Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Compressor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Laser Doppler velocimeter measurement in the tip region of a compressor rotor

The axial and tangential velocity components near the tip region of a compressor rotor were measured by a laser Doppler velocimeter. The measurements were taken at 25 radial locations in the outer twenty percent of the blade span and at 10 axial locations upstream, inside and at the exit of the rotor. The results are interpreted to derive the behavior of the leakage flow, annulus wall boundary layer growth, inviscid effects and the rotor wake decay characteristics in the tip region. The inviscid and annulus wall boundary layer effects dominate up to quarter chord, beyond which the leakage phenomena has a major influence in altering the flow characteristics in the outer ten percent of the blade span. The annulus wall boundary layer undergoes drastic change through the passage. The velocity field measured near the leading edge reveals the effects of rapid acceleration near the suction surface and the stagnation point on the pressure surface.

Murthy, K. N. S.↗

Inlet boundary layer effects in an axial compressor rotor. I - Blade-to-blade effects

This paper discusses experimental data measured on the blading and downstream of an isolated compressor rotor with thick inlet endwall boundary layers. The objective of the study was to compare these results with data acquired previously with thin inlet boundary layers and to assess the impact of inlet boundary layer thickness on the secondary flow. Flow visualization results showed the powerful impact of the hub corner stall and how at the same near stall flow coefficient where with thin inlet boundary layers the blade was separated at midspan, with thick inlet boundary layers it was attached. It was also shown that while secondary flow was very weak, it did produce sufficient radial redistribution to cause an apparent negative loss at the blade root.

Wagner, J. H.↗

Inlet boundary layer effects in an axial compressor rotor. II - Throughflow effects

This paper presents results of an experimental aerodynamic study conducted in the rotating frame of reference downstream of an isolated compressor rotor with both thick and thin inlet endwall boundary layers. The paper focuses on those aspects of the data having particular significance to the assumptions and application of throughflow theory. These aspects include the spanwise distributions of static pressure and blockage, and the radial redistribution of fluid as it passes through the blade row. It is demonstrated that the main contributions to total pressure loss, blockage, and the distortion of the static pressure field were due to the hub corner stall and tip leakage. This is a significant departure from previous conclusions which looked to the endwall boundary layer and to secondary flow as major loss and blockage producing mechanisms.

Wagner, J. H.↗

An experimental study of the compressor rotor blade boundary layer

The three-dimensional turbulent boundary layer developing on a rotor blade of an axial flow compressor was measured using a miniature 'x' configuration hot-wire probe. The measurements were carried out at nine radial locations on both surfaces of the blade at various chordwise locations. The data derived includes streamwise and radial mean velocities and turbulence intensities. The validity of conventional velocity profiles such as the 'power law profile' for the streamwise profile, and Mager and Eichelbrenner's for the radial profile, is examined. A modification to Mager's crossflow profile is proposed. Away from the blade tip, the streamwise component of the blade boundary layer seems to be mainly influenced by the streamwise pressure gradient. Near the tip of the blade, the behavior of the blade boundary layer is affected by the tip leakage flow and the annulus wall boundary layer. The 'tangential blockage' due to the blade boundary layer is derived from the data. The profile losses are found to be less than that of an equivalent cascade, except in the tip region of the blade.

Pouagare, M.↗

Energy efficient engine. High pressure compressor detail design report

A compressor optimization study defined a 10-stage configuration with a 22.6:1 pressure ratio, and adiabatic efficiency goal of 86.1%, and a polytropic efficiency of 90.6%; the corrected airflow is 53.5 kg/sec. Subsequent component testing included three full-scale tests: a six-stage rig test, and another 10-stage rig test completed in the second quarter of 1982. Information from these tests is being used to select the configuration for a core engine test scheduled for July 1982 and an integrated core/low spool test slated for early 1983. The test results will also provide data base for the flight propulsion system.

Holloway, P. R.↗

Magentically actuated compressor

A vibration free fluid compressor particularly adapted for Stirling cycle cryogenic refrigeration apparatus comprises a pair of identical opposing ferromagnetic pistons located in a housing and between a gas spring including a sealed volume of a working fluid such as gas under pressure. The gas compresses and expands in accordance with movement of the pistons to generate a compression wave which can be vented to other apparatus, for example, a displacer unit in a Stirling cycle engine. The pistons are urged outwardly due to the pressure of the gas; however, a fixed electromagnetic coil assembly located in the housing adjacent the pistons, is periodically energized to produce a magnetic field which interlinks the pistons in such a fashion that the pistons are mutually attracted to one another. The mass of the pistons, in conjunction with the compressed gas between them, form a naturally resonant system which, when the pistons are electromagnetically energized, produces an oscillating compression wave in the entrapped fluid medium.

Evans, J.↗

Airflow calibration of a bellmouth inlet for measurement of compressor airflow in turbine-powered propulsion simulators

The development of turbine-powered propulsion simulators for high-speed wind tunnel models requires a bellmouth inlet which can accurately measure compressor-inlet airflow. A bellmouth inlet was instrumented with total pressure probes, static pressure probes, and thermocouples for airflow measurement. The bellmouth flowmeter against a critical venturi flowmeter was calibrated. The calibration was done at four inlet pressures ranging from 58 to 114 kPa. The bellmouth discharge coefficient varied as a function of bellmouth-throat Mach number. Over the range of Reynolds number and Mach number tested the Reynolds number was not a significant influence on the discharge coefficient. The overall accuracy of the bellmouth inlet as a flowmeter was estimated to be + or - 0.5% of the flowmeter reading.

Smith, S. C.↗

Comparison of calculated and experimental cascade performance for controlled-diffusion compressor stator blading

The mid-span section of a previously reported controlled-diffusion compressor stator has been experimentally evaluated in cascade. Measurements are taken over a range of incidence angles for blade chord Reynolds numbers from 470,000 to 690,000. Blade chord length is 12.7 cm, aspect ratio is 2.0, and solidity is 1.67. Measurements include conventional cascade performance parameters as well as blade surface pressures. Computations are made for the inviscid flow field, surface boundary layers, and loss for several of the blade inlet angle conditions, are compared against corresponding data.

Sanger, N. L.↗

Extended parametric representation of compressor fans and turbines. Volume 2: Part user's manual (parametric turbine)

A turbine modeling technique has been developed which will enable the user to obtain consistent and rapid off-design performance from design point input. This technique is applicable to both axial and radial flow turbine with flow sizes ranging from about one pound per second to several hundred pounds per second. The axial flow turbines may or may not include variable geometry in the first stage nozzle. A user-specified option will also permit the calculation of design point cooling flow levels and corresponding changes in efficiency for the axial flow turbines. The modeling technique has been incorporated into a time-sharing program in order to facilitate its use. Because this report contains a description of the input output data, values of typical inputs, and example cases, it is suitable as a user's manual. This report is the second of a three volume set. The titles of the three volumes are as follows: (1) Volume 1 CMGEN USER's Manual (Parametric Compressor Generator); (2) Volume 2 PART USER's Manual (Parametric Turbine); (3) Volume 3 MODFAN USER's Manual (Parametric Modulation Flow Fan).

Coverse, G. L.↗

CO2 compressor vibration and cause analysis

The operational experience of a large turbine drive carbon dioxide compressor train in a urea plant with capacity of 1620 tons/day is considered. After the initial start-up in 1976, the vibration in the HP cylinder was comparatively serious. The radial vibration reached 4.2 to 4.5 mils and fluctuated around this value. It was attributed to the rotating stall based on the spectrum analysis. Additional return line from the 4th to 4th and higher temperature of the 4th inlet has cured the vibration. Problems are described which were encountered in the operation along with their solutions, and/or improvements.

Ying, Y. L.↗

End-wall and profile losses in a low-speed axial flow compressor rotor

The blade-to-blade variation of relative stagnation pressure losses in the tip region inside the rotor of a single-stage, axial-flow compressor, is presented and interpreted in this paper. The losses are measured at two flow coefficients (one at the design point and the other at the near peak pressure rise point) to discern the effect of blade loading on the end-wall losses. The tip clearance losses are found to increase with an increase in the pressure rise coefficient. The losses away from the tip region and near the hub regions are measured downstream. The losses are integrated and interpreted in this paper.

Lakshminarayana, B.↗

Modeling the 3-D flow effects on deviation angle for axial compressor middle stages

A model of the spanwise variation of the three-dimensional flow effects on deviation is proposed for middle-stage rotors and stators. This variation is taken as the difference above or below that predicted by blade element theory at any spanwise location. It was found that the stator variation is strongly affected by the end-wall boundary-layer thickness as well as camber, solidity, and blade channel aspect ratio. Rotor variation was found to depend on end-wall boundary layer thickness and tip clearance normalized by blade span. If these parameters are known or can be calculated, the models provide a reasonable approximation to the spanwise variation of deviation for middle compressor stages operating at low to high subsonic inlet Mach numbers.

Roberts, W. B.↗

Active suppression of compressor instabilities

A strategy is proposed for controlling aerodynamic instabilities which limit the useful range of both axial and centrifugal turbomachines. Both local and global instabilities (incipient rotating stall and surge) are analyzed. A theory is developed which shows how an additional disturbance, driven from real time data measured within the machine, can be generated so as to realize a device with characteristics fundamentally different from those of the turbomachine without control; for the particular compressor analyzed, the control led to a 20 percent increase in the extent of the stable operating range. The use of structural dynamics to enhance stability is also discussed.

Epstein, A. H.↗

The measurement of boundary layers on a compressor blade in cascade at high positive incidence angle. 1: Experimental techniques and results

Measurements of the mean velocity and turbulence intensity were made using a one-component laser Doppler velocimeter in the boundary layer and near wake about a double circular arc, compressor blade in cascade. The measurements were made at a chord Reynolds number of 500,000. Boundary layer measurements on the pressure surface indicate a transition region over the last 40% of the chord. A small separation bubble near the leading edge of the suction surface results in an immediate transition from laminar to turbulent flow. The non-equilibrium turbulent boundary layer separates near the trailing edge of the suction surface. Similarity of the outer region of the turbulent boundary layer ceases to exist in the separated region. Also, similarity does not hold in the near-wake region, a region which includes negative mean velocities because of the separation near the trailing edge on the suction surface.

Deutsch, S.↗

The measurement of boundary layers on a compressor blade in cascade at high positive incidence angle. 2: Data report

Boundary layer and near-wake velocity measurements have been made in the well documented flow field about a double circular arc compressor blade in cascade, at an incidence angle of 5 deg. and a chord Reynolds number of 500,000. In Part 2 of this report these measurements were analyzed and presented in standard graphical format. The flow geometry, measurement techniques, and physics of the flow field were also discussed. In this, part 2 of the report, raw and analyzed data are presented in tabulated form in an attempt to make this data more accessible to computational comparison. Also included in part 2 is a description of the data analysis employed. A computer tape containing the data is available.

Deutsch, S.↗

Design of 9.271-pressure-ratio 5-stage core compressor and overall performance for first 3 stages

Overall aerodynamic design information is given for all five stages of an axial flow core compressor (74A) having a 9.271 pressure ratio and 29.710 kg/sec flow. For the inlet stage group (first three stages), detailed blade element design information and experimental overall performance are given. At rotor 1 inlet tip speed was 430.291 m/sec, and hub to tip radius ratio was 0.488. A low number of blades per row was achieved by the use of low-aspect-ratio blading of moderate solidity. The high reaction stages have about equal energy addition. Radial energy varied to give constant total pressure at the rotor exit. The blade element profile and shock losses and the incidence and deviation angles were based on relevant experimental data. Blade shapes are mostly double circular arc. Analysis by a three-dimensional Euler code verified the experimentally measured high flow at design speed and IGV-stator setting angles. An optimization code gave an optimal IGV-stator reset schedule for higher measured efficiency at all speeds.

Steinke, Ronald J.↗

The T55-L-712 turbine engine compressor housing refurbishment project

A study was conducted to access the feasibility of reclaiming T55-L-712 turbine engine compressor housings with an 88 wt % aluminum -- 12 wt % silicon alloy applied by the plasma spray processes. Tensile strength testing was conducted on as-sprayed and thermally cycled test specimens which were plasma sprayed from 0.020 to 0.100 in. Satisfactory tensile strength valves were observed in the as-sprayed tensile specimens. There was essentially no decrease in tensile strength after thermally cycling the tensile specimens.

Leissler, George W.↗

Materials for Advanced Turbine Engines (MATE). Project 4: Erosion resistant compressor airfoil coating

The ability of coatings to provide at least a 2X improvement in particulate erosion resistance for steel, nickel and titanium compressor airfoils was identified and demonstrated. Coating materials evaluated included plasma sprayed cobalt tungsten carbide, nickel carbide and diffusion applied chromium plus boron. Several processing parameters for plasma spray processing and diffusion coating were evaluated to identify coating systems having the most potential for providing airfoil erosion resistance. Based on laboratory results and analytical evaluations, selected coating systems were applied to gas turbine blades and evaluated for surface finish, burner rig erosion resistance and effect on high cycle fatigue strength. Based on these tests, the following coatings were recommended for engine testing: Gator-Gard plasma spray 88WC-12Co on titanium alloy airfoils, plasma spray 83WC-17Co on steel and nickel alloy airfoils, and Cr+B on nickel alloy airfoils.

Rashid, J. M.↗