SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This paper reports recent single-event latchup results for a variety of microelectronic devices that include an digital, analog, and CMOS. The data was collected to evaluate these devices for possible use in NASA spacecraft.
The CMOS Radiation Effects Measurement (CREM) experiment is presently being flown on the Explorer-55. The purpose of the experiment is to evaluate device performance in the actual space radiation environment and to correlate the respective measurements to on-the-ground laboratory irradiation results. The experiment contains an assembly of C-MOS and P-MOS devices shielded in front by flat slabs of aluminum and by a practically infinite shield in the back. Predictions of radiation damage to C-MOS devices are based on standard environment models and computational techniques. A comparison of the shifts in CMOS threshold potentials, that is, those measured in space to those obtained from the on-the-ground simulation experiment with Co-60, indicates that the measured space damage is smaller than predicted by about a factor of 2-3 for thin shields, but agrees well with predictions for thicker shields.
The CMOS Radiation Effects Measurement (CREM) experiment is presently being flown on the Explorer-55, to evaluate device performance in the actual space radiation environment and to correlate the respective measurements to on-the-ground laboratory irradiation results. The experiment contains an assembly of CMOS and P-MOS devices shielded in front over 2 pi steradian by flat slabs of aluminum of 40, 80, 150, and 300 mils (1.02, 2.04, 3.81, and 7.62 mm) thicknesses, and by a practically infinite shield in the back. Initial results from the CREM experiment are reported. Predictions of radiation damage to CMOS devices are based on standard environment models and computational techniques. Measured space damage is smaller than predicted by about a factor of 2-3 for thin shields but agrees well with predictions for thicker shields. It is not clear at this time how the trapped particle environment models or the computational methods should be modified in order to achieve better agreement between experimental results and predicted damage curves.
Aluminum brazed titanium (ABTi) structures were evaluated during prolonged exposure to extreme environments: elevated temperature exposure to airline service fluids, hydraulic fluid, and seawater, followed by laboratory corrosion tests. Solid-face and perforated face honeycomb sandwich panel specimens, stressed panel assemblies, and faying surface brazed joints were tested. The corrosion resistance of ABTi is satisfactory for commercial airline service. Unprotected ABTi proved inherently resistant to attack by all of the extreme service aircraft environments except: seawater at 700 K (800 F) and above, dripping phosphate ester hydraulic fluid at 505 K (450 F), and a marine environment at ambient temperature. The natural oxides and deposits present on titanium surfaces in airline service provide protection against hot salt corrosion pitting. Coatings are required to protect titanium dripping phosphate ester fluid at elevated temperatures and to protect exposed acoustic honeycomb parts against corrosion in a marine environment.
The Low-Cost Solar Array (LSA) Project at the Jet Propulsion Laboratory has as one objective: the development and implementation of environmental tests for flat plate photovoltaic modules as part of the Department of Energy's terrestrial photovoltaic program. Modules procured under this program have been subjected to a variety of laboratory tests intended to simulate service environments, and the results of these tests have been compared to available data from actual field service. This comparison indicates that certain tests (notably temperature cycling, humidity cycling, and cyclic pressure loading) are effective indicators of some forms of field failures. Other tests have yielded results useful in formulating module design guidelines. Not all effects noted in field service have been successfully reproduced in the laboratory, however, and work is continuing in order to improve the value of the test program as a tool for evaluating module design and workmanship. This paper contains a review of these ongoing efforts and an assessment of significant test results to date.
The data base for composite materials' properties as they are affected by the environments encountered in operating conditions, both in flight and at ground terminals is expanded. Absorbed moisture degrades the mechanical properties of graphite/epoxy laminates at elevated temperatures. Since airplane components are frequently exposed to atmospheric moisture, rain, and accumulated water, quantitative data are required to evaluate the amount of fluids absorbed under various environmental conditions and the subsequent effects on material properties. In addition, accelerated laboratory test techniques are developed are reliably capable of predicting long term behavior. An accelerated environmental exposure testing procedure is developed, and experimental results are correlated and compared with analytical results to establish the level of confidence for predicting composite material properties.
Shuttle payload acoustic environmental predictions for the Jet Propulsion Laboratory's Galileo and Wide Field/Planetary Camera projects have been developed from STS-2 and STS-3 flight data. This evaluation of actual STS flight data resulted in reduced predicted environments for the JPL shuttle payloads. Shuttle payload mean acoustic levels were enveloped. Uncertainty factors were added to the mean envelope to provide confidence in the predicted environment.
The impact of various flight-related tasks on the workload imposed by the requirement to compute new headings, course changes, and reciprocal headings was investigated. Eight pilots were presented with a series of heading-change tasks in a laboratory setting. Two levels of difficulty of each of three tasks were presented verbally and spatially. Performance was measured by evaluating the speed and accuracy of the responses. The subjective responses and objective measures of performance reflected a strong association between subjective experience and objective behavior. The reciprocal calculations were performed quickly and accurately throughout and were considered to be minimally loading. Subjective workload, percent correct and response times for the two course-change tasks varied significantly as a function of level of difficulty and display format, with no discernable speed/accuracy trade off.
The National Aeronautics and Space Administration Headquarters sponsored the Near-Earth-Object Interception Workshop hosted by the Los Alamos National Laboratory on 14-16 Jan. 1992 at the J. Robert Oppenheimer Study Center in Los Alamos, New Mexico. The Workshop evaluated the issues involved in intercepting celestial objects that could hit the Earth. It covered the technologies for acquiring, tracking, and homing, as well as those for sending interceptors to inspect, rendezvous with, land on, irradiate, deflect, or destroy them. This report records the presentations and technical options reviewed.
NASA has initiated a research program with the long-term objective of supporting the aerospace industry in addressing issues related to the aging commercial transport fleet. The interdisciplinary program combines advanced fatigue crack growth prediction methodology with innovative nondestructive examination technology with the focus on multi-site damage (MSD) at riveted connections. A fracture mechanics evaluation of the concept of pressure proof testing the fuselage to screen for MSD has been completed. Also, a successful laboratory demonstration of the ability of the thermal flux method to detect disbonds at riveted lap splice joints has been conducted. All long-term program elements have been initiated and the plans for the methodology verification program are being coordinated with the airframe manufacturers.
From the Martin Marietta Astronautics Group base in Denver, Colorado, spacecraft engineers have been operating the Magellan spacecraft for the past three and one half years, along with the Jet Propulsion Laboratory, for NASA. The spacecraft team in Denver is responsible for the health of the vehicle, from command generation to evaluation of engineering telemetry. Operation of the spacecraft's Attitude and Articulation Control Subsystem (AACS) has specifically posed several in-flight challenges. This system must provide accurate pointing of the spacecraft throughout each 3.2 hour orbit which typically consists of 5 - 9 discrete maneuvers. Preparation of bi-weekly command sequences, monitoring execution, and trending of subsystem performance is of paramount importance, but in-flight anomalies have also demanded the attention of AACS engineers. Anomalies are often very interesting and challenging aspects of a project, and the Magellan mission was no exception. From the first unsuccessful attempts to perform a starscan, to spacecraft safing events, much has been experienced to add to the `lessons learned' from this mission. Many of Magellan's in-flight experiences, anomalies, and their resolutions are highlighted in this paper.
In boiling high heat fluxes are possible driven by relatively small temperature differences, which make its use increasingly attractive in aerospace applications. The objective of the research is to develop ways to overcome specific problems associated with boiling in the low gravity environment by substituting the buoyancy force with the electric force to enhance bubble removal from the heated surface. Previous studies indicate that in terrestrial applications nucleate boiling heat transfer can be increased by a factor of 50, as compared to values obtained for the same system without electric fields. The goal of our research is to experimentally explore the mechanisms responsible for EHD heat transfer enhancement in boiling in low gravity conditions, by visualizing the temperature distributions in the vicinity of the heated surface and around the bubble during boiling using real-time holographic interferometry (HI) combined with high-speed cinematography. In the first phase of the project the influence of the electric field on a single bubble is investigated. Pool boiling is simulated by injecting a single bubble through a nozzle into the subcooled liquid or into the thermal boundary layer developed along the flat heater surface. Since the exact location of bubble formation is known, the optical equipment can be aligned and focused accurately, which is an essential requirement for precision measurements of bubble shape, size and deformation, as well as the visualization of temperature fields by HI. The size of the bubble and the frequency of bubble departure can be controlled by suitable selection of nozzle diameter and mass flow rate of vapor. In this approach effects due to the presence of the electric field can be separated from effects caused by the temperature gradients in the thermal boundary layer. The influence of the thermal boundary layer can be investigated after activating the heater at a later stage of the research. For the visualization experiments a test cell was developed. All four vertical walls of the test cell are transparent, and they allow transillumination with laser light for visualization experiments by HI. The bottom electrode is a copper cylinder, which is electrically grounded. The copper block is heated with a resistive heater and it is equipped with 6 thermocouples that provide reference temperatures for the measurements with HI. The top electrode is a mesh electrode. Bubbles are injected with a syringe into the test cell through the bottom electrode. The working fluids presently used in the interferometric visualization experiments, water and PF 5052, satisfy requirements regarding thermophysical, optical and electrical properties. A 30kV power supply equipped with a voltmeter allows to apply the electric field to the electrodes during the experiments. The magnitude of the applied voltage can be adjusted either manually or through the LabVIEW data acquisition and control system connected to a PC. Temperatures of the heated block are recorded using type-T thermocouples, whose output is read by a data acquisition system. Images of the bubbles are recorded with 35mm photographic and 16mm high-speed cameras, scanned and analyzed using various software packages. Visualized temperature fields HI allows the visualization of temperature fields in the vicinity of bubbles during boiling in the form of fringes. Typical visualized temperature distributions around the air bubbles injected into the thermal boundary layer in PF5052 are shown. The temperature of the heated surface is 35 C. The temperature difference for a pair of fringes is approximately 0.05 C. The heat flux applied to the bottom surface is moderate, and the fringe patterns are regular. In the image a bubble penetrating the thermal boundary layer is visible. Because of the axial symmetry of the problem, simplified reconstruction techniques can be applied to recover the temperature field. The thermal plume developing above the heated surface for more intensive heating is shown. The temperature distribution in the liquid is clearly 3D, and tomographic techniques have to be applied to recover the temperature distribution in such a physical situation. A sequence of interferometric images showing the temperature distribution around the rising bubble, recorded with a high-speed camera is shown. Again, the temperature distribution is 3D, and a more complex approach to the evaluation, the tomographic reconstruction has to be taken. Measurement of the temperature distribution from the fringe pattern temperature distributions that yield important information regarding heat transfer are determined. Two algorithms that allow the quantitative evaluation of interferometric fringe patterns and the reconstruction of temperature fields during boiling have been developed at the Heat Transfer Laboratory of the Johns Hopkins University. In the first algorithm the bubble is assumed to be axially symmetrical, which significantly reduces the computational effort for quantifying the temperature distribution around the bubble. For this purpose the thermal boundary layer around the bubble is divided into equidistant concentric shells, and the refractive index is assumed to be constant in each of the shells. Since large temperature gradients are expected in the vicinity of the bubble during boiling, the deflection of the light beam cannot be neglected in boiling experiments. Since the exit angle of the light beam is known, this allows to account for the deflections and phase shifts outside the boundary layer (in the bulk fluid and in the windows of the test cell). Three dimensional temperature distributions in the vicinity of the bubble are reconstructed using tomographic techniques. In tomography, the measurement volume is sliced into 2D planes. In the present study these planes are parallel to the heated surface. The objective is to determine the values of the field parameter of interest in form of the field function in these 2D planes. The field parameter is the change of the refractive index of the liquid in the measurement volume caused by temperature changes. By superimposing data for many 2D planes recorded at the same time instant, the 3D temperature distribution in the measurement volume is recovered.
The NASA Glenn Research Center is developing hydrogen based combined cycle propulsion technology for a single-stage-to-orbit launch vehicle application under a project called GTX. Rocket Based Combined Cycle (RBCC) propulsion systems incorporate one or more rocket engines into an airbreathing flow path to increase specific impulse as compared to an all rocket-powered vehicle. In support of this effort, an RBCC direct-connect test capability was established at the Engine Components Research Laboratory to investigate low speed, ejector ramjet, and initial ramjet operations and performance. The facility and test article enables the evaluation of two candidate low speed operating schemes; the simultaneous mixing and combustion (SMC) and independent ramjet stream (IRS). The SMC operating scheme is based on the fuel rich operations of the rocket where performance depends upon mixing between the rocket plume and airstream. In contrast, the IRS scheme fuels the airstream separately and uses the rocket plume to ignite the fuel-air mixture. This paper describes the test hardware and facility upgrades installed to support the RBCC tests. It also defines and discusses low speed technical challenges being addressed by the experiments. Finally, preliminary test results, including rocket risk mitigating tests, unfueled airflow tests, and the integrated system hot fire test will be presented.
The NASA Glenn Research Center is developing hydrogen based combined cycle propulsion technology for a single-stage-to-orbit launch vehicle application under a project called GTX. Rocket Based Combined Cycle (RBCC) propulsion systems incorporate one or more rocket engines into an airbreathing flow path to increase specific impulse as compared to an all rocket-powered vehicle. In support of this effort, an RBCC direct-connect test capability was established at the Engine Components Research Laboratory to investigate low speed, ejector ramjet, and initial ramjet operations and performance. The facility and test article enables the evaluation of two candidate low speed operating schemes; the simultaneous mixing and combustion (SMC) and independent ramjet stream (IRS). The SMC operating scheme is based on the fuel rich operations of the rocket where performance depends upon mixing between the rocket plume and airstream. In contrast, the IRS scheme fuels the airstream separately and uses the rocket plume to ignite the fuel-air mixture. This paper describes the test hardware and facility upgrades installed to support the RBCC tests. It also defines and discusses low speed technical challenges being addressed by the experiments. Finally, preliminary test results, including rocket risk mitigating tests, unfueled airflow tests, and the integrated system hot fire test will be presented.
Polycyclic aromatic compounds (PACs), a class of organic molecules whose structures are characterized by the presence of two or more fused aromatic rings, have been the subject of astrophysical interest for nearly two decades. Large by interstellar standards (from as few as 20 to perhaps as many as several hundred atoms), it has been suggested that these species are among the most abundant interstellar molecules impacting a wide range of astrophysical phenomena including: the ubiquitous family of infrared emission bands observed in an ever-increasing assortment of astronomical objects; the subtle but rich array of discrete visible/near-infrared interstellar molecular absorption features known as the diffuse interstellar bands (DIBs); the broad near-infrared quasi-continuum observed in a number of nebulae known as excess red emission (ERE); the interstellar ultraviolet extinction curve and broad '2200 Angstrom bump'; the heating/cooling mechanisms of interstellar clouds. Nevertheless, until recently a lack of good-quality laboratory spectroscopic data on PACs under astrophysically relevant conditions (i.e. isolated, ionized molecules; ionized molecular clusters, etc.) has hindered critical evaluation and extension of this model
NASA Ames Research Center and the U.S. Army Aeroflightdynamics Directorate (AFDD) [will] have performed initial flight evaluations of the Research Flight Control System (RFCS) that has been integrated into the Army/NASA Rotorcraft Aircrew Systems Concepts Airborne Laboratory (RASCAL) variable stability helicopter. The RASCAL, a highly modified JUH-60A Black Hawk helicopter, is a variable-stability, in-flight simulator that is designed to support flight research programs that leverage on the flight control and handling qualities design tools developed by the Army and NASA. These tools are used in the flight control design life cycle from initial concept definition, through simulation, and ultimately into flight on-board the RASCAL helicopter. The RASCAL will be used to validate methodologies for reducing design cycle costs for new or modified aircraft, and it will serve as a base for the investigation of new rotorcraft technology.
This paper describes the development and validation of a new methodology for assessing the deleterious effects of spaceflight on crew health and performance. It is well known that microgravity results in various physiological alterations, e.g., headward fluid shifts which can impede physiological adaptation. Other factors that may affect crew operational efficiency include disruption of sleep-wake cycles, high workload, isolation, confinement, stress and fatigue. From an operational perspective, it is difficult to predict which individuals will be most or least affected in this unique environment given that most astronauts are first-time flyers. During future lunar and Mars missions space crews will include both men and women of multi-national origins, different professional backgrounds, and various states of physical condition. Therefore, new methods or technologies are needed to monitor and predict astronaut performance and health, and to evaluate the effects of various countermeasures on crew during long duration missions. This paper reviews several studies conducted in both laboratory and operational environments with men and women ranging in age between 18 to 50 years. The studies included the following: soldiers performing command and control functions during mobile operations in enclosed armored vehicles; subjects participating in laboratory tests of an anti-motion sickness medication; subjects exposed to chronic hypergravity aboard a centrifuge, and subject responses to 36-hours of sleep deprivation. Physiological measurements, performance metrics, and subjective self-reports were collected in each study. The results demonstrate that multivariate converging indicators provide a significantly more reliable method for assessing environmental effects on performance and health than any single indicator.
The Measurements of Humidity in the Atmosphere and Validation Experiments (MOHAVE, MOHAVE-II) inter-comparison campaigns took place at the Jet Propulsion Laboratory (JPL) Table Mountain Facility (TMF, 34.5(sup o)N) in October 2006 and 2007 respectively. Both campaigns aimed at evaluating the capability of three Raman lidars for the measurement of water vapor in the upper troposphere and lower stratosphere (UT/LS). During each campaign, more than 200 hours of lidar measurements were compared to balloon borne measurements obtained from 10 Cryogenic Frost-point Hygrometer (CFH) flights and over 50 Vaisala RS92 radiosonde flights. During MOHAVE, fluorescence in all three lidar receivers was identified, causing a significant wet bias above 10-12 km in the lidar profiles as compared to the CFH. All three lidars were reconfigured after MOHAVE, and no such bias was observed during the MOHAVE-II campaign. The lidar profiles agreed very well with the CFH up to 13-17 km altitude, where the lidar measurements become noise limited. The results from MOHAVE-II have shown that the water vapor Raman lidar will be an appropriate technique for the long-term monitoring of water vapor in the UT/LS given a slight increase in its power-aperture, as well as careful calibration.