Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “power density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Increasing the Pressure‐Free Stripping Capacity of the Lithium Metal Anode in Solid‐State‐Batteries by Carbon Nanotubes

Abstract Lithium metal is the key anode material for solid‐state‐batteries as its successful implementation will drastically increase their energy and power densities. However, anode contact loss during stripping leads to dendrites upon plating and subsequent cell failure. Design strategies to mitigate these issues are crucial to enable the use of lithium metal anodes. This paper reports the dissolution kinetics of composite anodes made of lithium metal and carbon nanotubes (CNTs) with a garnet‐type solid electrolyte (SE). In addition to an enhancement of the effective diffusion within the anode, its dissolution is fundamentally changed from being 2D to 3D. By maintaining contact with the SE, the CNTs facilitate lithium transport to the interface, which yields more than 20 mAh cm −2 discharge capacity at 100 µ A cm −2 without the application of external stack pressure ( > 1 MPa). Conclusions drawn from electrochemical data on the anode microstructure are validated using cryo‐focused‐ion‐beam scanning electron microscopy and correlated with the mechanical properties. Micro‐indentation, acoustic analysis, and stress–strain testing show that mechanical properties of the anode, like yield strength and hardness, are adjustable. Overall, it is shown that the mechanical and electrochemical properties of Li–CNT composite electrodes can be tailored to suit the requirements of a practical cell.

Fuchs, Till↗
DOE OSTI2022

Carbon-Nanotube-Bridging Strategy for Integrating Single Fe Atoms and NiCo Nanoparticles in a Bifunctional Oxygen Electrocatalyst toward High-Efficiency and Long-Life Rechargeable Zinc–Air Batteries

The development of highly efficient and robust bifunctional electrocatalysts for oxygen reduction (ORR) and evolution reactions (OER) is the key issue for realizing high-performance and long-life rechargeable zinc–air batteries (ZABs). However, it is still a great challenge to integrate independent ORR and OER sites in a catalyst with high activity. Here, a carbon nanotube-bridging strategy is proposed to synthesize such a bifunctional oxygen electrocatalyst enriched with highly active single-atom Fe sites for the ORR and high-performance nanosized NiCo hydroxides for the OER. Consequently, the developed catalyst shows a small overpotential difference of 0.686 V. When used as an oxygen electrode catalyst, the corresponding ZAB exhibits a large power density of 219.5 mW cm ₋2 , a small charge–discharge voltage gap of 0.72 V at 10 mA cm ₋2 , and outstanding discharge–charge durability without attenuation after more than 700 cycles. This work proposes a new idea to realize multifunctional catalysts and drives the practical application of ZABs.

25 ENERGY STORAGE↗
DOE OSTI2023

Advanced Materials and Additive Manufacturing for Phase Change Thermal Energy Storage and Management: A Review

Abstract Phase change materials (PCMs) can enhance the performance of energy systems by time shifting or reducing peak thermal loads. The effectiveness of a PCM is defined by its energy and power density—the total available storage capacity (kWh m −3 ) and how fast it can be accessed (kW m −3 ). These are influenced by both material properties as well as geometry of the energy systems; however, prior efforts have primarily focused on improving material properties, namely, maximizing latent heat of fusion and increasing thermal conductivity. The latter is often at the expense of the former. Advanced manufacturing techniques hold tremendous potential to enable co‐optimization of material properties and device geometry, while potentially reducing material waste and manufacturing time. There is an emerging body of research focused on additive manufacturing of PCM composites and devices for thermal energy storage (TES) and thermal management. In this article, the fundamentals and applications of PCMs are reviewed and recent additive manufacturing advances in latent heat TES for both the PCM composite and associated heat exchanger are discussed. A forward‐looking perspective on the future and potential of PCM additive manufacturing for TES and thermal management is provided.

25 ENERGY STORAGE↗
DOE OSTI2022

Cylindrical C 96 Fullertubes: A Highly Active Metal‐Free O 2 ‐Reduction Electrocatalyst

Abstract A new isolation protocol was recently reported for highly purified metallic Fullertubes D 5h ‐C 90 , D 3d ‐C 96 , and D 5d ‐C 100, which exhibit unique electronic features. Here, we report the oxygen reduction electrocatalytic behavior of C 60 , C 70 (spheroidal fullerenes), and C 90 , C 96 , and C 100 (tubular fullerenes) using a combination of experimental and theoretical approaches. C 96 (a metal‐free catalyst) displayed remarkable oxygen reduction reaction (ORR) activity, with an onset potential of 0.85 V and a halfway potential of 0.75 V, which are close to the state‐of‐the‐art Pt/C benchmark catalyst values. We achieved an excellent power density of 0.75 W cm −2 using C 96 as a modified cathode in a proton‐exchange membrane fuel cell, comparable to other recently reported efficient metal‐free catalysts. Combined band structure (experimentally calculated) and free‐energy (DFT) investigations show that both favorable energy‐level alignment active catalytic sites on the carbon cage are responsible for the superior activity of C 96 .

Sanad, Mohamed Fathi↗
DOE OSTI2023

Direct Insertion Polymerization of Ionic Monomers: Rapid Production of Anion Exchange Membranes

Abstract The limited number of methods to directly polymerize ionic monomers currently hinders rapid diversification and production of ionic polymeric materials, namely anion exchange membranes (AEMs) which are essential components in emerging alkaline fuel cell and electrolyzer technologies. Herein, we report a direct coordination‐insertion polymerization of cationic monomers, providing the first direct synthesis of aliphatic polymers with high ion incorporations and allowing facile access to a broad range of materials. We demonstrate the utility of this method by rapidly generating a library of solution processable ionic polymers for use as AEMs. We investigate these materials to study the influence of cation identity on hydroxide conductivity and stability. We found that AEMs with piperidinium cations exhibited the highest performance, with high alkaline stability, hydroxide conductivity of 87 mS cm −1 at 80 °C, and a peak power density of 730 mW cm −2 when integrated into a fuel cell device.

Hsu, Jesse H.↗
DOE OSTI2022

Cylindrical C 96 Fullertubes: A Highly Active Metal-Free O 2 -Reduction Electrocatalyst

A new isolation protocol was recently reported for highly purified metallic Fullertubes D 5h -C 90 , D 3d -C 96 , and D 5d -C 100 , which exhibit unique electronic features. Here, we report the oxygen reduction electrocatalytic behavior of C 60 , C 70 (spheroidal fullerenes), and C 90 , C 96 , and C 100 (tubular fullerenes) using a combination of experimental and theoretical approaches. C 96 (a metal-free catalyst) displayed remarkable oxygen reduction reaction (ORR) activity, with an onset potential of 0.85 V and a halfway potential of 0.75 V, which are close to the state-of-the-art Pt/C benchmark catalyst values. Here we achieved an excellent power density of 0.75 W cm −2 using C 96 as a modified cathode in a proton-exchange membrane fuel cell, comparable to other recently reported efficient metal-free catalysts. Combined band structure (experimentally calculated) and free-energy (DFT) investigations show that both favorable energy-level alignment active catalytic sites on the carbon cage are responsible for the superior activity of C 96 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Atomically Dispersed Pentacoordinated‐Zirconium Catalyst with Axial Oxygen Ligand for Oxygen Reduction Reaction

Single-atom catalysts (SACs), as promising alternatives to Pt-based catalysts, suffer from the limited choice of center metals and low single-atom loading. Here, we report a pentacoordinated Zr-based SAC with nontrivial axial O ligands (denoted O-Zr-N-C) for oxygen reduction reaction (ORR). The O ligand downshifts the d-band center of Zr and confers Zr sites with stable local structure and proper adsorption capability for intermediates. Consequently, the ORR performance of O-Zr-N-C prominently surpasses that of commercial Pt/C, achieving a half-wave potential of 0.91 V vs. reversible hydrogen electrode and outstanding durability (92% current retention after 130-hour operation). Moreover, the Zr site shows good resistance towards aggregation, enabling the synthesis of Zr-based SAC with high loading (9.1 wt%). With the high-loading catalyst, the zinc-air battery (ZAB) delivers a record-high power density of 324 mW cm -2 among those of SAC-based ZABs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Direct Insertion Polymerization of Ionic Monomers: Rapid Production of Anion Exchange Membranes

The limited number of methods to directly polymerize ionic monomers currently hinders rapid diversification and production of ionic polymeric materials, namely anion exchange membranes (AEMs) which are essential components in emerging alkaline fuel cell and electrolyzer technologies. Herein, we report a direct coordination-insertion polymerization of cationic monomers, providing the first direct synthesis of aliphatic polymers with high ion incorporations and allowing facile access to a broad range of materials. We demonstrate the utility of this method by rapidly generating a library of solution processable ionic polymers for use as AEMs. We investigate these materials to study the influence of cation identity on hydroxide conductivity and stability. Furthermore, we found that AEMs with piperidinium cations exhibited the highest performance, with high alkaline stability, hydroxide conductivity of 87 mS cm –1 at 80 °C, and a peak power density of 730 mW cm –2 when integrated into a fuel cell device.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Working Principle of an Ionic Liquid Interlayer During Pressureless Lithium Stripping on Li 6.25 Al 0.25 La 3 Zr 2 O 12 (LLZO) Garnet‐Type Solid Electrolyte

Abstract Solid‐state‐batteries employing lithium metal anodes promise high theoretical energy and power densities. However, morphological instability occurring at the lithium/solid–electrolyte interface when stripping and plating lithium during cell cycling needs to be mitigated. Vacancy diffusion in lithium metal is not sufficiently fast to prevent pore formation at the interface above a certain current density during stripping. Applied pressure of several MPa can prevent pore formation, but this is not conducive to practical application. This work investigates the concept of ionic liquids as “self‐adjusting” interlayers to compensate morphological changes of the lithium anode while avoiding the use of external pressure. A clear improvement of the lithium dissolution process is observed as it is possible to continuously strip more than 70 μm lithium (i. e., 15 mAh cm −2 charge) without the need for external pressure during assembly and electrochemical testing of the system. The impedance of the investigated electrodes is analyzed in detail, and contributions of the different interfaces are evaluated. The conclusions are corroborated with morphology studies using cryo‐FIB‐SEM and chemical analysis using XPS. This improves the understanding of the impedance response and lithium stripping in electrodes employing liquid interlayers, acting as a stepping‐stone for future optimization.

Fuchs, Till↗
DOE OSTI2022

Amorphization of Pseudocapacitive T−Nb 2 O 5 Accelerates Lithium Diffusivity as Revealed Using Tunable Isomorphic Architectures

Abstract Intercalation pseudocapacitance can combine capacitor‐like power densities with battery‐like energy densities. Such surface‐limited behavior requires rapid diffusion where amorphization can increase solid‐state diffusivity. Here intercalation pseudocapacitive materials with tailored extents of amorphization in T‐Nb 2 O 5 are first reported. Amorphization was characterized with WAXS, XPS, XAFS, and EPR which suggested a peroxide‐rich (O 2 2− ) surface that was consistent with DFT predictions. A series of tunable isomorphic architectures enabled comparisons while independently varying transport parameters. Through process of elimination, solid‐state lithium diffusion was identified as the dominant diffusive‐constraint dictating the maximum voltage sweep rate for surface‐limited kinetics ( v SLT ), termed the Surface‐Limited Threshold (SLT). The v SLT increased with amorphization however stable cycling required crystalline T‐Nb 2 O 5 . A current‐response model using series‐impedances well‐matched these observations. This perspective revealed that amorphization of T‐Nb 2 O 5 enhanced solid‐state diffusion by 12.2 % and increased surface‐limitations by 17.0 % (stable samples). This approach enabled retaining 95 % lithiation capacity at ∼800 mV s −1 (1,600 C‐rate equivalent).

25 ENERGY STORAGE↗
DOE OSTI2023

Optimizing the Composite Cathode Microstructure in All‐Solid‐State Batteries by Structure‐Resolved Simulations

Abstract All‐solid‐state batteries are considered as an enabler for applications requiring high energy and power density. However, they still fall short of their theoretical potential due to various limitations. One issue is poor charge transport kinetics resulting from both material inherit limitations and non‐optimized design. Therefore, a better understanding of the relevant properties of the cathode microstructure is necessary to improve cell performance. In this article, we identify optimization potentials of the composite cathode by structure‐resolved electrochemical 3D‐simulations. In our simulation study, we investigate the influence of cathode active material fraction, density, particle size, and active material properties on cell performance. Special focus is set on the impact of grain boundaries on the cathode design. Based on our simulation results, we can predict target values for cell manufacturing and reveal promising optimization strategies for an improved cathode design.

25 ENERGY STORAGE↗
DOE OSTI2024

Converting Second‐Order Saddle Points to Transition States: New Principles for the Design of 4π Photoswitches

Abstract Molecular photoswitches have demonstrated potential for storing solar energy at the molecular level, with power densities comparable to commercial batteries and hydroelectric energy storage. However, development of efficient photoswitches is hindered by limitations in cyclability and optical properties of existing materials. We here demonstrate that certain limitations in photoswitches based on electrocyclizations stem from the issue of controlling competition between Woodward‐Hoffmann allowed and forbidden pathways. Our approach moves beyond the traditional view of activation barriers and reveals that second‐order saddle points are crucial in dictating the competition between disrotatory and conrotatory pathways. These insights suggest new opportunities to manipulate the competition between these pathways through geometric constraints, fundamentally altering the connectivity of the potential energy surface. Our study also emphasizes the necessity of multi‐reference methods and the need to conduct higher‐dimensional explorations for competing pathways beyond photoswitch design.

Chemistry↗
DOE OSTI2024

Ionic Thermoelectric Generators in Vertical and Planar Topologies Based on Fluorinated Polymer Hybrid Materials with Ionic Liquids

Abstract Ionic thermoelectrics (TEs), in which voltage generation is based on ion migration, are suitable for applications based on their low cost, high flexibility, high ionic conductivity, and wide range of Seebeck coefficients. This work reports on the development of ionic TE materials based on the poly(vinylidene fluoride‐trifluoroethylene), Poly(VDF‐co‐TrFE), as host polymer blended with different contents of the ionic liquid, IL, 1‐ethyl‐3‐methylimidazolium bis(trifluoromethylsulfonyl)imide, [EMIM][TFSI]. The morphology, physico‐chemical, thermal, mechanical, and electrical properties of the samples are evaluated together with the TE response. It is demonstrated that the IL acts as a nucleating agent for polymer crystallization. The mechanical properties and ionic conductivity values are dependent on the IL content. A high room temperature ionic conductivity of 0.008 S cm −1 is obtained for the sample with 60 wt% of [EMIM][TFSI] IL. The TE properties depend on both IL content and device topology‐vertical or planar‐the largest generated voltage range being obtained for the planar topology and the sample with 10 wt% of IL content, characterized by a Seebeck coefficient of 1.2 mV K −1 . Based on the obtained maximum power density of 4.9 µW m −2 , these materials are suitable for a new generation of TE devices.

Pereira, Nelson↗
DOE OSTI2020

Simultaneously Integrating Single Atomic Cobalt Sites and Co 9 S 8 Nanoparticles into Hollow Carbon Nanotubes as Trifunctional Electrocatalysts for Zn–Air Batteries to Drive Water Splitting

The development of rechargeable metal–air batteries and water electrolyzers are highly constrained by electrocatalysts for the oxygen reduction reaction (ORR), oxygen evolution reaction (OER), and hydrogen evolution reaction (HER). However, the construction of efficient trifunctional electrocatalysts for ORR/OER/HER are highly desirable yet challenging. Herein, hollow carbon nanotubes integrated single cobalt atoms with Co9S8 nanoparticles (CoSA + Co 9 S 8 /HCNT) are fabricated by a straightforward in situ self-sacrificing strategy. The structure of the CoSA + Co 9 S 8 /HCNT are verified by X-ray absorption spectroscopy and aberration-corrected scanning transmission electron microscopy. Theoretical calculations and experimental results embrace the synergistic effects between Co 9 S 8 nanoparticles and single cobalt atoms through optimizing the electronic configuration of the CoN4 active sites to lower the reaction barrier and facilitating the ORR, OER, and HER simultaneously. Consequently, rechargeable liquid and all-solid-state flexible Zn–air batteries based on CoSA + Co 9 S 8 /HCNT exhibit remarkable stability and excellent power density of 177.33 and 51.85 mW cm -2 , respectively, better than Pt/C + RuO 2 counterparts. Moreover, the as-fabricated Zn–air batteries can drive an overall water splitting device assembled with CoSA + Co 9 S 8 /HCNT and achieve a current density of 10 mA cm -2 at a low voltage of 1.59 V, also superior to Pt/C + RuO 2 . Therefore, we conclude, this work presents a promising approach to an efficient trifunctional electrocatalyst toward practical applications.

25 ENERGY STORAGE↗
DOE OSTI2026

Enhanced Electrocatalytic and Cathode‐Electrolyte Interfacial Properties With a Pr‐Based Simple Perovskite/Ruddlesden‐Popper Nanocomposite Cathode in Protonic Ceramic Fuel Cells

The sluggish kinetics and poor stability of the oxygen reduction reaction (ORR) remain the primary bottleneck for achieving high performance in protonic ceramic fuel cells (PCFCs) at intermediate temperatures (400–650°C). In this work, a Pr-based nanocomposite cathode comprised of simple perovskite phase (PrNi 0.7 Co 0.3 O 3-δ ) and Ruddlesden-Popper phase (Co-doped Pr 4 Ni 3 O 10+δ ) is developed. Although PrNi 0.7 Co 0.3 O 3-δ solely stands as a good cathode with facile proton transfer, combining the superior catalytic activity against oxygen on the Ruddlesden-Popper phase boosts the ORR performance further. The designed nanocomposite cathode outperforms the simple perovskite cathode, attributed to enhanced oxygen absorption and surface diffusion with the Ruddlesden-Popper phase. A precursor-based cathode deposition technique is also developed to achieve cathode grain sizes of ∼100 nm. A single cell with the nanocomposite cathode delivers a peak power density of 1.38 W cm −2 at 650°C, among the highest in reported PCFCs with Pr-based cathodes, with a small degradation rate of 0.145 mV h −1 during 250 h stability test. Further investigation of cathode-electrolyte interface revealed interfacial PrO 2 phase formation, promoted by abundant Pr 6 O 11 in the nanocomposite precursor powder, thereby improving both ohmic resistance and stability. These findings highlight the effectiveness of the nanocomposite cathode and underscore its advantages on interfacial properties.

08 - HYDROGEN↗
DOE OSTI2023

The Linkage Between Electro-Chemical Mechanical Instabilities in Battery Materials

Battery chemistry must be diversified to achieve a sustainable energy landscape by effectively utilizing renewable energy sources. Alkali metal-ion, all-solid-state, metal–air batteries, and multivalent batteries offer unique cost, safety, raw material abundance, energy, and power density solutions. However, realizing these “beyond Li-ion batteries” must uncover their working principles and performance & property relationships. In this aspect, mitigating chemo-mechanical instabilities in the structure and surface of the electrodes plays a crucial role in their performance. Unfortunately, the coupling between electrochemical and mechanical interactions is often poorly understood due to a lack of operando characterization. Here, this review article explains the working principles of curvature measurement and digital image correlation for measuring stress and strain generations in battery materials. We provided specific examples of how these operando mechanical measurements shed light on instabilities in alkali metal ion electrodes, solid electrolytes, Li-O 2 batteries, and aqueous Zn-ion batteries. Operando mechanical measurements offer an effective way to map changes in the physical fingerprint of the battery materials, therefore providing crucial information to elucidate instabilities in battery materials.

25 ENERGY STORAGE↗
DOE OSTI2021

Time-Resolved Geometric Feature Tracking Elucidates Laser-Induced Keyhole Dynamics

In this report, during laser melting of metals, localized metal evaporation resulting in the formation of a keyhole shaped cavity can occur if processing conditions are chosen with high power density. An unstable keyhole can have deleterious effects in certain applications (e.g., laser powder bed fusion) as it increases the likelihood of producing defects such as porosity. In this work, we propose a pipeline that enables complete segmentation and extraction of various geometric features in keyholing conditions. In situ synchrotron high-speed X-ray visualization at the Advanced Photon Source provides large datasets of experimental images with a high spatio-temporal resolution across a range of laser parameters for Ti-6Al- 4 V. Computer vision image processing techniques were used to extract time-resolved quantitative geometric features (e.g., depth, width, front wall angle) throughout keyhole evolution which were subsequently analyzed to understand the relationship between the variation of local keyhole geometry and processing conditions. This analysis is the first to employ a data-driven approach to further our understanding of the keyholing process regime.

36 MATERIALS SCIENCE↗