Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “in situ testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Metal–Oxide Interface Sites Created Using Atomic Layer Deposition and Tested for CO Oxidation

The performance of catalysts made out of Pt supported on TiO 2 thin films grown on SBA-15 (a silica mesoporous material) by atomic layer deposition (ALD) was characterized systematically by combining in situ infrared absorption spectroscopy (IR) with other techniques including electron microscopy and adsorption−desorption isothermal measurements. The titania films in the resulting high-surface-area catalysts were evenly distributed throughout the inner surface of the SBA-15 mesopores, and their thickness could be controlled at a submonolayer level, with 3 to 4 TiO 2 ALD cycles needed for the complete coverage of the silica sites. The titania films could be deposited either before or after adding the metal (Pt), which was dispersed in the form of small nanoparticles (NPs) approximately 4−6 nm in diameter, in order to exert some control on the density and nature of the Pt/TiO 2 interface sites. One important lesson deriving from this work is that such an order of deposition leads to significantly different catalysts in spite of the fact that most of their structural properties are similar. If the Pt is deposited on the titania films, the resulting metal NPs are slightly smaller than those grown on silica and display CO adsorption sites with lower surface Pt coordination numbers. On the other hand, when TiO 2 is deposited on the Pt/SBA-15 starting material, some titania grows on the metal and partially blocks its surface while also creating new interface sites where CO binds more weakly and displays lower C−O stretching frequencies. In terms of catalytic performance, the results from in situ IR CO site titration and kinetic measurements combined suggest a mechanism where CO first adsorbs on Pt atop sites and then migrates to Pt/TiO 2 interface sites, where oxidation takes place. Both types of sites appear to be similar in all the catalysts tested, but catalytic performance could be optimized by tuning their surface densities. Maximum catalytic activity was obtained when the TiO2 films were deposited first and with TiO 2 coverages of at least half a monolayer, that is, after at least 2 ALD cycles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRSDate not supplied

Impact Ice Adhesion at NASA Glenn: Current Experimental Methods and Supporting Measurements

When examining the literature on the adhesion strength of impact ice, there have been a wide range of methodologies tried to measure the required stresses to induce interfacial delamination. Utilizing the Icing Research Tunnel at the NASA Glenn Research Center to generate the impact ice required for this work, several different mechanical tests have been and are being developed to determine the stresses along the interface between ice and coupon. This set of tests includes the technical mature modified lap joint test which has been used to conduct ice adhesion studies through a wide sweep of icing conditions. To conduct in situ ice adhesion measurements inside of the Icing Research Tunnel, several new experiments are currently being developed to make ice adhesion measurements during and immediately after ice accretion. In addition to these experimental methods, several supporting measurement techniques have been developed to allow for a better understanding on the influence of icing cloud conditions on the mechanical behavior of impact ice. Digital image correlation has been successfully implemented to augment the data generated by the modified lap joint test with full field surface displacement and strain measurements which allow for insight into the deformation processes present during a test. Both optical microscopy of impact ice samples along with ice replication techniques have been used to study the grain structure of the impact ice. This has led to a deeper understanding of the results from the modified lap joint method and how the structure of impact ice changes as it is accreted during an icing spray. The freezing process of impact ice generated by supercooled liquid water is not a volume conserving process, which leads to the presence of residual strains along the interface between ice and substrate. These strains have been observed using both a simplified flat geometry and a representative airfoil. The data gathered by these experimental adhesion methods and supporting measurements allows for a comprehensive understanding on the behavior of impact ice which will be critical to the development of future ice shedding models.

Ice Adhesion↗
NASA NTRSDate not supplied

Impact Ice Adhesion at NASA Glenn: Current Experimental Methods and Supporting Measurements

When examining the literature on the adhesion strength of impact ice, there have been a wide range of methodologies tried to measure the required stresses to induce interfacial delamination. Utilizing the Icing Research Tunnel at the NASA Glenn Research Center to generate the impact ice required for this work, several different mechanical tests have been and are being developed to determine the stresses along the interface between ice and coupon. This set of tests includes the technical mature modified lap joint test which has been used to conduct ice adhesion studies through a wide sweep of icing conditions. To conduct in situ ice adhesion measurements inside of the Icing Research Tunnel, several new experiments are currently being developed to make ice adhesion measurements during and immediately after ice accretion. In addition to these experimental methods, several supporting measurement techniques have been developed to allow for a better understanding on the influence of icing cloud conditions on the mechanical behavior of impact ice. Digital image correlation has been successfully implemented to augment the data generated by the modified lap joint test with full field surface displacement and strain measurements which allow for insight into the deformation processes present during a test. Both optical microscopy of impact ice samples along with ice replication techniques have been used to study the grain structure of the impact ice. This has led to a deeper understanding of the results from the modified lap join method and how the structure of impact ice changes as it is accreted during an icing spray. The freezing process of impact ice generated by supercooled liquid water is not a volume conserving process, which leads to the presence of residual strains along the interface between ice and substrate. These strains have been observed using both a simplified flat geometry and a representative airfoil. The data gathered by these experimental adhesion methods and supporting measurements allows for a compressive understanding on the behavior of impact ice which will be critical to the development of future ice shedding models.

Ice Adhesion↗
DOE OSTI2020

Assessment of Dynamic Fracture in Ultra-High Performance Concrete Using Synchrotron X-ray Source

Ultra-high-performance concretes (UHPCs) retain higher ultimate (compressive) strengths and greater durability relative to traditional concrete materials. As a result, they are enabling construction materials for blast resistant structures, where a higher capacity for energy absorption is required. In past investigations, the strength of UHPCs was shown to retain a dependency on strain rate. Still, the failure mechanisms which govern this rate dependency have yet to be completely elucidated. In the current study, the dynamic fracture behavior of Cor-tuf UHPC was assessed, in-situ, using a Synchrotron X-ray source in phase contrast imaging (PCI) mode. Prior to testing, the material’s morphology was characterized using X-ray computed tomography (CT) and scanning electron microscopy (SEM). A polychromatic pulsed X-ray source, high-speed camera and Kolsky bar apparatus were used in tandem, to observe the transient failure modes. A pin was placed at the end of the incident bar to control the location of damage initiation, and tests were performed at a constant velocity of ~6 m/s. These test conditions were observed to yield cracks with median and/or cone like geometries. Despite the variation in the crack paths, a significant difference in peak load was not observed. The failure mode was also observed to depend on the microstructure of the concrete samples.

Kolsky bar↗
DOE OSTI2021

Investigating the relationship between radial pre-stress magnitude and ballistic projectile dwell in heavy confined ceramic targets

A series of bare silicon carbide ceramic armour disks were manufactured with high-strength steel containment to induce varying magnitudes of radial pre-stress. The induced radial stresses, ranging from 0 to 900 MPa, were measured via neutron diffraction and verified by comparison with numerical calculations. Four targets of each configuration, referred to as slip-fit, moderate pre-stress, and high pre-stress, were subject to ballistic testing with hemispherical-nose, tungsten heavy alloy long rod projectiles to determine the interface defeat transition velocity. In-situ diagnostics were unsuccessful in aiding the identification of interface defeat, necessitating a reliance on post-mortem assessment. A transition velocity of approx. 1000 m/s was identified for the unstressed target, increasing to approx. 1200 m/s for the pre-stressed configurations. No performance effect was discernible between the moderate (372 MPa) and high (899 MPa) pre-stress configurations, suggesting that an optimal performance may be achieved for lower pre-stress levels (i.e., <372 MPa). Additionally, the test results were compared with four semi-analytical predictions of interface defeat performance and good agreement was found, albeit with significant range in the model predictions.

42 ENGINEERING↗
DOE OSTI2021

A micromechanical hydro-mechanical-damage coupled model for layered rocks considering multi-scale structures

An anisotropic Hydro-Mechanical-Damage coupled model was established in the framework of thermodynamics for saturated layered rocks, which contain arbitrarily-distributed cracks of smaller scales and orientated bedding planes of much larger scales. Here, the proposed model considers the anisotropic damage growth and frictional sliding of cracks and shear sliding and dilatancy of bedding planes, as well as the interaction between cracks and bedding planes. Numerical implementation of the nonlinear coupled model was developed based on TOUGHREACT, which is a well-established simulator for multiphase fluid flow and reactive transport analysis. The proposed model was first validated with laboratory water injection test results on rock blocks, and then used to study the effects of injection rates, in situ stresses and bedding planes on fluid injection processes at the field scale, demonstrating the importance to consider the variation of multi-scale structures for better understanding the coupled Hydro-Mechanical responses in layered rocks.

58 GEOSCIENCES↗
NASA NTRS1973

Evaluation of submarine strain-gage systems for monitoring coastal sediment migration

Single and multiple strain-gage systems were respectively evaluated as in situ point and areal sensors for monitoring sand-height variations in coastal environments. Static loading tests indicate that gage response pressure is linear for sand heights up to 24 inches. Response pressures are a function of both sand height and aggregate density, with density being influenced by both sediment texture and degree of compaction. Poorer sediment sorting and greater compaction result in higher response pressures. Field tests in a beach foreshore environment indicate that the gage systems are effective qualitative instruments for monitoring long-period migration trends of beach sediments; whereas, short-period responses are not sufficiently reliable. The durability and compactness of the gage systems must be substantially increased for effective field operations. It is recommended that the systems' qualitative potentials be further developed, whereas their development as quantitative instruments be terminated. Further development should emphasize the construction of remote recording systems designed for semipermanent installation.

Shideler, G. L.↗
NASA NTRS1979

Feasibility of determining flat roof heat losses using aerial thermography

The utility of aerial thermography for determining rooftop heat losses was investigated experimentally using several completely instrumented test roofs with known thermal resistances. Actual rooftop heat losses were obtained both from in-situ instrumentation and aerial thermography obtained from overflights at an altitude of 305 m. In general, the remotely determined roof surface temperatures agreed very well with those obtained from ground measurements. The roof heat losses calculated using the remotely determined roof temperature agreed to within 17% of those calculated from 1/R delta T using ground measurements. However, this agreement may be fortuitous since the convective component of the heat loss is sensitive to small changes in roof temperature and to the average heat transfer coefficient used, whereas the radiative component is less sensitive. This, at this time, it is felt that an acceptable quantitative determination of roof heat losses using aerial thermography is only feasible when the convective term is accurately known or minimized. The sensitivity of the heat loss determination to environmental conditions was also evaluated. The analysis showed that the most reliable quantitative heat loss determinations can probably be obtained from aerial thermography taken under conditions of total cloud cover with low wind speeds and at low ambient temperatures.

Bowman, R. L.↗
NASA NTRS1980

Comparative rocket observations of ionospheric electric fields in the auroral oval

The ion drift technique of measuring ionospheric electric fields is compared to two other simultaneous measurements. Rocket measurements in the evening auroral oval are checked against a dual probe, also in situ, and the ground based STARE auroral radar. The technique is explained thoroughly as well as tested for its dependence on mass. Two evening auroral oval conditions were observed from Andoya, Norway in January and February 1977. The first flight, 18:1005, measured electric fields over a quiet pre-midnight discrete arc. An interesting plasma convection reversal was observed poleward of the arc. The subsequent 18:1004, samples a breakup phase aurora nearer local midnight.

Zanetti, L. J., Jr.↗
NASA NTRS2013

Towards Prognostics for Electronics Components

Electronics components have an increasingly critical role in avionics systems and in the development of future aircraft systems. Prognostics of such components is becoming a very important research field as a result of the need to provide aircraft systems with system level health management information. This paper focuses on a prognostics application for electronics components within avionics systems, and in particular its application to an Isolated Gate Bipolar Transistor (IGBT). This application utilizes the remaining useful life prediction, accomplished by employing the particle filter framework, leveraging data from accelerated aging tests on IGBTs. These tests induced thermal-electrical overstresses by applying thermal cycling to the IGBT devices. In-situ state monitoring, including measurements of steady-state voltages and currents, electrical transients, and thermal transients are recorded and used as potential precursors of failure.

Saha, Bhaskar↗
NASA NTRS2016

Fatigue Life of Postbuckled Structures with Indentation Damage

The fatigue life of composite stiffened panels with indentation damage was investigated experimentally using single stringer compression specimens. Indentation damage was induced on one of the two flanges of the stringer. The experiments were conducted using advanced instrumentation, including digital image correlation, passive thermography, and in-situ ultrasonic scanning. Specimens with initial indentation damage lengths of 37 millimeters to 56 millimeters were tested in fatigue and the effects of cyclic load amplitude and damage size were studied. A means of comparison of the damage propagation rates and collapse loads based on a stress intensity measure and the Paris law is proposed.

Davila, Carlos G.↗
NASA NTRS2016

Fatigue Life of Postbuckled Structures with Indentation Damages

The fatigue life of composite stiffened panels with indentation damage was investigated experimentally using single stringer compression specimens. Indentation damage was induced on one of the two flanges of each stringer. The experiments were conducted using advanced instrumentation, including digital image correlation, passive thermography, and in-situ ultrasonic scanning. Specimens with initial indentation damage lengths of 32 millimeters to 56 millimeters were tested quasi-statically and in fatigue, and the effects of cyclic load amplitude and damage size were studied. A means of comparison of the damage propagation rates and collapse loads based on a stress intensity measure and the Paris law is proposed.

Davila, Carlos G.↗
NASA NTRS2018

Cracking Problems and Mechanical Characteristics of PME and BME Ceramic Capacitors

Most failures in MLCCs are caused by cracking that create shorts between opposite electrodes of the parts. A use of manual soldering makes this problem especially serious for space industry. Experience shows that different lots of ceramic capacitors might have different susceptibility to cracking under manual soldering conditions. This simulates a search of techniques that would allow revealing capacitors that are most robust to soldering-induced stresses. Currently, base metal electrode (BME) capacitors are introduced to high-reliability applications as a replacement of precious metal electrode (PME) parts. Understanding the difference in the susceptibility to cracking between PME and BME capacitors would facilitate this process. This presentation gives a review of mechanical characteristics measured in-situ on MLCCs that includes flexural strength, Vickers hardness, indentation fracture toughness, and the board flex testing and compare characteristics of BME and PME capacitors. A history case related to cracking in PME capacitors that caused flight system malfunctions and mechanisms of failure are considered. Possible qualification tests that would allow evaluation of the resistance of MLCCs to manual soldering are suggested and perspectives related to introduction of BME capacitors discussed.

Reliability↗
NASA NTRS2010

TPSAS-NF1676L-10746-DND

This paper presents the design, development, and field testing of a high sensitivity ground-based Differential Absorption Lidar (DIAL) system that was developed under the NASA Instrument Incubator Program. The investigation presents a significant advancement towards the development of future CO2 profiling capability as it incorporates key elements of technologies needed for a future development of global CO2 measuring systems including: (1) 2-μm laser technologies that have been developed under a number of NASA programs including the Laser Risk Reduction Program (LRRP) (2) A novel high quantum efficiency (QE), high gain (without excess noise factor), and low noise phototransistor, and (3) Direct detection DIAL system using a large collection area receiver that is insensitive to speckle and coherence length effects from atmospheric turbulence that influences heterodyne detection systems. The objective of the project was a system TRL of 4, and the goal was TRL 5. Development and testing of the laser, new detector, and receiver systems during the project, integration into a complete lidar system into a trailer, field testing of system at West Branch, IA and comparison of the lidar CO2 measurements with in situ sensors advanced the system to a TRL of 5. The system demonstrated high vertical resolution CO2 profiling capability within the boundary layer and column measurements to long ranges. This is the first direct detection demonstration of a 2-micron CO2 DIAL high vertical resolution capability from instrument concept to field demonstration.

Syed Ismail↗
NASA NTRSDate not supplied

Geopolymer Concrete – A greener alternative on Earth and a feasible material for the Moon

This research is focused on designing in-situ-based concrete material for extraterrestrial construction. Five regolith lunar simulants varying in their compositions were tested and their mechanical performance tested. The results have shown that the lunar regolith simulants are feasible for such concrete technology but exhibit variability due to their mineralogy, amorphous (glass) content, and particle size and shape distributions.

Peter J Collins↗
NASA NTRSDate not supplied

Coordinated Analysis of Isotopically Anomalous Nanoglobules and Insoluble Organic Matter in Quick-Look Samples From Asteroid Bennu

Spectral characterization of B-type asteroid Bennu by the Origins, Spectral Interpretation, Resource Identification, and Security–Regolith Explorer (OSIRIS-REx) spacecraft indicated abundant organic matter with similarities to insoluble organic matter (IOM) in meteorites. IOM in chondritic samples occurs in multiple forms, including a fluffy morphology and submicron-sized rounded nanoglobules. Isotopic anomalies in H, C, and N have been observed in both morphologies and are postulated to result from low-temperature chemical reactions in the molecular cloud or outer protoplanetary disk [e.g., 2,3]. We tested the hypothesis that Bennu also contains such isotopically anomalous organic matter by conducting coordinated in situ analysis of “quick-look” samples collected from the avionics deck of the OSIRIS-REx sample canister. This study expands our understanding of the fundamental nature of Bennu and its pre-accretionary environment by investigating the morphologies and isotopic distribution of presolar organic matter in Bennu.

A N Nguyen↗
DOE OSTI2022

Platinum nanoparticle compression: Combining in situ TEM and atomistic modeling

The mechanical behavior of nanoparticles governs their performance and stability in many applications. However, the small sizes of technologically relevant nanoparticles, with diameters in the range of 10 nm or less, significantly complicate experimental examination. These small nanoparticles are difficult to manipulate onto commercial test platforms and deform at loads that are below the typical noise floor of the testing instruments. Here, we synthesized small platinum nanoparticles directly onto a mechanical tester and used a modified nanomanipulator to enhance load resolution to the nanonewton scale. We demonstrated the in situ compression of an 11.5-nm platinum nanoparticle with simultaneous high-resolution measurements of load and particle morphology. Molecular dynamics simulations were performed on similarly sized particles to achieve complementary measurements of load and morphology, along with atomic resolution of dislocations. The experimental and simulation results revealed comparable values for the critical resolved shear stress for failure, 1.28 and 1.15 GPa, respectively. Altogether, this investigation demonstrated the promise of, and some initial results from, the combination of atomistic simulations and in situ experiments with an unprecedented combination of high spatial resolution and high load resolution to understand the behavior of metal nanoparticles under compression.

42 ENGINEERING↗