SEARCH · Engineering Papers

Results for “continuous flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57

All sources NASA NTRS DOE OSTI

NASA NTRS1981

Passive components for high temperature operation

The development of resistors, capacitors, and interconnect metalizations utilizing a low pressure chemical vapor deposition (LPCVD) process is described. The LPCVD process allows the passive components to be fabricated at temperatures higher than their highest operating temperatures. The deposition of thin films by LPCVD is accomplished by reacting one or more gases on the surface of a heated substrate. The substrates to be coated are placed on a graphite susceptor and then loaded into the center of a quartz reaction tube. The RF power is applied to the coil on the outside of the reaction tube which in turn is coupled into the graphite susceptor causing it to heat. Pressures of several torr or less are typical, with carrier flow rates of 0.1 to 2.0 liters/min. Nitrogen, hydrogen, and helium are typical carrier gases. These are controlled with mass flow controllers and the pressure is continuously monitored with a capacitive manometer. Materials selection and device testing are also discussed.

Raymond, L. S.↗

NASA NTRS1989

On the role of ozone in the stability of Rossby normal modes

The role of ozone in the linear stability of Rossby normal modes is examined in a continuously stratified, extratropical baroclinic atmosphere. The flow is described by coupled equations for the quasi-geostraphic potential vorticity and ozone volume mixing ratio. A perturbation analysis is carried out under the assumption of weak diabatic heating, which is generated by Newtonian cooling and dynamics-ozone interaction. An expression for the propagation and growth characteristics is obtained analytically in terms of the vertically averaged wave activity, which depends explicitly on the wave spatial structure, photochemistry, and basic state distributions of wind, temperature, and ozone mixing ratio. Calculations show that stationary internal modes, whose amplitudes are largest in the stratosphre, are destabilized by dynamics-ozone interaction and Newtonian cooling, with e-folding times on the order of 20-40 days.

Nathan, Terrence R.↗

NASA NTRS1990

Performance of alumina-supported Pt catalysts in an electron-beam-sustained CO2 laser amplifier

The performance of an alumina-supported Pt catalyst system used to maintain the gas purity in an electron-beam-sustained (636) isotope CO2 laser amplifier has been tested. The system characteristics using the two-zone, parallel flow reactor were determined for both continuous- and end-of-day reactor operation using on-line mass spectrometric sampling. The laser amplifier was run with an energy loading of typically 110 J-l/atm and an electron-beam current of 4 mA/sq cm. With these conditions and a pulse repetition frequency of 10 Hz for up to 10,000 shots, increases on the order of 100 ppm O2 were observed with the purifier on and 150 ppm with it off. The 1/e time recovery time was found to be approximately 75 minutes.

Cunningham, D. L.↗

NASA NTRS1991

Simulation Of Flow In A Turbine Cascade

Report discusses application of lower-upper (LU) implicit numerical-integration scheme, together with interactive grid-generation method, to simulation of inviscid, compressible flow in two-dimensional model of turbine cascade. Study part of continuing effort to develop techniques for computation of complicated three-dimensional flows in turbomachinery.

Choo, Yung K.↗

NASA NTRS1991

Two-Phase Bidirectional Heat Exchanger

Heat exchanger transfers heat from one two-phase thermal loop to another. Condenses vapor in one loop while evaporating liquid in other. Transfers heat with very small drops in temperature and pressure, and efficiently joins heat pipes thermally without mixing of their working fluids. Several such heat exchangers used to build long, complex multiloop heat-control systems. Exchanger bidirectional: transfers heat in reverse, condensing on normally evaporating side, and vice versa. Can warm equipment it normally cools, without using auxiliary heater. In reverse transfer, wicks on evaporating side supply liquid continuously by capillary action; reverse-flow pump not needed. Design modified for other working fluids and larger heat-transfer rates.

Kroliczek, Edward↗

NASA NTRS1991

The turbomachine blading design using S2-S1 approach

The boundary conditions corresponding to the design problem when the blades being simulated by the bound vorticity distribution are presented. The 3D flow is analyzed by the two steps S2 - S1 approach. In the first step, the number of blades is supposed to be infinite, the vortex distribution is transformed into an axisymmetric one, so that the flow field can be analyzed in a meridional plane. The thickness distribution of the blade producing the flow channel striction is taken into account by the modification of metric tensor in the continuity equation. Using the meridional stream function to define the flow field, the mass conservation is satisfied automatically. The governing equation is deduced from the relation between the azimuthal component of the vorticity and the meridional velocity. The value of the azimuthal component of the vorticity is provided by the hub to shroud equilibrium condition. This step leads to the determination of the axisymmetric stream sheets as well as the approximate camber surface of the blade. In the second step, the finite number of blades is taken into account, the inverse problem corresponding to the blade to blade flow confined in each stream sheet is analyzed. The momentum equation implies that the free vortex of the absolute velocity must be tangential to the stream sheet. The governing equation for the blade to blade flow stream function is deduced from this condition. At the beginning, the upper and the lower surfaces of the blades are created from the camber surface obtained from the first step with the assigned thickness distribution. The bound vorticity distribution and the penetrating flux conservation applied on the presumed blade surface constitute the boundary conditions of the inverse problem. The detection of this flux leads to the rectification of the geometry of the blades.

Luu, T. S.↗

NASA NTRS1992

Viscous-shock-layer analysis of hypersonic flows over long slender vehicles

An efficient and accurate method for solving the viscous shock layer equations for hypersonic flows over long slender bodies is presented. The two first order equations, continuity and normal momentum, are solved simultaneously as a coupled set. The flow conditions included are from high Reynolds numbers at low altitudes to low Reynolds numbers at high altitudes. For high Reynolds number flows, both chemical nonequilibrium and perfect gas cases are analyzed with surface catalytic effects and different turbulence models, respectively. At low Reynolds number flow conditions, corrected slip models are implemented with perfect gas case. Detailed comparisons are included with other predictions and experimental data.

Lee, Kam-Pui↗

NASA NTRS1992

Structure of sunspot penumbrae - Fallen magnetic flux tubes

A model is presented of a sunspot penumbra involving magnetic flux tubes that have fallen into the photosphere and float there. An upwelling at the inner end of a fallen tube continuously provides additional gas. This gas flows along and lengthens the tube and is observable as the Evershed flow. Fallen flux tubes may appear as bright streaks near the upwelling, but they become dark filaments further out. The model is corroborated by recent optical high-resolution magnetic data regarding the penumbral filaments, by the 12-micron magnetic measurements relevant to the height of the temperature minimum, and by photographs of the umbra/penumbra boundary.

Wentzel, Donat G.↗

NASA NTRS1992

Diurnal HO2 cycles at clean air and urban sites in the troposphere

HO2 concentrations at two Oregon sites were determined for continuous periods of 36 to 48 hours, using fluorescence assay with gas expansion. At the sea level coastal site, NNW winds prevailed during daytime, and a point measurement of very low total nonmethane hydrocarbon concentration indicated the presence of remote tropospheric air of oceanic origin. At the urban site, HO2 was determined during moderately low ozone pollution levels. At both sites, maximum daily (HO2) was in the range of 1-2 x 10 exp 8/cu cm under clear-sky conditions, with an estimated overall uncertainty of 40 percent. HO2 was detected by continuous low-pressure sampling with flowing chemical conversion to HO, which was detected by laser-excited fluorescence. The instrumental response to HO2 was calibrated by the self-decay of HO2 at atmospheric pressure. Interference in the measured daytime HO2 concentrations by RO2 was estimated at less than 20 percent.

Hard, T. M.↗

NASA NTRS1992

Three dimensional particle simulation of high altitude rocket plumes

The interaction of two nozzles exhausting into vacuum generates a complex three-dimensional shock structure. The shock structure and resulting plume flowfield is characterized by the nozzle separation distance. For the appropriate range of penetration Knudsen numbers, the analysis of this shock structure can be suitably accomplished through a Monte Carlo simulation. This paper describes the application of a general three-dimensional Monte Carlo simulation on the Connection Machine CM-2 to the analysis of the plume self-interaction shock in the near field. Results are presented for two cases, corresponding to a small and a large nozzle separation distance. The results correctly reproduce the expected flow features and demonstrate the ability of this method to properly simulate the start of the plume self-interaction shock. This has significance not only for allowing analysis of the self-interacting plume in the near field, but also for allowing the subsequent simulation of the far field flow through the use of a continuation downstream exit boundary.

Dagum, Leonardo↗

NASA NTRS1992

Polycyclic aromatic hydrocarbon formation in carbon-rich stellar envelopes

A detailed chemical kinetic scheme is applied to stellar envelope profiles of gas density and temperature profiles in order to study the formation of PAH molecules in carbon-rich stellar outflows. Chemical concentration profiles are calculated for several envelope models by integrating the coupled continuity equations that include spherically expanding flows from an inner boundary at the shock formation radius. The influence of the 'inverse greenhouse' effect experienced by small PAHs is investigated and shown to increase the PAH yield by many orders of magnitude. It is shown that the route through propargyl radicals could be an important channel to produce benzene. PAH formation yields are found to be extremely sensitive to gas density and temperature and are much smaller than values inferred from the observed dust content of late-type carbon-rich stellar envelopes. It is therefore unlikely that aromatic molecules are generated in the stellar outflow itself.

Cherchneff, Isabelle↗

NASA NTRS1995

Reduced dimer production in solar-simulator-pumped continuous wave iodine lasers based on model simulations and scaling and pumping studies

A numerical rate equation model for a continuous wave iodine laser with longitudinally flowing gaseous lasant is validated by approximating two experiments that compare the perfluoroalkyl iodine lasants n-C3F7I and t-C4F9I. The salient feature of the simulations is that the production rate of the dimer (C4F9)2 is reduced by one order of magnitude relative to the dimer (C3F7)2. The model is then used to investigate the kinetic effects of this reduced dimer production, especially how it improves output power. Related parametric and scaling studies are also presented. When dimer production is reduced, more monomer radicals (t-C4F9) are available to combine with iodine ions, thus enhancing depletion of the laser lower level and reducing buildup of the principal quencher, molecular iodine. Fewer iodine molecules result in fewer downward transitions from quenching and more transitions from stimulated emission of lasing photons. Enhanced depletion of the lower level reduces the absorption of lasing photons. The combined result is more lasing photons and proportionally increased output power.

Costen, Robert C.↗

NASA NTRS1995

Large eddy simulations of compressible turbulent flows

An evaluation of existing models for Large Eddy Simulations (LES) of incompressible turbulent flows has been completed. LES is a computation in which the large, energy-carrying structures to momentum and energy transfer is computed exactly, and only the effect of the smallest scales of turbulence is modeled. That is, the large eddies are computed and the smaller eddies are modeled. The dynamics of the largest eddies are believed to account for most of sound generation and transport properties in a turbulent flow. LES analysis is based on an observation that pressure, velocity, temperature, and other variables are the sum of their large-scale and small-scale parts. For instance, u(i) (velocity) can be written as the sum of bar-u(i) and u(i)-prime, where bar-u(i) is the large-scale and u(i)-prime is the subgrid-scale (SGS). The governing equations for large eddies in compressible flows are obtained after filtering the continuity, momentum, and energy equations, and recasting in terms of Favre averages. The filtering operation maintains only large scales. The effects of the small-scales are present in the governing equations through the SGS stress tensor tau(ij) and SGS heat flux q(i). The mathematical formulation of the Favre-averaged equations of motion for LES is complete.

Porter-Locklear, Freda↗

NASA NTRS1995

Improvement of Subsonic Basic Research Tunnel Flow Quality as Applied to Wall Mounted Testing

A survey to determine the characteristics of a boundary layer that forms on the wall of the Subsonic Basic Research Tunnel has been performed. Early results showed significant differences in the velocity profiles as measured spanwise across the wall. An investigation of the flow in the upstream contraction revealed the presence of a separation bubble at the beginning of the contraction which caused much of the observed unsteadiness. Vortex generators were successfully applied to the contraction inlet to alleviate the separation. A final survey of the wall boundary layer revealed variations in the displacement and momentum thicknesses to be less than +/- 5% for all but the most upper portion of the wall. The flow quality was deemed adequate to continue the planned follow-on tests to help develop the semi-span test technique.

Howerton, Brian M.↗

NASA NTRS1997

Guide to AERO2S and WINGDES Computer Codes for Prediction and Minimization of Drag Due to Lift

The computer codes, AER02S and WINGDES, are now widely used for the analysis and design of airplane lifting surfaces under conditions that tend to induce flow separation. These codes have undergone continued development to provide additional capabilities since the introduction of the original versions over a decade ago. This code development has been reported in a variety of publications (NASA technical papers, NASA contractor reports, and society journals). Some modifications have not been publicized at all. Users of these codes have suggested the desirability of combining in a single document the descriptions of the code development, an outline of the features of each code, and suggestions for effective code usage. This report is intended to supply that need.

Carlson, Harry W.↗

NASA NTRS1960

Full-Scale Wind-Tunnel Tests of Blowing Boundary-Layer Control Applied to a Helicopter Rotor

A full-scale wind-tunnel test was conducted of two boundary-layer-control applications to a 44-foot diameter helicopter rotor. Blowing from a nozzle near the leading edge of the blades delayed retreating blade stall. Results also indicated that delay of retreating blade stall could be obtained by cyclic blowing with a lower flow rate than that required for continuous blowing. It was found that blowing applied through a nozzle at mid-chord had no effect on retreating blade stall.

McCloud, John L., III↗

NASA NTRS2001

Bi-Component Droplet Combustion in Reduced Gravity

This research deals with reduced-gravity combustion of bi-component droplets initially in the mm size range or larger. The primary objectives of the research are to study the effects of droplet internal flows, thermal and solutal Marangoni stresses, and species volatility differences on liquid species transport and overall combustion phenomena (e.g., gas-phase unsteadiness, burning rates, sooting, radiation, and extinction). The research program utilizes a reduced-gravity environment so that buoyancy effects are rendered negligible. Use of large droplets also facilitates visualization of droplet internal flows, which is important for this research. In the experiments, droplets composed of low- and high-volatility species are burned. The low-volatility components are initially present in small amounts. As combustion of a droplet proceeds, the liquid surface mass fraction of the low-volatility component will increase with time, resulting in a sudden and temporary decrease in droplet burning rates as the droplet rapidly heats to temperatures close to the boiling point of the low-volatility component. This decrease in burning rates causes a sudden and temporary contraction of the flame. The decrease in burning rates and the flame contraction can be observed experimentally. Measurements of burning rates as well as the onset time for flame contraction allow effective liquid-phase species diffusivities to be calculated, e.g., using asymptotic theory. It is planned that droplet internal flows will be visualized in future flight and ground-based experiments. In this way, effective liquid species diffusivities can be related to droplet internal flow characteristics. This program is a continuation of extensive ground based experimental and theoretical research on bi-component droplet combustion that has been ongoing for several years. The focal point of this program is a flight experiment (Bi-Component Droplet Combustion Experiment, BCDCE). This flight experiment is under development. However, supporting studies have been performed. Because of space limitations, only some of the research performed over the last two years (since the 5th Microgravity Combustion Workshop) is summarized here.

Shaw, B. D.↗

NASA NTRS2003

An Assessment of CFD Effectiveness for Vortex Flow Simulation to Meet Preliminary Design Needs

The low-speed flight and transonic maneuvering characteristics of combat air vehicles designed for efficient supersonic flight are significantly affected by the presence of free vortices. At moderate-to-high angles of attack, the flow invariably separates from the leading edges of the swept slender wings, as well as from the forebodies of the air vehicles, and rolls up to form free vortices. The design of military vehicles is heavily driven by the need to simultaneously improve performance and affordability.1 In order to meet this need, increasing emphasis is being placed on using Modeling & Simulation environments employing the Integrated Product & Process Development (IPPD) concept. The primary focus is on expeditiously providing design teams with high-fidelity data needed to make more informed decisions in the preliminary design stage. Extensive aerodynamic data are needed to support combat air vehicle design. Force and moment data are used to evaluate performance and handling qualities; surface pressures provide inputs for structural design; and flow-field data facilitate system integration. Continuing advances in computational fluid dynamics (CFD) provide an attractive means of generating the desired data in a manner that is responsive to the needs of the preliminary design efforts. The responsiveness is readily characterized as timely delivery of quality data at low cost.

Raj, P.↗