Results for “microstructure characterization” — Page 57

DOE OSTI2022

A process optimization framework for laser direct energy deposition: Densification, microstructure, and mechanical properties of an Fe-Cr alloy

Laser Direct Energy Deposition (DED) is a metal additive manufacturing technique with the ability to fabricate large and complex parts through deposition of metal powders. However, achieving high-density parts and targeted build heights using DED can be challenging due to the large number of highly sensitive process variables. This work proposes a robust fabrication parameter optimization framework to generate process maps for primary parameters in DED, including laser power, scan speed, mass flow rate, hatch spacing, and layer height. Simple single-track experiments were utilized to map out the parameter space, and a combination of geometric criteria for hatch spacing and layer height were proposed to determine parameter sets that achieve both targeted build heights and mitigate porosity formation. Using this framework, specimens with >99 % density and consistent mechanical properties were successfully fabricated over a wide range of process parameters for an Fe-9wt.%Cr (Fe9Cr) alloy, a surrogate for radiation damage-resistant reduced activation ferritic/martensitic (RAFM) steels. Processing these materials using DED is of particular interest in the development of plasma facing components for nuclear fusion applications. The microstructure and mechanical properties of as-printed Fe9Cr were characterized using optical and electron microscopy, X-ray diffraction, and uniaxial tensile tests. As-printed Fe9Cr displayed ~25 % elongation and ultimate tensile strengths of up to 475 MPa which is comparable to similar wrought alloys. Finally, the proposed framework will allow for accelerated DED parameter optimization for novel alloy systems, as well as open the possibility for local microstructure control while simultaneously mitigating defect formation.

42 ENGINEERING↗

DOE OSTI2021

Advanced Fuels Campaign Execution Plan

The Advanced Fuels Campaign (AFC) Execution Plan outlines the strategy, mission, scope, near-term and long-term goals, structure, and organization associated with nuclear fuels and materials research, development, and demonstration activities within the Department of Energy’s (DOE) Nuclear Fuel Cycle and Supply Chain (NFCSC) program. NFCSC has been given responsibility to identify and mature advanced fuel technologies for the DOE using a science-based approach, focused on developing a fundamental understanding of nuclear fuels and materials to drive development of integrated nuclear fuel and materials technology. This science-based approach combines theory, experiments, and multiscale modeling and simulation to achieve a predictive understanding of relevant behaviors ranging from fuel fabrication processes (and their resulting fuel microstructures) through fuel/cladding performance under irradiation (in contrast to more empirical, observation-based approaches frequently used in fuel performance modeling and fuel qualification). The traditional scope of AFC includes the evaluation and development of multiple fuel forms to support two fuel cycle options: once-through and full recycle. The word “fuel” is used generically to include conventional fuels, transmutation targets, and any associated cladding or duct materials. The once-through fuel cycle addresses advanced light water reactor fuels with enhanced performance, extended burnup, and reduced waste generation. In fiscal year (FY) 2012, AFC’s scope expanded to include research, development, and demonstration (RD&D) for light water reactor (LWR) fuels with enhanced accident tolerance. Fuel fabrication activities include the development of innovative methods to enhance process efficiencies, reduce waste, and improve control over as-fabricated fuel microstructural properties to achieve desired in-reactor performance. Using modern modeling and simulation approaches, the objective is to predict fresh fuel properties given the feedstock characteristics and fabrication process parameters. The performance-related activities include small-scale, in-reactor, and out-of-reactor phenomenological testing (distinct from, but synergistic with, integral prototypic testing) and extensive, quantitative characterization (focusing on characterization of fuel and cladding materials at the scale of microstructure) both before and after testing. Larger-scale, prototypic experiments are conducted in concert with phenomenological testing to drive a Fuel Development and Qualification program, incorporating a fundamental understanding of fuel behavior performance characteristics. Then, using the tools developed under the productive science-based approach, fuels will be optimized to meet specific performance requirements, thereby minimizing the need to repeatedly perform large-scale, integral experiments over a wide parametric range as a means of experimental exploration. Two significant initiatives are underway within AFC. First, a gap analysis completed in early FY 2019 identified critical irradiation testing needs that are lacking within the national light water reactor (LWR) fuels testbed since the shutdown of the Halden Reactor in 2018. The identified gaps are for instrumented, prototypic testing of LWR fuels, especially under boiling water reactor conditions, ramp conditions, and conditions leading to fuel failure; these needs exist for supporting current LWR fuels and their possible extension to higher burnups, but are especially urgent relative to near-term development and qualification of accident-tolerant fuels. Recommendations that resulted from the Halden Gap Analysis focused on enhancements at Advanced Test Reactor (ATR) and Transient Reactor Test Facility (TREAT) to fill gaps in testing capabilities relative to these needs. Second, a concerted effort to develop and demonstrate a systematic approach to accelerating the development, testing, and qualification of new fuel systems has been initiated. This is highlighted by a test strategy that combines the considerable advances in multiscale, mechanistic fuel modeling of recent years with a MiniFuel separate effects test program in the High Flux Isotope Reactor (HFIR) and a Fission Accelerated Steady-state Testing (FAST) semi-integral accelerated test program in ATR. This approach is being tested/demonstrated using the metallic fuel system, but if successful it is expected to be extensible to multiple fuel types and diverse applications. This document includes an overview of the NFCSC program, a definition of science-based development of nuclear fuels, near-term goals for Advanced LWR fuels (ALFs), and longer-term goals for Advanced Reactor Fuels (ARFs) RD&D. This includes the activities that will be conducted to achieve success toward the grand challenge, as well as the goals and milestones to be achieved over the next few decades of research and development. Long-term goals are based on the DOE Office of Nuclear Energ

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Advanced Fuels Campaign Execution Plan

The Advanced Fuels Campaign (AFC) Execution Plan outlines the strategy, mission, scope, near-term and long-term goals, structure, and organization associated with nuclear fuels and materials research, development, and demonstration activities within the Department of Energy’s (DOE) Nuclear Fuel Cycle and Supply Chain (NFCSC) program. NFCSC has been given responsibility to identify and mature advanced fuel technologies for the DOE using a science-based approach, focused on developing a fundamental understanding of nuclear fuels and materials to drive development of integrated nuclear fuel and materials technology. This science-based approach combines theory, experiments, and multiscale modeling and simulation to achieve a predictive understanding of relevant behaviors ranging from fuel fabrication processes (and their resulting fuel microstructures) through fuel/cladding performance under irradiation (in contrast to more empirical, observation-based approaches frequently used in fuel performance modeling and fuel qualification). The traditional scope of AFC includes the evaluation and development of multiple fuel forms to support two fuel cycle options: once-through and full recycle. The word “fuel” is used generically to include conventional fuels, transmutation targets, and any associated cladding or duct materials. The once-through fuel cycle addresses advanced light water reactor fuels with enhanced performance, extended burnup, and reduced waste generation. In fiscal year (FY) 2012, AFC’s scope expanded to include research, development, and demonstration (RD&D) for light water reactor (LWR) fuels with enhanced accident tolerance. Fuel fabrication activities include the development of innovative methods to enhance process efficiencies, reduce waste, and improve control over as-fabricated fuel microstructural properties to achieve desired in-reactor performance. Using modern modeling and simulation approaches, the objective is to predict fresh fuel properties given the feedstock characteristics and fabrication process parameters. The performance-related activities include small-scale, in-reactor, and out-of-reactor phenomenological testing (distinct from, but synergistic with, integral prototypic testing) and extensive, quantitative characterization (focusing on characterization of fuel and cladding materials at the scale of microstructure) both before and after testing. Larger-scale, prototypic experiments are conducted in concert with phenomenological testing to drive a Fuel Development and Qualification program, incorporating a fundamental understanding of fuel behavior performance characteristics. Then, using the tools developed under the productive science-based approach, fuels will be optimized to meet specific performance requirements, thereby minimizing the need to repeatedly perform large-scale, integral experiments over a wide parametric range as a means of experimental exploration. Two significant initiatives are underway within AFC. First, a gap analysis completed in early FY 2019 identified critical irradiation testing needs that are lacking within the national light water reactor (LWR) fuels testbed since the shutdown of the Halden Reactor in 2018. The identified gaps are for instrumented, prototypic testing of LWR fuels, especially under boiling water reactor conditions, ramp conditions, and conditions leading to fuel failure; these needs exist for supporting current LWR fuels and their possible extension to higher burnups, but are especially urgent relative to near-term development and qualification of accident-tolerant fuels. Recommendations that resulted from the Halden Gap Analysis focused on enhancements at Advanced Test Reactor (ATR) and Transient Reactor Test Facility (TREAT) to fill gaps in testing capabilities relative to these needs. Second, a concerted effort to develop and demonstrate a systematic approach to accelerating the development, testing, and qualification of new fuel systems has been initiated. This is highlighted by a test strategy that combines the considerable advances in multiscale, mechanistic fuel modeling of recent years with a MiniFuel separate effects test program in the High Flux Isotope Reactor (HFIR) and a Fission Accelerated Steady-state Testing (FAST) semi-integral accelerated test program in ATR. This approach is being tested/demonstrated using the metallic fuel system, but if successful it is expected to be extensible to multiple fuel types and diverse applications. This document includes an overview of the NFCSC program, a definition of science-based development of nuclear fuels, near-term goals for Advanced LWR fuels (ALFs), and longer-term goals for Advanced Reactor Fuels (ARFs) RD&D. This includes the activities that will be conducted to achieve success toward the grand challenge, as well as the goals and milestones to be achieved over the next few decades of research and development. Long-term goals are based on the DOE Office of Nuclear Energ

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

Advanced Multiscale Microscopy Characterization of High Burnup LWR UO 2 Before and After LOCA Testing

Previous microscopy work within the campaign has observed increased porosity coupled with subgrain formation in the mid-radial region of the fuel. However, examinations of high burnup fuel taken from multiple reactors with different operating conditions have shown that this structure can move radially inward depending on the fuel operating conditions. It is currently theorized that inter- and intragranular fission gas bubble nucleation is precursory to the grain subdivision observed in the mid-radial and central regions of the fuel. Characterization of samples after loss-of-coolant accident (LOCA) testing has revealed that these restructured regions with a high density of bubbles and subgrains pulverize during the transient test. It appears that the increase in fission gas bubbles coupled with grain subdivision renders the fuel mechanically weaker during a LOCA transient and thus susceptible to fuel fragmentation relocation and dispersal (FFRD). Work this past fiscal year has prioritized understanding this behavior by using advanced microscopy to investigate fission gas behavior in the as-irradiated and post-LOCA state. Additional work has been performed to verify the theory described above by analyzing multiple post-LOCA optical micrographs and comparing that to as-irradiated microstructural data. This document reports progress in the post-irradiation characterization of high burnup nuclear fuel with emphasis on the restructured fuel regions, particularly how microstructural features influence FFRD and fission gas release behavior in LOCA conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS1992

Nonequilibrium synthesis of NbAl3 and Nb-Al-V alloys by laser cladding. I - Microstructure evolution

The evolution of the microstructure in NbAl3 synthesized by a laser cladding technique (a rapid solidification process, with cooling rates up to 10 exp 6 C/sec) is investigated, and the phases are identified using convergent beam electron diffraction. Two new metastable phases were identified and characterized in detail. The effect of adding V on the final microstructure was also investigated, and the various phase chemistries and the partitioning of different elements into different phases were studied.

Sircar, S.↗

NASA NTRS1990

A study of hydrogen environment effects on microstructure property behavior of NASA-23 alloy and related alloy systems

This work is part of the overall advanced main combustion chamber (AMCC) casting characterization program of the Materials and Processes Laboratory of the Marshall Space Flight Center. The influence of hydrogen on the tensile properties and ductility behavior of NASA-23 alloy were analyzed. NASA-23 and other referenced alloys in cast and hipped conditions were solution treated and aged under selected conditions and characterized using optical metallography, scanning electron microscopy, and electron microprobe analysis techniques. The yield strength of NASA-23 is not affected much by hydrogen under tensile tests carried at 5000 psig conditions; however, the ultimate strength and ductility properties are degraded. This implies that the physical mechanisms operating would be related to the plastic deformation process. The fracture surfaces characteristics of NASA-23 specimens tensile tested in hydrogen, helium, and air were also analyzed. These revealed surface cracks around specimen periphery with the fracture surface showing a combination of intergranular and transgranular modes of fracture. It is seen that the specimens charged in hydrogen seem to favor a more brittle fracture mode in comparison to air and helium charged specimens. The AMCC casting characterization program is to be analyzed for their hydrogen behavior. As a result of this program, the basic microstructural factors and fracture characteristics in some cases were analyzed.

Diwan, Ravinder M.↗

DOE OSTI2024

GRCop-42: Comparison between laser powder bed fusion and laser powder direct energy deposition

This study involves a comparative analysis of additively manufactured GRCop-42 specimens produced using two processes: laser-powder bed fusion (L-PBF) and laser powder direct energy deposition (LP-DED). The investigation characterizes a range of material attributes, including surface topography, internal defects, microstructural features, quasi-static mechanical properties, and fractographic characteristics. The findings demonstrate that, despite the specimens being fabricated with the same base material, the resulting material properties vary significantly between the two additive manufacturing processes. As such, material properties cannot be presumed to be uniform across different manufacturing methods. Consequently, material characterization must be conducted for individual manufacturing processes based on specific parameters.

36 MATERIALS SCIENCE↗

NASA NTRSDate not supplied

Synchrotron Tomography of SiC/SiC Minicomposites to Observe and Quantify Damage Evolution

Composite performance is dictated by its microstructure – property relationships. For example, the characteristic response of ceramic matrix composites (CMCs) depends on the distribution of its constituents (i.e. fibers, matrix, fiber coatings, matrix cracks, and voids). Micro x-ray computed tomography (micro-CT) provides an opportunity to characterize the distribution of these constituents and to quantify the CMC microstructure in three-dimensions. To this end, In-situ micro-CT was performed at the Advanced Light Source (ALS) in combination with uniaxial tensile testing on SiC/SiC minicomposites. This work will describe the tensile load-dependent damage evolution within the microstructure of the SiC/SiC CMC specimens. The results from the micro-CT datasets can be used to develop micromechanical models that effectively capture damage initiation and progression in CMCs. In addition, details regarding the segmentation tools and techniques employed to understand and quantify these large tomography datasets will be presented.

Ashley Hilmas↗

DOE OSTI2026

New perspectives on materials and device dynamics using time-resolved full-field diffraction X-ray imaging

Understanding how materials evolve during synthesis, processing, or device operation requires experimental access to structural dynamics across wide ranges of length and time scales, often in bulk samples or even within packaged devices. Time-resolved full-field diffraction X-ray microscopy has recently emerged as a powerful way to meet this need by combining the penetration and structural sensitivity of X-ray diffraction with objective-lens-based magnification, sensitive high-resolution X-ray imaging detectors, and pump-probe and real-time imaging strategies. Advances in full-field X-ray diffraction microscopy, often termed dark-field X-ray microscopy (DFXM), enable simultaneous imaging of extended fields of view while retaining crystallographic selectivity. Time-resolved DFXM promises to enable advances in materials processing and dynamics, electrochemical and photochemical processes, and the design of electronic devices. This Perspective summarizes the key instrumental concepts that define the performance of these methods, including the choice of imaging optics, detector considerations, and the impact of source time structure at synchrotron light sources and X-ray free-electron lasers (XFELs). We discuss the simultaneous use of complementary imaging modes that are increasingly used in practice. The early demonstrations of the potential of time-resolved DFXM include real-time defect and grain-boundary dynamics during metal annealing, stroboscopic imaging of functional devices with high strain sensitivity, and ultrafast pump-probe implementations at XFELs that directly visualize acoustic-wave propagation and energy dissipation in bulk crystals.

Dark-field X-ray microscopy↗

NASA NTRS1985

Impact wear of iron rich superalloys

The impact-sliding wear resistance of chill cast and aligned eutectic Fe-base superalloys against M42 and 17-4 PH steel counterface materials is examined. The aligned material tests were run with carbide fibers perpendicular to the counterface contact surface and the characterization focused on fracture processes as observed in the subsurface microstructure of the worn materials. Metallographic analyses were performed on specimens exposed to various numbers of repetitive impact load cycles, and for comparison, two other aligned composites were tested with the same fiber orientation under identical test conditions against hardened M42 tool steel. A strong improvement was found in wear resistance of an aligned eutectic structure as compared to the corresponding randomized chill cast structure. Experiments with the softer 17-4 counterface were characterized by transfer onto the Fe-base superalloy, and the cracks formed were oriented transverse to the relative sliding direction and occurred in a periodic fashion. Observations in subsurface regions of the worn materials indicated crack intergranularity with an occasional transgranular fracture of the M7C3 carbide phase.

Wayne, S. F.↗

DOE OSTI2026

Irradiation of UC1+x kernels using the MiniFuel vehicle: Microstructure, phase analysis, and initial post-irradiation examination

Uranium carbide is a candidate fuel form for a wide range of advanced reactors, including larger Generation IV reactors as well as small modular reactors and microreactors. However, its commercial deployment timeline faces challenges via traditional qualification approaches. To address this issue, an accelerated fission rate irradiation test was performed to collect basic fuel performance data to inform fuel performance models and potential future integral tests. Hyperstoichiometric UC (UC1+x) kernels were irradiated in the High Flux Isotope Reactor using the MiniFuel irradiation vehicle. The test matrix spanned two temperature regimes (700 °C and 800 °C) and burnup levels (1.8 % FIMA and 2.8 % FIMA). Between 21 and 63 kernels were tested at each unique temperature and burnup condition. As-fabricated microstructural analysis revealed a multiphase composition with UC, UC2, UC2−y, and U-C-O bearing phases for the irradiated kernels. Following irradiation, fission gas release, swelling, and microstructures were analyzed. Measured fission gas release was below 5 % for all irradiation conditions, reaching a maximum at the highest temperature and burnup condition. A binary swelling response was observed; the lower burnup and temperature conditions resulted in negligible swelling, but the higher burnup and temperature conditions produced significant anisotropic swelling and densification in a subset of kernels. The basic microstructural exams of kernels following irradiation were not capable of showing a correlation between kernels that exhibited excessive swelling and those that did not. Characterization of a subset of samples using the Advanced Photon Source and more detailed microstructural examination of unirradiated kernels revealed that a subset of kernels contained very high UC2 phase fractions. The anomalous swelling response is hypothesized to have been driven by this chemical variation. The results of this irradiation highlight the potential of accelerated fission rate irradiation testing to explore such behaviors and inform the development of fuel specifications.

Adorno Lopes, Denise [ORNL] (ORCID:000900023705987↗

NASA NTRS1986

Directional solidification and annealing of Mn55Al45 alloys

The use of directional solidification to produce aligned or magnetic microstructures for the MnAl alloy and the effect of annealing on the bulk magnetic properties of the alloy are investigated. The phase composition, cylindrically shaped magnetization, and room-temperature magnetization of the samples are analyzed. The microstructure of a directionally solidified Al-Mn alloy is characterized by a two-phase structure consisting of randomly-oriented Al-rich fibers of about 40 at. pct Al dispersed in a textureless matrix of about 50 at. pct Al; the matrix phase contains at least 50 wt pct of the metastable and ferrimagnetic tau-phase, and the Al-rich fibers as a precipitated Cr5Al8-type Al-Mn phase. Significant macrosegregation for the thermally stable growth-up orientation is detected. The data reveal that the annealing enhances the cell-like microstructure observed transverse of the solidification direction and increases remanent magnetization and intrinsic coercivity.

Pirich, Ronald G.↗

DOE OSTI2022

Effective Mass from Seebeck Coefficient

Abstract Engineering semiconductor devices requires an understanding of the effective mass of electrons and holes. Effective masses have historically been determined in metals at cryogenic temperatures estimated using measurements of the electronic specific heat. Instead, by combining measurements of the Seebeck and Hall effects, a density of states effective mass can be determined in doped semiconductors at room temperature and above. Here, a simple method to calculate the electron effective mass using the Seebeck coefficient and an estimate of the free electron or hole concentration, such as that determined from the Hall effect, is introduced here is the Seebeck effective mass, n H is the charge carrier concentration measured by the Hall effect ( n H = 1/ eR H , R H is Hall resistance) in 10 20 cm −3 , T is the absolute temperature in K, S is the Seebeck coefficient, and k B / e = 86.3 μV K −1 . This estimate of the effective mass can aid the understanding and engineering of the electronic structure as it is largely independent of scattering and the effects of microstructure (grain boundary resistance). It is particularly helpful in characterizing thermoelectric materials.

Snyder, Gerald Jeffrey↗

DOE OSTI2022

Damage Tolerance Assessment of Laser Clad Repairs of Coarse Grain Ti-6Al-4V

Background: Laser cladding offers a promising approach to repairing aviation components, with the ability to restore the geometric shape and the static and fatigue strength. Objective: The damage tolerance of a coarse grain Ti-6Al-4 V material is assessed via three sets of samples: (i) baseline, (ii) laser clad repaired, and (iii) laser cladding followed by heat treatment. Method: The specimens were subjected to fatigue loading using a marker band technique, in which cracks initiated from pre-defined laser slots and the small crack growth rates were measured by quantitative fractography. Additional characterization was performed on these samples, including hardness measurements, microstructure analysis, and multimodal residual stress analyses. Results: The region of the specimen undergoing laser cladding exhibited higher hardness values and a compressive residual stress, based on the slitting method. The samples subjected to heat treatment after cladding displayed negligible differences in grain size and minimal residual stress relaxation. Conclusions: The results demonstrated significant variability, with data demonstrating that cracks in the laser clad region (exhibiting the largest compressive residual stress) grew faster than cracks in the substrate region of the sample or in the baseline cases. Finally, these counterintuitive results are rationalized with additional analyses from synchrotron-based energy dispersive X-ray diffraction and high energy X-ray diffraction, demonstrating significant spatial variability in the residual elastic strains in the millimeter-sized prior β grains within the material.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Refining Microstructures in Additively Manufactured Al/Cu Gradients Through TiB 2 Inclusions

Here, the additive manufacture of compositionally graded Al/Cu parts by laser engineered net shaping (LENS) is demonstrated. The use of a blue light build laser enabled deposition on a Cu substrate. The thermal gradient and rapid solidification inherent to selective laser melting enabled mass transport of Cu up to 4 mm from a Cu substrate through a pure Al deposition, providing a means of producing gradients with finer step sizes than the printed layer thicknesses. Divorcing gradient continuity from layer or particle size makes LENS a potentially enabling technology for the manufacture of graded density impactors for ramp compression experiments. Printing graded structures with pure Al, however, was prevented by the growth of Al 2 Cu 3 dendrites and acicular grains amid a matrix of Al 2 Cu. A combination of adding TiB 2 grain refining powder and actively varying print layer composition suppressed the dendritic growth mode and produced an equiaxed microstructure in a compositionally graded part. Material phase was characterized for crystal structure and nanoindentation hardness to enable a discussion of phase evolution in the rapidly solidifying melt pool of a LENS print.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Synthesis of nickel selenide thin films for high performance all-solid-state asymmetric supercapacitors

As a significant semiconductor, nickel selenide shows enormous potential and extensive application prospects in the field of sensor, photocatalysis and supercapacitor. In this paper, nickel selenide (Ni 3 Se 2 , NiSe) thin films were successfully fabricated on stainless-steel sheet using a facile, effective electrodeposition technique. The morphologies, microstructures and chemical compositions of the thin films are characterized systematically. Electrochemical tests exhibit that the Ni3Se2 and NiSe possess high specific capacitance of 581.1 F/g and 1644.7 F/g, respectively. A flexible, all-solid-state asymmetric supercapacitor is assembled by utilizing NiSe film as positive electrode and activated carbon as negative electrode. The solid device delivers a high areal capacitance of 27.0 mF/cm 2 at the current density of 0.7 mA/cm 2 . Furthermore, the maximum volumetric energy density and power density of the NiSe//AC asymmetric SCs can achieve 0.26 mWh/cm 3 and 33.35 mW/cm 3 , respectively. The device shows robust cycling stability with 84.6% capacitance retention after 10000 cycles, outstanding flexibility and satisfactory mechanical stability. Moreover, two devices in series can light up a red light-emitting diode, which displayed great potential applications for energy storage.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2021

Early reactivity of sodium silicate-activated slag pastes and its impact on rheological properties

The fast loss of fluidity of sodium silicate-activated slag (SS-AAS) systems have been widely studied in the literature. In this study, the rheology of these cements has been correlated with the evolution of the reaction products formed over time. For this purpose, a combination of experimental characterization techniques, to study the pore solution composition and microstructure of SS-AAS pastes and thermodynamic calculations have been applied. The initial precipitation of ill-defined N-A-S-H and C-N-A-S-H producta leads to a fast increase of the storage modulus after 40 min of reaction. These products are formed from the reaction of the Na{sup +} ions and silicate ions of the activator with the Ca{sup 2+} and aluminate species dissolved from the slag. However, when a shear is applied, the structure breaks down and fluidity is recovered, that infers that the attractive forces between the particles are low at the early stages of hydration.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Optimizing Bendability and Hardness of Age-Hardenable Aluminum Sheets through Local Thermo-Mechanical Processing

This paper introduces a novel thermo-mechanical process to modify the local mechanical properties of 6xxx aluminum (Al-Mg-Si-Cu) alloy sheets. In this process, two pairs of rollers travel along the length of a sheet while locally bending and unbending it so that the final shape and thickness of the sheet remains unchanged. Room temperature bending/unbending (B/U) produces a deformation gradient through thickness and local hardening in both T4 and T6 sheets (with 41% and 18% greater Vickers hardness, respectively). High temperature bending/unbending performed at ~ 500°C via induction heating, produces significant improvements in local formability as measured by bend testing. Formability levels equivalent to the as-received T4 temper are achieved within the processed zones of T6 sheets with bend angles of ~ 150°, without disturbing the T6 temper in the remainder of the sheet. Finite element simulations and characterization explained the mechanical property improvements and the heterogenous microstructure with weakened Cube texture. Due to its similarity with the roller hemming process, and its compact dimensions, the apparatus developed for B/U has the potential for seamless integration with roller hemming robots to selectively process high strength aluminum sheet materials within mass-production settings.

Efe, Mert [BATTELLE (PACIFIC NW LAB)]↗