SEARCH · Engineering Papers

Results for “water evaluation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Assessing the impacts of wakes on floating wind farms with shared anchors

This paper examines wake effects for floating wind farms with shared anchors. Three 20-turbine farms are examined: a grid-formation baseline with no shared anchors, a farm based on 3-line anchors, and a farm based on 6-line anchors, governed by a wind turbine spacing of 8 rotor diameters. The IEA 15 MW reference turbine on the UMaine semisubmersible platform was used with a taut mooring system in deep- water depths representative of U.S. west coast lease areas. A steady-state wake model showed that, when evaluating a sweep of wind headings, the baseline design had the lowest wake losses, with a value of 11.7 %, followed by the 6-line at 12.9% and the 3-line at 13.8%. Dynamic simulations were run in FAST.Farm to analyse the effects of wakes on mean anchor loads for wind headings that showed significant wake losses. The baseline farm showed the largest anchor load reductions due to wake effects (up to 16%), followed by the 3-line farm (up to 8%), and the 6-line farm, which showed relatively consistent load magnitudes on the 6-line anchors across all headings.

17 WIND ENERGY↗

DOE OSTI2024

Wet-Etching of Acoustically Spalled GaAs for Substrate Reuse

Acoustic spalling is a promising technique for substrate reuse in the fabrication of gallium arsenide (GaAs) photovoltaic cells. However, the acoustic spalling process can leave the substrate with areas of rough surface morphology that can interfere with subsequent cell growth and processing. In this work, we investigate the use of wet etchants to smooth the surface of acoustically spalled GaAs substrates. We evaluated six different etchants. Of those tested, an 8:1:1 mixture of sulfuric acid, hydrogen peroxide, and water at 30 degrees C and a moderate stirring rate showed the greatest roughness reduction per mass loss while producing the desired morphology. This etchant was then applied to an acoustically spalled 2-inch GaAs wafer. A single-junction GaAs cell was then grown via metalorganic vapor-phase epitaxy on this substrate, an acoustic spalled substrate without a smoothing etch, and an epi-ready substrate. Use of the 8:1:1 H2SO4:H2O2:H2O etchant produced cells an average efficiency of 12.8% as compared to that of 2.0% grown on the unetched acoustically spalled substrate and 16.3% grown on the epi-ready substrate. The results of this work demonstrate that wet etching is a viable method for smoothing the surface of spalled GaAs substrates, paving the way for substrate reuse via acoustic spalling at efficiencies that approach growth on epi-ready substrates.

etching↗

DOE OSTI2023

Modeling strategies and data needs for representing coastal wetland vegetation in land surface models

Vegetated coastal ecosystems sequester carbon rapidly relative to terrestrial ecosystems. Coastal wetlands are poorly represented in land surface models, but work is underway to improve process-based, predictive modeling of these ecosystems. Here, in this work, we identify guiding questions, potential simulations, and data needs to make progress in improving representation of vegetation in terrestrial–aquatic interfaces, with a focus on coastal and estuarine ecosystems. We synthesize relevant plant traits and environmental controls on vegetation that influence carbon cycling in coastal ecosystems. We propose that models include separate plant functional types (PFTs) for mangroves, graminoid salt marshes, and succulent salt marshes to adequately represent the variation in aboveground and belowground productivity between common coastal wetland vegetation types. We also discuss the drivers and carbon storage consequences of shifts in dominant PFTs. We suggest several potential approaches to represent the diversity in vegetation tolerance and adaptations to fluctuations in salinity and water level, which drive key gradients in coastal wetland ecosystems. Finally, we discuss data needs for parameterizing and evaluating model implementations of coastal wetland vegetation types and function.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2021

Isotopic and Fuel Lattice Parameter Trends in Extended Enrichment and Higher Burnup LWR Fuel Vol I: PWR fuel

Commercial light water reactor (LWR) operators and fuel vendors in the United States are pursuing changes to nuclear fuel that include extended enrichment (EE) and accident-tolerant fuel (ATF) designs. The term EE (8% > 235 U > 5%) is used in this report to refer to a subset of high assay low-enriched uranium (HALEU) that is considered usable in commercial US LWRs in the near term. ATF features are designed to improve fuel system performance under accident conditions. One goal of EE is to improve fuel cycle economy by enabling fuel to be depleted to higher burnup than the typical current maximum pin burnup limits (62 gigawatt-days per metric ton of uranium [GWd/MTU]). Adoption of EE, ATF, and high burnup (HBU) fuels in the US commercial fleet requires a clear understanding of the effects on core physics parameters and used fuel isotopic content, as well as confidence in the accuracy of computer code predictions over an expanded range of materials, enrichment, and burnup. A thorough understanding of the applicability and adequacy of benchmark data (e.g., criticality, decay heat, isotopic content) for computer code validation is necessary to ensure that appropriate safety margins are maintained. To prepare for and support these potential changes, the effects of EE, ATF, and HBU are being assessed for selected representative LWR fuel designs. The project is divided into phases: this report summarizes the findings of Phase 1, which focuses on the lattice physics parameter and used fuel isotopic changes for a conventional Westinghouse 17×17 pressurized water reactor (PWR) design. The primary investigation tool is the SCALE Polaris code using the SCALE 56-group Evaluated Nuclear Data File (ENDF)/B-VII.1 cross sections. The goal of the current work is to (1) identify and explain important effects of EE and HBU (reactivity, lattice physics, and isotopic effects) assuming that PWR fuel design and usage remain similar to those for current enrichment fuel, (2) provide limited code-to-code comparisons with higher order cross section libraries and/or codes, and (3) identify any apparent anomalous trends in the results for further investigation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

Sequim Bay Underwater UXO Prototype Demonstration Site: Field Operations Summary, 2020

This report provides a summary of Pacific Northwest National Laboratory’s (PNNL’s) activities to initiate Phase II development of the Sequim Bay Underwater UXO Prototype demonstration site (MR-2735) in 2020. Testbed development and field operations were conducted by PNNL’s Coastal and Marine Research Laboratory (MCRL) in support of the Strategic Environmental Research and Development Program (SERDP) and Environmental Security Technology Certification Program (ESTCP) underwater Munitions Response (MR) program. A series of standardized underwater unexploded ordnance (UXO) demonstration sites (“testbeds”) are being developed by SERDP/ESTCP to test, evaluate, and demonstrate technologies that can detect, geolocate, and classify proud and buried munitions in 0–35 m water depths. As a prototype demonstration site, Sequim Bay is a semi-enclosed marine waterbody containing sand and mud sediments with minimal clutter in 5–30 m water depths. MCRL is located at the entrance to Sequim Bay, where it provides operational, logistical, and facilities support for testbed activities.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

DOE OSTI2021

Characterization of Offshore Storage Resource Potential in the Central Planning Area of the Gulf of Mexico

This report contains a brief overview of the several studies that provide the basis for this work and details the reservoir characterization efforts that have been completed to date. Briefly, geological characterization data suggests that the deep-water reservoirs are the result of the interplay between turbidite depositional systems and salt tectonics. Project Partners have estimated the CO 2 storage capacity associated with saline reservoirs and that associated with CO 2 -Enhanced Oil Recovery (EOR) in the state waters of Louisiana. In addition, Project Partners have conducted a detailed analysis of CO 2 storage potential associated with CO 2 -EOR in the central planning area of the GOM. This work estimates that 3,140 million metric tonnes of CO 2 can be stored in optimal reservoirs of the shallow- and deep-water central GOM. A reduced order modeling and machine learning approach is introduced that will be used to evaluate CO 2 storage capacity and plume dynamics for down-selected, reservoir-specific, saline characterization. Last, a brief discussion establishes how the data presented in this report will support future work.

02 PETROLEUM↗

DOE OSTI2023

Comparison of Tritium Dose Calculations from MACCS, UFOTRI, and ETMOD

Tritium exhibits unique environmental behavior because of its potential interactions with water and organic substances. Modeling the environmental consequences of tritium releases can be relatively complex and thus an evaluation of MACCS is needed to understand what updates, if any, are needed in MACCS to account for the behavior of tritium. We examine documented tritium releases and previous benchmarking assessments to perform a model intercomparison between MACCS and state-of-practice tritium-specific codes UFOTRI and ETMOD to quantify the difference between MACCS and state of practice models for assessing tritium consequences. Additionally, information to assist an analyst in judging whether a postulated tritium release is likely to lead to significant doses is provided.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

DOE OSTI2024

Baselining the Indirect Effect by Improving Quantification of Sea Spray and Marine Sources at Ascension Island (Final Report)

Oceans cover two-thirds of the Earth and understanding the interactions of aerosols with clouds in these large marine regions requires quantifying the man-made contributions to the budget of cloud-drop forming particles (known as cloud condensation nuclei, or CCN) relative to the non-manmade “baseline” conditions and understanding the meteorology of boundary layer clouds. Modeling studies have shown substantial uncertainties and sensitivities to natural marine CCN sources, meaning that to reduce uncertainties in indirect effects we must be able to better quantify the CCN budget in ocean regions. While models provide important constraints on these uncertainties, actually reducing uncertainties requires substantial observations in open-ocean and coastal regions in order to establish the baseline on which manmade emissions are added. The tropical South Atlantic Ocean is one of the least-sampled regions of the planet, making the comprehensive measurements of the Department of Energy Atmospheric Radiation Measurement Layered Atlantic Smoke Interactions with Clouds (LASIC) campaign provides the longest record of aerosol size distribution measurements from a differential mobility analyzer in a cloud-influenced marine location in the ARM database, with 17 months of ground-based aerosol size distribution measurements. This project addressed the research topic of Aerosol-Cloud Interactions (ACI) by supporting three publications from the LASIC measurements: 1. The ARM measurements were combined with a new value-added technique that was pioneered by the Russell group for quantifying sea salt. This quantification of sea salt uses supermicron scattering measurements for retrieving reasonable sea spray mass concentrations, providing the best-available, observationally-constrained estimate of the sea spray mode properties when supermicron size distribution measurements are not available. 2. The fitted modes of the distribution were used to investigate the signatures of cloud processing for very clean to very smoky aerosol conditions, revealing not only differences in the particles that activate in clouds but also in the mechanisms that control that droplet formation process. In clean air, the size required to form a cloud droplet is influenced by the number of particles, as well as how quickly particles take up water during growth in cloud. 3. Building on this aerosol characterization, cloud and meteorological conditions were used to evaluate aerosol-related changes in cloud albedo and optical depth. We introduced a new method of decomposing the impact of aerosols on clouds known as the Twomey effect by incorporating retrieved supersaturation from two independent sets of observations to constrain the feedback of aerosol particles on cloud properties. The method quantifies the reduction of the Twomey effect at high aerosol concentrations, which has never been explained quantitatively by observations. In addition, the results provide the first direct validation for the conditions observed in the tropical South Atlantic of a parcel-based approach that is embedded in many climate models. Together these findings illustrate how ARM extended field campaigns in stratocumulus-covered regions can be used to constrain ACI processes with direct observations, providing specific radiative effects without models. By making such process-specific constraints available to improve ACI in global climate models, ARM observations play a key role in supporting model development.

58 GEOSCIENCES↗

DOE OSTI2024

A Field-Deployable Magnetic Resonance Imaging Rhizotron for Modeling and Enhancing Root Growth and Biogeochemical Function

A collaborative team from Texas A&M AgriLife Research, ABQMR Inc., the Soil Health Institute, the Athinoula A. Martinos Center for Biomedical Imaging, and NIST developed low-field magnetic resonance imaging (LF-MRI) instrumentation capable of imaging intact soil-root systems. The system measured root biomass, architecture, 3D mass distribution, and growth rates, providing a non-destructive means to evaluate ideal plant characteristics based on root metrics. It also successfully generated three-dimensional images of soil water content, a key property influencing root growth and exploration. Operating much like an MRI used in a medical setting, the system functioned in field conditions without damaging plants, overcoming the limitations of traditional methods such as trenching, soil coring, and root excavation. Over the course of the project, the team designed and built three functional prototype systems. These prototypes provided new insights into root–water–soil interactions that drive processes such as nutrient uptake, water use, and carbon management. This information contributed to efforts to optimize plants for carbon sequestration without sacrificing economic yield. The project also supported the identification of desirable traits for energy sorghum, including high root growth rates, more vertical root angles, and enhanced drought resilience under water-limiting conditions.

09 BIOMASS FUELS↗

DOE OSTI2023

Impact of Oxygen Storage Components in Prototype Pd-Based Three-Way Catalysts under Exhaust Conditions Relevant to Propane Engines

With increasing concerns about global warming, the push for sustainable and eco-friendly fuels is accelerating. Propane, recognized as liquefied petroleum gas or LPG, has garnered research interest as an alternative fuel due to its notable advantages, including a high-octane rating, reduced greenhouse gas emissions, and potential cost-effectiveness. However, to realize its full potential as an alternative fuel it is essential to develop catalysts that efficiently handle emissions at low temperatures. In our research, we investigated three distinct palladium (Pd)-based three-way catalyst (TWC) formulations (PdRh, Pd-only, and Pd-OSC) to investigate the influence of typical TWC components rhodium (Rh) and oxygen storage components (OSC) in exhaust scenarios relevant to propane-fueled engines. Among these, the formulation containing oxygen storage components (Pd-OSC) showed the highest reactivity for both NO and C 3 H 8 while minimizing performance degradation from hydrothermal aging (HTA). Notably, the temperature of 50% conversion (T50) for propane in the Pd-OSC fresh and HTA sample was lower by 30 °C and 13 °C, respectively, compared to the Pd-only sample, highlighting the role of oxygen storage materials in enhancing catalyst performance, even without dithering. Additionally, N 2 physisorption showed that the PdOSC sample has a higher surface area and increased pore volume. This underscores the idea that OSC materials not only augment the catalyst’s porosity but also optimize reactant accessibility to active sites, thus elevating catalytic efficiency. In addition to evaluating performance, we further explored the performance and characteristics of the catalysts using catalytic probe reactions, such as water–gas shift and steam reforming reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Feasibility of Ocean-Based Renewable Energy in the Gulf of Mexico

This paper summarizes a comprehensive feasibility assessment of six offshore renewable energy sources in the Gulf of Mexico (GOM) to potentially provide utility-scale electricity from the Outer Continental Shelf (federal waters) and state waters to land-based grids. Overall, the primary objective is to inform future energy planning. The authors evaluated offshore wind, wave energy, tidal energy, ocean-based solar photovoltaics (PV), ocean current, and ocean thermal energy conversion. Of these energy resources, offshore wind was the most viable option and was the focus of the second part of the study. The technical challenges of developing offshore wind in the GOM are discussed including hurricane design for turbines and substructures, as well as turbine solutions to overcome lower wind regimes. In addition, advantages to offshore wind development in the GOM are described including proximity to oil and gas supply chains. Economic analysis using established cost models at the National Renewable Energy Laboratory identified hypothetical project locations where net value of offshore wind was the highest, and the levelized cost of energy (LCOE) was calculated for three sites: Port Isabel, Port Arthur, and Pensacola. Offshore wind LCOE in the GOM was found to be higher than those in sites along the north and mid-Atlantic coasts, but decreasing cost trajectories indicate the possibility of economic viability for locations in Texas and west Louisiana after 2030. The extrapolated 2030 LCOE values range from 73 dollars per MWh (Site 1, Port Isabel) and 79 dollars per MWh (Site 3, Port Arthur) to 91 dollars per MWh (Site 5, Pensacola).

16 TIDAL AND WAVE POWER↗

DOE OSTI2020

ISR Restoration Methods and Applicability to Groundwater Remediation at Abandoned Uranium Mills - 20342

There are numerous abandoned uranium mining and mill sites in the southwestern US. Surface remediation was undertaken in the 1980's and 90's to cover mill tailings and minimize infiltration of meteoric precipitation into the subsurface These actions have reduced the availability of tailings contaminants but many of these sites have persistent groundwater contamination, primarily due to the disposal of tailings and process fluids in unlined impoundments during the mill's operational life. Active in situ recovery (ISR) uranium mining and wellfield restoration practices are examined to determine the factors that contribute to the success of groundwater restoration. Hydrologic characteristics, geochemistry, ore body quality, regulatory requirements and the aboveground components of uranium production and water treatment are considered. While there is no such thing as a typical abandoned mill site, the potential use of ISR restoration methods is evaluated for viability as a remedial alternative to mine and mill sites that have residual contaminated groundwater plumes. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2025

Enhancing heat pump water heater performance with embedded phase change materials thermal energy storage: First hour rating improvement and demand response operation

The increasing global emphasis on energy efficiency and sustainability has put heat pump water heaters (HPWHs) in the spotlight as an energy-efficient alternative to traditional water heating systems. However, their widespread adoption is limited by challenges such as insufficient First Hour Rating (FHR), suboptimal control mechanisms, and limited flexibility for demand response operations. Here, to address these limitations, this study proposes an innovative HPWH system integrated with embedded phase change material (PCM)-based thermal energy storage (TES). The research introduces a novel design and control strategy that leverages optimized PCM integration to enhance thermal storage capacity, improve hot water delivery during peak demand, and increase load-shifting potential. A combination of system modeling, performance simulation, and demand response control strategy evaluation was employed to quantify the benefits of PCM integration. Results demonstrate that the proposed PCM-TES HPWH system significantly enhances FHR, with an optimal 7.0 lb. of PCM increasing FHR by over 26 %—from 62 to 78 gal—for a standard 50-gal HPWH. Additionally, under advanced demand response operation using a preheat strategy, the system reduces the percentage of control temperature out-of-band time from 65 % (conventional HPWH) to just 11.6 %, enabling a more stable and efficient hot water supply. This research contributes a novel PCM-embedded HPWH design and control framework that addresses both performance and grid-interactivity challenges. The findings offer a viable pathway to enhancing the operational efficiency, flexibility, and grid responsiveness of residential water heating systems.

Demand response control↗

DOE OSTI2025

CMIP6-based Multi-model Hydropower Projection over the Conterminous US, Version 1.1

This dataset presents a suite of hydropower projections for the conterminous United States (CONUS), derived from multiple downscaled and bias-corrected Global Climate Models (GCMs) from the Coupled Model Intercomparison Project Phase 6 (CMIP6). The CMIP6 GCMs are downscaled using either statistical (DBCCA) or dynamical (RegCM) approaches, based on two meteorological reference datasets (Daymet and Livneh). The resulting downscaled precipitation, temperature, and wind speed data are then used to drive two calibrated hydrologic models (VIC and PRMS), enabling simulations of projected future hydrologic responses across the CONUS. Simulated total runoff is subsequently employed to drive two hydropower models (WMP, now implemented as mosartwmpy-power, and WRES) to evaluate how climate change may affect future hydropower production for both federal and non-federal hydropower fleets. This dataset was developed to support the SECURE Water Act Section 9505 Assessment for the U.S. Department of Energy (DOE) Water Power Technologies Office (WPTO). For further details, see Broman et al. (2024), Thurber et al. (2024), Kao et al. (2022), and Zhou et al. (2023).

Voisin, Nathalie [Pacific Northwest National Labor↗

DOE OSTI2022

Coreflood Tests to Evaluate Enhanced Oil Recovery Potential of Wettability-Altering Surfactants for Oil-Wet Heterogeneous Carbonate Reservoirs

Summary Oil-wetness and heterogeneity are two main factors that result in low oil recovery (OR) by waterflood in carbonate reservoirs. The injected water is likely to flow through high-permeability regions and bypass the oil in the low-permeability matrix. In this study, systematic coreflood tests were carried out in both “homogeneous” cores and “heterogeneous” cores with a wettability-altering surfactant. The homogeneous coreflood tests were conducted to evaluate surfactant retention, as well as to compare tertiary surfactant flooding with secondary surfactant flooding. The heterogeneous coreflood test was proposed to model bypassing in low-permeability matrix during waterfloods, and dynamic imbibition of surfactant into the low-permeability matrix. Surfactant retention results suggest that retention increases as initial oil saturation decreases. The retention of selected surfactant in the target reservoir cores was measured to be within a range of 0.07–0.12 mg/g-rock, which is economically acceptable. The results of homogeneous coreflood tests showed that both secondary waterflood and secondary surfactant flood can achieve high OR (>50%) from relatively homogeneous oil-wet cores. A shut-in phase after the surfactant injection resulted in a surge in oil production, which suggests that enough time should be given for wettability alteration by surfactants. The results of heterogeneous coreflood tests showed that more oil is bypassed in the tighter matrix by waterflood if the permeability is higher in the flooded layer and this bypassed oil is the target for the wettability-altering surfactant floods. Slow wettability-altering surfactant injection leads to imbibition into bypassed regions. When the oil-wet carbonate reservoirs have large unswept regions after waterflood, wettability-altering surfactants can significantly improve OR if enough time is given for imbibition.

Engineering↗

DOE OSTI2023

Microstructural Characterizations of Two High Fluence Baffle-Former Bolts Retrieved from a Westinghouse Two-loop Downflow Type PWR

As one of the pressurized water reactor (PWR) internal components, baffle-former bolts (BFBs) are subjected to significant mechanical stress and neutron irradiation from the reactor core during the plant operation. Over the long operation period, these conditions lead to potential degradation and reduced load-carrying capacity of the bolts. In support of evaluating long-term operational performance of materials used in core internal components, the Oak Ridge National Laboratory (ORNL), through the Department of Energy (DOE), Office of Nuclear Energy, Light Water Reactor Sustainability (LWRS) Program, Materials Research Pathway (MRP), has harvested two high fluence BFBs from a commercial Westinghouse two-loop downflow type PWR. The two bolts of interest, i.e. bolts # 4412 and 4416, were withdrawn from service in 2011 as part of a preventative replacement plan. No identification of cracking or potential damage was found for these bolts during their removal in 2011. However, the bolts required a lower torque for removal from the baffle structure than the original torque specified during installation. Irradiation damage levels in the bolts range from 15 to 41 displacements per atom. The goal of this project is to perform detailed microstructural and mechanical property characterization of BFBs following in-service exposures. The information from these bolts will be integral to the LWRS program initiatives in evaluating end of life microstructure and properties. Furthermore, valuable data will be obtained that can be incorporated into model predictions of long term irradiation behavior and compared to results obtained from experimental reactor conditions

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2020

A Particle-Based Conditional Sampling Scheme for the Simulation of Transport in Fractured Rock With Diffusion Into Stagnant Water and Rock Matrix

In situ experiments and field-scale characterization studies have pointed out that, in fractured crystalline media, groundwater flow is highly channelized. This implies that, at the scale of a single fracture, only part of the fracture surface area is in contact with flowing water, while the rest of in-plane water is essentially stagnant and can be accessed by solutes via molecular diffusion. Despite their importance for contaminant retention, to date, there are no numerical or analytical approaches that could be used to assess the implication of stagnant water zones on solute transport in realistic large-scale Discrete Fracture Network-based models. In this study, we present an efficient and flexible algorithm for the simulation of transport in fractured rock with diffusion into stagnant water and rock matrix. The algorithm is a generalization of a previously developed numerical framework for time domain particle tracking in sparsely fractured rock. The key of the generalization is that total time in fracture (τ f ) is first evaluated using a Monte Carlo sampling and then a second sampling is performed conditioned on τ f . The algorithm has been successfully validated against existing independent solutions and the implication of diffusion into stagnant water and secondary diffusion into the matrix has been assessed for a realistic modeling scenario. The results show that, due to diffusion into stagnant water, contaminants are more strongly retarded. This increased retention is more significant for sorbing species, as a larger number of sorption sites is accessible. A high sensitivity to the flowing channel/stagnant water zone geometry has also been observed.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2024

Fitness-for-Service Analysis of Reactor Components under Flexible Load-Following Operating Conditions

Conventional power-generation plants, including nuclear plants, have been traditionally designed to provide a steady baseload energy capacity, optimizing output efficiency while minimizing variable costs. However, the growing adoption of large-scale renewable energy-generation systems, which rely on intermittent sources such as solar and wind, has introduced more variability into the energy supply in interconnected electricity grids. As a result, the next generation of power plants needs to operate in what is known as the load-following mode, requiring flexible adjustments in electricity production to align with the energy demand on the grid. This transition from the steady baseload operation to load-following operating conditions can significantly increase the number of times various plant components are exposed to transient stresses. This increased thermo-mechanical cycling can lead to accelerated material degradation, thereby elevating the risk of premature failure of a component. It becomes imperative to conduct a comprehensive analysis of fatigue, creep-fatigue, and stress corrosion cracking life, to assess the resilience of the various engineering components under these flexible load-following operating conditions. This study aims to develop a comprehensive numerical model of a light-water reactor pressure vessel (RPV) to investigate its degradation under various operating scenarios. This coupled thermo-mechanical finite element analysis evaluated the stress response of the RPV caused by considering fluctuations in thermal and mechanical loads caused by the varying pressure and temperature occurring during the load-following operation. Critical locations on the RPV are subsequently identified based on the stress response. The stress intensity factors for the postulated flaws at those locations are then calculated, followed by an evaluation of the reactor's life in accordance with the ASME Boiler and Pressure Vessel Code Section XI. This comprehensive life assessment covers a number of transients expected during the flexible load-following operation, providing invaluable insights into the RPV's structural integrity. Moreover, the development methodology can be adapted to other reactor components, as well as components of conventional power stations that are affected by varying operating conditions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗