Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “data movements”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57

Contributions of GRACE to Climate Monitoring

The NASA/German Gravity Recovery and Climate Experiment (GRACE) was launched in March 2002. Rather than looking downward, GRACE continuously monitors the locations of and precise distance between twin satellites which orbit in tandem about 200 km apart. Variations in mass near Earth's surface cause heterogeneities in its gravity field, which in turn affect the orbits of satellites. Thus scientists can use GRACE data to map Earth's gravity field with enough accuracy to discern month to month changes caused by ocean circulation and redistribution of water stored on and in the land. Other gravitational influences, such as atmospheric circulation, post-glacial rebound, and solid earth movements are either independently determined and removed or are negligible on a monthly to sub-decadal timescale. Despite its coarse spatial (>150,000 sq km at mid-latitudes) and temporal (approx monthly) resolutions, GRACE has enabled significant advancements in the oceanic, hydrologic, and cryospheric science, and has great potential for climate monitoring, because it is the only global observing system able to measure ocean bottom pressures, total terrestrial water storage, and ice mass changes. The best known GRACE results are estimates of Greenland and Antarctic ice sheet loss rates. Previously, scientists had estimated ice mass losses using ground and satellite based altimetry and surface mass balance estimates based on snowfall accumulation and glacier discharge. While such measurements are still very useful for their spatial detail, they are imperfectly correlated with large-scale ice mass changes, due to snow and ice compaction and incomplete spatial coverage. GRACE enables scientists to generate monthly time series of Greenland and Antarctic ice mass, which have confirmed the shrinking of the polar ice sheets, one of the most obvious and indisputable manifestations of climate change. Further, GRACE has located and quantified hot spots of ice loss in southeastern Greenland and western Antarctica. For 2002 to present, the rate of ice mass loss has been 200 to 300 GT/yr in Greenland and 70 to 210 GT/yr in Antarctica, and some scientists are suggesting that the rates are accelerating. Similarly, GRACE has been used to monitor mass changes in alpine glaciers. Tamisiea et al. first characterized glacier melt along the southern coast of Alaska, more recently estimated to be occurring at a rate of 84 GT/yr. Chen et al. estimated that Patagonian glaciers are melting at a rate of 28 GT/yr, and estimated that the high mountains of central Asia lose ice at a rate of 47 GT/yr. Tapley et al. and Wahr et al. presented the first GRACE based estimates of changes in column-integrated terrestrial water storage (TWS; the sum of ground-water, soil moisture, surface waters, snow, ice, and water stored in vegetation) at continental scales. Since then, dozens of studies have shown that GRACE based estimates of regional to continental scale TWS variations agree with independent information, and some innovative uses of GRACE data have been developed. Rodell et al. (2004) and Swenson and Wahr (2006) demonstrated that by combining GRACE derived terrestrial water storage changes with observations of precipitation and runoff in a river basin scale water budget, it was possible to produce new estimates of evapotranspiration and atmospheric moisture convergence, essential climate variables that are difficult to estimate accurately. Similarly, GRACE has been used to constrain estimates of global river discharge and the contribution of changes in TWS to sea level rise. Crowley et al. observed a negative correlation between interannual TWS anomalies in the Amazon and the Congo River basin. Yeh et al. and Rodell et al. estimated regionally averaged groundwater storage variations based on GRACE and auxiliary observations. Rodell et al. and Tiwari et al. applied that method to quantify massive groundwater depletion in northern India caused by over reliance on aquifers for irration, and Famiglietti et al. found a similar situation in California's Central Valley. Zaitchik et al. and Lo et al. described approaches to use GRACE to constrain hydrological models, enabling integration of GRACE data with other observations and achieving much higher spatial and temporal resolutions than GRACE alone. Such approaches are now supporting applications including drought and water resources monitoring. Oceanography has likewise benefitted from the independent nature of GRACE observations. One application is measurement of the mass component of sea level rise, which complements radar altimetry and in situ measurements. GRACE also measures ocean bottom pressures (OBP), which help to refine understanding and modeling of ocean circulation and the ocean's fresh water budget, among other things. For example, Hayakawa et al. showed that GRACE observes OBP patterns absent from the background models of oceanic variability. Morison et al. used GRACE to describe important decadal scale shifts in circulation and an ongoing trend of freshening of the western Arctic, important indicators of climate variability. The research of Song and Zlotnicki and Chambers and Willis on GRACE-derived ocean bottom pressures in the sub-polar gyre led to the discovery of an ENSO teleconnection and a long-term change in OBP in the North Pacific sub-polar gyre that was not predicted by an ocean model. Further, Chambers and Willis were able to identify an internal redistribution of mass between Atlantic and Pacific Oceans lasting at least six years, which was not predicted by ocean models and was the first direct evidence of sustained mass transport from one ocean basin to another on periods longer than a year. Boening et al. observed a record increase in OBP over part of the southeastern Pacific in late 2009 and early 2010, primarily caused by wind stress curl associated with a strong and persistent anticyclone and likely related to the concurrent Central Pacific El Nino. GRACE has far surpassed its 5-year design lifetime, but it will likely succumb to the aging of batteries and instrument systems sometime in the next few years. NASA has begun initial development of a follow-on to GRACE with very similar design, which could launch as soon as 2016 and would provide continuity in the data record while improving resolution slightly. Higher resolution time variable gravity missions are also on the drawing board .

Rodell, Matthew↗

Modeling Seismic Recordings of High-Frequency Guided Infrasound on Mars

NASA's Interior Exploration using Seismic Investigations, Geodesy and Heat Transport (InSight) mission records several high-frequency (>0.5 Hz) dispersive seismic signals on Mars. These signals are due to the acoustic-to-seismic coupling of infrasound generated by the entry and impact of meteorites. This dispersion property is due to infrasound propagating in a structured atmosphere, and we refer to this dispersive infrasound as guided infrasound. We propose to model the propagation of guided infrasound and the seismic coupling to the ground analytically; we use a 1D layered atmosphere on a three-layer solid subsurface medium. The synthetic ground movements fit the observed dispersive seismic signals well and the fitting indicates that the regolith beneath InSight is about 40-m in thickness. We also examine and validate the previously-published subsurface models derived from InSight ambient seismic vibration data.

58 GEOSCIENCES↗

Web-based Preprocessing and Visualization of 3D FIB Tomography Data for Nuclear Fuel Characterization

Three-dimensional (3D) focused ion beam (FIB) tomography enables reconstruction of internal nuclear fuel features that can't be fully evaluated through surface imaging alone. This capability supports characterization of fuel constituents and defects under thermal and irradiation conditions relevant to microreactor development. However, large tomography datasets can create data-handling, loading, and visualization challenges, especially when image-stack preparation and file conversion must be completed with separate tools. The Computational Ultraspatial Tomography Toolkit for High-Resolution Object Analysis Tools (CUTTRHOAT) is an open-source web application being developed to display FIB tomography datasets available through the Nuclear Research Data System (NRDS). The current alpha version requires prepared HDF5 datasets and has limited integrated data-preparation capabilities. This project improves CUTTHROAT by adding dataset-folder selection, automatic input detection, dataset scanning, missing-slice identification, blank-slice insertion, and image-stack-to-HDF5 conversion. Two applications will be compared: the baseline CUTTHROAT alpha workflow and the updated application containing the integrated data-handling and preprocessing functions. Evaluation will consider dataset detection accuracy, conversion success, loading time, rendering responsiveness, application stability, and user interaction. Preliminary results demonstrate successful loading of existing HDF5 files and converted image stacks, while testing also identified performance reductions caused by excessive blank-slice generation. The updated workflow reduces reliance on external preparation tools and supports more direct movement from image stacks to color-code 3D visualization. Future work includes refining missing-slice handling, integrating additional preprocessing functions, like a denoising feature, parsing TIFF metadata for automatic voxel scaling, and adding manual X, Y, and Z voxel-spacing inputs for PNG and JPEG.

36 - MATERIALS SCIENCE↗

The Natural Thermoluminescence of Meteorites: Ordinary Chondrites at the Allan Hills Ice Fields - Part 5

Natural thermoluminescence (TL) data have been obtained for 167 ordinary chondrites from the ice fields in the vicinity of the Allan Hills in Victoria Land, Antarctica, in order to investigate their thermal and radiation history, pairing, terrestrial age, and concentration mechanisms. Using fairly conservative criteria (including natural and induced TL, find location, and petrographic data), the 167 meteorite fragments are thought to represent a maximum of 129 separate meteorites. Natural TL values for meteorites from the Main ice field are fairly low (typically 5-30 krad, indicative of terrestrial ages of approx. 400 ka), while the Far western field shows a spread with many values 30-80 krad, suggestive of less then 150-ka terrestrial ages. There appear to be trends in TL levels within individual ice fields which are suggestive of directions of ice movement at these sites during the period of meteorite concentration. These directions seem to be confirmed by the orientations of elongation preserved in meteorite pairing groups. The proportion of meteorites with very low natural TL levels (less then 5 krad) at each field is comparable to that observed at the Lewis Cliff site and for modern non-Antarctic falls and is also similar to the fraction of small perihelia (less then 0.85 AU) orbits calculated from fireball and fall observations. Induced TL data for meteorites from the Allan Hills confirm trends observed for meteorites collected during the 1977/1978 and 1978/1979 field seasons which show that a select group of H chondrites from the Antarctic experienced a different extraterrestrial thermal history to that of non-Antarctic H chondrites.

Benoit, Paul H.↗

Hurricanes alter 10 Be concentrations in tropical river sediment but do not change regional erosion rate estimates

Tropical islands, including many in island arcs, are subjected to recurring disturbances from extreme storms such as tropical cyclones. To test whether such storms influence cosmogenic nuclide concentrations such that they do not reflect long-term rates of erosion, we measured meteoric and in situ 10Be in river sediment samples from Dominica, an andesitic island in the Caribbean, before and after category five Hurricane Maria (2017). Populations of before- and after-storm concentrations are statistically indistinguishable (n=7 pairs for in situ 10 Be, n=11 pairs for meteoric 10 Be). 10 Be concentrations vary from -138% to +73% within before-after sample pairs relative to the mean of the pair. These new data suggest that the effects of extreme storms on the depth and amount of near-surface erosion on Dominica vary spatially. Our data support calculations of Niemi, et al. (2005) and Yanites, et al. (2009) suggesting that basin-by-basin comparisons of erosion rates based on cosmogenic nuclides should be approached with caution in small (<~100 km 2 ) watersheds affected by mass movements and extreme storms. Erosion rates determined from in situ 10Be in Dominica (geometric mean=0.102 mm y-1, n=12) are low compared to similarly steep and wet areas globally and correlate positively with the spatial density of mass movements.

58 GEOSCIENCES↗

SNM Radiation Signature Classification Using Different Semi-Supervised Machine Learning Models

The timely detection of special nuclear material (SNM) transfers between nuclear facilities is an important monitoring objective in nuclear nonproliferation. Persistent monitoring enabled by successful detection and characterization of radiological material movements could greatly enhance the nuclear nonproliferation mission in a range of applications. Supervised machine learning can be used to signal detections when material is present if a model is trained on sufficient volumes of labeled measurements. However, the nuclear monitoring data needed to train robust machine learning models can be costly to label since radiation spectra may require strict scrutiny for characterization. Therefore, this work investigates the application of semi-supervised learning to utilize both labeled and unlabeled data. As a demonstration experiment, radiation measurements from sodium iodide (NaI) detectors are provided by the Multi-Informatics for Nuclear Operating Scenarios (MINOS) venture at Oak Ridge National Laboratory (ORNL) as sample data. Anomalous measurements are identified using a method of statistical hypothesis testing. After background estimation, an energy-dependent spectroscopic analysis is used to characterize an anomaly based on its radiation signatures. In the absence of ground-truth information, a labeling heuristic provides data necessary for training and testing machine learning models. Supervised logistic regression serves as a baseline to compare three semi-supervised machine learning models: co-training, label propagation, and a convolutional neural network (CNN). In each case, the semi-supervised models outperform logistic regression, suggesting that unlabeled data can be valuable when training and demonstrating value in semi-supervised nonproliferation implementations.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

Dust storms on Mars: Considerations and simulations

Aeolian processes are important in modifying the surface of Mars at present, and appear to have been significant in the geological past. Aeolian activity includes local and global dust storms, the formation of erosional features such as yardangs and depositional features such as sand dunes, and the erosion of rock and soil. As a means of understanding aeolian processes on Mars, an investigation is in progress that includes laboratory simulations, field studies of earth analogs, and interpretation of spacecraft data. This report describes the Martian Surface Wind Tunnel, an experimental facility established at NASA-Ames Research Center, and presents some results of the general investigation. Experiments dealing with wind speeds and other conditions required for the initiation of particle movement on Mars are described and considerations are given to the resulting effectiveness of aeolian erosion.

Greeley, R.↗

Short meridional scale anomalies in the lower stratosphere and upper troposphere

Consequences of the discovery of short-meridional scale anomalies (SMSAs) in the lower stratospheric temperature field in the analyses of Microwave Sounding Unit channel 4 data are examined. The time scales of these features, their presence in the u-wind, v-wind, and geopotential, and the heat and momentum fluxes resulting from the SMSAs are investigated. The SMSAs are not regularly propagating features. Latitudinal movement occurs in both northern and southern directions. Both eastward movement and stationarity are observed in the zonal direction. In episodes, SMSAs require a few days to grow, persist from a few days to two weeks, and then decay over a few days. Heat fluxes are small. It is suggested that the SMSAs are possibly caused by secondary effects of baroclinic disturbances.

Newman, P. A.↗

The gust-front detection and wind-shift algorithms for the Terminal Doppler Weather Radar system

The Federal Aviation Administration's (FAA) Terminal Doppler Weather Radar (TDWR) system was primarily designed to address the operational needs of pilots in the avoidance of low-altitude wind shears upon takeoff and landing at airports. One of the primary methods of wind-shear detection for the TDWR system is the gust-front detection algorithm. The algorithm is designed to detect gust fronts that produce a wind-shear hazard and/or sustained wind shifts. It serves the hazard warning function by providing an estimate of the wind-speed gain for aircraft penetrating the gust front. The gust-front detection and wind-shift algorithms together serve a planning function by providing forecasted gust-front locations and estimates of the horizontal wind vector behind the front, respectively. This information is used by air traffic managers to determine arrival and departure runway configurations and aircraft movements to minimize the impact of wind shifts on airport capacity. This paper describes the gust-front detection and wind-shift algorithms to be fielded in the initial TDWR systems. Results of a quantitative performance evaluation using Doppler radar data collected during TDWR operational demonstrations at the Denver, Kansas City, and Orlando airports are presented. The algorithms were found to be operationally useful by the FAA airport controllers and supervisors.

Hermes, Laurie G.↗

An Evaluation of the Frequency and Severity of Motion Sickness Incidences in Personnel Within the Command and Control Vehicle (C2V)

The purpose of this study was to assess the frequency and severity of motion sickness in personnel during a field exercise in the Command and Control Vehicle (C2V). This vehicle contains four workstations where military personnel are expected to perform command decisions in the field during combat conditions. Eight active duty military men (U.S. Army) at the Yuma Proving Grounds in Arizona participated in this study. All subjects were given baseline performance tests while their physiological responses were monitored on the first day. On the second day of their participation, subjects rode in the C2V while their physiological responses and performance measures were recorded. Self-reports of motion sickness were also recorded. Results showed that only one subject experienced two incidences of emesis. However, seven out of the eight subjects reported other motion sickness symptoms; most predominant was the report of drowsiness, which occurred a total of 19 times. Changes in physiological responses were observed relative to motion sickness symptoms reported and the different environmental conditions (i.e., level, hills, gravel) during the field exercise. Performance data showed an overall decrement during the C2V exercise. These findings suggest that malaise and severe drowsiness can potentially impact the operational efficiency of the C2V crew. It was concluded that conflicting sensory information from the subject's visual displays and movements of the vehicle during the field exercise significantly contributed to motion sickness symptoms. It was recommended that a second study be conducted to further evaluate the impact of seat position or orientation and C2V experience on motion sickness susceptibility. Further, it was recommended that an investigation be performed on behavioral methods for improving crew alertness, motivation, and performance and for reducing malaise.

Cowings, Patricia S.↗

Long-Term Arctic Peatland Dynamics, Vegetation and Climate History of the Pur-Taz Region, Western Siberia

Stratigraphic analyses of peat composition, LOI, pollen, spores, macrofossils, charcoal, and AMS ages are used to reconstruct the peatland, vegetation and climatic dynamics in the Pur-Taz region of western Siberia over 5000 years (9300 - 4500 BP). Section stratigraphy shows many changes from shallow lake sediment to different combinations of forested or open sedge, moss, and Equisetum fen and peatland environments. Macrofossil and pollen data indicate that Larix sibirica and Betula pubescens trees were first to arrive, followed by Picea obovata. The dominance of Picea macrofossils 6000-5000 BP in the Pur-Taz peatland along with regional Picea pollen maxima indicate warmer conditions and movement of the spruce treeline northward at this time. The decline of pollen and macrofossils from all of these tree species in uppermost peats suggests a change in the environment less favorable for their growth, perhaps cooler temperatures and/or less moisture. Of major significance is the evidence for old ages of the uppermost peats in this area of Siberia, suggesting a real lack of peat accumulation in recent millennia or recent oxidation of uppermost peat.

Peteet, Dorothy↗

Loads Model Development and Analysis for the F/A-18 Active Aeroelastic Wing Airplane

The Active Aeroelastic Wing airplane was successfully flight-tested in March 2005. During phase 1 of the two-phase program, an onboard excitation system provided independent control surface movements that were used to develop a loads model for the wing structure and wing control surfaces. The resulting loads model, which was used to develop the control laws for phase 2, is described. The loads model was developed from flight data through the use of a multiple linear regression technique. The loads model input consisted of aircraft states and control surface positions, in addition to nonlinear inputs that were calculated from flight-measured parameters. The loads model output for each wing consisted of wing-root bending moment and torque, wing-fold bending moment and torque, inboard and outboard leading-edge flap hinge moment, trailing-edge flap hinge moment, and aileron hinge moment. The development of the Active Aeroelastic Wing loads model is described, and the ability of the model to predict loads during phase 2 research maneuvers is demonstrated. Results show a good match to phase 2 flight data for all loads except inboard and outboard leading-edge flap hinge moments at certain flight conditions. The average load prediction errors for all loads at all flight conditions are 9.1 percent for maximum stick-deflection rolls, 4.4 percent for 5-g windup turns, and 7.7 percent for 4-g rolling pullouts.

Allen, Michael J.↗

Loads Model Development and Analysis for the F/A-18 Active Aeroelastic Wing Airplane

The Active Aeroelastic Wing airplane was successfully flight-tested in March 2005. During phase 1 of the two-phase program, an onboard excitation system provided independent control surface movements that were used to develop a loads model for the wing structure and wing control surfaces. The resulting loads model, which was used to develop the control laws for phase 2, is described. The loads model was developed from flight data through the use of a multiple linear regression technique. The loads model input consisted of aircraft states and control surface positions, in addition to nonlinear inputs that were calculated from flight-measured parameters. The loads model output for each wing consisted of wing-root bending moment and torque, wing-fold bending moment and torque, inboard and outboard leading-edge flap hinge moment, trailing-edge flap hinge moment, and aileron hinge moment. The development of the Active Aeroelastic Wing loads model is described, and the ability of the model to predict loads during phase 2 research maneuvers is demonstrated. Results show a good match to phase 2 flight data for all loads except inboard and outboard leading-edge flap hinge moments at certain flight conditions. The average load prediction errors for all loads at all flight conditions are 9.1 percent for maximum stick-deflection rolls, 4.4 percent for 5-g windup turns, and 7.7 percent for 4-g rolling pullouts.

Allen, Michael J.↗

Responding to Climate Change: Adelie Penguins Confront Astronomical and Ocean Boundaries

Long-distance migration enables many organisms to take advantage of lucrative breeding and feeding opportunities during summer at high latitudes and then to move to lower, more temperate latitudes for the remainder of the year. The latitudinal range of the Ad lie penguin spans ~ 22 deg. Penguins from northern colonies may not migrate, but due to the high latitude of Ross Island colonies, these penguins almost certainly undertake the longest migrations for the species. Previous work has suggested that Adelies require both pack ice and some ambient light at all times of year. Over a 3-yr period, which included winters of both extensive and reduced sea ice, we investigated migratory routes and characteristics and wintering locations of Adelie Penguins from two colonies of very different size on Ross Island, Ross Sea, the southernmost colonies for any penguin. We acquired data from 3-16 Geolocation Sensors affixed to penguins each year at both Cape Royds and Cape Crozier in 2003-2005. Migrations averaged 12,760 km, with the longest being 17,600 km, and were in part facilitated by pack ice movement. Trip distances varied annually, but not by colony. Penguins rarely traveled north of the main sea ice pack, and used areas with high sea-ice concentration, ranging from 75-85%, about 500 km inward from the ice edge. They also used locations where there was some twilight (2-7 hr with sun greater than 6 below horizon). We review how Adelie Penguin migration has likely changed since withdrawal of the West Antarctic Ice 35 Sheet across the Ross Sea beginning 12,000 yBP. If sea ice extent in the Ross Sea sector decreases, as predicted by climate models, we can expect change in wintering areas, the location of which ultimately may be limited more by the availability of adequate light for visual foraging than by the availability of suitable pack-ice.

Ballard, Grant↗

Semiautonomous Avionics-and-Sensors System for a UAV

Unmanned Aerial Vehicles (UAVs) autonomous or remotely controlled pilotless aircraft have been recently thrust into the spotlight for military applications, for homeland security, and as test beds for research. In addition to these functions, there are many space applications in which lightweight, inexpensive, small UAVS can be used e.g., to determine the chemical composition and other qualities of the atmospheres of remote planets. Moreover, on Earth, such UAVs can be used to obtain information about weather in various regions; in particular, they can be used to analyze wide-band acoustic signals to aid in determining the complex dynamics of movement of hurricanes. The Advanced Sensors and Electronics group at Langley Research Center has developed an inexpensive, small, integrated avionics-and-sensors system to be installed in a UAV that serves two purposes. The first purpose is to provide flight data to an AI (Artificial Intelligence) controller as part of an autonomous flight-control system. The second purpose is to store data from a subsystem of distributed MEMS (microelectromechanical systems) sensors. Examples of these MEMS sensors include humidity, temperature, and acoustic sensors, plus chemical sensors for detecting various vapors and other gases in the environment. The critical sensors used for flight control are a differential- pressure sensor that is part of an apparatus for determining airspeed, an absolute-pressure sensor for determining altitude, three orthogonal accelerometers for determining tilt and acceleration, and three orthogonal angular-rate detectors (gyroscopes). By using these eight sensors, it is possible to determine the orientation, height, speed, and rates of roll, pitch, and yaw of the UAV. This avionics-and-sensors system is shown in the figure. During the last few years, there has been rapid growth and advancement in the technological disciplines of MEMS, of onboard artificial-intelligence systems, and of smaller, faster, and smarter wireless telemetry systems. The major attraction of MEMS lies in orders-of-magnitude reductions of power requirements relative to traditional electronic components that perform equivalent functions. In addition, the compactness of MEMS, relative to functionally equivalent traditional electronics systems, makes MEMS attractive for UAV applications. Recent advances in MEMS have made it possible to produce pressure, acceleration, humidity, and temperature sensors having masses in subgram range and possessing sensitivities and accuracies comparable to those of larger devices.

Shams, Qamar↗

Multi-agent autonomous system

A multi-agent autonomous system for exploration of hazardous or inaccessible locations. The multi-agent autonomous system includes simple surface-based agents or craft controlled by an airborne tracking and command system. The airborne tracking and command system includes an instrument suite used to image an operational area and any craft deployed within the operational area. The image data is used to identify the craft, targets for exploration, and obstacles in the operational area. The tracking and command system determines paths for the surface-based craft using the identified targets and obstacles and commands the craft using simple movement commands to move through the operational area to the targets while avoiding the obstacles. Each craft includes its own instrument suite to collect information about the operational area that is transmitted back to the tracking and command system. The tracking and command system may be further coupled to a satellite system to provide additional image information about the operational area and provide operational and location commands to the tracking and command system.

Fink, Wolfgang↗

Physics‐based iterative reconstruction for dual‐source and flying focal spot computed tomography

Purpose For single‐source helical Computed Tomography (CT), both Filtered‐Back Projection (FBP) and statistical iterative reconstruction have been investigated. However, for dual‐source CT with flying focal spot (DS‐FFS CT), a statistical iterative reconstruction that accurately models the scanner geometry and acquisition physics remains unknown to researchers. Therefore, our purpose is to present a novel physics‐based iterative reconstruction method for DS‐FFS CT and assess its image quality. Methods Our algorithm uses precise physics models to reconstruct from the native cone‐beam geometry and interleaved dual‐source helical trajectory of a DS‐FFS CT. To do so, we construct a noise physics model to represent data acquisition noise and a prior image model to represent image noise and texture. In addition, we design forward system models to compute the locations of deflected focal spots, the dimension, and sensitivity of voxels and detector units, as well as the length of intersection between x‐rays and voxels. The forward system models further represent the coordinated movement between the dual sources by computing their x‐ray coverage gaps and overlaps at an arbitrary helical pitch. With the above models, we reconstruct images by an advanced Consensus Equilibrium (CE) numerical method to compute the maximum a posteriori estimate to a joint optimization problem that simultaneously fits all models. Results We compared our reconstruction with Siemens ADMIRE, which is the clinical standard hybrid iterative reconstruction (IR) method for DS‐FFS CT, in terms of spatial resolution, noise profile, and image artifacts through both phantoms and clinical scan datasets. Experiments show that our reconstruction has a higher spatial resolution, with a Task‐Based Modulation Transfer Function (MTF task ) consistently higher than the clinical standard hybrid IR. In addition, our reconstruction shows a reduced magnitude of image undersampling artifacts than the clinical standard. Conclusions By modeling a precise geometry and avoiding data rebinning or interpolation, our physics‐based reconstruction achieves a higher spatial resolution and fewer image artifacts with smaller magnitude than the clinical standard hybrid IR.

Wang, Xiao↗

The natural thermoluminescence of meteorites. V - Ordinary chondrites at the Allan Hills ice fields

Natural thermoluminescence (TL) data have been obtained for 167 ordinary chondrites from the ice fields in the vicinity of the Allan Hills in Victoria Land, Antarctica, in order to investigate their thermal and radiation history, pairing, terrestrial age, and concentration mechanisms. Natural TL values for meteorites from the Main ice field are fairly low, while the Farwestern field shows a spread with many values 30-80 krad, suggestive of less than 150-ka terrestrial ages. There appear to be trends in TL levels within individual ice fields which are suggestive of directions of ice movement at these sites during the period of meteorite concentration. These directions seem to be confirmed by the orientations of elongation preserved in meteorite pairing groups. The proportion of meteorites with very low natural TL levels at each field is comparable to that observed at the Lewis Cliff site and for modern non-Antarctic falls and is also similar to the fraction of small perihelia orbits calculated from fireball and fall observations. Induced TL data for meteorites from the Allan Hills confirm trends which show that a select group of H chondrites from the Antarctic experienced a different extraterrestrial thermal history to that of non-Antarctic H chondrites.

Benoit, Paul H.↗