SEARCH · Engineering Papers

Results for “A. Microstructures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Microstructural Passivation of Patterned Al 2 O 3 Back Contacts on CdS/CdTe Solar Cells

Abstract Patterned aluminum oxide (Al 2 O 3 ) back contact on cadmium telluride (CdTe) solar cells can effectively mitigate the loss of the majority carriers while retaining the passivation benefits for minority carriers. This study investigates the impact of the point‐contact geometry on cell performance, where the spacing of the microholes is systematically varied at a constant microhole diameter (≈16 µm). Microhole arrays are created on an evaporated Al 2 O 3 layer (≈30 nm) on CdTe using laser‐beam lithography and selective wet etching processes. Comparative analysis indicates a significant decrease in fill factor (FF) and short‐circuit current ( I SC ) when the contact fraction falls below 30%, likely due to the Al 2 O 3 barrier impeding majority carriers. Above this fraction, FF and I SC are comparable to those of baseline CdTe cells without Al 2 O 3 . Open‐circuit voltage ( V OC ) shows a gradual decrease as Al 2 O 3 coverage is reduced but exhibits a slight increase (<15 mV) when the contact fraction exceeds 30%. Cathodoluminescence (CL) characterization reveals that significantly improved radiative recombination occurs within the CdTe grain bulk with Al 2 O 3 , whereas this effect on grain boundaries is minimal. The findings imply complex local carrier dynamics in the patterned back‐contact region, closely tied to the microstructural properties of CdTe‐based solar cells.

Roy, Etee Kawna↗

DOE OSTI2024

Interdependence of Support Wettability ‐ Electrodeposition Rate‐ Sodium Metal Anode and SEI Microstructure

Abstract This study examines how current collector support chemistry (sodiophilic intermetallic Na 2 Te vs. sodiophobic baseline Cu) and electrodeposition rate affect microstructure of sodium metal and its solid electrolyte interphase (SEI). Capacity and current (6 mAh cm −2 , 0.5–3 mA cm −2 ) representative of commercially relevant mass loading in anode‐free sodium metal battery (AF‐SMBs) are analyzed. Synchrotron X‐ray nanotomography and grazing‐incidence wide‐angle X‐ray scattering (GIWAXS) are combined with cryogenic ion beam (cryo‐FIB) microscopy. Highlighted are major differences in film morphology, internal porosity, and crystallographic preferred orientation e.g. (110) vs. (100) and (211) with support and deposition rate. Within the SEI, sodium fluoride (NaF) is more prevalent with Te−Cu versus sodium hydride (NaH) and sodium hydroxide (NaOH) with baseline Cu. Due to competitive grain growth the preferred orientation of sodium crystallites depends on film thickness. Mesoscale modeling delineates the role of SEI (ionic conductivity, morphology) on electrodeposit growth and onset of electrochemical instability.

Lo, Chang‐An↗

DOE OSTI2025

Synergistic Tuning of Microstructure and Morphology in Carbon Molecular Sieve Hollow Fibers for Propylene/Propane Separation

Abstract Asymmetric carbon molecular sieve (CMS) hollow fiber membranes with tunable micro‐ and macro‐structural morphologies for energy efficient propylene‐propane separation are reported here. A sub‐glass transition temperature (sub‐Tg) thermal oxidative crosslinking strategy enables simultaneous optimization of the intrinsic molecular sieving properties while also reducing the thickness of the CMS “skin” derived from the 6FDA : BPDA/DAM polyimide precursors. Such synergistic tuning of CMS microstructure and macroscopic morphology of CMS hollow fibers enables significantly increased propylene permeance (reaching 186.5 GPU) while maintaining an appealing propylene/propane selectivity of 13.3 for 50/50 propylene/propane mixed gas feeds. Our findings reveal a more refined and versatile tool than available with previous O 2 ‐doping pretreatments. The advanced approach here should be broadly useful to other polyimide precursors and diverse gas pairs.

Liu, Zhongyun [School of Chemical &amp, Biomolecul↗

DOE OSTI2024

Interdependence of Support Wettability - Electrodeposition Rate- Sodium Metal Anode and SEI Microstructure

Here, this study examines how current collector support chemistry (sodiophilic intermetallic Na 2 Te vs. sodiophobic baseline Cu) and electrodeposition rate affect microstructure of sodium metal and its solid electrolyte interphase (SEI). Capacity and current (6 mAh cm -2 , 0.5–3 mA cm -2 ) representative of commercially relevant mass loading in anode-free sodium metal battery (AF-SMBs) are analyzed. Synchrotron X-ray nanotomography and grazing-incidence wide-angle X-ray scattering (GIWAXS) are combined with cryogenic ion beam (cryo-FIB) microscopy. Highlighted are major differences in film morphology, internal porosity, and crystallographic preferred orientation e.g. (110) vs. (100) and (211) with support and deposition rate. Within the SEI, sodium fluoride (NaF) is more prevalent with Te-Cu versus sodium hydride (NaH) and sodium hydroxide (NaOH) with baseline Cu. Due to competitive grain growth the preferred orientation of sodium crystallites depends on film thickness. Mesoscale modeling delineates the role of SEI (ionic conductivity, morphology) on electrodeposit growth and onset of electrochemical instability.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Synergistic Tuning of Microstructure and Morphology in Carbon Molecular Sieve Hollow Fibers for Propylene/Propane Separation

Liu, Zhongyun↗

DOE OSTI2021

Relationship between microstructure evolution and properties enhancement of carbon nanotubes‐filled polybutylene terephthalate/polypropylene blends induced by thermal annealing

Abstract Thermal annealing induced microstructure evolution and properties enhancement of polybutylene terephthalate/polypropylene/carbon nanotubes (PBT/PP/CNTs) nanocomposites was methodically investigated. The electrical conductive PBT/PP/CNTs nanocomposites with a low percolation threshold were obtained by simple melt blending due to the selective location of the CNTs in PBT phase and the formation of the double percolation structure. Thermal annealing further remarkably decreased the volume resistivity of the nanocomposites, with the maximum reduction of seven orders of magnitude. Scanning electron microscope observation and rheology tests demonstrated that the relatively large CNTs agglomerates were redistributed to build more homogeneous CNTs networks after annealing. The phase coalescence during annealing promoted the formation of the more perfect co‐continuous structure. These phenomena helped to enhance the electrical conductivity of the nanocomposites. Flexural properties of the nanocomposites were also enhanced after annealing, which might be due to the more effective stress transfer between the polymer and CNTs induced by the reconstructed CNTs networks. The nanocomposites obtained in this study possess excellent electrical and mechanical properties, which can be applied to the fields of sensors, electromagnetic interference shielding, anti‐static materials, and so forth.

Shang, Mengyao↗

DOE OSTI2022

Unraveling the Photovoltaic, Mechanical, and Microstructural Properties and Their Correlations in Simple Poly(3‐pentylthiophene) Solar Cells

Abstract The power conversion efficiency of polythiophene organic solar cells is constantly refreshed. Despite the renewed device efficiency, very few efforts have been devoted to understanding how the type of electron acceptor alters the photovoltaic and mechanical properties of these low‐cost solar cells. Herein, the authors conduct a thorough investigation of photovoltaic and mechanical characteristics of a simple yet less‐explored polythiophene, namely poly(3‐pentylthiophene) (P3PT), in three different types of organic solar cells, where ZY‐4Cl, PC 71 BM, and N2200 are employed as three representative acceptors, respectively. Compared with the reference poly(3‐hexylthiophene) (P3HT)‐based solar cells, P3PT‐based devices, all perform more efficiently. Particularly, the P3PT:ZY‐4Cl blend exhibits the highest efficiency (ca. 10%) among the six combinations and outperforms the prior top‐performance system P3HT:ZY‐4Cl. Furthermore, the blend films based on N2200 exhibit a high crack‐onset strain of ∼38% on average, which is approximately 15‐ and 17‐times higher than those of ZY‐4Cl and PC 71 BM, respectively. The microstructural origins for the above difference are well elucidated by detailed grazing incidence X‐ray scattering and microscopy analysis. This work not only underlines the potential of P3PT in prolific solar cell research but also demonstrates the superior tensile properties of polythiophene‐based all‐polymer blends for the preparation of stretchable solar cells.

Polymer Science↗

DOE OSTI2022

Microstructure changes during failure of PVDF-based photovoltaic backsheets

The backsheet layer of a solar module provides a safety and environmental barrier to the high voltages running through the photovoltaic (PV) cells and electrical contacts within the core of the module. However, in the past decade, backsheet cracking has become one of the most observed failure modes in PV module field surveys. In this work, the degradation of polyvinylidene fluoride (PVDF)-based backsheets is explored. Backsheet samples are either exposed to accelerated laboratory aging (UV light, heat, and moisture) or collected from the field. Fourier transform infrared and Raman spectroscopy, fragmentation testing, atomic force and scanning electron microscopy, and small-angle neutron scattering are combined to develop an understanding of how chemistry and microstructure evolve during aging. Chemical degradation, surface pitting, polymer phase changes, and anisotropic polymer domains are all observed in aged backsheet samples. The results provide insight into the degradation mechanisms that lead to cracking and field failure of PVDF-based backsheets. The comparison of aged PVDF-based backsheets helps to lay the groundwork for limiting polymer-based failure modes in PV modules.

PVDF↗

DOE OSTI2023

Microstructural Insights into Performance Loss of High-Voltage Spinel Cathodes for Lithium-ion Batteries

Spinel-structured LiNi x Mn 2-x O 4 (LNMO), with low-cost earth-abundant constituents, is a promising high-voltage cathode material for lithium-ion batteries. Even though extensive electrochemical investigations have been conducted on these materials, few studies have explored correlations between their loss in performance and associated changes in microstructure. Here, down to the atomic scale, the structural evolution of these materials is investigated upon the progressive cycling of lithium-ion cells. Transgranular cracking is revealed to be a key feature during cycling; this cracking is initiated at the particle surface and leads to the penetration of electrolytes along the crack path, thereby increasing particle exposure to the electrolyte. The lattice structure on the crack surface shows spatial variances, featuring a top layer of rock-salt, a sublayer of a Mn 3 O 4 -like arrangement, and then a mixed-cation region adjacent to the bulk lattice. The transgranular cracking, along with the emergence of local lattice distortion, becomes more evident with extended cycling. Further, phase transformation at primary particle surfaces and void formation through vacancy condensation is found in the cycled samples. All these features collectively contribute to the performance degradation of the battery cells during electrochemical cycling.

25 ENERGY STORAGE↗

DOE OSTI2025

Zwitterionic Photocurable Resin for High‐Resolution 3D Printing of Ultralow‐Fouling Microstructures

High‐resolution 3D printing technologies are enabling a new generation of microstructured materials for applications where biocompatibility is critical. However, most conventional 3D‐printable resins yield materials that exhibit trade‐offs between antifouling properties and mechanical robustness, limiting their applicability in living systems. In nature, zwitterionic surface groups form tightly bound hydration layers that act as effective barriers against protein and cell attachment. Inspired by this strategy, a zwitterionic acrylamide‐based photoresist—carboxybetaine di‐methacrylamide (CBDA)—is developed for projection‐based vat photopolymerization, enabling the fabrication of complex microarchitectures with exceptional antifouling properties. The bifunctional monomer allows the formation of dense, cross‐linked networks that resist swelling while maintaining a high density of zwitterionic groups. Printed structures exhibit strong resistance to protein and cell adhesion, as confirmed by porcine blood assays, alongside robust mechanical performance. As a demonstration, a tubular structure featuring a negative Poisson's ratio lattice is printed to showcase structural fidelity and versatility. This resin formulation offers a broadly applicable strategy for fabricating microscale devices and surfaces where antifouling performance and structural integrity are both essential—spanning biomedical interfaces, soft robotics, and beyond.

3D printing↗

DOE OSTI2024

Influence of Rare Earth Ce Additions on Microstructure and Mechanical Properties of Experimental Pipeline Steels

Herein, the effect of Ce additions ranging from 57 to 263 ppm is evaluated for an experimental pipeline steel. Compared to the Ce-free steel, progressive Ce additions result in a slightly refined microstructure, significantly improve transverse impact properties, and slightly increase strength. All these observations can be attributed to the gradual transformation of Mn sulfide and Mn–Si–Al oxide inclusions to Ce-containing oxide/sulfides. In particular, the inclusions consist exclusively of sub-5 μm spherical Ce 2 O 2 S particles upon near-stoichiometric additions of Ce, considering the oxygen and sulfur impurity level of the steel. In conclusion, the results suggest that Ce is a potentially promising alloying addition for next-generation pipeline steels by replacing overtly deleterious inclusions with potentially beneficial ones.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Improving the Mechanical Properties of Cast Aluminum Via Ultrasonication-Induced Microstructural Refinement

One barrier to the broader use of cast aluminum alloys in automotive applications is their poor mechanical properties, especially compared to wrought materials. This study investigates the use of ultrasound to refine the microstructure of cast aluminum alloys during solidification and thus improve their mechanical properties. An A356 aluminum alloy (Al-Si-Mg) with added Fe (to mimic a recycle-grade alloy) was cast in a graphite mold with the simultaneous application of ultrasound. Tensile specimens were extracted from the castings and heat treated to a T6 temper. Ultrasonication during casting transformed the morphology of primary aluminum grains from dendritic (~140 microns in size) to globular (~36 microns in size), increased the ultimate tensile strength by 10 %, and tripled the ductility compared to casting without ultrasound. This improvement in strength and ductility demonstrates the potential for ultrasonic processing to improve the performance of cast aluminum alloys without altering their chemistry or additional post-processing.

Aluminum, Solidification, Ultrasound, Grain refinm↗

DOE OSTI2023

Tailoring the γ-γ'-γ" dual superlattice microstructure of INCONEL® 725 by high temperature aging and Nb/Ta additions for superior creep properties

Next-generation energy systems require superior resistance to creep deformation due to the considerably prolonged exposure times at operating stress and temperature. To improve the elevated temperature properties of INCONEL® 725 (IN725), a corrosion resistant alloy, several variants with different Ti/Al ratio and judicious amounts of Nb and Ta were made. Furthermore, a high temperature aging (HTA) heat treatment, designed to promote favorable precipitate phase formation, was explored. These adjustments allowed to tailor the amount and type of precipitate strengthening which led to significant increases in time to failure. The Ti/Al ratio was used to favor the formation of γ' or γ" precipitates. Compact morphology precipitates, consisting of γ' precipitates surrounded by a γ" shell, were formed in alloys with a low Ti/Al ratio. The HTA increased the creep life of various alloy formulations up to a maximum improvement of 371% as compared to the standard aging heat treatment. The Nb and Ta additions had a similar effect on increasing creep life by promoting and stabilizing γ" precipitation. The positive effect of the additions was even more pronounced when coupled with the HTA. A phase stability study with up to 10,000 h exposure at 700°C revealed that the compact morphology helped in slightly reducing coarsening of the γ' precipitates, although the effect on creep was not significant. The findings of this study enable design of dual superlattice alloys through microstructural engineering that yields superior performance and can be applied to a wide range of alloys in the IN718 and derivatives family.

Antonov, Stoichko↗

DOE OSTI2024

Microstructural evolution in a precipitate-hardened (Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 ) 94 Ti 2 Al 4 multi-principal element alloy during high-pressure torsion

Multi-principal element alloys demonstrate high strength, thermal stability, and irradiation resistance, making them excellent candidate materials for applications in nuclear reactors and other harsh environments. Some studies have examined the use of high-pressure torsion to strengthen MPEAs through grain size reduction and strain hardening. However, no studies have investigated the effect of HPT on secondary phases (precipitates) within an MPEA. Two alloys, (Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 ) 94 Ti 2 Al 4 containing Ni(Ti, Al) B2 phase, and CrFe σ phase, and single-phase Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 , were fabricated by casting and heat treatment. Both alloys were then processed with HPT to study microstructural evolution. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to characterize the alloys before and after HPT processing. HPT processing produced a nanocrystalline structure in both alloys, but (Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 ) 94 Ti 2 Al 4 exhibited a significantly smaller grain size and higher dislocation density than Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 , with corresponding higher hardness. Before HPT, the (Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 ) 94 Ti 2 Al 4 alloy consisted of large grain (~ 400 μm) and precipitates, including B2 of ~ 38 μm average size, B2 of ~ 0.7 μm average size, and small amounts of σ of ~ 1.5 μm average size. After HPT, the larger B2 precipitates were decreased in size and volume fraction, while the smaller B2 precipitates were completely dissolved; the σ precipitates appeared unaffected by HPT, likely due to their much higher hardness. Finally, observation of the B2 precipitate distribution along radial distance indicates that the strain caused the precipitates to fracture at intermediate strain (γ = 125) and dissolve at high strain (γ = 280).

36 MATERIALS SCIENCE↗

DOE OSTI2023

Effect of Volumetric Energy Density on Microstructure and Properties of Grade 300 Maraging Steel Fabricated by Laser Powder Bed Fusion

Here this study investigated the effect of laser powder bed fusion process parameters on the microstructure and properties of maraging steel. The results show that the process parameters can be finetuned to achieve both a high build rate/low hardness and low build rate/high hardness during fabrication, enabling the co-design of components where property gradients are desirable such as an injection molding tool where surface hardness is desired to be higher than the bulk, which needs to have higher fracture toughness.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Comparative Analysis of Austenitized Steel Microstructures Due to Induction and Conventional Heating in High Magnetic Field

While magnetic field-assisted processing shows promise in improving alloys’ mechanical properties, insufficient descriptions of heating methods hinder development of tailored processing pathways. This study investigates how induction and conventional heating affect microstructures of near-eutectoid Fe–C steel with and without 9 T magnetic field. Conventionally heated samples in field showed more austenite grain growth compared to inductively heated counterparts. Annealing twin frequency increased under field, with twin density increases not fully explained by larger grain sizes.

Hurley, Megan [University of Florida, Gainesville]↗

DOE OSTI2025

Phase equilibria and microstructure evolution in the Ni-rich region of binary Ni-Ce and ternary Ni-Ce-X (X=Al, Nb, Cr, Ti) systems at 900 °C

The equilibrium compositions of all phases in the Ni-rich region of binary Ni-Ce and ternary Ni-Ce-X (X=Al, Nb, Cr, Ti) systems at 900 °C were determined experimentally through isothermal annealing for up to 500 h and compared with currently available computational thermodynamic descriptions. Additionally, the study examined how adding a third element to the binary system affects the microstructure by analyzing changes in the volume fraction of the intermetallic phase in the eutectic region. It was observed that Nb and Ti addition lowered the intermetallic fraction in the eutectic region while Al and Cr addition did the opposite. The fraction of intermetallic phase in the eutectic region is very important because it contributes to extreme brittleness of these alloys. Also, Al, Nb and Ti addition promoted different precipitates upon annealing when added in sufficient amounts. The collected data on composition and phase equilibria provides crucial information for improving the thermodynamic assessments of the binary and ternary alloy systems.

energy dispersive spectrometry↗

DOE OSTI2019

Microstructure and mechanical properties of pure copper wire produced by shear assisted processing and extrusion

Shear assisted processing and extrusion (ShAPE) process can consolidate powdered materials and simultaneously extrude wire or tube with improved properties. We successfully produced copper wire extrusions from powder and solid materials for the first time. The extrusion pressure of ShAPE process is at least two times less than that required for conventional extrusion. We used optical microscopy to inspect and validate the integrity of extrudates. It shows that the microstructure was refined and dynamically recrystallized to equiaxial grains. Compared to the annealed copper wire, ShAPE processed wire has 80% higher yield strength, 15% higher ultimate tensile strength and 20% higher ductility. These were correlated with refined grain size and sub-structuring observed via electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM).

Copper, Wire, Shear Assisted Processing and Extrus↗