Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fractional diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57

An approximate analysis of the diffusing flow in a self-controlled heat pipe.

Constant-density two-dimensional axisymmetric equations are presented for the diffusing flow of a class of self-controlled heat pipes. The analysis is restricted to the vapor space. Condensation of the vapor is related to its mass fraction at the wall by the gas kinetic formula. The Karman-Pohlhausen integral method is applied to obtain approximate solutions. Solutions are presented for a water heat pipe with neon control gas.

Somogyi, D.↗

C1 chondrites - Comparison and contrast to other meteorite types

The minerals of chondritic meteorites, particularly C2 and C3 are usually believed to be condensates of the (previously unfractionated) solar nebula. This implies two postulates: (1) that chemical reactions between phases ceased at various temperatures; and (2) that Ni and Fe were mobilized by diffusion in the solid state. An alternate explanation is proposed, which obviates the two postulates: chondritic minerals may have condensed, in equilibrium with their own vapors, from a fraction already separated from the solar nebula at low temperature and low pressure.

Herndon, J. M.↗

QSO X-ray spectra and the contribution of QSOs to the X-ray background radiation

It has been suggested that QSOs make up a substantial fraction of the unresolved X-ray background (XRB) in the 0.5-3 keV energy band. The XRB is poorly known at these energies due to contamination by diffuse galactic emission. The XRB spectrum is precisely measured above 3 keV, and the aggregate spectrum of the proposed contributors should match its form. Seyfert galaxies are thought to contribute 20-30 percent (3-10 keV), and they have been shown to have power-law energy indices of roughly 0.7. The 1-15 keV average spectrum of a sample of optically bright QSOs and a 90 percent confidence range is found for a power law index of 0.83 for N(H) of less than 3 x 10 to the 20th atoms per sq cm. It is also found that QSOs with spectra most consistent with these measurements can contribute about 30 percent at most of the 3-10 keV XRB, or else the remaining contributors have intriguing spectra which rise with energy up to 10 keV and fall sharply thereafter. Alternativey, the X-ray spectral shape of QSOs is a function of redshift and/or radio luminosity.

Worrall, D. M.↗

SCR and GCR exposure ages of plagioclase grains from lunar soil

The concentrations of solar wind implanted Ar-36 in mineral grains extracted from lunar soils show that they were exposed to the solar wind on the lunar surface for an integrated time of 10E4 to 10E5 years. From the bulk soil 61501 plagioclase separates of 8 grain size ranges was prepared. The depletion of the implanted gases was achieved by etching aliquot samples of 4 grain sizes to various degrees. The experimental results pertinent to the present discussion are: The spallogenic Ne is, as in most plagioclases from lunar soils, affected by diffusive losses and of no use. The Ar-36 of solar wind origin amounts to (2030 + or - 100) x 10E-8 ccSTP/g in the 150 to 200 mm size fraction and shows that these grains were exposed to the solar wind for at least 10,000 years. The Ne-21/Ne-22 ratio of the spallogenic Ne is 0.75 + or - 0.01 and in very good agreement with the value of this ratio in a plagioclase separate from rock 76535. This rock has had a simple exposure history and its plagioclases have a chemical composition quite similar to those studied. In addition to the noble gases, the heavy particle tracks in an aliquot of the 150 to 200 mm plagioclase separate were investigated and found 92% of the grains to contain more than 10E8 tracks/sq cm. This corresponds to a mean track density of (5 + or - 1) x 10E8 tracks/sq cm. The exploration of the exposure history of the plagioclase separates from the soil 61501 do not contradict the model for the regolith dynamics but also fail to prove it.

Etique, P.↗

Composite interstellar grains

The possibility that interstellar grains are composite collections of very small particles, loosely attached to one another, is investigated. The grains are assumed to include a substantial proportion of vacuum along with solid particles. The optical properties of the composite grains are calculated with the approximate 'Bruggeman mixing rule', and the extinction of the grain is calculated wih standard Mie theory. The derived cross sections are close to those of hollow spheres in which the constituents occupy the proper volume fractions, and the derived optical constants of the mixture also obey the Kramers-Kroenig relations. The calculated interstellar extinction law shows reasonable agreement with observations of the diffuse ISM over the 1500-0.12 micron wavelength range. The predicted albedo is 0.5-0.6. It is predicted that the visual extinction per H nucleus should increase slightly with R(V).

Mathis, John S.↗

Synchrotron emission as a tracer of the outflow in M82

The discovery of radio synchrotron emission from the outflow in M82 is reported. It is found that the outflow in M82 is visible in synchrotron radiation. IC losses are evident in the steepening of the radio spectrum, though this process is not a major contributor to the observed halo X-ray emission. Particle acceleration and/or diffusion in the wind may be important. Outflow speeds of 1000-3000 km/s are inferred from the spectral index profiles, which significantly exceeds the optically determined values. The fraction of the wind energy in the form of relativistic particles is consistent with a supernova origin. A termination shock produced by the intergalactic medium may be shaping the observed halo of M82.

Seaquist, E. R.↗

Preventing Molecular and Particulate Infiltration in a Confined Volume

Contaminants from an instrument's self-generated sources or from sources external to the instrument may degrade its critical surfaces and/or create an environment which limits the instrument's intended performance. Analyses have been carried out on a method to investigate the required purging flow of clean, dry gas to prevent the ingestion of external contaminants into the instrument container volume. The pressure to be maintained and the required flow are examined in terms of their effectiveness in preventing gaseous and particulate contaminant ingestion and abatement of self-generated contaminants in the volume. The required venting area or the existing volume venting area is correlated to the volume to be purged, the allowable pressure differential across the volume, the external contaminant partial pressure, and the sizes of the ambient particulates. The diffusion of external water vapor into the volume while it was being purged was experimentally obtained in terms of an infiltration time constant. That data and the acceptable fraction of the outside pressure into the volume indicate the required flow of purge gas expressed in terms of volume change per unit time. The exclusion of particulates is based on the incoming velocity of the particles and the exit flow speed and density of the purge gas. The purging flow pressures needed to maintain the required flows through the vent passages are indicated. The purge gas must prevent or limit the entrance of the external contaminants to the critical locations of the instrument. It should also prevent self- contamination from surfaces, reduce material outgassing, and sweep out the outgassed products. Systems and facilities that can benefit from purging may be optical equipment, clinical facilities, manufacturing facilities, clean rooms, and other systems requiring clean environments.

Scialdone, John J.↗

Analogies Between Colloidal Sedimentation and Turbulent Convection at High Prandtl Numbers

A new set of coarse-grained equations of motion is proposed to describe concentration and velocity fluctuations in a dilute sedimenting suspension of non-Brownian particles. With these equations, colloidal sedimentation is found to be analogous to turbulent convection at high Prandtl numbers. Using Kraichnan's mixing-length theory, we obtain scaling relations for the diffusive dissipation length delta(sub theta), the velocity variance delta u, and the concentration variance delta phi. The obtained scaling laws over varying particle radius alpha and volume fraction phi(sub ) are in excellent agreement with the recent experiment by Segre, Herbolzheimer, and Chaikin. The analogy between colloidal sedimentation and turbulent convection gives a simple interpretation for the existence of a velocity cut-off length, which prevents hydrodynamic dispersion coefficients from being divergent. It also provides a coherent framework for the study of sedimentation dynamics in different colloidal systems.

Tong, P.↗

Ablation, Thermal Response, and Chemistry Program for Analysis of Thermal Protection Systems

In previous work, the authors documented the Multicomponent Ablation Thermochemistry (MAT) and Fully Implicit Ablation and Thermal response (FIAT) programs. In this work, key features from MAT and FIAT were combined to create the new Fully Implicit Ablation, Thermal response, and Chemistry (FIATC) program. FIATC is fully compatible with FIAT (version 2.5) but has expanded capabilities to compute the multispecies surface chemistry and ablation rate as part of the surface energy balance. This new methodology eliminates B' tables, provides blown species fractions as a function of time, and enables calculations that would otherwise be impractical (e.g. 4+ dimensional tables) such as pyrolysis and ablation with kinetic rates or unequal diffusion coefficients. Equations and solution procedures are presented, then representative calculations of equilibrium and finite-rate ablation in flight and ground-test environments are discussed.

Milos, Frank S.↗

Phase-Field Modeling of Microstructure and Thermal Conductivity Evolution under Radiation

The major factors that influence the thermal conductivity of the ceramics and metals are temperature, stoichiometry, microstructure, porosity, and point defects. Nuclear fuels and structure materials are subject to a severe radiation environment and their properties, including thermal conductivity change significantly with time and irradiation level. In particular, the accumulation of fission products and the formation of He bubbles can decrease the heat transfer, leading to overheating of the fuel element. In this work, we use the phase-field method to study the effect of microstructural changes on thermal conductivity. We developed a phase-field model to simulate the He bubble formation and growth in a single/polycrystalline material with defects. The model takes into account the generation of gas atoms and defects, gas atom diffusivity inhomogeneity, gas atom segregation, and gas bubble nucleation. With the model, we simulated the gas bubble and temperature evolution, and calculated the effect of gas bubble volume fraction on effective thermal conductivity.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Reactive thermal waves in energetic materials

Reactive thermal waves (RTWs) arise in several energetic material applications, including self-propagating high-temperature synthesis (SHS), high explosive cookoff, and the detonation of heterogeneous explosives. In this paper I exmaine ideal RTWs, by which I mean that (1) material motion is neglected, (2) the state dependence of reaction is Arrhenius in the temperature, and (3) the reaction rate is modulated by an arbitrary mass-fraction-based reaction progress function. Numerical simulations demonstrate that one's natural intuition, which is based mainly upon experience with inert materials and which leads one to expect diffusion processes to become relatively slow after a short time period, is invalid for high energy, state-sensitive reactive systems. Instead, theory predicts that RTWs can propagate at very high speeds. This result agrees with estimates for detonating heterogeneous explosives, which indicate that RTWs must spread from hot-spot nucleation sites at rates comparable to the detonation speed in order to produce experimentally-observed reaction zone thicknesses. Using dimensionless scaling and further invoking the high activation energy approximation, I obtain an analytic formula for the steady plane RTW speed from numerical calculations. I then compute the RTW speed for real explosives, and discuss aspects of their behavior.

66↗

Fe/Mn in olivine of carbonaceous meteorites

Olivines in primitive meteorites show a range of Fe/Mn both within one grain and among grains suggesting that they have recorded changing conditions during or after growth. Because olivine should be an early forming phase, Fe/Mn is used here to infer these earliest conditions. Initial Fe/Mn in cores of isolated, euhedral forsterite in both C2 and C3 meteorites ranges from 25 to 35 but differs at grain edge. Murchison (C2) forsterites show Fe/Mn approaching 1.0 at the grain edge while Ornans Fe/Mn is near 60 at grain edge. These values are lower than the matrix Fe/Mn for both meteorites and the distinct difference in zoning profile indicates different processes operating during and after grain growth. The Fe/Mn of bulk samples from a particular source such as the Moon is nearly constant. Individual samples show variation suggesting that there is some fractionation of Mn from Fe. Minerals have their individual ranges of Fe/Mn which has been used to recognize different types of olivine within one meteorite. Extreme values of Fe/Mn below 1.0 occur in forsterite from some IDP's, UOC matrix, and C1 meteorites. There are apparently no detailed studies of Fe/Mn variation within single olivine grains. Forsterite grains in C2 and C3 carbonaceous chondrites show complex zoning, and the nearly pure forsterites (Fo greater than approximately 99.5) have high levels of some minor elements including Ti, Al, V, and Sc. There is disagreement on the original source of these grains and both chondrule and vapor growth have been proposed. In addition, there is clear evidence that diffusion has affected the outer margins but in some cases the whole grain. Within the cores, the FeO range is limited, and if growing under constant conditions, the Fe/Mn should be near constant as there is little fractionation of Mn from Fe by forsterite. Additionally, there are apparently no co-crystallizing phases as evidenced by a lack of common inclusions in the forsterites. These observations are now followed by analyses of isolated olivine grains in C2 and C3 meteorites.

Steele, Ian M.↗

Molecular Simulations of CO 2 and H 2 Solubility, CO 2 Diffusivity, and Solvent Viscosity at 298 K for 27 Commercially Available Physical Solvents

CO 2 and H 2 solubilities, CO 2 /H 2 solubility selectivities, CO 2 diffusivities, and solvent viscosities in 27 commercially available physical solvents at 298 K were calculated from molecular simulations using the CHARMM36 all-atom force field for most solvents, and the simulation results were compared with available experimental data in this report. The van der Waals radius parameters for solvents were slightly tuned to reproduce the experimental solvent density. The simulated CO 2 solubilities are comparable with the experimental data, with an average absolute difference of 28%. For the homologous compounds containing the –(OCH 2 CH 2 )– repeat unit, both simulated and experimental data show that CO 2 solubility decreases when the number of repeat units is increased; CO 2 solubilities in these homologous compounds exhibit almost a perfect positive linear correlation with the solvent free-volume fractions. The simulated H 2 solubilities and CO 2 /H 2 solubility selectivities are also comparable with the experimental data, with differences of 22% and 17%, respectively. The H 2 solubilities in all solvents researched here correlate very well with the solvent free-volume fractions, exhibiting a positive linear correlation coefficient of 0.84. Additionally, simulations show that CO 2 solubility decreases when the temperature is increased. In contrast, H 2 solubility increases at elevated temperature, which is partly due to the increased solvent free-volume fraction at elevated temperature. Lastly, although the viscosity difference tends to be large (30%–246%) between simulation and experiment, both simulated and experimental data exhibit a similar solvent viscosity trend. Furthermore, simulations show that CO 2 diffusivities in solvents are very strongly correlated with the solvent viscosities and the relationship between them is given by D$_{CO_{2}}$ = (2.6 ± 0.3) × 10 –9 /η solvent 0.59 ± 0.03.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Surface Properties of PEMFC Gas Diffusion Layers

The wetting properties of PEMFC Gas Diffusion Layers (GDLs) were quantified by surface characterization measurements and modeling of material properties. Single-fiber contact-angle and surface energy (both Zisman and Owens-Wendt) data of a wide spectrum of GDL types is presented to delineate the effects of hydrophobic post-processing treatments. Modeling of the basic sessile-drop contact angle demonstrates that this value only gives a fraction of the total picture of interfacial wetting physics. Polar forces are shown to contribute 10-20 less than dispersive forces to the composite wetting of GDLs. Internal water contact angles obtained from Owens-Wendt analysis were measured at 13-19 higher than their single-fiber counterparts. An inverse relationship was found between internal contact angle and both Owens-Wendt surface energy and % polarity of the GDL. The most sophisticated PEMFC mathematical models use either experimentally measured capillary pressures or the standard Young-Laplace capillary-pressure equation. Based on the results of the Owens-Wendt analysis, an advancement to the Young-Laplace equation is proposed for use in these mathematical models, which utilizes only solid surface energies and fractional surface coverage of fluoropolymer. Capillary constants for the spectrum of analyzed GDLs are presented for the same purpose.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

On the thermal coarsening and transformation of nanoscale oxide inclusions in 316L stainless steel manufactured by laser powder bed fusion and its influence on impact toughness

The thermal evolution of nanoscale oxide inclusions in 316L stainless steel (SS) manufactured by laser powder bed fusion additive manufacturing (AM) was explored. The size, chemical composition, morphology, and distribution of the oxides were characterized as the function of heat treatment conditions. The study revealed the mechanistic driving force of the rapid oxide coarsening during recrystallization. Ostwald ripening governs oxide coarsening. The active grain boundary-oxide interaction at the early stage of recrystallization accelerated oxide coarsening via enhanced solute diffusion along grain boundaries. Pipe diffusion along dislocation cellular boundaries has a negligible contribution to oxide coarsening. At high temperatures (T> 1065 °C), although lattice diffusion primarily controlled the oxide growth, the contribution from the grain-boundary diffusion was necessary. The transformation from MnSiO 3 to CrMn 2 O 4 took place in the un-recrystallized grains but was not observed when recrystallization started. The interaction of grain boundary and oxides during recrystallization resulted in a high fraction of oxides accumulated at grain boundaries. While oxide coarsening does not significantly alter the toughness value, grain-boundary oxides promote microvoid formation and intergranular fracture under Charpy impact in the recrystallized AM 316L SS.

36 MATERIALS SCIENCE↗

Retention of ion-implemented-xenon in olivine - Dependence on implantation dose

The diffusion of Xe in olivine, a major mineral in both meteorites and linear samples, was studied. Xe ions were implanted at 200 keV into single-crystal synthetic-forsterite targets and the depth profiles were measured by alpha particle backscattering before and after annealing for 1 hour at temperatures up to 1500 C. The fraction of implanted XE retained following annealing was strongly dependent on the implantation dose. Maximum retention of 100 percent occurred for an implanting dose of 3 x 10 to the 15th power Xe ions/sq cm. Retention was less at lower doses, with approximately more than or = 50 percent loss at one hundred trillion Xe ions/sq cm. Taking the diffusion coefficient at this dose as a lower limit, the minimum activation energy necessary for Xe retention in a 10 micrometer layer for ten million years was calculated as a function of metamorphic temperature. Previously announced in STAR as N83-18528

Melcher, C. L.↗

Magnetic properties and microstructure of Sm-Co/α-Fe nanocomposite thick film-magnets composed of multi-layers over 700 layers

We synthesized Sm-Co/α-Fe nanocomposite film-magnets, approximately 10 μm in thickness, composed of 780 layers by the pulse laser deposition method. Transmission electron microscopic observations revealed that the synthesized film is composed of Sm-Co and α-Fe layers with the well-controlled α-Fe thickness of approximately 10–20 nm, which is suitable one predicted by the micromagnetic simulation. In spite of the enhanced interlayer diffusion of Fe and Co by annealing for crystallization, the (BH){sub max} value of 100 kJ/m{sup 3} was obtained at the averaged compositions of Sm/(Sm + Co) = 0.16 and Fe/(Sm + Co + Fe) = 0.47. The α-Fe fraction for obtaining the highest (BH){sub max} value was smaller than that expected from the micromagnetic simulation. Although the annealing for crystallization lay the easy direction of magnetization in the plane, the film is not expected to have strong crystallographic texture.

36 MATERIALS SCIENCE↗

Evaluating the efficacy of aluminide coatings to improve oxidation resistance of high performance engine valve alloys

Increasing peak cylinder pressures and operating temperatures of turbo-charged internal combustion engines (ICEs) engines present new challenges for existing materials employed in engine exhaust valves. Oxidation induced degradation of current Ni based alloys for these components will be a life-limiting mechanism while strict cost margins in the automotive transportation industry further limit the choice of suitable candidate materials. Metallic diffusion aluminide coatings can provide a cost-effective way to improve the oxidation resistance of underlying materials. In this study, the high temperature oxidation behavior of diffusion nickel aluminide coatings on two Ni based alloys (commercially available alloy 31V and a developmental alloy) during cyclic oxidation behavior in air+10% H 2 O at 900 °C was investigated. A complete depletion of the beneficial Al-rich β-(NiFe)Al phase was observed in the coating on alloy 31V while a significant fraction of this phase was retained in the coating on the second alloy. A coupled thermodynamic-kinetic model showed that the disappearance of the Al-rich phase in the coating on 31V was mainly due to the combined effect of steeper chemical potential gradients of Al and Ti between the coating and the substrate and their faster diffusivities compared to the coated developmental alloy. Finally, a higher content of Fe was shown to support the retention of β-(NiFe)Al phase in the coating on the developmental alloy while the presence of Ti in the alloy was shown to be detrimental for long-term coating performance.

36 MATERIALS SCIENCE↗