Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Condition reports”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Vibration damping characteristics of graphite/epoxy composites for large space structures

Limited data on extensional and flexural damping of small specimens of graphite/epoxy and unreinforced epoxy resin were obtained. Flexural damping was measured using a forced vibration technique based on resonant flexural vibration of shaker excited double cantilever specimens. Extensional damping was measured by subjecting similar specimens to low frequency sinusoidal oscillation in a servohydraulic tensile testing machine while plotting load versus extensional strain. Damping was found to vary slowly and continuously over the frequency range 0.01 - 1000 Hz, and no drastic transitions were observed. Composite damping was found to be less than neat resin damping. Comparison of small specimen damping values with assembled column damping values seems to indicate that, for those materials, material damping is more important than joint damping. The data reported was limited not by the test apparatus, but by signal conditioning and data acquisition. It is believed that filtering of the strain gage signals and the use of digital storage with slow playback will make it possible to extend the frequency and amplitude ranges significantly.

Gibson, R. F.↗
NASA NTRS1982

Direct observation of interface instability during crystal growth

The general aim of this investigation was to study interface stability and solute segregation phenomena during crystallization of a model system. Emphasis was to be placed on direct observational studies partly because this offered the possibility at a later stage of performing related experiments under substantially convection-free conditions in the space shuttle. The major achievements described in this report are: (1) the development of a new model system for fundamental studies of crystal growth from the melt and the measurement of a range of material parameters necessary for comparison of experiment with theory. (2) The introduction of a new method of measuring segregation coefficient using absorption of a laser beam by the liquid phase. (3) The comparison of segregation in crystals grown by gradient freezing and by pulling from the melt. (4) The introduction into the theory of solute segregation of an interface field term and comparison with experiment. (5) The introduction of the interface field term into the theories of constitutional supercooling and morphological stability and assessment of its importance.

Tiller, W. A.↗
NASA NTRS1983

Experimental verification of the multistage depressed collector design procedure for a high-perveance, helix-type, traveling-wave tube

The validity of a computational procedure for the design of multistage depressed collectors (MDC's) is demonstrated for a traveling wave tube (TWT) with a perveance of .00000123. The MDC is used with spent-beam refocusing to improve substantially the efficiency of the TWT. Reports on this subject have verified, under a variety of operating conditions, the MDC design procedure for TWT's with lower perveance. The design procedure is based on two computer programs that create a mathematical model of the electric and magnetic fields of the TWT refocuser MDC system and its electron beam. The two principal outputs of the analysis are a description of the radiofrequency (RF) performance of the TWT and the trajectories of representatives groups of charges from the input of the TWT to their points of interception on the MDC electrodes.

Dayton, J. A., Jr.↗
NASA NTRS1983

Application of in-flight thrust determination uncertainty

A numerical example is given of a previously proposed methodology for the evaluation of in-flight thrust measurement uncertainty, using data extracted from a performance report comparing two different missile prototypes under a variety of flight conditions. Attention is given to the data for the AGM-68B Air Launched Cruise Missile, which is powered by the F107 dual-spool, mixed flow turbofan engine. Assessments are made of the definition of the measurement process, instrumentation error estimation, the propagation of errors to thrust calculation, mathematical model errors, the in-flight thrust error component, and correction to standard conditions. It is concluded that in-flight thrust measurement uncertainty limits can be evaluated from measurement system error analysis results and test data for the missile evaluation process presently described.

Adams, G. R.↗
NASA NTRS1987

The distribution of gas and galaxies around the distant quasar PKS 1614 + 051

The results of narrow-band and broad-band filter observations of the region surrounding the z = 3.21 quasars, PKS 1614 + 051, made under subarcsec seeing conditions with the 3.6 m CFHT telescope at Mauna Kea are reported. The nuclear region of the Lyman-alpha companion to the quasar is resolved with a FWHM of about 0.9 arcsec A magnitude fainter. Limits on detectable continuum flux from this object suggest that it is a gas cloud interacting with the quasar, and its emission is consistent with simple photoionization by the quasar. However, the presence of several galaxies around the periphery of the quasar is noted. A search of 11 additional quasars at z greater than 3 has failed to show any other such systems. It is argued that this is consistent with the statistics of extended emission line systems in low-z quasars.

Hu, Esther M.↗
NASA NTRS1988

The NASA atomic oxygen effects test program

The NASA Atomic Oxygen Effects Test Program was established to compare the low earth orbital simulation characteristics of existing atomic oxygen test facilities and utilize the collective data from a multitude of simulation facilities to promote understanding of mechanisms and erosion yield dependence upon energy, flux, metastables, charge, and environmental species. Four materials chosen for this evaluation include Kapton HN polyimide, FEP Teflon, polyethylene, and graphite single crystals. The conditions and results of atomic oxygen exposure of these materials is reported by the participating organizations and then assembled to identify degrees of dependency of erosion yields that may not be observable from any single atomic oxygen low earth orbital simulation facility. To date, the program includes 30 test facilities. Characteristics of the participating test facilities and results to date are reported.

Banks, Bruce A.↗
NASA NTRS1989

Space plasma contractor research, 1988

Results of experiments conducted on hollow cathode-based plasma contractors are reported. Specific tests in which attempts were made to vary plasma conditions in the simulated ionospheric plasma are described. Experimental results showing the effects of contractor flowrate and ion collecting surface size on contactor performance and contactor plasma plume geometry are presented. In addition to this work, one-dimensional solutions to spherical and cylindircal space-charge limited double-sheath problems are developed. A technique is proposed that can be used to apply these solutions to the problem of current flow through elongated double-sheaths that separate two cold plasmas. Two conference papers which describe the essential features of the plasma contacting process and present data that should facilitate calibration of comprehensive numerical models of the plasma contacting process are also included.

Williams, John D.↗
NASA NTRS1991

Mach 2 and Mach 3 mixing and combustion in scramjets

Experimental and theoretical studies are being conducted to explore techniques to enhance mixing in scramjet combustors using parallel fuel injection from the base of swept and unswept wall-mounted ramps. Parallel injection may be useful in high speed scramjets due to the thrust contributed by the momentum of expanding fuel that has been heated in the vehicle cooling cycle. The experiments reported herein were conducted using Mach 2 and 3 combustor inlet conditions. Supporting computational and cold flow studies indicated that the observed enhanced mixing for the swept ramp configuration is primarily due to the substantially higher degree of vorticity and entrainment generated by the swept trailing edges.

Northam, G. B.↗
NASA NTRS1991

Supersonic mixing and combustion in scramjets

Experimental and theoretical studies are being conducted to explore techniques to enhance mixing in scramjet combustors using parallel fuel injection from the base of swept and unswept wall-mounted ramps. The experiments reported herein were conducted using Mach 2 and 3 combustor inlet conditions. Supporting computational and cold flow studies indicated that the observed enhanced mixing for the swept ramp configuration is primarily due to the substantially higher degree of vorticity and entrainment generated by the swept trailing edges.

Northam, G. B.↗
NASA NTRS1991

Passive microwave remote sensing of soil moisture: Results from HAPEX, FIFE, and MONSOON 90

HAPEX (Hydrologic Atmospheric Pilot Experiment), FIFE (First ISLSCP Field Experiment) and MONSOON 90 which used an imaging microwave radiometer operating at a frequency of 1.42 GHz are reported. For FIFE and MONSOON 90, a wide range of moisture conditions were present and it was possible to observe the drydown of the soil following heavy rain and to map its spatial variation. The quantitive agreement of microwave observations and ground measurements was very good. In HAPEX there were no significant rains and conditions were generally rather dry, however, moisture variations due to irrigation were observed.

Schmugge, Thomas↗
NASA NTRS1992

Passive microwave remote sensing of soil moisture - Results from HAPEX, FIFE and MONSOON 90

HAPEX (Hydrologic Atmospheric Pilot Experiment), FIFE (First ISLSCP Field Experiment) and MONSOON 90 which used an imaging microwave radiometer operating at a frequency of 1.42 GHz are reported. For FIFE and MONSOON 90, a wide range of moisture conditions were present and it was possible to observe the drydown of the soil following heavy rain and to map its spatial variation. The quantitative agreement of microwave observations and ground measurements was very good. In HAPEX there were no significant rains and conditions were generally rather dry, however, moisture variations due to irrigation were observed.

Schmugge, T.↗
NASA NTRS1992

Single element injector testing for STME injector technology

An oxidizer-swirled coaxial element injector is being developed for application in the liquid oxygen/gaseous hydrogen Space Transportation Main Engine (STME) for the National Launch System (NLS) vehicle. This paper reports on the first two parts of a four part single injector element study for optimization of the STME injector design. Measurements of Rupe mixing efficiency and atomization characteristics are reported for single element versions of injection elements from two multielement injectors that have been recently hot fire tested. Rather than attempting to measure a definitive mixing efficiency or droplet size parameters of these injector elements, the purpose of these experiments was to provide a baseline comparison for evaluating future injector element design modifications. Hence, all the experiments reported here were conducted with cold flow simulants to nonflowing, ambient conditions. Mixing experiments were conducted with liquid/liquid simulants to provide economical trend data. Atomization experiments were conducted with liquid/gas simulants without backpressure. The results, despite significant differences from hot fire conditions, were found to relate to mixing and atomization parameters deduced from the hot fire testing, suggesting that these experiments are valid for trend analyses. Single element and subscale multielement hot fire testing will verify optimized designs before committing to fullscale fabrication.

Hulka, J.↗
NASA NTRS1993

Model for the formation of silicon carbide from the pyrolysis of dichlorodimethylsilane in hydrogen. I - Silicon formation from chlorosilanes. II - Silicon carbide formation from silicon and methane

In the first part of this work, a model is developed for the deposition of silicon from the reduction of silicon tetrachloride with hydrogen in a tubular reactor at 700-1100 C, at atmospheric pressure. The model is based on gas chromatography of the volatile products of the reaction, followed by gravimetric analysis of total Si deposition on the tube. In the second part of this work, a model is developed for the case of SiC deposition from the pyrolysis of dichlorodimethylsilane in hydrogen under the same reactor conditions. The rate constants derived from a nonlinear regression analysis are reported.

Cagliostro, Domenick E.↗
NASA NTRS1993

OH-radical imaging and velocity field measurements in a gaseous hydrogen/oxygen rocket

Detailed measurements of the OH-radical and velocity fields for a shear coaxial unielement rocket chamber burning gaseous hydrogen and gaseous oxygen propellants are reported. The velocity measurements indicate that a highly unsteady flowfield results from the turbulent combustion of the coaxial jets. The core of the oxygen stream is observed to remain intact well downstream of the injector face while the maximum turbulent intensities in the shear layer region between the hydrogen and oxygen flows were measured to be about 25 percent. Both 1D and 2D laser-induced fluorescence studies of the OH-radical are reported and provide information on the evolving flame structure under rocketlike conditions. Both single and multiple laser pulse images indicate that the structure of the unsteady flowfield is directly reflected in the combustion zone flame structure. Preliminary results regarding analysis approaches and interpretation of the data are also presented.

Moser, M. D.↗
NASA NTRS1993

Simulation of preburner sprays, volume 1

Under the present contract a study was made on the characteristics of the sprays of coaxial injectors with particular emphasis on those aspects relevant to the performance of rocket engines. The technical effort was performed primarily by Imperial College of Science and Technology and the details of this effort are contained in the accompanying technical report by Hardalupas and Whitelaw, which forms Vol. 2 of the report. The role of Scientific Research Associates was review of material, initial direction of the technical effort and review of all reports. The study considered characteristics of sprays under a variety of conditions. Control of these sprays is important as the spray details can control both rocket combustion stability and efficiency. Imperial College considered the following: first, measurement of the size and rate of spread of the sprays produced by single coaxial airblast nozzles with axial gaseous stream. The local size, velocity and flux characteristics for a wide range of gas and liquid flowrates were measured and the results were correlated with the conditions of the spray at the nozzle exit. Second, examination of the effect of the geometry of single coaxial airblast atomizers on spray characteristics. The gas and liquid tube diameters were varied over a range of values, the liquid tube recess was varied and the shape of the exit of the gaseous jet was varied from straight to converging. Third, quantification of the effect of swirl in the gaseous stream on the spray characteristics produced by single coaxial airblast nozzles. Fourth, quantification of the effect of reatomization by impingement of the spray on a flat disc positioned around 200 mm from the nozzle exit. This models spray impingement on the turbopump dome during the startup process of the preburner of the Space Shuttle Main Engine (SSME). Fifth, study of the interaction between multiple sprays without and with swirl in their gaseous stream. The spray characteristics of single nozzles were compared with that of three identical nozzles with their axis at a small distance from each other. This study simulates the sprays in the preburner of the SSME, where there are around 260 elements on the faceplate of the combustion chamber. And lastly, design an experimental facility to study the characteristics of sprays at high pressure conditions and at supercritical pressure and temperature for the gas but supercritical pressure and subcritical temperature for the liquid.

Source record↗
NASA NTRS1996

Further evaluation of traditional icing scaling methods

This report provides additional evaluations of two methods to scale icing test conditions; it also describes a hybrid technique for use when scaled conditions are outside the operating envelope of the test facility. The first evaluation is of the Olsen method which can be used to scale the liquid-water content in icing tests, and the second is the AEDC (Ruff) method which is used when the test model is less than full size. Equations for both scaling methods are presented in the paper, and the methods were evaluated by performing icing tests in the NASA Lewis Icing Research Tunnel (IRT). The Olsen method was tested using 53 cm diameter NACA 0012 airfoils. Tests covered liquid-water-contents which varied by as much as a factor of 1.8. The Olsen method was generally effective in giving scale ice shapes which matched the reference shapes for these tests. The AEDC method was tested with NACA 0012 airfoils with chords from 18 cm to 53 cm. The 53 cm chord airfoils were used in reference tests, and 1/2 and 1/3 scale tests were made at conditions determined by applying the AEDC scaling method. The scale and reference airspeeds were matched in these tests. The AEDC method was found to provide fairly effective scaling for 1/2 size tests, but for 1/3 size models, scaling was generally less effective. In addition to these two scaling methods, a hybrid approach was also tested in which the Olsen method was used to adjust the LWC after size was scaled using the constant Weber number method. This approach was found to be an effective way to test when scaled conditions would otherwise be outside the capability of the test facility.

Anderson, David N.↗
NASA NTRS1997

Heat Treatments of ZnSe Starting Materials for Physical Vapor Transport

The effect of different heat treatments on stoichiometry and residual gas pressure in ZnSe physical vapor transport system was investigated. The dependence of the amount and composition of the residual gas on various heat treatment procedures is reported. Heat treatment of ZnSe starting materials by baking under the condition of dynamic vacuum to adjust its stoichiometry was performed and the effectiveness of the treatment was confirmed by the measurements of the partial pressure of Se2, P(sub Se2), in equilibrium with the heat treated samples. Optimum heat treatment procedures on the ZnSe starting material for the physical vapor transport process are discussed and verified experimentally.

Su, Ching-Hua↗