Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flow testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57

Blending of Radioactive Salt Solutions in Million Gallon Tanks - 13002

Research was completed at Savannah River National Laboratory (SRNL) to investigate processes related to the blending of radioactive, liquid waste, salt solutions in 4920 cubic meter, 25.9 meter diameter storage tanks. One process was the blending of large salt solution batches (up to 1135 - 3028 cubic meters), using submerged centrifugal pumps. A second process was the disturbance of a settled layer of solids, or sludge, on the tank bottom. And a third investigated process was the settling rate of sludge solids if suspended into slurries by the blending pump. To investigate these processes, experiments, CFD models (computational fluid dynamics), and theory were applied. Experiments were performed using simulated, non-radioactive, salt solutions referred to as supernates, and a layer of settled solids referred to as sludge. Blending experiments were performed in a 2.44 meter diameter pilot scale tank, and flow rate measurements and settling tests were performed at both pilot scale and full scale. A summary of the research is presented here to demonstrate the adage that, 'One good experiment fixes a lot of good theory'. Experimental testing was required to benchmark CFD models, or the models would have been incorrectly used. In fact, CFD safety factors were established by this research to predict full-scale blending performance. CFD models were used to determine pump design requirements, predict blending times, and cut costs several million dollars by reducing the number of required blending pumps. This research contributed to DOE missions to permanently close the remaining 47 of 51 SRS waste storage tanks. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Subtask 2.5 – Syngas Testing of NETL's Advanced Precombustion CO2 Capture Solvent

U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL) on-site researchers have been examining and developing a novel solvent for precombustion capture that has the potential for improved performance and lower costs compared to Selexol™ and Rectisol®. In Subtask 2.5, the Energy & Environmental Research Center (EERC) conducted actual comparison tests on actual coal-derived syngas of a PEGDME (polyethylene glycol dimethyl ether) Selexol-type solvent and three other solvents provided by NETL. One was a new hybrid PEG–PDMS (poly[dimethylsiloxane]) solvent engineered by NETL. In addition, two commercially available chemicals that are projected to have good CO2 capture abilities were also selected for testing on actual coal-derived syngas. These tests were conducted in the EERC high-pressure fluid-bed gasifier (HPFBG) system utilizing an existing gas-sweetening absorption system (GSAS) to test the solvents. The four solvents tested were Solvent 1 – AGR II from Coastal Chemical Co., LLC, NETL Solvent 2 – XG-3229 Bis(methoxytriethyleneoxypropyl)hexamethyltrisiloxane, as manufactured by Gelast, Inc.; Solvent 3 – CASSH-1 (diethyl sebacate), procured from Sigma Aldrich; and Solvent 4 – TBP (tributyl phosphate), purchased from ThermoFisher Scientific. The solvents were all tested at a consistent syngas flow and composition at approximately 50 bar to make direct comparisons easier; two solvent flow rates which would bracket 90% CO2 capture; and, temperatures of 10°, 25°, 40°, and 55°C to determine the effects of temperature on CO2 uptake and CO2 to H2 selectivity. Figure E-1 shows the results for CO2 uptake and selectivity for the various solvents. These data show that the CO2 uptake for the Selexol-type solvent for the PEG-PDMS-3 and CASHH-1 solvents at higher operating temperatures around 40°C was better than the Selexol-type solvent was able to achieve at the lower operating temperature of 10°C. Selectivity of CO2 over H2 was at least as good as Selexol for the PEG-PDMS-3 solvent and even better than Selexol for the CASSH-1 solvent. The TBP solvent also displayed good CO2 uptake; however, CO2/H2 selectivity was worse than for the Selexol-type solvent. Operation of precombustion CO2 solvents at temperatures above ambient can provide a 2% process efficiency improvement along with a significant capital cost reduction since refrigeration and solvent dehydration equipment is not required. The excellent results from these tests warrant further longer-duration testing with one or both superior NETL-provided solvents to determine if longer-term exposure to any coal-derived syngas trace species may have an adverse impact on solvent performance. This project was funded through the EERC–DOE Joint Program on Research and Development for Fossil Energy-Related Resources Cooperative Agreement No. DE-FE0024233.

01 COAL, LIGNITE, AND PEAT↗

Vortex rings drive entrainment and cooling in flow induced by a spark discharge

Spark plasma discharges induce vortex rings and a hot gas kernel. We develop a model to describe the late stage of the spark-induced flow and the role of the vortex rings in the entrainment of cold ambient gas and the cooling of the hot gas kernel. The model is tested in a plasma-induced flow using density and velocity measurements obtained from simultaneous stereoscopic particle image velocimetry and background oriented schlieren. We show that the spatial distribution of the hot kernel follows the motion of the vortex rings, whose radial expansion increases with the electrical energy deposited during the spark discharge. Here, the vortex ring cooling model establishes that entrainment in the convective cooling regime is induced by the vortex rings and governs the cooling of the hot gas kernel, and the rate of cooling increases with the electrical energy deposited during the spark discharge.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Predicting Ice Sheet and Climate Evolution at Extreme Scales (PISCEES) Final Technical Report for effort at the University of Texas at Austin Award DE-SC0008083 March 2016 - August 2017

Mass loss from the Greenland and Antarctic ice sheets is accelerating. Although ice sheet models have improved in recent years, much work is needed to make these models robust and efficient on continental scales and to quantify uncertainties in their projected outputs. The University of Texas at Austin's role in the PISCEES project is to provide guidance on how best to apply uncertainty quantification strategies to evaluating uncertainties in simulations of Greenland and Antarctic contributions to sea level rise in response to environmental forcing. Here we report on several activities that involved project members at UTA including Section 2.1 where we provide a broader overview of challenges to use UQ methods on ice ow modeling. Within Section 2.2 we describe the progress and challenges that remain for implementing important aspects of our "end-to-end" UQ work flow. In sum, we had a break-through in realizing the potential for implementing Active Subspace strategies making use of existing experiments exploring the sensitivity of the Greenland ice sheet flow to uncertain basal traction parameters. Section 2.3 presents progress that is being made to explore the effect of uncertainties in bed topography on stability of Thwaites basin, West Antarctica, using the BISICLES ice flow model. This effort is joint with Dan Martin at LBNL and a graduate student being co-mentored by Jackson. The results provide a compelling test case for the BISICLES ice flow model to address an important science question concerning the role of uncertain boundary conditions on ice sheet contributions to sea level rise.

54 ENVIRONMENTAL SCIENCES↗

Application of high-order numerical schemes and Newton-Krylov method to two-phase drift-flux model

This study concerns the application and solver robustness of the Newton-Krylov method in solving two-phase flow drift-flux model problems using high-order numerical schemes. In our previous studies, the Newton-Krylov method has been proven as a promising solver for two-phase flow drift-flux model problems. However, these studies were limited to use first-order numerical schemes only. Moreover, the previous approach to treating the drift-flux closure correlations was later revealed to cause deteriorated solver convergence performance, when the mesh was highly refined, and also when higher-order numerical schemes were employed. In this study, a second-order spatial discretization scheme that has been tested with two-fluid two-phase flow model was extended to solve drift-flux model problems. In order to improve solver robustness, and therefore efficiency, a new approach was proposed to treating the mean drift velocity of the gas phase as a primary nonlinear variable to the equation system. With this new approach, significant improvement in solver robustness was achieved. With highly refined mesh, the proposed treatment along with the Newton-Krylov solver were extensively tested with two-phase flow problems that cover a wide range of thermal-hydraulics conditions. Satisfactory convergence performances were observed for all test cases. Numerical verification was then performed in the form of mesh convergence studies, from which expected orders of accuracy were obtained for both the first-order and the second-order spatial discretization schemes. Finally, the drift-flux model, along with numerical methods presented, were validated with three sets of flow boiling experiments that cover different flow channel geometries (round tube, rectangular tube, and rod bundle), and a wide range of test conditions (pressure, mass flux, wall heat flux, inlet subcooling and outlet void fraction).

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

A Nonstationary and Non-Gaussian Moving Average Model for Solar Irradiance

Historically, power has flowed from large power plants to customers. Increasing penetration of distributed energy resources such as solar power from rooftop photovoltaic has made the distribution network a two-way-street with power being generated at the customer level. The incorporation of renewables introduces additional uncertainty and variability into the power grid. Distribution network operation studies are being adapted to include renewables; however, such studies require high quality solar irradiance data that adequately reflect realistic meteorological variability. Data from satellite-based products are spatially complete, but temporally coarse, whereas solar irradiances exhibit high frequency variation at very fine timescales. We propose a new stochastic method for temporally downscaling global horizontal irradiance (GHI) to 1 min resolution, but we do not consider the spatial aspect due to limited availability of the in situ irradiance measurements. Solar irradiance's first and second-order structures vary diurnally and seasonally, and our model adapts to such nonstationarity. Empirical irradiance data exhibits highly non-Gaussian behavior; we develop a nonstationary and non-Gaussian moving average model that is shown to capture realistic solar variability at multiple timescales. We also propose a new estimation scheme based on Cholesky factors of empirical autocovariance matrices, bypassing difficult and inaccessible likelihood-based approaches. The model is demonstrated for a case study of three locations that are located in diverse climates through the United States. The model is compared against competitors from the literature and is shown to provide better uncertainty and variability quantification on testing data.

Cholesky factor↗

A Monte Carlo model for seeded atomic flows in the transition regime

A simple model for the numerical determination of separation effects in seeded atomic gas flows is presented. The model is based on the known possibility to provide a statistically convergent estimate of the exact solution for a linear transport equation using the test particle Monte Carlo method. Accordingly, the flow field of the main gas is preliminary calculated and as a second step the linear transport equations obtained by fixing the target distribution in the collision term of the Boltzmann equation for both main and minority components are solved. Both solutions are based on appropriately devised test particle Monte Carlo methods. The second step, the critical one in evaluating the separation effects, is exact and thereby completely free of numerical diffusion. The model is described in details and illustrated by 2D test cases of atomic separation in shock fronts.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Ultrafine grained structure and improved mechanical properties of low temperature friction stir spot welded 6061-T6 Al alloys

Highlights: • Friction stir spot welding of Al alloy was successfully done at low rotation speed. • The highest welding temperature was lower than 200 °C. • The average grain size of less than 500 nm was formed in the stir zone. • No hardness reduction of the HAZ region could be detected. • Shear tensile tests of the welds revealed a maximum shear load of about 5400 N. - Abstract: In this study, 1 mm thick 6061-T6 aluminum alloy plates were subjected to friction stir spot welding (FSSW) at a very low rotation speed of 30, 40 and 50 rpm, aiming to prevent the hardness reduction in the heat affected zone (HAZ) of this precipitate hardening Al joints. Two kinds of rotating tools, namely, one with a 1 mm long probe and the other one with a flat shoulder without a probe, were used and the corresponding force applied to the rotating tools was ranged from 4 to 8 tons. Under this special welding condition, the highest welding temperature was measured lower than 200 °C. As a result, no hardness reduction of the HAZ region could be detected and an ultrafine grain structure with a high density of dislocations was formed in the stir zone. The average grain size obtained in the stir zone was less than 500 nm for all the welds, which was much smaller than that in conventional FSSW processed 6061-T6 Al joints. In addition, no hook-like bonding ligaments were formed in the joints due to the very different material flows and the shear tensile tests showed that the spot welds prepared by the low speed FSSW can reach a maximum shear load of about 5400 N, much higher than those prepared by the conventional FSSW technique.

36 MATERIALS SCIENCE↗

Validating compositional fluid flow simulations using 4D seismic interpretation and vice versa in the SECARB Early Test—A critical review

We report on strengths and weaknesses of 4D seismic interpretation as a technique for monitoring carbon dioxide that was injected as part of a large scale test associated with commercial enhanced oil recovery (EOR) at Cranfield Field, Mississippi, USA. The goals of the monitoring effort are 1) to make measurements to verify that the CO 2 is contained in the reservoir according to operational designs and model predictions, and 2) that if there are deviations, to provide data which can be used to update the earth models and determine if any mitigation is needed. Our work uses a compositional numerical simulation to model CO 2 flow in the reservoir and compares the results with estimates of changes in seismic properties between a pre-injection and a survey after more than 2 million metric tons injected. The complicated physics of the problem in Cranfield field present challenges to seismic interpretations. These findings reflect partial agreement between the results of the numerical simulation and the seismic interpretations. Possible causes of discrepancies among the fluid flow model and multiple interpretations of the same seismic data sets performed with different work flows illuminates the types of uncertainties that should be considered to achieve the goals of monitoring.

4D seismic↗

Native Natural circulation in VERA

This work seeks to introduce a native natural circulation solver to VERA's thermohydraulics capabilities. This work begins with initial investigations into the viability of such a solver by determining the fundamental equations as well as necessary inputs. The method was then implemented in the form of a Python script coupled to CTF which was compared to TRACE. Once viability of the natural circulation solver was established, it was then implemented natively in MPACT for use with previously created simplified thermohydraulics solvers. This new implementation of the native natural circulation solver in MPACT is then tested for single physics problems for both a BWR and PWR single channel model and compared to TRACE where it shows an error of about 30% for BWRs and about 15% for PWRs. The solver is additionally tested for NuScale based models where it demonstrates an error to the reported flow rate of about 10%, resulting in an eigenvalue error of only 138 pcm when comparing fixed flow rate multiphysics runs. Finally, the solver is tested in multiphysics systems for a small PWR assembly, a small BWR assembly, and a full core approximate model of the NuScale design. In these multiphysics runs, it demonstrates no impact on multiphysics convergence stability, as well as negligible impact on runtimes. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

In-situ Photophysical Monitors and Corrective Algorithms for Photovoltaic Film Deposition and Rapid Thermal Processing in Scalable Roll-to-Roll Manufacturing

This project evaluated three photophysics-based approaches for in situ process monitoring of the scalable deposition of perovskite photovoltaic films. Based on stakeholder input and the results of laboratory trials and literature analysis, two techniques, angle resolved elastic light scattering (ARLS) and time-resolved photoluminescence (TRPL) were prototyped and demonstrated with a mixture of simulation, offline and online tests. Also, a hybrid gas flow and humidity control enclosure was constructed and demonstrated to stabilize the ambient conditions around the slot die deposition process and were demonstrated to meet the target humidity control in situ. Due in part to a delayed start and COVID-related lab restrictions and personnel changes, some of the milestones were not met. In spite of these challenges, however, both techniques were prototyped through several iterations and demonstrated significant promise for rapid in line perovskite characterization within the targeted characterization time windows and these techniques are under further development for use in DE-FOA000235:2357-1586. The TRPL system was fully mounted and demonstrated on the scaled slot die roll to roll and sheet coating systems at the Washington Clean Energy Testbeds (WCET). Motivated by significant internal and stakeholder interest, the successful prototyping achieved here, the ongoing need for in-situ characterization for the scale-up of perovskite manufacturing, and the benefits of in situ photophysical characterization for future funded process development research, we are continuing with the principle aims of the project to develop effect in situ photophysical probes for fast analysis of the optoelectronic and structural quality of sheet based and roll to roll process perovskites. TRPLS and ARLS probes proposed in the project are to be completed with external support from the Washington Research Foundation at the WCET. We are currently actively engaged in the acquisition of components and plan to complete and test the probes within three months. It is our intention that these probes will then be used in ongoing perovskite development with our research and commercialization partners including First Solar and other member of the US MAP consortium in future funded development work.

14 SOLAR ENERGY↗

Open-source MFIX-DEM software for gas–solids flows: Part I—Verification studies

With rapid advancements in computer hardware, it is now possible to perform large simulations of granular flows using the Discrete Element Method (DEM). As a result, solids are increasingly treated in a discrete Lagrangian fashion in the gas–solids flow community. In this paper, the open-source MFIX-DEM software is described that can be used for simulating the gas–solids flow using an Eulerian reference frame for the continuum fluid and a Lagrangian discrete framework (Discrete Element Method) for the particles. This method is referred to as the continuum discrete method (CDM) to clearly make a distinction between the ambiguity of using a Lagrangian or Eulerian reference for either continuum or discrete formulations. This freely available CDM code for gas–solids flows can accelerate the research in computational gas–solids flows and establish a baseline that can lead to better closures for the continuum modeling (or traditionally referred to as two fluid model) of gas–solids flows. In this paper, a series of verification cases is employed which tests the different aspects of the code in a systematic fashion by exploring specific physics in gas–solids flows before exercising the fully coupled solution on simple canonical problems. It is critical to have an extensively verified code as the physics is complex with highly-nonlinear coupling, and it is difficult to ascertain the accuracy of the results without rigorous verification. These series of verification tests set the stage not only for rigorous validation studies (performed in part II of this paper) but also serve as a procedure for testing any new developments that couple continuum and discrete formulations for gas–solids flows.

Computational fluid dynamics↗

Development of a compact x-ray particle image velocimetry for measuring opaque flows

A compact x-ray particle image velocimetry (PIV) system employing a medical x-ray tube as a light source was developed to measure quantitative velocity field information of opaque flows. The x-ray PIV system consists of a medical x-ray tube, an x-ray charge coupled device camera, a programmable shutter for a pulse-type x ray, and a synchronization device. Through performance tests, the feasibility of the developed x-ray PIV system as a flow measuring device was verified. To check the feasibility of the developed system, we tested a tube flow at two different mean velocities of 1 and 2 mm/s. The x-ray absorption of tracer particles must be quite different from that of working fluid to have a good contrast in x-ray images. All experiments were performed under atmospheric pressure condition. This system is unique and useful for investigating various opaque flows or flows inside opaque conduits.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

An Approach to Assessing the Added Mass for a Plate in a Channel

The Global Threat Reduction initiative (GTRI) was established by the National Nuclear Security Administration (NNSA) in 2004. One of the highlights of the program is to convert research and test reactors at home and abroad from Highly Enriched Uranium (HEU) to Low Enriched Uranium (LEU) fuels. By switching directly from HEU to LEU, an LEU reactor produces fewer neutrons than an HEU reactor, and in some cases, a direct switch from HEU to LEU results in the reactor being unable to achieve criticality. Under certain circumstances, criticality is achieved and the original neutron fluxes are restored with LEU fuel by adding more fuel elements to the core. Not all reactors, exemplified by the Advanced Test Reactor (ATR) at the Idaho National Lab (INL), have the luxury of simply adding more fuel to the core. In such cases, entirely new designs must be created and tested. The ATR utilizes plate type fuel. During the design and testing of the ATR fuel, flow induced vibrations were identified as potential source for experiment and fuel failure. Flow induced vibrations are problematic to solve because both the frequency of excitation and the modal frequencies of the object need to be determined. For the frequency of the object the frequency is often determined, either theoretically or experimentally without any influence of fluid. When a fluid is introduced, the fundamental frequency of an object can be greatly reduced allowing for resonance between the excitation frequency and the fundamental frequency of the plate. The consequence of such resonance is often failure of the component. Current methods for determining the frequency of a body immersed in a fluid requires the use of multi-physics software in order to determine (if at all possible) the frequency of the object. The work herein provides an alternative means of calculating the frequency of a plate by combining plate frequency theory to determine the added mass on the plate when in the presence of narrow channels. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Discrete Element Modeling Results of Proppant Rearrangement in the Cooke Conductivity Cell

The study of propped fracture conductivity began in earnest with the development of the Cooke cell which later became part of the initial API standard. Subsequent developments included a patented multicell design to conduct 4 tests in a press at the same time. Other modifications have been used by various investigators. Recent studies by the Stim-Lab proppant consortium have indicated that the flow field across a Cooke proppant conductivity testing cell may not be uniform as initially believed which resulted is significantly different conductivity results. Post test analysis of low temperature metal alloy injections at the termination of proppant testing prior to the release of the applied stress suggest that higher flow is to be expected along the sides and top of the proppant pack than compared to the middle of the pack. To evaluate these experimental findings, a physics-based two-dimensional (2-D) discrete element model (DEM) was developed and applied to simulate proppant rearrangement during stress loading in the Cooke conductivity cell and the resulting porosity field. Analysis of these simulations are critical to understanding the impact of modification to the testing cell as well as understanding key proppant conductivity issues such as how these effects are manifested in proppant concentration testing results. The 2-D DEM model was constructed to represent a realistic cross section of the Cooke cell with a distribution of four material properties, three that represented the Cooke cell (steel, sandstone,square rings), and one representing the proppant. In principle, Cooke cell materials can be approximated as assemblies of independent discrete elements (particles) of various sizes and material properties that interact via cohesive interactions, repulsive forces, and frictional forces. The macroscopic behavior can then be modeled as the collective behavior of many interacting discrete elements. This DEM model is particularly suitable for modeling proppant mechanical interactions subjected to an applied stress, where the experimental cell is represented as a cohesive body composed of a large number of discrete elements, and proppants can be modeled as the individual discrete particles with various sizes (following the proppant size distribution-density function used in the test) that exhibit no cohesive strength between the particles. Initial 2-D DEM modeling results suggest that proppant rearrangement and non-uniform stress distribution across the proppant pack results in significant non-uniform porosity distribution across the Cooke cell. Larger porosities develop along the edge of the proppant pack beneath the square ring seal and would result in a disproportionate higher flow field along these edges as compared to the middle of the proppant pack. These results suggest that reported conductivity values determined by the Cooke cell may be biased to overestimate the actual conductivity of the proppant at high stresses and that modifications to the standard Cooke cell will affect the magnitude of this bias.

03 NATURAL GAS↗

SIMULATION AND MOCKUP OF SNS JET-FLOW TARGET WITH WALL JET FOR CAVITATION DAMAGE MITIGATION

Pressure waves created in liquid mercury pulsed spallation targets at the Spallation Neutron Source (SNS) at Oak Ridge National Laboratory induce cavitation damage on the stainless steel target container. The cavitation damage is thought to limit the lifetime of the target for power levels at and above 1 MW. Severe through-wall cavitation damage on an internal wall near the beam entrance window has been observed in spent-targets. Surprisingly though, there is very little damage on the walls that bound an annular mercury channel that wraps around the front and outside of the target. The mercury flow through this channel is characterized by smooth, attached streamlines. One theory to explain this lack of damage is that the uni-directional flow biases the direction of the collapsing cavitation bubble, reducing the impact pressure and subsequent damage. The theory has been reinforced by in-beam separate effects data. For this reason, a second-generation SNS mercury target has been designed with an internal wall jet configuration intended to protect the concave wall where damage has been observed. The wall jet mimics the annular flow channel streamlines, but since the jet is bounded on only one side, the momentum is gradually diffused by the bulk flow interactions as it progresses around the cicular path of the target nose. Numerical simulations of the flow through this jet-flow target have been completed, and a water loop has been assembled with a transparent test target in order to visualize and measure the flow field. This paper presents the wall jet simulation results, as well as early experimental data from the test loop.

cavitation mercury target jet flow wall jet↗

Report on the Economic Optimization of a Demonstration Case for a Static N-R HES Configuration using RAVEN

The synthetic time history generation algorithm in RAVEN has been extensively tested and used to perform qualitative assessments of the statistical characteristics of the net demand vs. demand for different values of the penetration of wind generation. Reported results highlight the need to consider the impact of variable renewable on the electricity net demand profile, due to the increase in its volatility with increased wind penetration. This analysis provides a strong foundation for the modeling and simulation needs expressed under the "Nuclear-Renewable Hybrid Energy Systems" (NRHES) project. Following this confirmative analysis the entire stochastic optimization framework has been tested in a demo case. The case chosen is an optimization driven by profitability for a system composed by a nuclear plant and a hydrogen production industrial process. This type of economical analysis is aimed to assess the capability of a hybrid system to penetrate the current energy market. In this sense it differs from the approach suggested under NRHES, where a cost minimization approach is suggested. This analysis is instead aimed to show the flexibility of the developed framework, e.g. for the evaluation of retrofitting projects of already existing plants. The system considered is subject to variable prices of electricity, which are simulated using the algorithm for the production of synthetic time histories. The physical system is considered without inertia so that it can be replaced by dispatching rules based on the highest marginal profit. Two optimization problems have been considered, for the first the size of the nuclear power plant is fixed and the optimization variable is the capacity of the hydrogen production plant. For the second, both plant sizes are optimization parameters while the overall capital expenditure is caped. The economical figures of merits considered are the Internal Rate of Return (IRR) and/or Profitability Index (PI) for the first one (since no cap is placed on the investment size) and Net Present Value (NPV) and/or IRR for the second one where the capital expenditure is constrained. Economic input data concerning capital costs, size-scaling factors, and operational costs for both plants have been collected from literature in order to achieve a simulation as realistic as possible. More work will be needed to obtain even more realistic numbers, possibly from industrial partners, and considering market elasticity for the hydrogen market. In order to perform the optimization of the cases described above, the economical external RAVEN module (CashFlow) for financial analysis has been improved in flexibility and generality. Some improvements have also been made to the optimization algorithm for a more efficient treatment of the boundary constrains. In conclusion three major results have been obtained: a) collection of the economical parameters characterizing the nuclear power plants and hydrogen production plants, b) extension of the financial analysis module (CashFlow) to drive the calculation of all needed cash flow streams and c) the testing of the full framework in a nearly final configuration.

97 MATHEMATICS AND COMPUTING↗