Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CFD modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58
All sourcesNASA NTRSDOE OSTI
NASA NTRS2005

Investigation of Compressibility Effect for Aeropropulsive Shear Flows

Rocket Based Combined Cycle (RBCC) engines operate within a wide range of Mach numbers and altitudes. Fundamental fluid dynamic mechanisms involve complex choking, mass entrainment, stream mixing and wall interactions. The Propulsion Research Center at the University of Alabama in Huntsville is involved in an on- going experimental and numerical modeling study of non-axisymmetric ejector-based combined cycle propulsion systems. This paper attempts to address the modeling issues related to mixing, shear layer/wall interaction in a supersonic Strutjet/ejector flow field. Reynolds Averaged Navier-Stokes (RANS) solutions incorporating turbulence models are sought and compared to experimental measurements to characterize detailed flow dynamics. The effect of compressibility on fluids mixing and wall interactions were investigated using an existing CFD methodology. The compressibility correction to conventional incompressible two- equation models is found to be necessary for the supersonic mixing aspect of the ejector flows based on 2-D simulation results. 3-D strut-base flows involving flow separations were also investigated.

Balasubramanyam, M. S.↗
NASA NTRS2013

Trajectory Reconstruction and Uncertainty Analysis Using Mars Science Laboratory Pre-Flight Scale Model Aeroballistic Testing

As part of the Mars Science Laboratory (MSL) trajectory reconstruction effort at NASA Langley Research Center, free-flight aeroballistic experiments of instrumented MSL scale models was conducted at Aberdeen Proving Ground in Maryland. The models carried an inertial measurement unit (IMU) and a flush air data system (FADS) similar to the MSL Entry Atmospheric Data System (MEADS) that provided data types similar to those from the MSL entry. Multiple sources of redundant data were available, including tracking radar and on-board magnetometers. These experimental data enabled the testing and validation of the various tools and methodologies that will be used for MSL trajectory reconstruction. The aerodynamic parameters Mach number, angle of attack, and sideslip angle were estimated using minimum variance with a priori to combine the pressure data and pre-flight computational fluid dynamics (CFD) data. Both linear and non-linear pressure model terms were also estimated for each pressure transducer as a measure of the errors introduced by CFD and transducer calibration. Parameter uncertainties were estimated using a "consider parameters" approach.

Lugo, Rafael A.↗
NASA NTRS1991

Computation of a circular-to-rectangular transition duct flow field

This paper presents the results of a Computational Fluid Dynamics (CFD) calibration study of flow through a circular-to-rectangular transition duct. The design of these ducts is critical to the optimum performance of aircraft with rectangular exhaust nozzles, since these ducts transfer the flow from the gas turbine engine to the exhaust nozzle. Two duct inflow conditions are considered, the first with straight inflow and the second with swirling inflow. Both flows contain realistic wall boundary layers. The first case permits examination of the effects of the geometric transition on the flowfield, while the second case adds in the rotational flow effect that can be present from the gas turbine engine. The flowfields associated with the two cases have been shown, both with CFD and experiment, to have significant differences. The Navier-Stokes CFD code PARC with the Baldwin and Lomax turbulence model was used in this study. The turbulence model had to be modified for both cases in order to achieve accurate determination of the edge of the wall bounded vorticity layers and thus turbulent viscosity. The results of this calibration study will be valuable to aircraft designers who rely on CFD to assist in the design and evaluation of propulsion systems.

Sirbaugh, J. R.↗
NASA NTRSDate not supplied

Validation Experiments for Turbulent Separation over an Axisymmetric Body of Revolution

Historically, the flow physics involved with most turbulent separated flows have presented fundamental challenges to validating numerical approaches. As recognized by the CFD Vision 2030 study commissioned by NASA, validation of Reynolds-averaged Navier-Stokes (RANS) models and other scale-resolving methods for turbulent separated flow requires data from advanced, high-fidelity experiments designed specifically for CFD implementation. In accordance with this effort, a new test platform, referred to as the NASA Axisymmetric Afterbody, was designed to obtain detailed measurements of the flow field undergoing a smooth, adverse pressure gradient induced separation for a fixed Reynolds number, Re = 180,000. The parametric body offers a range of flow states progressing from fully attached, to incipient separation, and finally to small-scale separated flow based on variable afterbody geometries. In an initial effort to evaluate RANS turbulence model capabilities, the present configurations of the axisymmetric model host a mild adverse pressure gradient over the contoured boattail section, inducing incipient turbulent separation, as well as a slightly larger adverse pressure gradient, inducing a small-scale region of turbulent separation. Experiments include steady pressure measurements and 2-D PIV to provide the preliminary dataset for simulation studies, which examine the effect of variable grid domains and RANS turbulence models. This is done in an effort to understand and evaluate the critical variability between solutions for the present model configurations. Results indicate potential discrepancies may be due to the effect of the square tunnel test section walls, relatively large blockage ratio, and slight variability in reference parameters. Ongoing work will focus on higher fidelity experimental campaigns to obtain surface flow visualizations and Stereo-Particle Image Velocimetry (SPIV) to deliver higher spatial resolution of the three-dimensional flow field to aid turbulence modelers.

Validation↗
NASA NTRS1998

Transmission and Incidence Losses for a Slotted Plate

The objective of this work is to find a model of the stagnation pressure loss resulting from flow through a slotted plate, which is effectively a cascade of flat plate airfoils, particularly at very large angles of incidence. Data from a published experiment is examined, and compared with control volume analysis, and CFD code calculations. An assumption that the loss can be separated into a transmission loss and an incidence loss seems to be justified by the data. Both the data and the CFD code results are consistent with an incidence loss model in which the flow component normal to the slot axis is lost. However, the experimental transmission loss is much larger than calculated values.

Wilson, Jack↗
NASA NTRS2007

Temperature-Corrected Model of Turbulence in Hot Jet Flows

An improved correction has been developed to increase the accuracy with which certain formulations of computational fluid dynamics predict mixing in shear layers of hot jet flows. The CFD formulations in question are those derived from the Reynolds-averaged Navier-Stokes equations closed by means of a two-equation model of turbulence, known as the k-epsilon model, wherein effects of turbulence are summarized by means of an eddy viscosity. The need for a correction arises because it is well known among specialists in CFD that two-equation turbulence models, which were developed and calibrated for room-temperature, low Mach-number, plane-mixing-layer flows, underpredict mixing in shear layers of hot jet flows. The present correction represents an attempt to account for increased mixing that takes place in jet flows characterized by high gradients of total temperature. This correction also incorporates a commonly accepted, previously developed correction for the effect of compressibility on mixing.

Abdol-Hamid, Khaled S.↗
NASA NTRSDate not supplied

Kinetic and Transport Modeling for Entry Flows in Hydrogen-Helium Atmospheres

Several different thermochemical models for H2/He mixtures are used to simulate a 1-D shock in a viscous CFD code at conditions relevant for hypersonic entry into the ice and gas giants. These models range from a 6-species, 1-temperature (1-T) model, to more complex 17 and 25-species state-to-state (StS) models. Corresponding radiance profiles for each of these models are then computed using a radiation code, and results are compared to experimental data from the NASA Ames Electric Arc Shock Tube (EAST) facility. Overall, the 6-species model with a quasi-steady state (QSS) solver for atomic H and modified ionization rates, along with the 17 and 25-species StS models, are found to reproduce the magnitude of the radiance seen in the EAST experiments reasonably accurately. Two additional changes to the modeling of species diffusion fluxes are also investigated: the exclusion of a ∇W term, as well as the inclusion of Soret/ Dufour effects. It is determined that these changes to the transport modeling have a negligible impact on the flowfield and therefore the radiance predictions for the H2/He shock conditions considered in this study.

Outer planets↗
NASA NTRS2009

Application of Stereo PIV on a Supersonic Parachute Model

The Mars Science Laboratory (MSL) is the next step in NASA's Mars Exploration Program, currently scheduled for 2011. The spacecraft's descent into the Martian atmosphere will be slowed from Mach 2 to subsonic speeds via a large parachute system with final landing under propulsive control. A Disk-Band-Gap (DBG) parachute will be used on MSL similar to the designs that have been used on previous missions, however; the DBG parachute used by MSL will be larger (21.5 m) than in any of the previous missions due to the weight of the payload and landing site requirements. The MSL parachute will also deploy at higher Mach number (M 2) than previous parachutes, which can lead to instabilities in canopy performance. Both the increased size of the DBG above previous demonstrated configurations and deployment at higher Mach numbers add uncertainty to the deployment, structural integrity and performance of the parachute. In order to verify the performance of the DBG on MSL, experimental testing, including acquisition of Stereo Particle Imaging Velocimetry (PIV) measurements were required for validating CFD predictions of the parachute performance. A rigid model of the DBG parachute was tested in the 10x10 foot wind tunnel at GRC. Prior to the MSL tests, a PIV system had never been used in the 10x10 wind tunnel. In this paper we discuss some of the technical challenges overcome in implementing a Stereo PIV system with a 750x400 mm field-of-view in the 10x10 wind tunnel facility and results from the MSL hardshell canopy tests.

Wernet, Mark P.↗
NASA NTRS1991

Hi-alpha forebody design. Part 2: Determination of body shapes for positive directional stability

Computational Fluid Dynamics (CFD) has been used to study aircraft forebody flowfields at low speed high angle-of-attack conditions with sideslip. The purpose is to define forebody geometries which provide good directional stability characteristics under these conditions. The flows of the F-5A forebody and Erickson forebody were recomputed with better and refined grids. The results were obtained using a modified version of cfl3d to solve either the Euler equations or the Reynolds equations employing a form of the Baldwin-Lomax turbulence model. Based on those results, we conclude that current CFD methods can be used to investigate the aerodynamic characteristics of forebodies to achieve desirable high angle-of-attack characteristics. An analytically defined generic forebody model is described, and a systematic study of forebody shapes was then conducted to determine which shapes promote a positive contribution to directional stability at high angle-of-attack. A novel way of presenting the results is used to illustrate how the positive contribution arises. Based on the results of this initial parametric study, some guidelines for aerodynamic design to promote positive directional stability are presented.

Ravi, R.↗
NASA NTRS2015

Wind Tunnel Interference Effects on Tilt Rotor Testing Using Computational Fluid Dynamics

Experimental techniques to measure rotorcraft aerodynamic performance are widely used. However, most of them are either unable to capture interference effects from bodies, or require an extremely large computational budget. The objective of the present research is to develop an XV-15 Tilt Rotor Research Aircraft rotor model for investigation of wind tunnel wall interference using a novel Computational Fluid Dynamics (CFD) solver for rotorcraft, RotCFD. In RotCFD, a mid-fidelity URANS solver is used with an incompressible flow model and a realizable k-ε turbulence model. The rotor is, however, not modeled using a computationally expensive, unsteady viscous body-fitted grid, but is instead modeled using a blade element model with a momentum source approach. Various flight modes of the XV-15 isolated rotor, including hover, tilt and airplane mode, have been simulated and correlated to existing experimental and theoretical data. The rotor model is subsequently used for wind tunnel wall interference simulations in the National Full-Scale Aerodynamics Complex (NFAC) at NASA Ames Research Center in California. The results from the validation of the isolated rotor performance showed good correlation with experimental and theoretical data. The results were on par with known theoretical analyses. In RotCFD the setup, grid generation and running of cases is faster than many CFD codes, which makes it a useful engineering tool. Performance predictions need not be as accurate as high-fidelity CFD codes, as long as wall effects can be properly simulated. For both test sections of the NFAC wall interference was examined by simulating the XV-15 rotor in the test section of the wind tunnel and with an identical grid but extended boundaries in free field. Both cases were also examined with an isolated rotor or with the rotor mounted on the modeled geometry of the Tiltrotor Test Rig (TTR). A 'quasi linear trim' was used to trim the thrust for the rotor to compare the power as a unique variable. Power differences between free field and wind tunnel cases were found from -7 % to 0 % in the 80- by 120-Foot Wind Tunnel test section and -1.6 % to 4.8 % in the 40- by 80-Foot Wind Tunnel, depending on the TTR orientation, tunnel velocity and blade setting. The TTR will be used in 2016 to test the Bell 609 rotor in a similar fashion to the research in this report.

CFD↗
NASA NTRSDate not supplied

Near-Body Mesh Adaption for Transitional Flows Using OVERFLOW

Accurate modeling of boundary-layer transition is an important aspect of developing greener air transport technologies. In that regard, transition models based on auxiliary transport equations offer a robust approach that is easily integrated into the Reynolds-averaged Navier-Stokes (RANS) solvers. Recent workshops under NATO and AIAA have identified the verification of transport-equations-based transition modeling as a critical aspect of reducing the scatter between the predictions of different CFD codes. Follow-on work has highlighted the need for highly dense grids to achieve an asymptotic convergence of transition related flow metrics. The present work examines the role of automatic near-body mesh adaptation capability in the NASA OVERFLOW CFD solver to enable verification studies in an efficient manner, and for establishing best practices for designing grids for the RANS-based transition models. A sensor function relevant to the Langtry-Menter \gamma-Re_{\theta t}\ transition model has been identified and used for error-based mesh adaptation for canonical configurations comprising a flat plate, and the S809 and NLR-7301 airfoils. The efficacy of the mesh adaptation approach is assessed for flow conditions involving multiple transition scenarios such as natural transition, separation-induced transition, and shock-induced transition. The results from this exploratory study indicate that the meshes adapted using the proposed sensor provide solutions that approach the references solutions obtained with uniformly refined hand-crafted meshes, in terms of the chosen metrics, and yield modest yet significant savings in grid count. We also highlight areas for improvement in the grid adaptation methodology within OVERFLOW.

CFD↗
NASA NTRSDate not supplied

Heated Supersonic Axisymmetric Jet Cases for the NASA Turbulence Modeling Resource

Three new supersonic jet cases were built for the NASA Turbulence Modeling Resource (TMR). These cases were taken from the 6th AIAA Propulsion Aerodynamics Workshop (PAW) nozzle test problem, which utilized data taken at NASA GRC consisting of non-intrusive measurements of jet plume velocities and temperatures, including both mean values and turbulence statistics. The three jet cases all used a Mach 1.63 axisymmetric nozzle: a heated jet for each at on-design conditions, a temperature-matched on-design condition at Mach 1.63, and an off-design heated condition for the Mach 1.63 nozzle. Computational fluid dynamics (CFD) solutions are obtained using three established Reynolds-averaged Navier-Stokes (RANS) codes: Wind-US, FUN3D, and VULCAN-CFD, all using the Menter Shear Stress Transport k- turbulence model with vorticity source term (SST-V). The NASA TMR requires at least two CFD codes yielding essentially identical results to certify that the approaches are verified, meaning that they solve the posed CFD equations as intended. The three codes generally provided very close agreement with each other for jet plume quantities, with the only exception being static temperature. This discrepancy was determined to be the result of whether or not turbulent kinetic energy was considered in the definition of total energy. Validation of the SST-V turbulence model for this case (its level of agreement/disagreement with experimental data) is also addressed.

turbulance↗
NASA NTRS1992

Hover performance analysis of advanced rotor blades

This is an effort aimed at validating recent hover prediction methods. The experimental basis for this validation work is an extensive set of loads, wake and performance data, which were obtained from a pressure instrumented model UH-60 rotor tested at the Sikorsky hover test facility and at Duits-Nederlandse Windtunnel (DNW). This model was equipped with replaceable tips - including a tapered and a BERP-type tip - which permitted studies of the effects of rotor geometry. The central prediction method studied is a free-wake, vortex embedded, full-potential CFD method - called HELIX-I. It is found that the HELIX-I code produces very good comparisons with the data including wake, surface pressure and performance. Comparisons with the measured radial load distributions have permitted an improved understanding of the wake resolution modelling requirements of CFD methods. Since HELIX-I is a combined Eulerian/Lagrangian method, limited comparisons are also made with a Lagrangian boundary element code (called EHPIC) and an Eulerian Navier-Stokes code (called TURNS). In most cases all methods produce good comparisons with the data. It is found that the HELIX-I code provides a good compromise between the speed of boundary integral methods and the comprehensive nature of Navier-Stokes methods.

Tung, C.↗
NASA NTRS1995

A 3-D Navier-Stokes CFD study of turbojet/ramjet nozzle plume interactions at Mach 3.0 and comparison with data

Advanced airbreathing propulsion systems used in Mach 4-6 mission scenarios, usually consist of a single integrated turboramjet or as in this study, a turbojet housed in an upper bay with a separate ramjet housed in a lower bay. As the engines transition from turbojet to ramjet, there is an operational envelope where both engines operate simultaneously. One nozzle concept under consideration has a common nozzle, where the plumes from the turbojet and ramjet interact with one another as they expand to ambient conditions. In this paper, the two plumes interact at the end of a common 2-D cowl, when they both reach an approximate Mach 3.0 condition and then jointly expand to Mach 3.6 at the common nozzle exit plane. At this condition, the turbojet engine operated at a higher NPR than the ramjet, where the turbojet overpowers the ramjet plume, deflecting it approximately 12 degrees downward and in turn the turbojet plume is deflected 6 degrees upward. In the process, shocks were formed at the deflections and a shear layer formed at the confluence of the two jets. This particular case was experimentally tested and the data used to compare with the PARC3D code with k-kl two equation turbulence model. The 2-D and 3-D centerline CFD solutions are in good agreement, but as the CFD solutions approach the outer sidewall, a slight variance occurs. The outer wall boundary layers are thin and do not present much of an interaction, however, where the confluence interaction shocks interact with the thin boundary layer on the outer wall, strong vortices run down each shock causing substantial disturbances in the boundary layer. These disturbances amplify somewhat as they propagate downstream axially from the confluence point. The nozzle coefficient (CFG) is reduced 1/2 percent as a result of this sidewall interaction, from 0.9850 to 0.9807. This three-dimensional reduction is in better agreement with the experimental value of 0.9790.

Chang, Ing↗
NASA NTRS2017

Design of an Axisymmetric Afterbody Test Case for CFD Validation

As identified in the CFD Vision 2030 Study commissioned by NASA, validation of advanced RANS models and scale-resolving methods for computing turbulent flow fields must be supported by continuous improvements in fundamental, high-fidelity experiments designed specifically for CFD implementation. In accordance with this effort, the underpinnings of a new test platform referred to herein as the NASA Axisymmetric Afterbody are presented. The devised body-of-revolution is a modular platform consisting of a forebody section and afterbody section, allowing for a range of flow behaviors to be studied on interchangeable afterbody geometries. A body-of-revolution offers advantages in shape definition and fabrication, in avoiding direct contact with wind tunnel sidewalls, and in tail-sting integration to facilitate access to higher Reynolds number tunnels. The current work is focused on validation of smooth-body turbulent flow separation, for which a six-parameter body has been developed. A priori RANS computations are reported for a risk-reduction test configuration in order to demonstrate critical variation among turbulence model results for a given afterbody, ranging from barely-attached to mild separated flow. RANS studies of the effects of forebody nose (with/without) and wind tunnel boundary (slip/no-slip) on the selected afterbody are presented. Representative modeling issues that can be explored with this configuration are the effect of higher Reynolds number on separation behavior, flow physics of the progression from attached to increasingly-separated afterbody flows, and the effect of embedded longitudinal vortices on turbulence structure.

Disotell, Kevin J.↗
NASA NTRS2012

Production Level CFD Code Acceleration for Hybrid Many-Core Architectures

In this work, a novel graphics processing unit (GPU) distributed sharing model for hybrid many-core architectures is introduced and employed in the acceleration of a production-level computational fluid dynamics (CFD) code. The latest generation graphics hardware allows multiple processor cores to simultaneously share a single GPU through concurrent kernel execution. This feature has allowed the NASA FUN3D code to be accelerated in parallel with up to four processor cores sharing a single GPU. For codes to scale and fully use resources on these and the next generation machines, codes will need to employ some type of GPU sharing model, as presented in this work. Findings include the effects of GPU sharing on overall performance. A discussion of the inherent challenges that parallel unstructured CFD codes face in accelerator-based computing environments is included, with considerations for future generation architectures. This work was completed by the author in August 2010, and reflects the analysis and results of the time.

Duffy, Austen C.↗
NASA NTRS2011

Toward Supersonic Retropropulsion CFD Validation

This paper begins the process of verifying and validating computational fluid dynamics (CFD) codes for supersonic retropropulsive flows. Four CFD codes (DPLR, FUN3D, OVERFLOW, and US3D) are used to perform various numerical and physical modeling studies toward the goal of comparing predictions with a wind tunnel experiment specifically designed to support CFD validation. Numerical studies run the gamut in rigor from code-to-code comparisons to observed order-of-accuracy tests. Results indicate that this complex flowfield, involving time-dependent shocks and vortex shedding, design order of accuracy is not clearly evident. Also explored is the extent of physical modeling necessary to predict the salient flowfield features found in high-speed Schlieren images and surface pressure measurements taken during the validation experiment. Physical modeling studies include geometric items such as wind tunnel wall and sting mount interference, as well as turbulence modeling that ranges from a RANS (Reynolds-Averaged Navier-Stokes) 2-equation model to DES (Detached Eddy Simulation) models. These studies indicate that tunnel wall interference is minimal for the cases investigated; model mounting hardware effects are confined to the aft end of the model; and sparse grid resolution and turbulence modeling can damp or entirely dissipate the unsteadiness of this self-excited flow.

Kleb, Bil↗
NASA NTRS1992

CFD lends the government a hand

The present survey of important and novel CFD applications being developed and implemented by U.S. Government contractors gives attention to naval vessel flow-modeling, Army ballistic and rotary wing aerodynamics, and NASA hypersonic vehicle related applications of CFD. CFD-generated knowledge of numerical algorithms, fluid motion, and supercomputer use is being incorporated into such additional areas as computational electromagnetics and acoustics. Attention is presently given to CFD methods' development status in such fields as submarine boundary layers, hypersonic kinetic energy projectile shock structures, helicopter main rotor tip flows, and National Aerospace Plane aerothermodynamics.

Lekoudis, Spiro↗