve a quantum advantage in the unstructured search problem.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Cyber Dumpster Diving: Creating New Software Systems for Less

Modern scientific software is daunting in its breadth and complexity. From massively parallel simulations running on the world’s largest supercomputers to visualizations and user support environments that manage ever-growing, complex data collections, the challenges for software engineers are plentiful indeed.

software architecture↗

An Investigation on the Pollen-Induced Soiling Losses in Utility-Scale PV Plants

Soiling, the accumulation of dust and other contaminants on the surface of photovoltaic (PV) modules, is a common factor that can negatively impact the performance of PV systems. In this study, the authors aim to analyze the impact of pollen on soiling losses in PV systems located in North Carolina, USA, particularly during the spring season. The performance data of two utility-scale PV plants was collected and analyzed using the two soiling extraction methods. Environmental data, including croplands and vegetation was also collected and analyzed to identify correlations with soiling losses. The results of the study may help improve understanding of necessary operation and maintenance activities for PV plants and provide new insights into the phenomenon of pollen deposition on PV systems.

correlation↗

Design of the Trigger Interface and Distribution Board for CEBAF 12 GeV Upgrade

The design of the Trigger Interface and Distribution (TID) board for the 12 GeV Upgrade at the Continuous Electron Beam Accelerator Facility (CEBAF) at TJNAL is described. The TID board distributes a low jitter system clock, synchronized trigger, and synchronized multi-purpose SYNC signal. The TID also initiates data acquisition for the crate. With the TID boards, a multi-crate system can be setup for experiment test and commissioning. The TID board can be selectively populated as a Trigger Interface (TI) board, or a Trigger Distribution (TD) board for the 12 GeV upgrade experiments. When the TID is populated as a TI, it can be located in the VXS crate and distribute the CLOCK/TRIGGER/SYNC through the VXS P0 connector; it can also be located in the standard VME64 crate, and distribute the CLOCK/TRIGGER/SYNC through the VME P2 connector or front panel. It initiates the data acquisition for the front crate where the TI is positioned in. When the TID is populated as a TD, it fans out the CLOCK/TRIGGER/SYNC from trigger supervisor to the front end crates through optical fibres. The TD monitors the trigger processing on the TIs, and gives feedback to the TS for trigger flow control. Field Programmable Gate Arrays (FPGA) is utilised on TID board to provide programmability. The TID boards were intensively tested on the bench, and various setups.

CEBAF upgrade↗

Anomaly Detection for Discrete Sequences: A Survey

This survey attempts to provide a comprehensive and structured overview of the existing research for the problem of detecting anomalies in discrete/symbolic sequences. The objective is to provide a global understanding of the sequence anomaly detection problem and how existing techniques relate to each other. The key contribution of this survey is the classification of the existing research into three distinct categories, based on the problem formulation that they are trying to solve. These problem formulations are: 1) identifying anomalous sequences with respect to a database of normal sequences; 2) identifying an anomalous subsequence within a long sequence; and 3) identifying a pattern in a sequence whose frequency of occurrence is anomalous. We show how each of these problem formulations is characteristically distinct from each other and discuss their relevance in various application domains. We review techniques from many disparate and disconnected application domains that address each of these formulations. Within each problem formulation, we group techniques into categories based on the nature of the underlying algorithm. For each category, we provide a basic anomaly detection technique, and show how the existing techniques are variants of the basic technique. This approach shows how different techniques within a category are related or different from each other. Our categorization reveals new variants and combinations that have not been investigated before for anomaly detection. We also provide a discussion of relative strengths and weaknesses of different techniques. We show how techniques developed for one problem formulation can be adapted to solve a different formulation, thereby providing several novel adaptations to solve the different problem formulations. We also highlight the applicability of the techniques that handle discrete sequences to other related areas such as online anomaly detection and time series anomaly detection.

99 GENERAL AND MISCELLANEOUS↗

Quantify Resonance Inspection with Finite Element-Based Modal Analyses

Resonance inspection uses the natural acoustic resonances of a part to identify anomalous parts. Modern instrumentation can measure the many resonant frequencies rapidly and accurately. Sophisticated sorting algorithms trained on sets of good and anomalous parts can rapidly and reliably inspect and sort parts. This paper aims at using finite-element-based modal analysis to put resonance inspection on a more quantitative basis. A production-level automotive steering knuckle is used as the example part for our study. First, the resonance frequency spectra for the knuckle are measured with two different experimental techniques. Next, scanning laser vibrometry is used to determine the mode shape corresponding to each resonance. The material properties including anisotropy are next measured to high accuracy using resonance spectroscopy on cuboids cut from the part. Then, finite element model (FEM) of the knuckle is generated by meshing the actual part geometry obtained with computed tomography (CT). The resonance frequencies and mode shapes are next predicted with a natural frequency extraction analysis after extensive mesh size sensitivity study. The good comparison between the predicted and the experimentally measured resonance spectra indicate that finite-element-based modal analyses have the potential to be a powerful tool in shortening the training process and improving the accuracy of the resonance inspection process for a complex, production level part. The finite element based analysis can also provide a means to computationally test the sensitivity of the frequencies to various possible defects such as porosity or oxide inclusions especially in the high stress regions that the part will experience in service.

42 ENGINEERING↗

Degradation Modeling and Reliability Assessment of Capacitors

The degradation of capacitors under accelerated stress conditions occur in a monotonic and non-linear fashion. Several efforts have been made to model the degradation behavior of capacitor considering either physics-of-failure models or statistical models and subsequently estimate its reliability and lifetime parameters. But most of these models fail to reflect the physical properties of the degradation path, which varies according to several intrinsic and extrinsic factors. These factors introduce random and temporal uncertainty among the population of capacitors. The gamma stochastic process can model both type of uncertainties among the population of capacitors. In this paper, we model the capacitor degradation by non-homogeneous gamma stochastic process in which both the model parameters (shape and scale) are dependent on stress variables. The model parameters are estimated using the maximum likelihood estimation approach.

42 ENGINEERING↗

Optical information transfer through random unknown diffusers using electronic encoding and diffractive decoding

Free-space optical information transfer through diffusive media is critical in many applications, such as biomedical devices and optical communication, but remains challenging due to random, unknown perturbations in the optical path. We demonstrate an optical diffractive decoder with electronic encoding to accurately transfer the optical information of interest, corresponding to, e.g., any arbitrary input object or message, through unknown random phase diffusers along the optical path. This hybrid electronic-optical model, trained using supervised learning, comprises a convolutional neural network-based electronic encoder and successive passive diffractive layers that are jointly optimized. After their joint training using deep learning, our hybrid model can transfer optical information through unknown phase diffusers, demonstrating generalization to new random diffusers never seen before. The resulting electronic-encoder and optical-decoder model was experimentally validated using a 3D-printed diffractive network that axially spans <70λ, where λ = 0.75 mm is the illumination wavelength in the terahertz spectrum, carrying the desired optical information through random unknown diffusers. The presented framework can be physically scaled to operate at different parts of the electromagnetic spectrum, without retraining its components, and would offer low-power and compact solutions for optical information transfer in free space through unknown random diffusive media.

36 MATERIALS SCIENCE↗

Scoreboard

Emerging HPC machines have given rise to enhanced compute power that far outstrips the machine's ability to save large scale results for post-processing. To combat this, in situ data analysis techniques are slowly being adopted. With in situ data management favoring workflows composed of multiple simulations and analyses connected in transit on heterogeneous machines, scientists and engineers need a tool that enables them to create data extracts, visualizations, and interactively monitor and steer their simulations. Scoreboard Phase II is a next generation analysis software that supports composite in transit workflows on heterogeneous architectures and restores interactivity to in situ data analysis through simulation monitoring and computational steering. Scoreboard provides a simulation dashboard with graphs of metrics over time, controls for setting custom simulation steering parameters, controls for managing the set of data extracts being produced in the simulation, as well as the ability to explore data extracts, all from a web browser. Realizing the vision outlined in this project required research into making a system that integrates end to end from simulations all the way to the user. In situ tools generally suffer from complexity and excessive software dependencies. Scoreboard, by contrast, is easy to build and integrate into simulation codes and it provides first class FORTRAN support. The Scoreboard library is capable of in situ and in transit data analysis that can produce data extracts commonly needed for Computational Fluid Dynamics (CFD) analysis. Simulations can transparently stage data in transit to a Scoreboard Endpoint program, which can accept their data and produce the requested data extracts. This lets simulations return to their work while the Endpoint works on the analysis. Efficiently staging the data at scale was a topic of this research. Scoreboard provides the means to let the user manage data extracts and monitor/steer many simulations from a web browser. This area of the research focused on discovery of in transit network components to expose and control their steering parameters within an interactive browser-based user interface that includes: system topology, gathered metrics, notifications, dynamically-generated steering controls, and exploration of visualization data products.

Whitlock, BradJoseph [Intelligent Light] (00000001↗

Neural Network Export Package (nexport) v0.1.0

nexport is a lightweight python 3 package which enables neural network developers to export the weights and biases of trained networks to useful file types. It provides I/O support for applications which require specific data types for instantiating neural networks in various inference environments. It was initially developed to support exporting to the data structure used by 'inference-engine', a Fortran inference package.

Welsman, Jordan↗