Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “space electronics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57

Bifurcation-like transition of divertor conditions induced by X-point radiation in KSTAR L-mode plasmas *

Abstract Density ramps with ion grad B drift directed into lower single null KSTAR L-mode plasmas are associated with a simultaneous and abrupt reduction of the divertor particle flux on both low- and high-field-side targets when the mid-plane line averaged electron density reaches a given level. Target embedded Langmuir probe signals show a clear ‘cliff edge’ behavior similar to that observed in the divertor target electron temperature in DIII-D H-mode plasmas (Eldon et al 2017 Nucl. Fusion 57 066039; McLean et al 2015 J. Nucl. Mater. 463 533–6). The collapse of the particle flux is observed along the whole divertor target area (from private flux region to the far scrape-off layer (SOL)). The critical upstream density of this target flux cliff is invariant under fuel gas throughput modulation. The transition along the cliff occurs in tens of milliseconds. With the cliff, carbon impurities and deuterium neutrals transported through the X-point to the core produce a strong radiation spot near the X-point, seen on bolometric signals, and increase the upstream density. The experimental observations are consistent with time-dependent SOLPS-ITER simulations, which also demonstrate an abrupt transition of the target flux and upstream density with the increase in X-point radiation. The timescale of the cliff predicted by SOLPS-ITER is consistent with the experiment, although, it is influenced by gas throughput or time-dependent numerical methods. In the L-mode phase space of separatrix electron density and temperature, branches are divided based on target temperature, because the latter is strongly coupled to the radiation front and ionization front due to the monotonic characteristic of the parallel electron temperature distribution. Since the H-mode condition operates at a much higher upstream density and electron temperature in phase space, dissipation from sputtered carbon alone leads to the density limit before reaching the X-point radiation condition. This is therefore consistent with the fact that cliffs have never been observed in H-mode KSTAR experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Experimental Study of Current-Driven Turbulence During Magnetic Reconnection

CMPD Final Report Experimental Study of Current-Driven Turbulence During Magnetic Reconnection Miklos Porkolab, PI, Jan Egedal, co-PI, William Fox, graduate student. This is the final report for Grant DE-FC02-04ER54786, MIT Participation in the Center for Multiscale Plasma Dynamics, which was active from 8/1/2004 to 7/31/2010. This Grant supported the thesis work of one MIT graduate student, William Fox, The thesis research consisted of an experimental study of the fluctuations arising during magnetic reconnection in plasmas on the Versatile Toroidal Facility (VTF) at MIT Plasma Science and Fusion Center (PSFC). The thesis was submitted and accepted by the MIT physics Department,. Fox, Experimental Study of Current-Driven Turbulence During Magnetic Reconnection, Ph.D. Thesis, MIT (2009). In the VTF experiment reconnection and current-sheet formation is driven by quickly changing currents in a specially arranged set of internal conductors. Previous work on this device [Egedal, et al, PRL 98, 015003, (2007)] identified a spontaneous reconnection regime. In this work fluctuations were studied using impedance-matched, high-bandwidth Langmuir probes. Strong, broadband fluctuations, with frequencies extending from near the lower-hybrid frequency [fLH = (fcefci)1/2] to the electron cyclotron frequency fce were found to arise during the reconnection events. Based on frequency and wavelength measurements, lower-hybrid waves and Trivelpiece-Gould waves were identified. The lower-hybrid waves are easiest to drive with strong perpendicular drifts or gradients which arise due to the reconnection events; an appealing possibility is strong temperature gradients. The Trivelpiece-Gould modes can result from kinetic, bump-on-tail instability of a runaway electron population energized by the reconnection events. We also observed that the turbulence is often spiky, consisting of discrete positive-potential spikes, which were identified as electron phase-space holes, a class of nonlinear solitary wave known to evolve from a strong beam-on-tail instability. We established that fast electrons were produced by magnetic reconnection. Overall, these instabilities were found to be a consequence of reconnection, specifically the strong energization of electrons, leading to steep gradients in both coordinate- and velocity-space. Estimates (using quasi-linear theory) of the anomalous resistivity due to these modes did not appear large enough to substantially impact the reconnection process. Relevant publications: W. Fox, M. Porkolab, et al, Phys. Rev. Lett. 101, 255003 (2008). W. Fox, M. Porkolab, et al, Phys. Plasmas 17, 072303, (2010).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Dynamics of Longitudinal Phase-Space Modulations in an rf Compressor for Electron Beams

Free Electron Lasers (FELs) operating in the UV or x-ray radiation spectrum require peak beam currents that are generally higher than those obtainable by present electron sources, thus making bunch compression necessary. Compression, however, may heighten the effects of collective forces and degrade the beam quality. In this paper they provide a framework for investigating some of these effects in rf compressors by focusing on the longitudinal dynamics of small-amplitude density perturbations, which have the potential to cause the disruptive appearance of the so-called microbunching instability. They develop a linear theory valid for low-to-moderate compression factors under the assumption of a 1D impedance model of longitudinal space charge and provide validation against macroparticle simulations.

43 PARTICLE ACCELERATORS↗

A Simple, Low Cost Longitudinal Phase Space Diagnostic

For proper operation of the LCLS [1] x-ray free-electron laser (FEL), and other similar machines, measurement and control of the electron bunch longitudinal phase space is critical. The LCLS accelerator includes two bunch compressor chicanes to magnify the peak current. These magnetic chicanes can generate significant coherent synchrotron radiation (CSR), which can distort the phase space distribution. We propose a diagnostic scheme by exciting a weak skew quadrupole at an energy-chirped, high dispersion point in the first LCLS bunch compressor (BC1) to reconstruct longitudinal phase space on an OTR screen after BC1, allowing a time-resolved characterization of CSR effects.

43 PARTICLE ACCELERATORS↗

The Warm Electron Beam Ion Trap (WEBIT): An instrument for ground calibration of space-borne x-ray spectrometers

The warm electron beam ion trap (WEBIT) at Lawrence Livermore National Laboratory is being developed as a pre-launch, ground calibration source for space-borne, high-throughput, high-resolution x-ray spectrometers, such as the x-ray imaging and spectroscopy mission Resolve quantum calorimeter. Historically, calibration sources for calorimeter spectrometers have relied on characteristic line emission from x-ray tubes, fluorescing metals, and radioactive sources. The WEBIT, by contrast, relies on emission from x-ray transitions in highly charged ions, for example, hydrogen-like and helium-like ions, whose energies are well known and whose line shapes are relatively simple. The WEBIT can create astrophysically relevant ions whose x-ray emission falls in the 0.3-12 keV science bandpass of Resolve and has a portable design advantageous for a calibration source. The WEBIT will be used to help calibrate Resolve’s instrumental line shape and gain scale as a function of various operational parameters during both detector subsystem level testing and instrumental level testing.

47 OTHER INSTRUMENTATION↗

Summary Report on Beam and Radiation Generation, Monitoring and Control

The discussions of the working group on beam and radiation generation, monitoring, and control (working group 6) at the 2008 advanced accelerator concepts workshop are summarized. The discussions concerned electron injectors, phase space manipulation, beam diagnostics, pulse train generation, intense beam physics, and radiation generation.

43 PARTICLE ACCELERATORS↗

Spin-Hall effect of collimated electrons in zinc-blende semiconductors

We describe an intrinsic spin-Hall effect (SHE) in n-type bulk zinc-blende semiconductors with a topological origin. When a collimated flux of electrons is injected into a zinc-blende semiconductor with Dresselhaus spin-orbit interaction, a nontrivial gauge structure appears in the momentum (k{sup {yields}}-) space of the electrons. The Berry curvature of this gauge field and the corresponding Lorentz force in k{sup {yields}}-space results in a finite SHE. The value of the spin-Hall current is found to be highly dependent on the degree of electron collimation, which may be varied by means of gate electrodes. Therefore, the system may potentially be useful as an electronically controllable source of pure spin-current for spintronic applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Complex Role of Secondary Electron Emissions in Dust Grain Charging in Space Environments: Measurements on Apollo 11 and 17 Dust Grains

Dust grains in various astrophysical environments are generally charged electrostatically by photoelectric emissions with radiation from nearby sources, or by electron/ion collisions by sticking or secondary electron emissions. Knowledge of the dust grain charges and equilibrium potentials is important for understanding of a variety of physical and dynamical processes in the interstellar medium (ISM), and heliospheric, interplanetary, planetary, and lunar environments. The high vacuum environment on the lunar surface leads to some unusual physical and dynamical phenomena involving dust grains with high adhesive characteristics, and levitation and transportation over long distances. It has been well recognized that the charging properties of individual micron/submicron size dust grains are expected to be substantially different from the corresponding values for bulk materials and theoretical models. In this paper we present experimental results on charging of individual dust grains selected from Apollo 11 and Apollo 17 dust samples by exposing them to mono-energetic electron beams in the 10- 400 eV energy range. The charging rates of positively and negatively charged particles of approximately 0.2 to 13 microns diameters are discussed in terms of the secondary electron emission (SEE) process, which is found to be a complex charging process at electron energies as low as 10-25 eV, with strong particle size dependence. The measurements indicate substantial differences between dust charging properties of individual small size dust grains and of bulk materials.

Abbas, M. M.↗

Evaluation of Automotive Grade Resistors for Space Flight

Over the past decade, electronic, electrical, and electromechanical (EEE) parts for space applications have undergone significant changes, largely driven by CubeSat and commercial space developers pushing the boundaries on the utilization of commercial parts in space. Global product shortages and shipping delays are still impacting space flight project deadlines. Many projects have turned to automotive grade resistors as an alternate to their MILSPEC counterparts to fulfill requirements. In addition, automotive grade resistors may offer designers a wider range of parts to consider. A recent NASA study recommended the use of high-volume manufactured commercial components for space applications provided these components show evidence of stringent fabrication controls and thorough reliability monitoring practices. Automotive grade components have stringent qualification requirements per the Automotive Electronic Council (AEC). However, the end user usually does not have insight into the practices the manufacturer may use to reduce/eliminate infant mortality nor for compliance to all datasheet specifications. Screening, Life and Accelerated Life testing on a set of standard automotive-grade chip resistors is proposed to evaluate the reliability of these components. Requirements from both the AEC-Q (Automotive Electronic Council Qualification) and EEE-INST-002 (Instructions for EEE Parts Selection, Screening, Qualification, and Derating) for resistors is compared and discussed. The resistors have been tested by using a modified methodology from EEEINST-002 to evaluate their reliability for space flight projects. The findings of this study indicate that the underlying degradation mechanisms at rated temperature and power are best represented by power law models with a fitted exponent between 0 and 1. A linear model is more conservative which compensates for potential model uncertainty given the wide range of design and materials used in automotive resistors, while still providing useful long-term resistance drift estimates. No electrical anomalies or failures were observed throughout the 1000-hour Life Tests other than small in tolerance resistance drift aging. Degradation models were utilized to quantify and extrapolate the long-term resistance drift under operating conditions for the components. The models demonstrated that some automotive-grade resistors are likely to operate 10 years at nominal usage conditions while others might fail earlier.

Zainab Abdullahi↗

Numerical simulations of runaway electron generation in pressurized gases

The results of a numerical simulation of the generation of runaway electrons in pressurized nitrogen and helium gases are presented. It was shown that runaway electrons generation occurs in two stages. In the first stage, runaway electrons are composed of the electrons emitted by the cathode and produced in gas ionization in the vicinity of the cathode. This stage is terminated with the formation of the virtual cathode, which becomes the primary source of runaway electrons in the second stage. Also, it was shown that runaway electrons current is limited by both the shielding of the field emission by the space charge of the emitted electrons and the formation of a virtual cathode. In addition, the influence of the initial conditions, such as voltage rise time and amplitude, gas pressure, and the type of gas, on the processes that accompany runaway electrons generation is presented.

74 ATOMIC AND MOLECULAR PHYSICS↗

Evaluation of Automotive Grade Resistors for Space Flight

Over the past decade, electronic, electrical, and electromechanical (EEE) parts for space applications have undergone significant changes, largely driven by CubeSat and commercial space developers pushing the boundaries on the utilization of commercial parts in space. Global product shortages and shipping delays are still impacting space flight project deadlines. Many projects have turned to automotive grade resistors as an alternate to their MIL-SPEC counterparts to fulfill requirements. In addition, automotive grade resistors may offer designers a wider range of parts to consider. A recent NASA study recommended the use of high-volume manufactured commercial components for space applications provided these components show evidence of stringent fabrication controls and thorough reliability monitoring practices [1]. Automotive grade components have stringent qualification requirements per the Automotive Electronic Council (AEC). However, the end user usually does not have insight into the practices the manufacturer may use to reduce/eliminate infant mortality nor for compliance to all datasheet specifications. Screening, Life and Accelerated Life testing on a set of standard automotive-grade chip resistors is proposed to evaluate the reliability of these components. Requirements from both the AEC-Q (Automotive Electronic Council Qualification) and EEE-INST-002 (Instructions for EEE Parts Selection, Screening, Qualification, and Derating) for resistors is compared and discussed. The resistors have been tested by using a modified methodology from EEE-INST-002 to evaluate their reliability for space flight projects. The findings of this study indicate that the underlying degradation mechanisms at rated temperature and power are best represented by power law models with a fitted exponent between 0 and 1. A linear model is more conservative which compensates for potential model uncertainty given the wide range of design and materials used in automotive resistors, while still providing useful long-term resistance drift estimates. No electrical anomalies or failures were observed throughout the 1,000-hour Life Tests other than small in tolerance resistance drift aging. Degradation models were utilized to quantify and extrapolate the long-term resistance drift under operating conditions for the components. The models demonstrated that some automotive-grade resistors are likely to operate 10 years at nominal usage conditions while others might fail earlier.

Zainab Abdullahi↗

Electron reflection in thermionic energy converters

We investigate the impact of electron reflection on space charge in thermionic energy converters. Using the particle-in-cell code Warp3D, we simulate electron reflection and discover that specular and diffuse reflection produce fundamentally distinct behavior. Our simulations suggest that the effects of reflection may have been misidentified in experiments as anomalously large gap sizes. As a result, electron reflection may significantly alter the analysis and optimization of real-world converters.

Lim, Ian T.↗

Time-resolved view on charge-resonance-enhanced ionization

We theoretically investigate the electronic dynamics in the hydrogen molecular ion at fixed intermediate internuclear distances in two-dimensional space for the electron in a linearly polarized laser field. Our results of numerical simulations confirm the predictions of multiple bursts of ionization within a half cycle of the laser field oscillation as recently reported for one-dimensional models. Based on the analysis of the Floquet states for a two-state model of the molecular ion, we discuss the relation of the multiple ionization bursts to the so-called charge-resonance-enhanced ionization phenomenon and the momentum gates.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

A heavy ion beam probe system for investigation of a modified Penning discharge

An ion beam probe diagnostic system can measure time- and space-resolved profiles of plasma space potential and electron density. In combination with a computer iterative technique, the ion beam probe can determine both the space potential profile in plasmas containing strong electric fields and potentials comparable in magnitude to the energy of the probing ion beam. During ion beam probing of a modified Penning discharge, several groups of secondary ions were observed coming from the plasma with a fixed primary beam energy and momentum. The energies of these ions were within 10 percent of the values predicted by a computer-generated model of the potential profile in the plasma. The mechanical and electronic components of the system are described, with particular emphasis on those features required to probe plasma potentials comparable in magnitude to the ion beam energy.

Kambic, G. X.↗

Direct Measurement of the Spectral Structure of Cosmic-Ray Electrons+Positrons in the Tev Region With Calet on the International Space Station

Detailed measurements of the spectral structure of cosmic-ray electrons and positrons from 10.6 GeV to 7.5 TeV are presented from over 7 years of observations with the CALorimetric Electron Telescope (CALET) on the International Space Station. The instrument, consisting of a charge detector, an imaging calorimeter, and a total absorption calorimeter with a total depth of 30 radiation lengths at normal incidence and a fine shower imaging capability, is optimized to measure the all-electron spectrum well into the TeV region. Because of the excellent energy resolution (a few percent above 10 GeV) and the outstanding e/p separation (10 5 ), CALET provides optimal performance for a detailed search of structures in the energy spectrum. The analysis uses data up to the end of 2022, and the statistics of observed electron candidates has increased more than 3 times since the last publication in 2018. By adopting an updated boosted decision tree analysis, a sufficient proton rejection power up to 7.5 TeV is achieved, with a residual proton contamination less than 10%. The observed energy spectrum becomes gradually harder in the lower energy region from around 30 GeV, consistently with AMS-02, but from 300 to 600 GeV it is considerably softer than the spectra measured by DAMPE and Fermi-LAT. At high energies, the spectrum presents a sharp break around 1 TeV, with a spectral index change from −3.15 to −3.91, and a broken power law fitting the data in the energy range from 30 GeV to 4.8 TeV better than a single power law with 6.9 sigma significance, which is compatible with the DAMPE results. The break is consistent with the expected effects of radiation loss during the propagation from distant sources (except the highest energy bin). We have fitted the spectrum with a model consistent with the positron flux measured by AMS-02 below 1 TeV and interpreted the electron+positron spectrum with possible contributions from pulsars and nearby sources. Above 4.8 TeV, a possible contribution from known nearby supernova remnants, including Vela, is addressed by an event-by-event analysis providing a higher proton-rejection power than a purely statistical analysis.

O. Adriani↗

Structural, magnetic, and transport properties of sputtered hexagonal MnNiGa thin films

We report on a systematical study of the structure, magnetism, and magnetotransport behavior of the hexagonal MnNiGa films deposited on thermally oxidized Si (001) substrates by magnetron sputtering. X-ray diffractions reveal that all the films deposited at different temperatures crystallized in hexagonal Ni{sub 2}In-type structure (space group P6{sub 3}/mmc). Scanning electron microscopy observations show that the surface morphology of the films varies with deposition temperature, and energy dispersive spectroscopy analysis shows compositions of the films remain nearly unchanged, independent of the deposition temperature. Magnetic measurements indicate that all films are ferromagnetic and exhibit a magnetic anisotropy behavior. The magnetoresistance (MR) exhibits a negative temperature- and field-dependent behavior. The possible origin of the negative MR is discussed. Furthermore, we found that the Hall effect is dominated by an anomalous Hall effect (AHE) only due to skew scattering independent of the deposition temperature of films. Moreover, the anomalous Hall resistivity presents a non-monotonously temperature-dependent behavior.

36 MATERIALS SCIENCE↗

Evolution of grain boundary conduction with increasing temperature in pure and Ti doped Co ferrite materials

We report on the structural, temperature, and frequency dependent impedance studies of Ti doped cobalt ferrite material (CoFe{sub 1.95}Ti{sub 0.05}O{sub 4}) in comparison with the pure CoFe{sub 2}O{sub 4}. XRD and Raman spectroscopy studies confirm the inverse spinel crystallization of the materials with space group of Fd-3 m. Scanning electron microscope images shows the microcrystalline nature of the particles. Homogeneity, stoichiometry, and ionic states of the ions in the composition were confirmed by energy dispersive X-ray analysis and X-ray photoelectron spectroscopic studies. Temperature and frequency dependent real (Z′) and imaginary (Z″) part of the impedance shows the existence of relaxation processes and their distribution in CoFe{sub 2}O{sub 4} and CoFe{sub 1.95}Ti{sub 0.05}O{sub 4} materials. Complex impedance spectroscopy studies at low temperatures shows that the conductivity in these materials is predominantly due to the intrinsic bulk grains. With increasing the temperature, evolution of grain boundary conduction is clearly seen through the appearance of a second semi-circle in the complex impedance plots. Room temperature total dc conductivity of both CoFe{sub 2}O{sub 4} and CoFe{sub 1.95}Ti{sub 0.05}O{sub 4} materials is found to be 5.78 × 10{sup −8} and 1.61 × 10{sup −7} S/cm, respectively. Temperature variation of dc electrical conductivity follows the Arrhenius relationship and the activation energies for CoFe{sub 2}O{sub 4} corresponding to grain (0.55 eV for CoFe{sub 2}O{sub 4}), grain boundary (0.52 eV), and total conduction (0.54 eV) are discussed. Observation of well distinguishable grain and grain boundary conductions and the low conductivity values in CoFe{sub 2}O{sub 4} and CoFe{sub 1.95}Ti{sub 0.05}O{sub 4} materials indicates that these materials are promising candidates for the high frequency applications.

36 MATERIALS SCIENCE↗

Space instruments

Pulse height analyzer, imaging astronomical photometer, and secondary electron conduction vidicon for space application

Source record↗