Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “optimization for fusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57

Powder Bed Fusion Additive Manufacturing of JBK-75

JBK-75 is an iron-nickel derivative alloy of A-286 that has been of interest to NASA’s propulsion community for use in fuel injectors and other components that are used in hot, corrosive environments. To enable the rapid production of these components in JBK-75, Marshall Space Flight Center has developed parameters for manufacturing fully dense JBK-75 components using powder bed fusion additive manufacturing (PBFAM). These parameters were developed in a two-step development. First, the depth of laser penetration in the powdered material was measured across a spectrum of laser powers to determine the optimal power necessary for generating the desired meltpool depth. The parameter set’s vector-to-vector spacing was then then tailored to guarantee the full densification of the desired area. The results of this development was a readily implementable parameter that produced 99.6% dense material when using a 147W power running at 600mm/s with a 85μm(32%) vector-to-vector spacing.

Jones, Z. C.↗

Circular Corrugated Miter Bend and Gap Losses for Broadband Frequency Applications

Circular corrugated waveguides are often used in fusion applications at single, multiple, or broadband millimeter frequencies due to their low ohmic loss, expected large frequency bandwidth, and direct coupling to free-space Gaussian modes. For single-frequency corrugated waveguide systems, transmission line components can be optimized to the desired frequency. For broadband or multiple-frequency applications, this is not possible. The goal of this paper is to demonstrate that the frequency bandwidth of circular corrugated waveguides can be compromised by diffraction losses to miter bends and gaps. It is shown that if the corrugation depth differs significantly from λ /4, a theory can substantially underpredict the gap and miter bend losses. The simulations are also shown to compare favorably to experimental measurements. To improve the transmission line performance in large frequency bandwidth systems, such as 33–165 GHz reflectometry, reducing the number of miter bends may, therefore, be necessary. For the improvement of performance in narrower frequency bandwidth or multiple-frequency systems, especially high-powered systems, wavelength-dependent techniques may be applicable. Furthermore, one such application is shown for a Bragg reflection technique to reduce the thermal load to insulating ceramic rings in a dc break component for multiple-frequency ITER electron cyclotron heating transmission lines.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Implosion performance of subscale beryllium capsules on the NIF

Many inertial fusion designs use capsules made of beryllium, as its high mass ablation rate is advantageous. here, we present the first systematic experimental study of indirectly driven beryllium capsules with a cryogenic deuterium-tritium fuel layer. “Subscale” capsules, 80% of the nominal National Ignition Facility point design radius, show optimal performance with the remaining mass of ~6–7%. A buoyancy-drag mix model explains the implosion performance, suggesting that fuel-ablator mix is the dominant degradation mechanism. Increasing the capsule scale is predicted to reduce the impact of fuel-ablator mix and achieve high performance.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Primary Edge Localized Mode Filament Structure in the National Spherical Torus Experiment

Recent studies on the DIII-D tokamak [J. L. Luxon, Nucl. Fusion 42, 614 (2002)] have elucidated key aspects of the dependence of stability, confinement, and density control on the plasma magnetic configuration, leading to the demonstration of nearly noninductive operation for >1 s with pressure 30% above the ideal no-wall stability limit. Achieving fully noninductive tokamak operation requires high pressure, good confinement, and density control through divertor pumping. Plasma geometry affects all of these. Ideal magnetohydrodynamics modeling of external kink stability suggests that it may be optimized by adjusting the shape parameter known as squareness (zeta). Optimizing kink stability leads to an increase in the maximum stable pressure. Experiments confirm that stability varies strongly with zeta, in agreement with the modeling. Optimization of kink stability via zeta is concurrent with an increase in the H-mode edge pressure pedestal stability. Global energy confinement is optimized at the lowest zeta tested, with increased pedestal pressure and lower core transport. Adjusting the magnetic divertor balance about a double-null configuration optimizes density control for improved noninductive auxiliary current drive. The best density control is obtained with a slight imbalance toward the divertor opposite the ion grad(B) drift direction, consistent with modeling of these effects. These optimizations have been combined to achieve noninductive current fractions near unity for over 1 s with normalized pressure of 3.5 65%, and a normalized confinement factor of H(98(y,2))approximate to 1.5.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Design and Overview of 100 kV Bushing for the DNB Injector of ITER

The 100 kV bushing is one of the most important and technologically challenging Safety Important Class (SIC) components of the Diagnostic Neutral Beam (DNB) injector of ITER. It forms interface between gas insulated electrical transmission line and torus primary vacuum and acts as a vacuum feedthrough of ITER. Design optimization has been carried out to meet the electric and structural requirements based on its classification. Unlike HNB bushing, single stage bushing is designed to provide 100 kV isolation. Finite Element Analysis (FEA) based optimization has been carried out for electrostatic and structural analysis. Manufacturing assembly sequence is studied and presented in this paper. However validation of the same is foreseen from manufacturer.

43 PARTICLE ACCELERATORS↗

The Path towards Plasma Facing Components: A Review of State-of-the-art in W-Based Refractory High-Entropy Alloys

Developing advanced materials for plasma-facing components (PFCs) in fusion reactors is a crucial aspect for achieving sustained energy production. Tungsten (W) - based refractory high-entropy alloys (RHEAs) have emerged as promising candidates due to their superior radiation tolerance and high-temperature strength. This review paper will focus on recent advancements in W-based RHEA research, particularly emphasizing the key role of modelling using machine learning (ML) in the stage of discovery by predicting properties for each composition and expediting the identification of optimal RHEA compositions with desired properties. Additionally, the application of additive manufacturing (AM) techniques for fabricating W-based RHEAs is explored, highlighting their advantages for rapid prototyping and multi-compositional sample production in a high throughput manner. The review critically evaluates the current understanding of mechanical properties relevant to PFC applications, including high-temperature strength and ductility. Furthermore, the radiation tolerance of W-based RHEAs under irradiated conditions is discussed. Finally, the validity of current AM-manufactured W-based RHEAs as PFC materials is assessed, and key challenges and opportunities for future research are identified. This review aims to provide a comprehensive overview of W-based RHEAs for fusion applications and their potential to guide the development and validation of advanced refractory high entropy alloys.

Hatler, Caleb [University of Wisconsin-Madison]↗

Integrated process modeling for the laser inertial fusion Energy (LIFE) generation system

A concept for a new fusion-fission hybrid technology is being developed at Lawrence Livermore National Laboratory. The primary application of this technology is base-load electrical power generation. However, variants of the baseline technology can be used to 'burn' spent nuclear fuel from light water reactors or to perform selective transmutation of problematic fission products. The use of a fusion driver allows very high burn-up of the fission fuel, limited only by the radiation resistance of the fuel form and system structures. As a part of this process, integrated process models have been developed to aid in concept definition. Several models have been developed. A cost scaling model allows quick assessment of design changes or technology improvements on cost of electricity. System design models are being used to better understand system interactions and to do design trade-off and optimization studies. Here we describe the different systems models and present systems analysis results. Different market entry strategies are discussed along with potential benefits to US energy security and nuclear waste disposal. Advanced technology options are evaluated and potential benefits from additional R&D targeted at the different options is quantified.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Spatial Statistical Data Fusion (SSDF)

As remote sensing for scientific purposes has transitioned from an experimental technology to an operational one, the selection of instruments has become more coordinated, so that the scientific community can exploit complementary measurements. However, tech nological and scientific heterogeneity across devices means that the statistical characteristics of the data they collect are different. The challenge addressed here is how to combine heterogeneous remote sensing data sets in a way that yields optimal statistical estimates of the underlying geophysical field, and provides rigorous uncertainty measures for those estimates. Different remote sensing data sets may have different spatial resolutions, different measurement error biases and variances, and other disparate characteristics. A state-of-the-art spatial statistical model was used to relate the true, but not directly observed, geophysical field to noisy, spatial aggregates observed by remote sensing instruments. The spatial covariances of the true field and the covariances of the true field with the observations were modeled. The observations are spatial averages of the true field values, over pixels, with different measurement noise superimposed. A kriging framework is used to infer optimal (minimum mean squared error and unbiased) estimates of the true field at point locations from pixel-level, noisy observations. A key feature of the spatial statistical model is the spatial mixed effects model that underlies it. The approach models the spatial covariance function of the underlying field using linear combinations of basis functions of fixed size. Approaches based on kriging require the inversion of very large spatial covariance matrices, and this is usually done by making simplifying assumptions about spatial covariance structure that simply do not hold for geophysical variables. In contrast, this method does not require these assumptions, and is also computationally much faster. This method is fundamentally different than other approaches to data fusion for remote sensing data because it is inferential rather than merely descriptive. All approaches combine data in a way that minimizes some specified loss function. Most of these are more or less ad hoc criteria based on what looks good to the eye, or some criteria that relate only to the data at hand.

Braverman, Amy J.↗

Assessing methods in fusion and fitting for time series construction in remote sensing-based earth observations

This study evaluates the comparative performance of spatiotemporal fusion and time-series fitting methods for constructing high-spatiotemporal-resolution remote sensing time-series data. Due to in-class similarity of fusion methods and fitting methods, we employ the Fit-FC (Fitting, spatial Filtering, and residual Compensation) model as a representative fusion method and the linear harmonic fitting model as a representative fitting method. Both Fit-FC and the linear harmonic fitting are widely used for high-spatiotemporal-resolution time-series data construction, and we modify the original Fit-FC model to enable automatic time-series fusion. To ensure data representativeness, we use 3 years (2019–2021) of Harmonized Landsat and Sentinel-2 surface reflectance datasets and Terra MCD43A4 products. Eight experimental regions are selected worldwide to guarantee generalization of the comparative performance between fusion and fitting methods, covering diverse land-use types (cropland, developed land, forest, and grassland) and varying climatological conditions. Time-series of NDVI and surface reflectance are analyzed under both actual observations and simulated data-missing scenarios. The constructed time-series data reveals that (1) the modified Fit-FC and linear harmonic fitting model achieve excellent performance in constructing high-resolution time-series images; (2) the fusion method outperforms the fitting method in constructing time-series of NDVI and surface reflectance images in cropland-, forest-, and grassland-dominated regions; (3) both methods achieve comparable performance in developed-dominated regions; (4) the fusion method is more robust to missing data, and better captures abrupt phenological transitions under conditions of continuous missing data; (5) the fitting method is computationally more efficient, making it suitable for large-scale time-series image reconstruction. This study provides valuable insights for selecting optimal strategies to generate high-resolution time-series images across diverse application scenarios and lays a foundation for extensions to other vegetation indices or land surface variables.

54 ENVIRONMENTAL SCIENCES↗

Optimization of Processing, Microstructure, and Hardness of an Al–Ce–Ni–Mn–Zr Alloy With Laser Additive Manufacturing

Here, this study examines the processing behavior, microstructure, surface roughness, and hardness properties of an aluminum alloy containing 8.2 Ce, 4.5 Ni, 0.5 Mn, and 0.7 Zr (wt%) fabricated using laser powder bed fusion. Sixty samples were produced across a range of laser powers, scan speeds, and hatch spacings to evaluate their effect on porosity, hardness, and microstructural features. Porosity was measured using X-ray computed tomography, while microstructure and surface roughness were characterized by scanning electron (SEM) and laser confocal microscopy. High dense and cracking-free Al–Ni–Ce alloy was successfully manufactured. Porosity showed a U-shaped dependence on energy input, increasing under both insufficient and excessive melting conditions. Hardness increased with cooling rate due to finer cellular structures and solute redistribution. A general statistical model was developed to capture the relationships between processing parameters and material response. Results identify a narrow processing window defined by laser powers between 350 and 370 W, scan speeds from 1400 to 1800 mm/s, and hatch distances between 0.14 and 0.18 mm. Within this window, porosity is minimized (below 0.01%) and hardness is maximized (up to 160 HV), demonstrating that careful control of these parameters enables dense, high strength aluminum components suitable for demanding structural applications.

Aluminum alloys↗

Final Report for completed IPP Project:"Development of Plasma Ablation for Soft Tissue and Bone Surgery"

ArthroCare is a medical device company that develops, manufactures, and markets an advanced surgical tool, a plasma electro-surgical system for cutting and removing tissue. The hand-held electrical discharge device produces plasma in a biocompatible conductive fluid and tissue to which it is applied during surgery. Its products allow surgeons to operate with increased precision and accuracy, limiting damage to surrounding tissue thereby reducing pain and speeding recovery for the patient. In the past, the design of ArthfoCare's plasma wands has been an empirical undertaking. One goal of this R&D program was to put the phenomena involved on a sound scientific footing, allowing optimization of existing plasma based electro-surgery system technology, and the design and manufacture of new and improved kinds of scalpels, in particular for the surgical cutting of bone. Another important related goal of the program was to develop, through an experimental approach, new plasma wand approaches to the cutting ('shaving') of hard bone tissue. The goals of the CRADA were accomplished - computer models were used to predict important parameters of the plasma discharge and the bone environment, and several different approaches to bone-shaving were developed and demonstrated. The primary goal of the project was to develop and demonstrate an atmospheric-pressure plasma tool that is suitable for surgical use for shaving bone in humans. This goal was accomplished, in fact with several different alternative plasma approaches. High bone ablation speeds were measured. The use of probes ('plasma wand' - the surgical tool) with moving active electrodes was also explored, and there are advantages to this method. Another important feature is that the newly-exposed bone surface have only a very thin necrosis layer; this feature was demonstrated. This CRADA has greatly advanced our understanding of bone removal by atmospheric pressure plasmas in liquid, and puts ArthroCare in a good position to develop the techniques for commercial (surgical) application.

43 PARTICLE ACCELERATORS↗

Development of a Direct Neutral Density Diagnostic for Fusion Edge Plasmas

As magnetically confined plasmas progress towards ignition and long pulse experiments, measurement and control of the neutral density in the plasma edge has become a critical issue for stability, formation of transport barriers, and fueling. Recent experiments by our research group have demonstrated that is possible to use two-photon absorption laser induced fluorescence (TA-LIF) to directly measure the density of neutral hydrogen in helicon sources and in the HIT-SI3 spheromak. While those experiments validated key elements of a diagnostic system that would enable similar measurements in tokamak plasmas, they did not fully address the issue of performance optimization in the presence of intense background light at the fluorescence wavelength and they also identified a number of other issues that must be resolved before successful TALIF neutral density measurements in a tokamak are likely to be achieved. Additional specific concerns raised during design reviews with the leadership of the DIII-D tokamak facility included: the minimum detection threshold for this TALIF diagnostic (currently ~ 5 x 10 15 m -3 ) and the rate at which neutral density measurements could be obtained. Improving the system performance to reduce the minimum detection threshold and demonstrating a faster rate of density determination are required to advance this diagnostic to the level where it could be considered for implementation on a major tokamak facility in the USA. The key issues that will be addressed through additional technological development are: validation of a new, chromatic aberration-free, xenon calibration scheme; increasing the output power of the laser; and suppression of background emission at the fluorescence wavelength through optimization of the collection optics and gating of the photomultiplier detector with a goal of obtaining a minimum detection threshold of 5 x 10 14 m -3 . Another key technological development, so far only tested in helicon source experiments, is the validation of Doppler-free TALIF as a means of obtaining higher speed, calibrated, neutral density measurements in tokamak-like conditions at the full cadence of the pulsed TALIF laser. In this work, we propose to complete these technological advancements through installation and testing of our prototype TALIF system on the proto-MPEX experiment at Oak Ridge National Laboratory (ORNL). The proto-MPEX facility will provide plasma conditions similar to the edge plasma of a major tokamak experiment but with pulse lengths and pulse repetition rates ideally suited for extensive development of a TALIF neutral density diagnostic. Measurement of the absolute neutral density in the edge of a magnetically confined plasma is necessary for plasma density control; calculation of charge-exchange power losses; control of plasma-wall interactions; determination of the braking of plasma flow; determination of the fuel mixture in deuterium-tritium plasma; and understanding the dynamics of the divertor region in the plasma edge. In terms of potential impact on the worldwide fusion program, we note that in burning plasma experiments, such as ITER, a 100 mJ/pulse Doppler-free TALIF diagnostic should be capable of directly measuring the deuterium/tritium (D/T) isotope ratio in the outer 0.5 to 1.0 m of the plasma radius. The D/T ratio is a critically important parameter for the control and optimization of burning plasmas. Therefore, development of the diagnostic system proposed here is also relevant to long-term US participation in diagnostic development for large tokamaks.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Exploring Sensitivity of ICF Outputs to Design Parameters in Experiments Using Machine Learning

We report building a sustainable burn platform in inertial confinement fusion (ICF) requires an understanding of the complex coupling of physical processes and the effects that key experimental design changes have on implosion performance. While simulation codes are used to model ICF implosions, incomplete physics and the need for approximations deteriorate their predictive capability. Identification of relationships between controllable design inputs and measurable outcomes can help guide the future design of experiments and development of simulation codes, which can potentially improve the accuracy of the computational models used to simulate ICF implosions. In this article, we leverage developments in machine learning (ML) and methods for ML feature importance/sensitivity analysis to identify complex relationships in ways that are difficult to process using expert judgment alone. We present work using random forest (RF) regression for prediction of yield, velocity, and other experimental outcomes given a suite of design parameters, along with an assessment of important relationships and uncertainties in the prediction model. We show that RF models are capable of learning and predicting on ICF experimental data with high accuracy, and we extract feature importance metrics that provide insight into the physical significance of different controllable design inputs for various ICF design configurations. These results can be used to augment expert intuition and simulation results for optimal design of future ICF experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Sub-divertor fuel isotopic content detection limit for JET and its impact on ICRF core heating and DTE2 operation

The ability to detect and control fuel isotopic content down to a 1% concentration level is greatly important for the upcoming JET DTE2 campaign, as well as its associated TT and DD phases. A reduction of H minority concentration even from 2% down to 1% is shown in this paper to have significant impact on the effectiveness of ion cyclotron range of frequencies core heating, while the ability to maintain T or D concentration at or below 1% is critical to limiting fusion neutron generation in the DD and TT phases, correspondingly. The sub-divertor measurement of (global) isotopic concentration, based on Penning-activated optical spectroscopy, can deliver minimally this 1% detection for DTE2 as long as light collection from the Penning emission can be optimized and gradual window transmission deterioration can be minimized. Here, this is simulated with a statistical analysis developed to understand the uncertainty sources in the JET DTE1 data, as well as to guide the optimization of an upgraded, fuel-isotopic content (and helium-ash concentration) gas analysis system for the JET divertor in preparation for DTE2. While this random error can be reduced to allow measurement substantially below 1% concentration, analysis also shows a systematic error of up to 1% understood to be due to plasma–surface interactions in the Penning excitation, suggesting that 1% may still be the low-end limit for the sub-divertor measurement, unless a Penning-source conditioning approach is also developed.

fusion fuel isotopic content↗

Plastic ablator ignition capsule design for the National Ignition Facility

The National Ignition Campaign, tasked with designing and fielding targets for fusion ignition experiments on the National Ignition Facility (NIF) [G. H. Miller, E. I. Moses, and C. R. Wuest, Nucl. Fusion 44, S228 (2004)], has carried forward three complementary target designs for the past several years: a beryllium ablator design, a plastic ablator design, and a high-density carbon or synthetic diamond design. This paper describes current simulations and design optimization to develop the plastic ablator capsule design as a candidate for the first ignition attempt on NIF. The trade-offs in capsule scale and laser energy that must be made to achieve a comparable ignition probability to that with beryllium are emphasized. Large numbers of one-dimensional simulations, meant to assess the statistical behavior of the target design, as well as two-dimensional simulations to assess the target's susceptibility to Rayleigh-Taylor growth are presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Experiments in DIII-D toward achieving rapid shutdown with runaway electron suppression

Experiments have been performed in the DIII-D tokamak [J. L. Luxon, Nucl. Fusion 42, 614 (2002)] toward understanding runaway electron formation and amplification during rapid discharge shutdown, as well as toward achieving complete collisional suppression of these runaway electrons via massive delivery of impurities. Runaway acceleration and amplification appear to be well explained using the zero-dimensional (0D) current quench toroidal electric field. 0D or even one-dimensional modeling using a Dreicer seed term, however, appears to be too small to explain the initial runaway seed formation. Up to 15% of the line-average electron density required for complete runaway suppression has been achieved in the middle of the current quench using optimized massive gas injection with multiple small gas valves firing simultaneously. The novel rapid shutdown techniques of massive shattered pellet injection and shell pellet injection have been demonstrated for the first time. Experiments using external magnetic perturbations to deconfine runaways have shown promising preliminary results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Accelerated version of NUBEAM capabilities in DIII-D using neural networks

A neural network model of the effects of neutral beam injection on DIII-D has been developed. The training and testing data used by the model have been generated by the NUBEAM module of TRANSP for experimental discharges from the 2018 DIII-D campaign. Using a principle component analysis to reduce the dimensionality of profile data, the model has been shown to reproduce the results of the Monte Carlo code NUBEAM with a high level of accuracy and an execution time orders of magnitude faster than the execution time of NUBEAM. Furthermore, this makes the neural network model uniquely suited to applications in model-based scenario planning (off-line) and active control (on-line), where a large number of simulation runs are required by the associated optimization tasks that need to be performed before and during the discharge.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Additive manufacturing of metal matrix composites

Although Metal matrix composites (MMCs) are superior to most sought-after metallic alloys, their challenging fabricability has limited their widespread use in bulk-form applications. Among the many advanced fabrication techniques, Additive Manufacturing (AM), owing to its unique capabilities to produce near-net shapes, has drawn significant traction in the past two decades, especially for materials that are difficult to process using traditional methods. However, unlike pure metal/alloy systems, MMCs are highly sensitive to the processing conditions prevailing in AM techniques due to factors such as the high melting point of reinforcement particles and the potential for in-situ reactions. Therefore, it may be a while before metal matrix composites are commercially produced via AM. This review will discuss the current state-of-the-art design, fabricability, and performance of various additively manufactured MMCs. A particular focus will be on microstructural evolution and microstructure-property relationships. The most employed AM techniques, such as directed energy deposition, powder bed fusion, binder jetting, sheet lamination, and solid-state friction stir processing, are fundamentally different in terms of thermo-kinetics, forming the perspective for this review. A detailed comparison of microstructural evolution and process parameter optimization, including feedstock preparation methods and the role of machine learning and modeling among the different AM processes, is also presented. Finally, a critical evaluation of emerging AM technologies for MMCs is also provided, highlighting their potential advantages and challenges.

36 - MATERIALS SCIENCE↗