Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CONE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

Experimental wake survey behind a 140 deg-included-angle cone at angles of attack of 0 deg and 5 deg, Mach numbers from 1.60 to 3.95, and longitudinal stations varying from 1.0 to 8.39 body diameters

The flow properties in the wake of a 140 deg-included-angle cone at Mach numbers from 1.60 to 3.95 and at angles of attack of 0 deg and 5 deg are discussed. The wake flow properties are calculated from total and static pressures measured with a pressure rake at longitudinal stations varying from 1.0 to 8.39 body diameters and at lateral stations varying from -0.42 to 3.0 body diameters. These measurements show a consistent trend throughout the range of Mach number and longitudinal distance and an increase in dynamic pressure with increasing longitudinal station.

Brown, C. A., Jr.↗
NASA NTRS1971

A study of boundary layer transition on outgassing cones in hypersonic flow

Surface heat-transfer rates and pressures were measured at hypersonic speeds on sharp cones at zero angle of attack with and without gas injection. Using the non-injection results for reference data the effects on heating and transition location of surface roughness and injectant rate, distribution and composition were determined. The transition location was sensitive to the injectant distribution. The transition Reynolds numbers were significantly greater when the injectant distribution was constant than with a variable distribution. The measured heat-transfer distribution were also strongly dependent upon the injectant distribution. Transition Reynolds number results obtained during this program with a variable injectant distribution were correlated with a limited amount of data available for a degrading model tested in a different facility. Transitional data with constant injectant distribution were correlated with earlier results. An empirical correlation of heat-transfer reduction due to gas injection in turbulent flow was developed for both distributions tested. Several effects of mass addition on heating and transition, which have been earlier reported, were observed.

Stalmach, C. J., Jr.↗
NASA NTRS1972

Subsonic and supersonic static aerodynamic characteristics of a family of bulbous base cones measured with a magnetic suspension and balance system

Results of subsonic and supersonic wind-tunnel tests with a magnetic balance and suspension system on a family of bulbous based cone configurations are presented. At subsonic speeds the base flow and separation characteristics of these configurations is shown to have a pronounced effect on the static data. Results obtained with the presence of a dummy sting are compared with support interference free data. Support interference is shown to have a substantial effect on the measured aerodynamic coefficient.

Vlajinac, M.↗
NASA NTRS1972

Space shuttle: Aerodynamic characteristics of cone-cylinder-flare-fin configurations at Mach numbers of 1.96, 2.74, and 4.96 and angles of attack from 50 to 90 degrees

A 0.00227-scale parametric model of an LMSC/MSFC water recoverable booster was tested in the MSFC 14 x 14-inch trisonic wind tunnel. The purpose of the test was to obtain high angle of attack force and static stability data which could be used by MSFC in preliminary design and aerodynamic trade studies. These data were obtained using six-component internal strain gauge balances. One hundred forty-four different geometrical combinations were possible as all model parts were interchangeable (three nose cones, three cylinder lengths, four flare sections and three sets of fins, plus a no-fin case in combination with the other components). However, due to tunnel occupancy limitations, only the most representative combinations were tested. All configurations investigated were tested at Mach 1.96, 2.74 and 4.96 with data obtained at angles of attack from 50 degrees to 90 degrees and at angles of sideslip from -10 degrees to +10 degrees (at an angle of attack of 60 degrees).

Bradley, D.↗
NASA NTRS1971

Layered 'recognition cone' networks that pre-process, classify, and describe.

A sequence of six types of pattern recognition system is examined. A program is described to illustrate some of the features developed. The first type (similar to many of the programs currently used) preprocesses by applying layers of local averaging and differencing transforms to smooth, fill in gaps and heighten contours, curves, and angles. It then applies a set of characterizers, each of which implies a set of names. The program chooses the single most high implied name. The second type combines the preprocessing transforms and the characterizers into a single operation of general type. Transforms build up a next representation of the input, while the characterizers imply the output name. The third type erases the distinction between a transform and an implication. Now all outputs are stored in the next transform layer. As the program averages information, its layers shrink, so that the system builds a cone of layers. When the program reaches the apex (a layer of only one cell that contains all the information), it chooses the single name with which it classifies the input. The fourth type is capable of choosing more than one name and, therefore, can both describe and classify the scene. The fifth type examines the interrelations among the set of names chosen. The sixth step can be taken to converse about the scene, developing an appropriate description in response to suggestions and queries. This allows the program to perform more computations and to look again on demand.

Uhr, L.↗
NASA NTRS1972

Effect of thermally expanding surfaces on aerodynamic roll torques for cones.

An experimental and analytical study has been made of the aerodynamic roll torque on smoothly ablating, spinning cones. The tests, conducted in the Ames 3.5-Foot Hypersonic Wind Tunnel, indicated that the smoothly ablating model rolling at 0 deg angle of attack experiences roll damping, but when rolling at angle of attack an aerodynamic torque in the direction of spin arises if thermal expansion of the body surface occurs. An analysis of the spinning body at angle of attack is included to show how the relative importance of the ablator thermal expansion and the surface recession rate determines whether the motion is damped or undamped.

Mcdevitt, J. B.↗
NASA NTRS1972

Effect of nozzle lateral spacing on afterbody drag and performance of twin-jet afterbody models with cone plug nozzles at Mach numbers up to 2.20

Twin-jet afterbody models were investigated by using two balances to measure separately the thrust minus total drag and the afterbody drag at Mach numbers of 0.0 and 0.50 to 2.20 for a constant angle of attack of 0. Translating shroud cone plug nozzles were tested at dry and maximum afterburning power settings with a high-pressure air system used to provide jet total-pressure ratios up to 20.0. Two nozzle lateral spacings were studied by using afterbodies with several interfairing shapes. The close- and wide-spaced afterbodies had identical cross-sectional area distributions when similar interfairings were installed on each. Nozzle cant angles of -5, 0, and 5 degrees were investigated. The results show that the highest overall performance was generally obtained with the close-spaced afterbody, basic interfairings (no base), and uncanted nozzles.

Berrier, B. L.↗
NASA NTRS1973

Evaluation of flow properties behind 120 deg and 140 deg included-angle cones and a Viking 1975 entry vehicle at Mach numbers from 1.60 to 3.95

The flow properties in the wake of 120 degree and 140 degree included angle cones and a model of the preliminary configuration of the Viking 75 entry vehicle were evaluated. Wake flow properties were calculated from total and static pressures measured with a pressure-survey rake. Data are presented for free stream Mach numbers from 1.60 to 3.95, longitudinal stations from 1.0 to 8.39 body diameters downstream of the maximum diameter, and vertical stations from plus 1.04 to minus 1.04 body diameters measured from the wake center line for an angle of attack of zero degrees.

Brown, C. A., Jr.↗
NASA NTRS1970

Supersonic flow calculations for a cone with an elliptic flare

A three-dimensional supersonic flow program is presented for calculating the flow field about a cone at zero angle of attack with an elliptical flare. The program is irrotational, and results remain valid in the region ahead of the first relected characteristic from the points of shock where the shock is no longer axisymmetric.

Lehrhaupt, H.↗
NASA NTRS1973

Effect of nozzle lateral spacing, engine interfairing shape, and angle of attack on the performance of a twin-jet afterbody model with cone plug nozzles

Twin-jet afterbody models were investigated by using two balances to measure separately the thrust minus total axial force and the afterbody drag at Mach numbers from 0 to 1.3. Angle of attack was varied from minus 2 deg to 8.5 deg. Translating shroud cone plug nozzles were tested at dry-power and maximum-afterburning-power settings with a high-pressure air system used to provide jet total-pressure ratios up to 9.0. Two nozzle lateral spacings were studied by using afterbodies with several interfairing shapes. The close- and wide-spaced afterbodies had identical cross-sectional area distributions when similar interfairings were installed on each. The results show that the highest overall performance was obtained with the close-spaced afterbody and basic interfairings. Increasing angle of attack decreased performance for all configurations and conditions investigated.

Berrier, B. L.↗
NASA NTRS1972

Turbulent bursts and rings on a cone in helium at Me = 7.6.

Review of data obtained on turbulent burst geometry and growth characteristics for cone boundary-layer transition in a helium wind tunnel at a boundary-layer edge Mach number (Me) of 7.6. Detailed data concerning turbulent spot geometry and downstream propagation velocities were obtained using a spark schlieren system with sequential spark capability. In one particular test evidence of a symmetrical turbulent burst ring was obtained; all other bursts developed in a singular random manner. Profiles of the apparent outer edges of the bursts were obtained, and the velocities of the leading and trailing edges of the bursts relative to the local velocity were determined. The velocities of the leading and trailing edges were found to be fairly consistent for each observation, with the leading edge of the burst traveling at about local edge velocity, while the trailing edge moved supersonically relative to local speed.

Fischer, M. C.↗
NASA NTRS1973

Laminar boundary layer on a cone near a plane of symmetry.

The three-dimensional laminar boundary layer near the planes of symmetry of a cone with either outflow or inflow is studied in supersonic and hypersonic flow. Solutions are presented for a variety of values of three parameters, namely those of cross flow, external Mach number, and wall enthalpy ratio. Also asymptotic solutions for ranges of pertinent similarity variables are developed and used in numerical analyses so as to assure exponential behavior as the similarity variables approach infinity. Of special interest in the results is the existence for outflow, i.e., for the windward plane of symmetry, of a new solution branch and for inflow of four solution branches. The physical significance of the new solutions is discussed.

Wu, P.↗
NASA NTRS1973

Viscous flow over spinning cones at angle of attack.

A numerical finite-difference method is developed for evaluating the Magnus coefficients on spinning cones in laminar flow. The merged layer, the strong interaction region, and the downstream boundary layer are all considered. The numerical method is a predictor-corrector scheme developed for three-dimensional flows with or without crossflow diffusion. This method is particularly useful in problems in which a symmetry plane does not exist. Several contributions to the Magnus force and moments are considered. These include asymmetries in displacement thickness, centrifugal force and crossflow shear, and the effects of crossflow separation and vortex formation. Comparisons are made with experimental data and other analyses.

Lin, T. C.↗
NASA NTRS1973

Extralunar materials in cone-crater soil 14141.

Radiochemical neutron activation analysis has been used to determine Ni, Zn, Ga, Ge, Cd, In, Ir, and Au in duplicate samples of lunar soil 14141 and in one additional replicate each of soils 14163 and 14259. The concentrations of extralunar trace elements Ni, Ge, Ir, and Au in 14141 and 14163 are, respectively, about 69 and 82% as high as those in 14259. Although most of the mass of 14141 appears to be ejecta from Cone Crater, a sizable contamination by mature Fra Mauro soil such as 14259 is also present. The siderophilic-element concentrations of the subregolith Fra Mauro materials are estimated to be 25 plus or minus 25% of those observed in 14259.

Wasson, J. T.↗
NASA NTRS1973

An experimental program using a 9.7 deg half-angle cone model at free stream Mach number equals 4.88 and alpha prime S of 10 deg and 29.5 deg

The flow field of a blunted cone model at supersonic speeds is described. The data consist of surface pressure measurements, surface oil flow photographs, and schlieren photographs. The tests were conducted in a two-dimensional, blow down type wind tunnel, using air as a test gas. A mercury filled manometer board was used to measure model surface pressure data.

Faria, H. T.↗
NASA NTRS1974

Effects of Reynolds number and model support on the supersonic aerodynamic chacteristics of a 140 deg-included-angle cone

An investigation has been made in the Langley Unitary Plan wind tunnel to determine the effects of Reynolds number and sting-support interference on the static aerodynamic characteristics of a 140 deg-included-angle cone. Base pressures and forces and moments of the model were measured at Mach numbers of 1.50, 2.00, 2.94, and 4.00 for ratios of sting diameter to model diameter that varied from 0.125 to 0.500 through an angle-of-attack range from about minus 4 deg to 13 deg. The Reynolds number, based on model diameter 4.80 in. was varied from 161,000 to 415,000.

Trescot, C. D., Jr.↗
NASA NTRS1973

Effect of steady state coning angle and damping on whirl flutter stability

The main object of this investigation is to find the effect of the steady state coning angle and the damping at the flapping hinge of the blades on the whirl flutter stability boundary and thus to determine the role they can play in narrowing down the gap between theory and experiment. The governing equations of motion, with these two parameters included are derived by the classical Lagrangian approach using quasi-steady blade element theory for aerodynamic forces. A linearized analysis of these equations is applied to two of the wind tunnel models of the previous investigations. The results indicate that these parameters have a marked effect on stability boundary and they may even change the mode of flutter from backward whirl to forward whirl.

Kaza, K. R. V.↗