Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Characterizations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Lubricity of well-characterized jet and broad-cut fuels by ball-on-cylinder machine

A ball-on-cylinder machine (BOCM) was used to measure the lubricity of fuels. The fuels tested were well-characterized fuels available from other programs at the NASA Lewis Research Center plus some in-house mildly hydroprocessed shale fuels from other programs included Jet-A, ERBS fuel, ERBS blends, and blend stock. The BOCM tests were made before and after clay treatment of some of these fuels with both humidified air and dry nitrogen as the preconditioning and cover gas. As expected, clay treatment always reduced fuel lubricity. Using nitrogen preconditioning and cover gas always resulted in a smaller wear scar diameter than when humidified air was used. Also observed was an indication of lower lubricity with lower boiling range fuels and lower aromatic fuels. Gas chromatographic analysis indicted changes in BOCM-stressed fuels.

Prok, G. M.↗
NASA NTRS1984

Characterizing Delamination Resistance of Toughened Resin Composites

The delamination resistance of toughened resin composites was studied. Both the edge delamination test (EDT) and the double-cantilever-beam (DCB) test provided a useful ranking of improvements in delamination resistance between brittle and tough resin composites. Several layups were designed for the edge delamination test to cover a wide range of mixed-mode conditions. The DCB and the various layups of the EDT were then used to characterize the interlaminar fracture behavior of brittle and toughened resin composites subjected to both static and cyclic loading.

Obrien, T. K.↗
NASA NTRS1984

LANDSAT instruments characterization

Several studies were performed using LANDSAT-4 and -5 simultaneous overpath data 40608-15472 and 50014-15465 over Pensacola, FL. The overlap region of these two scenes was determined visually on the IAT and then sampled into 32 x 32 segments. The mean and standard deviation (SD) for each segment were calculated. In general, the plots of the means of LANDSAT-4 versus LANDSAT-5 lie on the diagonal line. Some of the data lie out of the diagonal line, which indicates a possible bidirectional observation effect occurs. In addition to editing the five FCL files on CALDUMP tapes into seven 1000 minor frame (MF). CAL files, program LEE.FOR was modified to use information from start of shutter obscuration extracted from program START.FOR to create seven 200 MF.CAL files that can be run through the current TRAPP program for TM sensor characterization. The location of start of shutter obscuration was determined for both LANDSAT-4 and -5.

Lee, Y.↗
NASA NTRS1984

LANDSAT instruments characterization

Work performed for the LANDSAT instrument characterization task in the areas of absolute radiometry, coherent noise analysis, and between-date smoothing is reported. Absolute radiometric calibration for LANDSAT-5 TM under ambient conditions was performed. The TM Radiometric Algorithms and Performance Program (TRAPP) was modified to create optional midscan data files and to match the TM Image Processing System (TIPS) algorithm for pulse determination. Several data reduction programs were developed, including a linear regression and its plotted result. A fast Fourier transformation study was conducted on the resequenced TM data. Subscenes of homogeneous water within scenes over Pensacola, Florida were used for testing the FFT on the resequenced data. Finally, a gain and pulse height stability study of LANDSAT 5 TM spectral bands was performed.

Lee, Y.↗
NASA NTRS1984

Characterizing the scientific potential of satellite sensors

Algorithms and software were developed for the correction of coherent noise, scan correlated shift, and the bright target saturation effect in Thematic Mapper imagery. In addition, a package of LANDSAT Assessment System programs was developed to demonstrate the results from TM radiometric characterization and calibration work.

Lee, Y.↗
NASA NTRS1984

Characterization of MMIC devices for active array antennas

Certain aspects of monolithic microwave integrated circuit (MMIC) interconnectivity were investigated. Considerations that lead to preserving the inherently reproducible characteristics of the MMIC are proposed. It is shown that at radio frequencies (RF) greater than 20 GHz, the transition from the MMIC device to other transmission media must be an accurate RF match. It is proposed that the RF match is sufficiently critical to include the transition as part of the delivered MMIC package. The model to analyze several transitions is presented. This model consists of a succession of abrupt discontinuities in printed circuit transmission lines. The analysis of these discontinuities is achieved by the Spectral Galerkin technique, to establish the modes and mode matching, to generate the generalized S parameters of the individual discontinuities. Preliminary results achieved with this method are presented. It is concluded that special effects should be coordinated by the active array antenna industry toward standardization of MMIC packaging and characterization.

Smetana, J.↗
NASA NTRS1984

Characterizing the scientific potential of satellite sensors

Eleven thematic mapper (TM) radiometric calibration programs were tested and evaluated in support of the task to characterize the potential of LANDSAT TM digital imagery for scientific investigations in the Earth sciences and terrestrial physics. Three software errors related to integer overflow, divide by zero, and nonexist file group were found and solved. Raw, calibrated, and corrected image groups that were created and stored on the Barker2 disk are enumerated. Black and white pixel print files were created for various subscenes of a San Francisco scene (ID 40392-18152). The development of linear regression software is discussed. The output of the software and its function are described. Future work in TM radiometric calibration, image processing, and software development is outlined.

Source record↗
NASA NTRS1984

Characterizing the scientific potential of satellite sensors

Analytical and programming support is to be provided to characterize the potential of the LANDSAT thematic mapper (TM) digital imagery for scientific investigations in the Earth sciences and in terrestrial physics. In addition, technical support to define lower atmospheric and terrestrial surface experiments for the space station and technical support to the Research Optical Sensor (ROS) study scientist for advanced studies in remote sensing are to be provided. Eleven radiometric calibration and correction programs are described. Coherent noise and bright target saturation correction are discussed along with image processing on the LAS/VAX and Hp-300/IDIMS. An image of San Francisco, California from TM band 2 is presented.

Source record↗
NASA NTRS1985

Characterization of mode 1 and mixed-mode failure of adhesive bonds between composite adherends

A combined experimental and analytical investigation of an adhesively bonded composite joint was conducted to characterize both the static and fatigue beyond growth mechanism under mode 1 and mixed-mode 1 and 2 loadings. Two bonded systems were studied: graphite/epoxy adherends bonded with EC 3445 and FM-300 adhesives. For each bonded system, two specimen types were tested: a double-cantilever-beam specimen for mode 1 loading and a cracked-lapshear specimen for mixed-mode 1 and 2 loading. In all specimens tested, failure occurred in the form of debond growth. Debonding always occurred in a cohesive manner with EC 3445 adhesive. The FM-300 adhesive debonded in a cohesive manner under mixed-mode 1 and 2 loading, but in a cohesive, adhesive, or combined cohesive and adhesive manner under mode 1 loading. Total strain-energy release rate appeared to be the driving parameter for debond growth under static and fatigue loadings.

Mall, S.↗
NASA NTRS1985

Accelerated viscoelastic characterization of T300-5208 graphite-epoxy laminates

A viscoelastic response scheme for the accelerated characterization of polymer-based composite laminates in applied to T300/5208 graphite/epoxy. The response of uni-directional specimens is modeled. The transient component of the viscoelastic creep compliance is assumed to follow a power law approximation. A recursive relationship is developed, based upon the Schapery single-integral equation, which allows approximation of a continuous time-varying uniaxial load using discrete steps in stress. The viscoelastic response of T300/5208 to transverse normal and shear stresses is determined unsing 90 deg and 10 deg off-axis tensile specimens. In each case the seven viscoelastic material parameters required in the analysis are determined experimentally using short-term creep and creep recovery tests. It is shown that an accurate measure of the power law exponent is crucial for accurate long-term prediction. A short term test cycle selection procedure is proposed, which should provide useful guidelines for the evaluation of other viscoelastic materials.

Tuttle, M. E.↗
NASA NTRS1985

Thermal Band Characterization of the LANDSAT-4 Thematic Mapper

The initial characterization of the Thematic Mapper (TM) thermal band is reported including gain stability, gain relation to internal calibration, corrections for channel-to-channel and scan direction differences, an approximate comparison to ground truth, and a calculation of noise equivalent temperature difference. Updated calibration information is also presented.

Lansing, J. C.↗
NASA NTRS1985

Silicon carbide-silicon nitride fibers: Preparation and characterization of polycarbosilazane precursors

This study examines the effect of modifications of the chemical structure of the monomers on the properties of the polymeric precursor and and ceramic fibers. A group of silaneamines, R'-Si (NH-R) sub 3, taken from the series where R' is methyl or phenyl and R is n-propyl, n-butyl, phenyl or allyl, are converted to polycarbosilazanes by heating in excess of 500 C. Resins obtained from this polymerization are characterized by NMR and IR spectroscopy and GPC. Each resin is tested for fiber-forming properties. Resin samples and fibers are hydrolytically cured. Thermogravimetric analyses are conducted on the cured resins to compare the relative thermal stability and examine the pyrolysis process. Cured fibers are tested for tensil strength.

Crouse, D. J.↗
NASA NTRS1985

Characterization of material surfaces exposed to atomic oxygen on space shuttle missions

Material samples prepared for exposure to ambient atomic oxygen encountered during space shuttle flights in low Earth orbit were characterized by the experimental techniques of ELLIPSOMETRY, ESCA, PIXE, and RBS. The first group of samples, which were exposed during the STS-8 mission, exhibited some very interesting results. The second group of samples, which are to be exposed during the upcoming STS-17 mission, have been especially prepared to yield quantitative information on the optical changes, oxygen solution, and surface layer formation on metal films of silver, gold, nickel, chromium, aluminum, platinum, and palladium evaporated onto optically polished silicon wafers.

Fromhold, A. T.↗
NASA NTRS1985

Characterization of LANDSAT-4 TM and MSS Image Quality for the Interpretation of California's Agricultural Resources

The quality of LANDSAT-4 MSS and TM data was determined by analyzing TM spectral and spatial performance in terms of spectral variability of natural targets and the TM-ground instantaneous field-of-view (IFOV) variability in level and mountainous terrain; and by assessing the suitability of TM and MSS image products for characterizing renewable resourse features. The TM data should be extremelly valuable for crop type and area proportion estimation; undating agricultural land use survey maps at 1:24,000 scale and smaller, field boundary definition; and determining the size and location of individual farmsteads. Ongoing research activities are focused on making spectral and spatial analyses of both MSS and TM analytical film products. The improved spectral, spatial, and radiometric quality of the TM data, should promote a renewed emphasis and interest in direct visual interpretation of these image products, both for updating and improving land stratification in support of resource inventory and for enhancing the image analyst's contribution to computer-assisted analysis procedures.

Degloria, S. D.↗
NASA NTRS1985

Ignition characterization of LOX/hydrocarbon propellants

The results of an evaluation of the ignition characteristics of the gaseous oxygen (Gox)/Ethanol propellant combination are presented. Ignition characterization was accomplished through the analysis, design, fabrication and testing of a spark initiated torch igniter and prototype 620 lbF thruster/igniter assembly. The igniter was tested over a chamber pressure range of 74 to 197 psia and mixture ratio range of 0.778 to 3.29. Cold (-92 to -165 F) and ambient (44 to 80 F) propellant temperatures were used. Spark igniter ignition limits and thruster steady state and pulse mode, performance, cooling and stability data are presented. Spark igniter ignition limits are presented in terms of cold flow pressure, ignition chamber diameter and mixture ratio. Thruster performance is presented in terms of vacuum specific impulse versus engine mixture ratio. Gox/Ethanol propellants were shown to be ignitable over a wide range of mixture ratios. Cold propellants were shown to have a minor effect on igniter ignition limits. Thruster pulse mode capability was demonstrated with multiple pulses of 0.08 sec duration and less.

Lawver, B. R.↗
NASA NTRS1985

Ignition characterization of LOX/hydrocarbon propellants

The results of an evaluation of the ignition characteristics of the gaseous oxygen (Gox)/Ethanol propellant combination are summarized. Ignition characterization was accomplished through the analysis, fabrication and testing of a spark initiated torch igniter and prototype 620 1bF thruster/igniter assembly. The igniter was tested over a chamber pressure range of 3.3 to 262 psia and a mixture ratio range of 0.4 to 40. The prototype thruster/igniter assembly was tested over the chamber pressure range of 74 to 197 psia and mixture ratio range of 0.778 to 3.29. Cold (-92 to -165 F) and ambient (44 to 80 F) propellant temperatures were used. Spark igniter ignition limits and thruster steady state and pulse mode, performance, cooling and stability data are presented. Spark igniter ignition limits are presented in terms of cold flow pressure, ignition chamber diameter and mixture ratio. Thruster performance is presented in terms of vacuum specific impulse versus engine mixture ratio. Gox/Ethanol propellants were shown to be ignitable over a wide range of mixture ratios. Cold propellants were shown to have a minor effect on igniter ignition limits. Thruster pulse mode capability was demonstrated with multiple pulses of 0.08 sec duration and less.

Lawver, B. R.↗
NASA NTRS1985

Synthesis and Characterization of Copolyimides with Varying Flexibilizing Groups

A series of polyimides and copolyimides with varying flexibilizing groups in their backbone were prepared. They were characterized in order to evaluate the effect of these groups on their rheological, mechanical, adhesive, and thermal properties. A copolymer with equimolar amounts of m-PDA and 4,4'-ODA exhibited the lowest viscosity at all strain rates studied. Since this particular polymer exhibited the best flow properties, it was also evaluated as an adhesive and was found to have exceptional characteristics for this application.

Burks, H. D.↗
NASA NTRS1985

Enrichments for phototrophic bacteria and characterization by morphology and pigment analysis

The purpose of this investigation was to examine several sulfide containing environments for the presence of phototrophic bacteria and to obtain enriched cultures of some of the bacteria present. The field sites were Alum Rock State Park, the Palo Alto salt marsh, the bay area salt ponds, and Big Soda Lake (near Fallon, Nevada). Bacteria from these sites were characterized by microscopic examination, measurement of in vitro absorption spectra, and analysis of carotenoid pigments. Field observations at one of the bay area salt ponds, in which the salt concentration was saturating (about 30 percent NaCl) and the sediments along the shore of the pond covered with a gypsum crust, revealed a layer of purple photosynthetic bacteria under a green layer in the gypsum crust. Samples of this gypsum crust were taken to the laboratory to measure light transmission through the crust and to try to identify the purple photosynthetic bacteria present in this extremely saline environment.

Brune, D.↗