Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Attribution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Effects of Deposition Temperature on the Structural and Physical Properties of Ba(Fe{sub 1.8}Co{sub 0.2}){sub 2}As{sub 2} Thin Film

Ba(Fe{sub 1.8}Co{sub 0.2}){sub 2}As{sub 2} thin films have been grown directly on (001) SrTiO{sub 3} (STO) substrates by pulsed laser deposition at the temperatures from 640 to 700 {sup ∘}C. Effects of deposition temperature (T{sub s}) on the structure, magnetic, and superconducting properties of the films are investigated systematically. It is found that Ba(Fe{sub 1.8}Co{sub 0.2}){sub 2}As{sub 2} film grown at lower deposition temperature is polycrystalline, and the optimized temperature of 685 {sup ∘}C can yield high-quality epitaxial Ba(Fe{sub 1.8}Co{sub 0.2}){sub 2}As{sub 2} film. The (002) diffraction peak of Fe metal at 2𝜃 =∼ 65{sup ∘} is observed along with the (00l) diffraction peaks of Ba(Fe{sub 1.8}Co{sub 0.2}){sub 2}As{sub 2} films deposited at all temperatures, which is attributed to the decomposition of BaFe{sub 1.8}Co{sub 0.2}As{sub 2} target when a high-energy pulsed laser hit on the target in a high vacuum. X-ray photoelectron spectra of Fe 2p show that the relative percentage of zerovalent ion (Fe{sup 0}) is almost equal to that of divalent ion (Fe{sup 2+}) for the film deposited at 670 {sup ∘}C, which is different from that most Fe{sup 2+} ions exist in the BaFe{sub 1.8}Co{sub 0.2}As{sub 2} target. The saturation magnetization (M{sub s}) increases from 7.88 to 240.5 emu/cm{sup 3} monotonously with the increase of Ba(Fe{sub 1.8}Co{sub 0.2}){sub 2}As{sub 2} film deposition temperature. The maximum zero-resistance temperature (T{sub c}{sup 0}) of ∼16 K was obtained, which can be attributed to the high quality of the Ba(Fe{sub 1.8}Co{sub 0.2}){sub 2}As{sub 2} film. The coexistence of superconductivity (SC) and ferromagnetism (FM) in the BaFe{sub 1.8}Co{sub 0.2}As{sub 2} films was discussed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2019

Influence of Packing Atmosphere on the Microstructures and Transport Properties of Bi-2223/AgAu Tapes

Oxygen partial pressure was the key factor to tune the phase evolution mechanism of Bi-2223 system. In order to investigate the influence of packing atmosphere on the phase formation rate of Bi-2223, microstructures‚ and the current capacity of final tapes‚ 37-filamentary Bi-2223/AgAu tapes were fabricated by powder-in-tube (PIT) process, and the powder packing process operated in the glove box under different atmosphere of pure O{sub 2}‚ air, and N{sub 2}–7.5%O{sub 2}, with the oxygen partial pressure of 100%‚ 25%, and 7.5%, respectively. With different packing atmosphere, the phase formation rate of Bi-2223 increased obviously during the first heat treatment process (HT1). While, based on the same HT1 process, the maximum Bi-2223 phase content was obtained in the tapes with packing atmosphere of N{sub 2}–7.5%O{sub 2}‚ which should be attributed to the suitable Bi-2223 content and distribution. Due to the improvement of superconducting phase content and better texture structure, the critical current density increased with decreasing oxygen partial pressure of packing atmosphere and the maximum value of 19.9 kA/cm{sup 2} was reached. Moreover‚ the in-field current capacities of these Bi-2223/AgAu tapes have also been enhanced with low oxygen partial pressure in packing atmosphere, attributed to the improvements of intergrain connectivity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2019

AC Magnetic Susceptibility of Y{sub 3}Ba{sub 5}Cu{sub 8}O{sub 18} Substituted by Nd{sup 3+} and Ca{sup 2+} Ions

Effect of Nd{sup 3+} and Ca{sup 2+} ion substitutions in Y{sub 3}Ba{sub 5}Cu{sub 8}O{sub 18} (Y-358) was studied using X-ray diffraction (XRD), scanning electron microscopy (SEM), electrical resistivity, and ac magnetic susceptibility measurements. Superconducting samples of type Y{sub 3 − x}Nd{sub x}Ba{sub 5 − y}Ca{sub y}Cu{sub 8}O{sub 18} (with 0 ≤ x, y ≤ 0.4) were synthesized by the standard solid-state reaction technique. XRD patterns revealed that all the samples were mainly composed of Y-358 phase with orthorhombic structure. SEM micrographs showed that Nd{sup 3+} and Ca{sup 2+} ion substitutions had the ability to alter the grain morphology of Y-358 to irregular randomly oriented grains with smaller average grain sizes. The temperature-dependent electrical resistivity curves indicated that the superconducting transition temperature T{sub c} was decreased from 96.51 to 87.41 K as the substitution contents were increased from 0 to 0.4. Detailed AC magnetic susceptibility measurements were done using a quantum design physical property measurement system (PPMS) at different dc fields (B = 0.5–20 kG) and frequency of 1 kHz. A comparison between electrical resistivity and AC magnetic susceptibility data was performed. It was found that T{sub cs} obtained from AC magnetic susceptibility were much lower than those obtained from the resistivity measurements, for all studied samples. This was discussed in terms of filamentary paths that could produce sharp pronounced drops in diamagnetism. Generally, the depression in T{sub c} was attributed to the decrease in relative volume fraction of Y-358 or due to trapping of mobile holes or other mechanism connected with oxygen vacancy disorder. Werthamer–Helfand–Hohenberg (WHH) theory was employed to study the temperature dependence of the upper critical magnetic field B{sub c2}(T) for the samples. The relative importance of both orbital and paramagnetic effects in the suppression of superconductivity was described with the aid of Maki parameter (κ{sub M}). The estimated values of the upper critical magnetic field at 0 K, B{sub c2}(0), were found to decrease from 37.3 to 13.5 T as Nd{sup 3+} and Ca{sup 2+} contents were increased from 0 to 0.4. This decrement was attributed to the weak electron–phonon coupling and to the orbital as well as spin pair breaking mechanisms. Furthermore, Ginzburg–Landau coherence length ξ{sub GL} of Y{sub 3 − x}Nd{sub x}Ba{sub 5 − y}Ca{sub y}Cu{sub 8}O{sub 18} was found to increase with the increase of the Nd{sup 3+} and Ca{sup 2+} contents. Therefore, Nd{sup 3+} and Ca{sup 2+} ions play an important role in the pair-breaking mechanism and in suppressing superconductivity of the Y-358 phase.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Grass(stage)root movement to ensure future resilience of longleaf pine ecosystems

Recent interest in restoring longleaf pine ecosystems highlights the need for an improved understanding, appreciation, and consideration of longleaf pine’s unique life history compared to other southern pines. Longleaf pine ecosystems are considered more resilient than other southern pine ecosystems and the attributes that confer this resilience may be related to belowground carbon allocation patterns that occur during the seedling stage of its life history where it exists for years in a grass stage. The long residence time spent in the grass stage has impeded adoption of longleaf pine by landowners for decades, which has resulted in efforts to expedite emergence from the grass stage through silviculture, nursery production, and selection breeding techniques; however, expedited emergence may come at the expense of root and belowground carbohydrate storage reserve development —traits that purportedly enhance longleaf pine tree and ecosystem resilience relative to other southern pine species. Furthermore, I caution that efforts to expedite longleaf pine emergence from the grass stage also consider the potential implications on belowground carbon allocation and identify research priorities to help facilitate the improvement of longleaf pine seedling silviculture, nursery production, and breeding in a way that ensures the maintenance of attributes linked to resilience.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Analyzing users’ preferences between personal and pooled rideshare services using a mixed logit modeling approach

Ridesharing has become an increasingly popular transportation method over the past decade. Transportation network companies such as Uber and Lyft generally provide two types of rideshare services: personal rideshare, in which users ride alone or with individuals they know, and pooled rideshare, in which users ride with passengers they do not know but share similar routes. Pooled rideshare is capable of reducing energy consumption and traffic in the transportation system in comparison to personal rideshare. Despite the growth in trip volume, ridesharing usage is still low compared to other popular transportation methods in the U.S., particularly traveling in one’s own personal vehicle. Furthermore, pooled rideshare usage is lower than personal rideshare. To understand riders’ preferences, a national survey (N = 2884) was conducted in the U.S. to investigate users’ choice behaviors in rideshare services examining personal versus pooled rideshare. Each survey respondent completed 20 stated-preference scenarios where participants choose between a personal or pooled rideshare option. Based on the responses, a mixed logit model was developed to capture the choice behavior preferences of the participants. The model unveiled the impact of demographic and trip attribute variables on users’ rideshare preferences. The discussion encompassed insights into demographic backgrounds and trip attributes, accompanied by a set of policy recommendations aimed at enhancing future pooled rideshare utilization.

Choice model↗
DOE OSTI2023

Structural comparison of allophycocyanin variants reveals the molecular basis for their spectral differences

Abstract Allophycocyanins are phycobiliproteins that absorb red light and transfer the energy to the reaction centers of oxygenic photosynthesis in cyanobacteria and red algae. Recently, it was shown that some allophycocyanins absorb far-red light and that one subset of these allophycocyanins, comprising subunits from the ApcD4 and ApcB3 subfamilies (FRL-AP), form helical nanotubes. The lowest energy absorbance maximum of the oligomeric ApcD4-ApcB3 complexes occurs at 709 nm, which is unlike allophycocyanin (AP; ApcA-ApcB) and allophycocyanin B (AP-B; ApcD-ApcB) trimers that absorb maximally at ~ 650 nm and ~ 670 nm, respectively. The molecular bases of the different spectra of AP variants are presently unclear. To address this, we structurally compared FRL-AP with AP and AP-B, performed spectroscopic analyses on FRL-AP, and leveraged computational approaches. We show that among AP variants, the α-subunit constrains pyrrole ring A of its phycocyanobilin chromophore to different extents, and the coplanarity of ring A with rings B and C sets a baseline for the absorbance maximum of the chromophore. Upon oligomerization, the α-chromophores of all AP variants exhibit a red shift of the absorbance maximum of ~ 25 to 30 nm and band narrowing. We exclude excitonic coupling in FRL-AP as the basis for this red shift and extend the results to discuss AP and AP-B. Instead, we attribute these spectral changes to a conformational alteration of pyrrole ring D, which becomes more coplanar with rings B and C upon oligomerization. This study expands the molecular understanding of light-harvesting attributes of phycobiliproteins and will aid in designing phycobiliproteins for biotechnological applications.

Gisriel, Christopher J.↗
DOE OSTI2017

Grain Growth in Nanocrystalline Mg-Al Thin Films

An improved understanding of grain growth kinetics in nanocrystalline materials, and in metals and alloys in general, is of continuing interest to the scientific community. In this study, Mg - Al thin films containing ~10 wt.% Al and with 14.5 nm average grain size were produced by magnetron-sputtering and subjected to heat-treatments. The grain growth evolution in the early stages of heat treatment at 423 K (150 °C), 473 K (200 °C) and 573K (300 °C) was observed with transmission electron microscopy and analyzed based upon the classical equation developed by Burke and Turnbull. The grain growth exponent was found to be 7±2 and the activation energy for grain growth was 31.1±13.4 kJ/mol, the latter being significantly lower than in bulk Mg-Al alloys. The observed grain growth kinetics are explained by the Al supersaturation in the matrix and the pinning effects of the rapidly forming beta precipitates and possibly shallow grain boundary grooves. The low activation energy is attributed to the rapid surface diffusion which is dominant in thin film systems.

activation energy↗
DOE OSTI2021

Microstructure, Hardness, and Residual Stress of the Dissimilar Metal Weldments of SA508-309L/308L-304L

A dissimilar metal weldment consisting of SA508-309L-308L-304L is widely used in light-water nuclear reactors. These weldments demonstrate dissimilar susceptibility to stress corrosion cracking that are related to the microstructure, properties, and residual stress. In this work, microstructures, hardness, and the residual stress distribution of the dissimilar metal weldments were investigated, with the correlation of increased hardness in the heat-affected zone (HAZ) to the microstructure. 304L HAZ demonstrated similar grain morphology as the base material, and the increase in hardness was primarily attributed to the increased dislocation density. SA508 HAZ demonstrated a change of grain morphology resulting from the different peak temperatures and cooling rates. The increased hardness in the SA508 HAZ was attributed to the refined grain morphology, higher dislocation density, and higher number density of precipitates. A ~ 20–30-μm-wide martensitic zone formed at the fusion boundary of SA508-309L, where Cr-rich carbide precipitates were observed, with the average size and the number density of 44.1 ± 16.9 nm and 1.5 × 10 21 m ₋3 , respectively. In conclusion, residual stress results demonstrated the largest tensile stress at 309L butter, indicating its high cracking susceptibility.

36 MATERIALS SCIENCE↗
DOE OSTI2022

In-Situ Observation of FCC→HCP Transformation-Induced Plasticity Behavior During Dynamic Deformation of CoCrNi Multi-principal Element Alloys

CoCrNi multi-principal element alloys (MPEAs) have potential as high toughness, blast resistant materials, but limited studies of their high strain rate behavior have been performed. Their high toughness has been attributed to low stacking fault energies and the activation of toughness enhancing deformation mechanisms, such as twinning- and transformation-induced plasticity (TWIP and TRIP, respectively), that may be affected by increased strain rate. This work examines a series of CoCrNi MPEAs tested with a miniaturized pressure bar, while simultaneous synchrotron x-ray diffraction and imaging are performed, and compares these results to those collected during quasi-static deformation at elevated temperatures. Here, the collected diffraction indicates that TRIP was active at elevated strain rates for the most Co-rich alloys containing 50 or 55 at. pct. Co, while TRIP behavior was suppressed at elevated strain rates in a 40 at. pct. Co alloy anticipated to experience TRIP. The suppression of TRIP in the lower Co alloy at high strain rates is attributed to adiabatic heating, consistent with suppression of TRIP as a result of elevated temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Understanding the Formation and Evolution of Oxide Inclusions in Si-Deoxidized Spring Steel

To illustrate the mechanism of the formation and evolution of inclusions in Si-deoxidized spring steel, pilot trials and systematic samplings were conducted, and detailed information about the inclusion density, morphology and composition was elucidated by electron probe X-ray microanalysis. The steel samples were collected from the vacuum degassing furnace, tundish furnace and spring rods after hot rolling. Based on the relationship between the mass ratio of X{sub (CaO)}/X{sub (SiO{sub 2)}} and diameters of inclusions, CaO-SiO{sub 2} inclusions were found to be formed by the coalescence between SiO{sub 2} and CaO-SiO{sub 2} inclusions. Most CaO-SiO{sub 2} inclusions > 10 μm were located in the melilite areas with liquidus temperatures < 1400 °C. The Al{sub 2}O{sub 3}-SiO{sub 2}-CaO inclusions in the steel samples from the vacuum degassing and tundish furnaces were considered to be formed by reduction of CaO-SiO{sub 2} inclusions by Al dissolved in steel. The increased number density of Al{sub 2}O{sub 3}-SiO{sub 2}-CaO inclusions in spring rods was primarily attributed to the entrapment of Na{sub 2}O-contained mould flux particles and inclusions crushed after hot rolling. Many Al{sub 2}O{sub 3}-SiO{sub 2}-MnO and SiO{sub 2}-MnO inclusions were observed in tundish furnace samples, which originated from inherent reactions between [Al], [Si], [Mn] and [O] in the molten steel. The SiO{sub 2} precipitation of Al{sub 2}O{sub 3}-SiO{sub 2}-MnO inclusions was attributed to the solubility decrease during the solidification process with temperature drop.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Effects of High Current Pulsed Electron Beam Irradiation on the Mechanical Properties and Cutting Performance of TiAlN-Coated Tools

Commercial TiAlN-coated carbide tools were post-treated using the high current pulsed electron beam irradiation method. The influence of the energy density of the electron beam on the morphology, phase composition, surface roughness and Vickers hardness were investigated. The higher energy density imposed on TiAlN-coated carbide tools resulted in a flatter and harder modified surface. After the beam irradiation, the XRD diffraction peak intensity of the hardening phase (Ti,Al)N was changed, and the diffraction peak position was shifted; these changes are attributed to the improved microhardness of the irradiated coatings. Investigations on the cutting experiments of turning Ti-6Al-4V alloy showed that the irradiated TiAlN-coated carbide tool exhibited longer cutting life and better wear resistance than those of an unirradiated tool. This improvement is attributed to the combined effect of low surface roughness and high microhardness that resulted from the high current pulse electron beam irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Austenitic Reversion of Cryo-rolled Ti-Stabilized Austenitic Stainless Steel: High-Resolution EBSD Investigation

In this study, AISI 321 austenitic stainless steel (ASS) was cryo-rolled and subsequently annealed at 650 and 800 °C to reverse BCC α′-martensite to FCC γ-austenite. The texture evolution associated with the reversion at the selected temperatures was investigated using high-resolution EBSD. After the reversion, TiC precipitates were observed to be more stable in 650 °C-annealed specimens than those reversed at 800 °C. {110} texture was mainly developed in specimens subjected to both annealing temperatures. However, specimens reversed at 650 °C have stronger texture than those annealed at 800 °C, even at the higher annealing time. The strong intensity of {110} texture component is attributed to the ability of AISI 321 ASS to memorize the crystallographic orientation of the deformed austenite, a phenomenon termed texture memory. The development of weaker texture in 800 °C-annealed specimens is attributed to the residual strain relief in grains, dissolution of grain boundary precipitates, and an increase in atomic migration along the grain boundaries. Based on the observed features of the reversed austenite grains and estimation from an existing model, it is suspected that the austenite reversion at 650 and 800 °C undergone diffusional and martensitic shear reversion, respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Mechanical Behavior of Commercially Pure Titanium Weldments at Lower Temperatures

Commercially pure titanium is used for low-temperature applications due to good toughness attributed to single-phase microstructure (α). Electron beam welding (EBW) and gas tungsten arc welding (GTAW) processes have been used for welding two grades of commercially pure titanium (Grade 2 and Grade 4). Martensitic microstructure is found to be finer in the case of EBW joint as compared to GTAW joint due to faster rate of cooling in the former process. Weldments have been characterized to study the mechanical behavior at ambient (298 K) and cryogenic temperatures (20 and 77 K). Strength of weldments increases with the decrease in temperature, which is found to be more prominent in case of Grade 4 titanium as compared to Grade 2. Weld efficiency of Grade 4 is found to be higher at all the temperatures (ambient, 77 and 20 K). However, ultimate tensile strength/yield strength ratio is higher for Grade 2 as compared to Grade 4. % Elongation is found to increase/retained at cryogenic temperatures for Grade 2, and it is found to decrease for Grade 4. Electron backscattered diffraction analysis and transmission electron microscopy of deformed samples confirmed the presence of extensive twinning in Grade 2 and the presence of finer martensitic structure in Grade 4. Fractography analysis of tested specimens revealed the presence of cleavage facets in Grade 4 and dimples in specimens of Grade 2. Higher strength in Grade 4 is attributed to higher oxygen restricting the twin-assisted slip, which is otherwise prominent in Grade 2 titanium.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of Al on Grain Refinement and Mechanical Properties of Mg-3Nd Casting Alloy

The effect of Al on the grain refinement and mechanical properties of as-cast Mg-3Nd alloy was investigated systematically by a series of microstructural analysis, solidification analysis and tensile tests. The results show that Al has an obvious refining effect on the as-cast Mg-3Nd alloy. With increasing Al content, the grain size of the as-cast Mg-3Nd alloy decreases firstly, then increases slightly after the Al content reaching 3 wt.%, and the minimum grain size of the Mg-3Nd alloy is 48 ± 4.0 μm. The refining mechanism can be attributed to the formation of Al{sub 2}Nd particles, which play an important role in the heterogeneous nucleation. The strength and elongation of the Mg-3Nd alloy refined by Al also increase with increasing Al content and slightly decrease when the Al content is more than 3 wt.%, and the strengthening mechanism is attributed to the grain refinement as well as dispersed intermetallic particles. Furthermore, the microstructural thermal stability of the Mg-3Nd-3Al alloy is higher than that of the Mg-3Nd-0.5Zr alloy. Overall, the Mg-3Nd alloy with Al addition is a novel alloy with wide and potential application prospects.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Development of Graphene Nanoplatelet-Reinforced AZ91 Magnesium Alloy by Solidification Processing

It is a challenging task to effectively incorporate graphene nanoplatelets (GNPs) which have recently emerged as potential reinforcement for strengthening metals into magnesium-based matrices by conventional solidification processes due to their large surface areas and poor wettability. A solidification processing which combines mechanical stirring and ultrasonic dispersion of reinforcements in liquid matrix was employed to develop AZ91 magnesium alloy matrix composites reinforced with 0.25 and 0.5 wt.% GNPs. The microstructural studies conducted with scanning and transmission electron microscopes revealed that fairly uniform distribution and dispersion of GNPs through the matrix were achieved due to effective combination of mechanical and ultrasonic stirring. The GNPs embedded into the magnesium matrix led to significant enhancement in the hardness, tensile strength and ductility of the composites compared to those of unreinforced AZ91 alloy. The strength enhancement was predominantly attributed to the grain refinement by the GNP addition and dislocation generation strengthening due to the coefficient of thermal expansion mismatch between the matrix and reinforcement. The improved ductility was attributed to the refinement of β eutectics by transforming from lamellar to the divorced eutectics due to the GNP additions. In addition, the strengthening efficiency of the composite with 0.25 wt.% GNP was found to be higher than those of the composite with 0.5 wt.% GNP as the agglomeration tendency of GNPs is increased with increasing GNP content. These results were compared with those of the GNP-reinforced magnesium composites reported in the literature, indicating the potential of the process introduced in this study in terms of fabricating light and high-performance metal matrix composites.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of Cold Rolling and Heat Treatment on Microstructure and Mechanical Properties of Ti-4Al-1Mn Titanium Alloy

Mechanical behavior of Ti-4Al-1Mn titanium alloy has been studied in annealed, cold-rolled and heat-treated conditions. Room temperature tensile strength as well as % elongation has been found to be low with increasing amount of cold rolling. Lowering of strength in cold worked condition is attributed to premature failure. However, the same has been mitigated after heat treatment. Significant effect of cooling media (air and water) from heat treatment temperature on microstructure was not found except for the degree of fineness of α plates. Optimum properties (strength as well as ductility) were exhibited by samples subjected to 15% cold rolling and heat treatment below β transus temperature, which can be attributed to presence of recrystallized microstructure. In cold worked condition, the microstructure shows fine fragmented α plates/Widmanstätten morphology with high dislocation density along with a large amount of strain fields and twinning, which gets transformed to recrystallized equiaxed microstructure and with plate-like morphology after near β heat treatment. Prior cold work is found to have a significant effect on mechanical properties supported by evolution of microstructure. Twinning is found to be assisting in deformation as well as in recrystallization through the formation of deformation and annealing twins during cold working and heat treatment. Fracture analysis of the tested sample with prior cold work and heat-treated condition revealed quasi-ductile failure as compared to only ductile failure features seen for samples heat treated without prior cold work.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effects of Nb on the Microstructure and Properties of Ti-Added Hypereutectic High-Cr Cast Iron

Effects of Nb on the microstructure and properties of Ti-added hypereutectic high-Cr cast iron were studied. With the addition of Nb, a new phase (Nb,Ti)C was formed. The microstructure analysis revealed that the amount of primary carbides was decreased from 18.6 to 8.8% and the primary and eutectic carbides were greatly refined. The decrease in the amount of primary carbides was attributed with the shrinking of primary M{sub 7}C{sub 3} phase zone in the phase diagram, while the refinement of primary carbides was attributed to the heterogeneous nucleus of (Nb,Ti)C phase for the primary M{sub 7}C{sub 3} carbides. The macrohardness of the alloy increased from 60.8 to 63.5HRC, and the impact toughness increased from 3.8 to 5.2 J cm{sup −2}. Furthermore, the wear resistance was enhanced with the addition of Nb due to the formation of hard (Nb,Ti)C carbides.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of Minor Er on the Microstructure and Properties of Al-6.0Mg-0.4Mn-0.1Cr-0.1Zr Alloys

As-cast Al-6.0Mg-0.4Mn-0.1Cr-0.1Zr alloys containing different additions of Er were prepared. Then, the specimens were carried out homogenization heat treatment, hot rolling, cold rolling, and annealing. The effects of minor Er on the microstructure and properties of Al-6.0Mg-0.4Mn-0.1Cr-0.1Zr alloy were investigated. Results show that addition of Er can refine the microstructure and improve the mechanical properties of the alloys. As for the annealed alloys, the addition of 0.33%Er can increase the tensile strength by 29 MPa. Strength increment is mainly attributed to refinement and the precipitation of Al{sub 3}Er and Al{sub 3}(Er, Zr). Additionally, the minor Er can improve the corrosion resistance of the alloys, which can be attributed to the compact composite oxide film of Er-O and Al-O, purification, and modification.

36 MATERIALS SCIENCE↗