Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “synchrotrons”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Transport of coexisting Ni-Cu sulfide liquid and silicate melt in partially molten peridotite

Transport of coexisting sulfide and silicate melts in partially molten peridotite contributes to the redistribution of chalcophile elements within the upper mantle as well as the genesis of magmatic Ni-Cu sulfide deposits, but has not been investigated systematically. Using laboratory experiments, theoretical calculations, and X-ray synchrotron microtomography, this study documents the topology and considers controls on the extraction of two immiscible liquids during partial melting of mantle peridotite. Under hydrostatic conditions, the measured dihedral angle at silicate melt-mineral-mineral junctions is 13.7–21.3°. Silicate melt is distributed along grain edges forming incompletely interconnected melt channels that disconnected by some dead ends at melt fractions ~7–9 vol%. Application of theoretically predicted permeability (k ~10 -14 -10 -16 m 2 ) permits estimation of the extraction velocity of silicate melt of 0.7-11.1 μm/day within a single interconnected melt channel. In the absence of silicate melt, isolated sulfide droplets (3.77 vol%) show a sulfide-olivine-olivine dihedral angle of 91.5–101.3°. However, in the presence of silicate melt, sulfide droplets (average size ~2.53±2.14μm, 1σ) are partially surrounded by silicate melt and stranded in triple junctions or melt pockets due to the limitation of the smallest dimension (0.3μm) of melt channels. Thus, the extraction of sulfide liquid is highly restricted by these dead ends and the smallest dimension of melt channels during porous flow of silicate melt. In contrast, during large-strain shear deformation (strain ~1.6–2.5), initially stranded sulfide droplets were elongated and extracted with silicate melt into liquid-rich sheets with a length of several hundred microns, constantly oriented at 14.3±4.5°to the shear plane and antithetic to the shear direction. The angle is lower than that (18-30°) of those sheets containing sulfide liquid only, indicating that silicate melt dominates liquid-rich sheets. Driven by stress, silicate melt-dominated liquid-rich sheets open the appropriately oriented grain boundaries between silicate minerals, thus providing an efficient pathway for the extraction of sulfide liquid during deformation. When such sheet-like channels remain open, sulfide droplets (> millimeter-scale) can be potentially mobile through high strain domains of the upper mantle, contributing to the addition of chalcophile elements and the fertilization of the lithospheric mantle.

high P-T experiment↗
DOE OSTI2021

Dynamic in situ imaging of methane hydrate formation in coal media

Fast 3D X-ray imaging has proved to provide crucial insights into multi-phase dynamic processes in various geomaterials. In particular, many in situ imaging experiments have been made to study gas-hydrate formation in porous sandy samples. Such imaging is challenging for the methane gas-hydrate formation in coal samples because of the coal micro-porosity structure and lower X-ray contrast. Here we present results of the first dynamic in situ micro-computed tomography experiment of methane-hydrate formation in coal samples. Synchrotron phase-contrast tomography techniques allowed to achieve necessary contrast levels to separate all the materials of interest (gas, water, coal, and gas hydrate) in reconstructed images with high spatial and temporal resolution. The imaging results are compared to the ones from a similar tomographic experiment with sand samples. Methane-hydrate formation is accompanied by the water movements caused by cryogenic water suction that happens in sequences of short fast movements with longer equilibrium states in between. Only one type of the hydrate formation was observed in coal (growth as shells on grain boundaries) as opposed to three types in sand (shells, growth into gas pockets, and inside water volumes). In particular, this leads to a slower hydrateformation speed in coal. For the coal sample, we also observed water extraction from grains, and interpreted it as competitive sorption of methane. Lastly, we visualized the dynamic behavior of this water extraction via microchannels inside the coal grains, and performed nano-tomography imaging of these channels for a better understanding of this phenomenon.

58 GEOSCIENCES↗
DOE OSTI2024

X-ray fluorescence and XANES spectroscopy revealed diverse potassium chemistries and colocalization with phosphorus in the ectomycorrhizal fungus Paxillus ammoniavirescens

Ectomycorrhizal (ECM) fungi play a major role in forest ecosystems and managed tree plantations. Particularly, they facilitate mineral weathering and nutrient transfer towards colonized roots. Among nutrients provided by these fungi, potassium (K) has been understudied compared to phosphorus (P) or nitrogen (N). The ECM fungus Paxillus ammoniavirescens is a generalist species that interacts with the root of many trees and can directly transfer K to them, including loblolly pine. However, the forms of K that ECM fungi can store is still unknown. Here, we used synchrotron potassium X-ray fluorescence (XRF) and K-edge X-ray Absorption Near Edge Structure (XANES) spectroscopy on P. ammoniavirescens growing in axenic conditions to investigate the K chemistries accumulating in the center and the edge of the mycelium. We observed that various K forms accumulated in different part of the mycelium, including K-nitrate (KNO 3 ), K-C-O compounds (such as K-tartrate K 2 (C 4 H 4 O 6 ) and K-oxalate (K 2 C 2 O 4 )), K-S and K-P compounds. Saprotrophic fungi have been shown to excrete carboxylic acids, which in turn play a role in soil mineral weathering. Our finding of several K counter-ions to carboxylic acids may suggest that, besides their direct transfer to colonized roots, K ions can also be involved in the production of compounds necessary for sourcing nutrients from their surrounding environment by ECM fungi. Additionally, this work reveals that XANES spectroscopy can be used to identify the various forms of K accumulating in biological systems.

Ectomycorrhizal symbiosis↗
DOE OSTI2022

Revealing melt flow instabilities in laser powder bed fusion additive manufacturing of aluminum alloy via in-situ high-speed X-ray imaging

Laser metal additive manufacturing technologies enable the fabrication of geometrically and compositionally complex parts unachievable by conventional manufacturing methods. However, the certification and qualification of additively manufactured parts are greatly hindered by the stochastic melt flow instabilities intrinsic to the process, which has not been explicitly revealed by direct observation. Here, we report the mechanisms of the melt flow instabilities in laser powder bed fusion additive manufacturing process revealed by in-situ high-speed high-resolution synchrotron X-ray imaging. Here we identified powder/droplet impact, significant keyhole oscillation, and melting-mode switching as three major mechanisms for causing melt flow instabilities. We demonstrated the detrimental consequences of these instabilities brought to the process, and presented new understanding on the melt flow evolution and keyhole oscillation. This work provides critical insights into process instabilities during laser metal additive manufacturing, which may guide the development of instability mitigation approaches. The results reported here are also important for the development and validation of high-fidelity computational models.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Sinter formation during directed energy deposition of titanium alloy powders

During directed energy deposition (DED) additive manufacturing, powder agglomeration and sintering can occur outside of the melt pool when using titanium alloy powders. Using in situ synchrotron radiography we investigate the mechanisms by which sintering of Ti6242 powder occurs around the pool, performing a parametric study to determine the influence of laser power and stage traverse speed on sinter build-up. The results reveal that detrimental sinter can be reduced using a high laser power or increased stage traverse speed, although the latter also reduces deposition layer thickness. The mechanism of sinter formation during DED was determined to be in-flight heating of the powder particles in the laser beam. Calculations of particle heating under the processing conditions explored in this study confirm that powder particles can reasonably exceed 700 °C, the threshold for Ti surface oxide dissolution, and thus the powder is prone to sintering if not incorporated into the melt pool. The build-up of sinter powder layer on deposit surfaces led to lack of fusion pores. To mitigate sinter formation and its detrimental effects on DED component quality, it is essential that the powder delivery spot area is smaller than the melt pool, ensuring most powder lands in the melt pool.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Establishment of Microbeam Radiation Therapy at a Small-Animal Irradiator

Microbeam radiation therapy is a preclinical concept in radiation oncology. It spares normal tissue more effectively than conventional radiation therapy at equal tumor control. The radiation field consists of peak regions with doses of several hundred gray, whereas doses between the peaks (valleys) are below the tissue tolerance level. Widths and distances of the beams are in the submillimeter range for microbeam radiation therapy. A similar alternative concept with beam widths and distances in the millimeter range is presented by minibeam radiation therapy. Although both methods were developed at large synchrotron facilities, compact alternative sources have been proposed recently.

62 RADIOLOGY AND NUCLEAR MEDICINE↗
DOE OSTI2021

A Mouse Model for Microbeam Radiation Therapy of the Lung

Radiation therapy is an important treatment component for patients with lung cancer. However, the survival time gained with clinical radiation therapy techniques is relatively short. Data from preclinical experiments suggest that synchrotron microbeam radiation therapy could be much better suited to control malignant brain tumors than current clinical concepts of radiation therapy. Even at peak doses of several hundred gray, the extent of functional deficits is low.

62 RADIOLOGY AND NUCLEAR MEDICINE↗
DOE OSTI2021

In situ study on the compression deformation of MoNbTaVW high-entropy alloy

The excellent mechanical properties of high-entropy alloys (HEAs) make them promising materials for advances in science and technology. However, the underlying mechanism of plastic deformation is not well understood. In situ experiments are urgently required to provide a fundamental understanding of the plastic deformation under high pressure. We performed in situ synchrotron X-ray diffraction (XRD) experiments to study compression deformation behavior of the HEA MoNbTaVW in a radial diamond anvil cell (rDAC). Our results show that the strength and ratio of the stress-to-shear modulus values are ~1.5 and 3 times that of pure tungsten (W), respectively. MoNbTaVW showed plastic deformation above 5 GPa and displayed a much stronger texture. In this work, we found that the active dislocation behavior is mainly responsible for the high strength in MoNbTaVW under compression. This unique technique opens a new avenue to investigate the in situ mechanical properties and their mechanism in other types of HEAs.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Multimodal Analysis of Spatially Heterogeneous Microstructural Refinement and Softening Mechanisms in Three-Pass Friction Stir Processed Al4Si Alloy

Multiple thermally and thermomechanically induced microstructural refinement mechanisms can be activated in metallic alloys when subjected to solid phase processing methods such as friction stir processing (FSP). In this work, we provide detailed descriptions of the relationship between region-specific microstructural refinement mechanisms and the variation in microhardness, through a systematic and multimodal microstructural characterization of an FSP-processed 75% cold-rolled Al-4 at.% Si model binary alloy. Spatially resolved high-energy synchrotron X-ray diffraction, electron backscattered diffraction, and scanning transmission electron microscopy were used to understand the spatially heterogeneous microstructural evolution due to FSP. Results provide insights into how mechanisms such as static recovery, static recrystallization, dynamic recovery and recrystallization, geometric and continuous dynamic recrystallization, and particle-stimulated static or dynamic grain nucleation may occur heterogeneously in the microstructure as a function of the distance from the stir zone in processed alloys, directly influencing the degree of softening. The systematic analysis of microstructures and hardness in the FSP-processed model binary alloy given in this work highlights the rich microstructural domains that can be uniquely harnessed through solid phase processing of metallic alloys.

Al4Si, Friction Stir Processing, Geometric Dynamic↗
DOE OSTI2022

Insights into Ti doping for stabilizing the Na 2/3 Fe 1/3 Mn 2/3 O 2 cathode in sodium ion battery

Iron- and manganese-based layered metal oxides, as cathodes for sodium ion batteries, have received widespread attention because of the low cost and high specific capacity. However, the Jahn-teller effect of Mn 3+ ions and the resulted unstable structure usually lead to continuously capacity decay. Herein, Titanium (Ti) has been successfully doped into Na 2/3 Fe 1/3 Mn 2/3 O 2 to suppress the Jahn-Teller distortion and improve both cycling and rate performance of sodium ion batteries. In situ high-energy synchrotron X-ray diffraction study shows that Ti-doped compound (Na 2/3 Fe 1/3 Mn 0.57 Ti 0.1 O 2 ) can maintain the single P2 phase without any phase transition during the whole charging/discharging process. Further, various electrochemical characterizations are also applied to explore the better kinetics of sodium ions transfer in the Na 2/3 Fe 1/3 Mn 0.57 Ti 0.1 O 2 . This work provides a comprehensive insight into the Ti-doping effects on the performance from both structural and electrokinetic perspectives.

25 ENERGY STORAGE↗
DOE OSTI2026

Coupling geophysical, geological, geochemical and mineralogical assessments to examine preferential contaminant transport pathways in interbedded fractured bedrock

This study shows that a multi-faceted approach, combining borehole geophysical logging and surface seismic P-wave first-arrival tomography with confirmatory coring, well installation, and chemical and mineralogical analysis, is effective for identifying difficult-to-locate preferential contaminant transport pathways in deeper fractured bedrock. Seismic tomography detected porous 10–20 m wide elongated fractured conduits that allow acidic groundwater contaminated with uranium (U) and nitrate (NO 3 - ) to migrate within interbedded shale-limestone bedrock over 1000 m from a former disposal facility (S-3 Ponds site) located at the DOE Y-12 National Security Complex in Tennessee (USA). Conventional drilling techniques would easily miss these conduits because they are oriented parallel with fractured bedding planes. Synchrotron analysis of aquifer solids revealed that > 95 % of the U is hexavalent (U VI ). This uranyl (UO 2 2+ ) species is coordinated with carbonate, iron oxide, silicate and phosphate minerals within cemented white to yellow precipitates, which contain U concentrations as high as ∼21.6 % by weight fraction. Identifying the presence of these mineral phases, enables a further understanding of the potential effectiveness of remediation actions. The combination of methodologies presented here can also be applied to other explorations, such as the detection of water supply.

Fate and transport↗
DOE OSTI2023

Additive manufacturing process parameter determination for a new Fe-C-Cu alloy

As a potential replacement for stainless steel alloys commonly used to print parts with laser powder bed fusion, a new Cu precipitation strengthened ferrous alloy, with composition Fe-0.2C-6Cu (wt%), was recently developed. This material is Co- and Ni-free, printable, has mechanical properties comparable to that of high strength stainless steels (approximately 1300 MPa UTS), and is cost-advantaged relative to existing low-alloy steels for additive manufacturing of parts with complex shapes. To gain traction for broader application, optimal laser powder bed fusion (LPBF) processing conditions to produce nearly defect-free parts without compromising mechanical strength are needed. Here, an optimal processing window based upon laser speeds that achieve minimal porosity was quantified via comparisons of measured melt pool penetration, scan speeds, printed material density and laser beam energy density on a commercial LPBF unit operating at 350 W, 80 μm hatch spacing, and 50 μm layer thickness based upon optimal parameters for 17-4PH. Furthermore, the window is 300 to 500 mm/s to achieve >99.8 % dense Fe-0.2C-6Cu (wt%) specimens. Other defects such as burning, spatter, and lack of fusion were also avoided in this window. The window was validated with in-situ synchrotron X-ray imaging that enabled visualization of the vapor cavity, melting, and solidification during a single laser track scan on a miniature powder bed sample. In addition, in-situ infrared imaging provided temperature fields, cooling rate and solidification range, and confirmed minimal printing defects and spatter within the processing window.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Effects of shielding gas and spot reduction on humping suppression in high-speed laser welding

High-speed laser welding is a crucial process to enhance the production rate of fuel cell fabrication. However, exceeding a critical welding speed leads to defect formation such as humps and root concavities, which degrade weld quality and mechanical performance. This study employed shielding gas and spot reduction approaches to suppress these defects. The relationships between individual defect types and their influence on weld strength were systematically examined. Moreover, in situ high-speed synchrotron X-ray imaging was employed to comprehend the mechanisms of humping mitigation by shielding gas through analysis of instantaneous keyhole and melt pool dynamics. The observations reveal that shielding gas mitigates humping by shortening the molten pool through enhanced surface heat convection and by altering surface tension to prevent melt flow collisions. The effects of shielding gas and spot reduction were further incorporated into the dimensionless humping index (π h ) that describes the humping formation tendency. These findings provide mechanistic insights and quantitative guidance for defect control strategies in high-speed laser welding.

08 HYDROGEN↗
DOE OSTI2023

Structure and magnetism of AlCoCrCuFeNi high-entropy alloy

We report on the investigation of magnetic and structural properties of AlCoCrCuFeNi, which is known to crystallize in a dual phase solid solution: the face-centred cubic (FCC) or the body-centred cubic (BCC). The results of neutron (NPD) and synchrotron powder diffraction (SXRD) allow to partially resolve magnetic information coming from BCC and FCC phases, which is impossible in the bulk magnetic measurements. Electron diffraction (PED) revealed that AlCoCrCuFeNi forms dendritic microstructure with the Cu-rich FCC phase and the Ni-rich BCC phase. Lattice parameters obtained from PED method are in good agreement with parameters obtained after refinement on the basis of powder X-ray diffraction measurements. The local crystal and electronic structure around Co was studied using Co K X-ray Absorption Spectroscopy (XAS). The magnetic measurements show that AlCoCrCuFeNi reveal a ferromagnetic transition at about 330K and displays magnetic hysteresis loop at the room temperature. Results from NPD suggest that the magnetic moment is mostly located in the BCC subsystem. The alloy shows soft magnetic properties. Saturated magnetizations (M s ), remanence ratio (M r /M s ) and coercivity (H c ) of the cast are estimated to be 45.10emu/g, 5.1% and 56 Oe at 300K, respectively. Finally, the BCC-FCC phase transformation up to 673K (400°C) was investigated using temperature dependent NPD, where a possible second BCC phase was identified.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Investigation of breakaway corrosion observed during oxide growth in pure and low alloying element content Zr exposed in water at 360°C

The addition of small concentrations of alloying elements to pure zirconium can prevent nuclear fuel cladding material from undergoing unstable oxide growth in aqueous environments at light water reactor operating temperatures. The role of alloying elements in stabilizing the oxide growth is examined in this paper, to better understand the oxide growth stabilization mechanism. To this end, a set of initial, short-duration corrosion experiments were performed, followed by oxide layer characterization. Specifically, ten model Zr alloys were selected to test the effect of small alloying additions on the alloy corrosion rate and corrosion breakaway. Additionally, these alloys were corrosion tested in pure water in an autoclave at 360°C for up to 70 days. The alloys included crystal bar Zr, sponge Zr, and model alloys with small concentrations of Sn, Fe, and Cr. After testing, the alloys were characterized using scanning electron microscopy (SEM) and synchrotron µ-X-ray fluorescence (µXRF) to study how the structure of the oxide and alloying element distribution related to unstable oxide growth. Initial results in the 360°C water environment showed breakaway oxidation may be caused by unstable oxide growth due to heterogeneous distribution of the alloying elements. Heterogeneous distribution of alloying elements was correlated to the occurrence of unstable oxide growth (either nodule-like, grain boundary penetration, or differential grain-to-grain growth). It is possible that this heterogeneity, made possible by low alloying element content, can cause breakaway corrosion, but further study is warranted.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Global and local texture development during initial plastic deformation of cold-pilgered Zircaloy-4 tubing

In this work we present a thorough characterization of the texture development during the initial step of a cold pilgering process of a Zircaloy-4 TREX tube, on which the axial cross section is reduced by 80% over a 40cm length with an overall Q-ratio of 2.34, followed by a recrystallization thermal treatment. Texture across a tapered specimen representing this working zone was characterized by neutron diffraction and high energy synchrotron x-ray diffraction at 28 positions (4 locations along its length and 7 locations across its thickness with 0.3 mm spatial resolution), and on the deformed end after the thermal treatment. Results show that the starting material (TREX tube) presents a texture gradient through its wall thickness, with the c poles aligned to the hoop direction at the outer surface (with radial and hoop Kearns factors: f R =0.36, f H = 0.50), and gradually rotating around the axial direction to become a quasi-radial orientation (~35 o out of the radial direction) at the inner surface ( f R =0.43, f H =0.35). The overall texture becomes more radial due to the cold pilgering, but the texture gradient remains during the whole deformation process, being always more radial at the inner surface, ( f R =0.53, f H =0.37 at 80%) than at the outer surface ( f R =0.41, f H =0.50at 80%). The most remarkable changes in texture produced by the rolling process is a 30 o rotation of the grains around their c-axis, producing a marked increase of the <11 2 ¯ 0> // axial fiber texture at expenses of the original <10 1 ¯ 0> // axial fiber texture observed in the TREX tube. The observed changes in texture during deformation were correctly explained by visco-plastic self-consistent (VPSC) modelling. This was achieved after the inclusion of the basal <a> slip system, which plays a central role to explain the 30 o rotation around the c-axis during deformation. The texture evolution was correctly described after the inclusion of a drag effect to grain rotation due to the interaction with neighbouring grains. The through thickness texture differences are greatly reduced by the recrystallization thermal treatment, with similar Kearns factors at the inner surface ( f R =0.50, f H =0.28) and the outer surface ( f R =0.48, f H =0.39). The predominance of the <10 1 ¯ 0> // axial fiber texture is recovered after recrystallization.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Polysulfide-incompatible additive suppresses spatial reaction heterogeneity of Li-S batteries

Rational electrolyte engineering for practical pouch cells remains elusive because the correlation between the cathode/solid-electrolyte interphase layer and cell-level reaction behavior is poorly understood. Here, by combining multiscale characterization and computational modeling, we show that—counter to the conventional perception of polysulfide-incompatible additives—the spontaneous reaction of sparingly solvated polysulfides with Lewis acid additives (LAAs) can induce in situ formation of a homogeneous interphase on thick and tortuous S cathode. Multiscale synchrotron X-ray characterization consistently affirms that such interface design could effectively eliminate the notorious problems of polysulfide shuttle and lithium corrosion and, more importantly, provide an interconnected “ion transport highway” to alleviate the uneven ion transport within the tortuous S cathode. Hence, this design dramatically reduces the reaction heterogeneity of lithium-sulfur (Li-S) pouch cells under lean electrolyte conditions. Further, this work resolves controversy around the role of polysulfide-incompatible additives in high-energy Li-S pouch cells and highlights the importance of suppressing reaction heterogeneity for practical batteries.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Dynamic in-situ imaging of methane hydrate formation and self-preservation in porous media

Here we present the results of dynamic in-situ 3D X-ray imaging of methane hydrates microstructure during methane hydrate formation and dissociation in sand samples. Short scanning times and high resolution provided by synchrotron X-rays allowed for better understanding of water movement and different types of gas-hydrate formation. Complementing previous observations, we conclude that the process of gas-hydrate formation is accompanied by the water movements caused by cryogenic water suction that happens in sequences of short fast movements with longer equilibrium states in between (when the water is immobile). Based on the 3D microstructure we identified two distinct types of gas-hydrate formation: (i) into the gas pockets and (ii) inside water volumes. For both mechanisms we do not see problems in gas or water supply to support the gas-hydrate formation. The rate of dissociation in the self-preservation mode (pressure drop at negative temperatures) appears to be different for these two types of gas hydrates. This means that the history of the gas-hydrate formation may influence its behaviour at the dissociation stage (e.g. gas-hydrate production).

58 GEOSCIENCES↗