Results for “concentration potential” — Page 57

DOE OSTI2022

Laboratory and pilot-scale studies of membrane distillation for desalination of produced water from Permian Basin

Substantial quantities of produced water generated during the extraction of oil and gas from unconventional reservoirs present significant environmental concern and increase the operating cost for this industry. Membrane Distillation (MD) can serve as a potential solution for beneficial reuse of produced water by generating high-quality permeate and reducing the volume of produced water requiring disposal. This study investigated treatment of produced water from Permian Basin in both laboratory and pilot-scale studies. Laboratory tests revealed the potential to successfully recover 50% of produced water although some increase in permeate conductivity was observed due to the passage of ammonia from the feed side. Initial pilot-scale test with filtration of raw produced water as the only pre-treatment step led to precipitation of SrSO 4 , NaCl, and Fe in the system once the solubility limits for these salts were exceeded. However, chemical pretreatment that included pH adjustment, aeration, and barite precipitation, allowed successful steady-state operation of the AGMD pilot system for 5 days where the produced water was concentrated from 127 g/L to 255 g/L (~50% water recovery) while recovering high quality permeate. Overall, greater than 99.7 % salt rejection was achieved with the average permeate flux of 1.86 LMH. Finally, mass balance analysis suggested potential Ba and Ca precipitation in the system but there was no impact on AGMD performance and permeate quality during 5 days of continuous operation in the field.

42 ENGINEERING↗

DOE OSTI2020

Database of pharmacokinetic time-series data and parameters for 144 environmental chemicals

Time courses of compound concentrations in plasma are used in chemical safety analysis to evaluate the relationship between external administered doses and internal tissue exposures. This type of experimental data is rarely available for the thousands of non-pharmaceutical chemicals to which people may potentially be unknowingly exposed but is necessary to properly assess the risk of such exposures. In vitro assays and in silico models are often used to craft an understanding of a chemical’s pharmacokinetics; however, the certainty of the quantitative application of these estimates for chemical safety evaluations cannot be determined without in vivo data for external validation. To address this need, we present a public database of chemical time-series concentration data from 567 studies in humans or test animals for 144 environmentally-relevant chemicals and their metabolites (187 analytes total). All major administration routes are incorporated, with concentrations measured in blood/plasma, tissues, and excreta. We also include calculated pharmacokinetic parameters for some studies, and a bibliography of additional source documents to support future extraction of time-series. In addition to pharmacokinetic model calibration and validation, these data may be used for analyses of diferential chemical distribution across chemicals, species, doses, or routes, and for meta-analyses on pharmacokinetic studies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

Rare earth element potential in coal and coal ash in the U.S. Gulf Coast

United States heavy reliance on imports of critical minerals (CMs), including rare earth elements (REEs), underscores the importance of development of domestic sources. The study objective was to quantify CM and REE concentrations in coal and coal ash in the US Gulf Coast region. CM and REE concentrations were measured for 118 samples from outcrops and 14 mines in the Gulf Coast. Results show that total REE + Yttrium (REY) concentrations (dry coal basis) are comparable to those of the upper continental crust (UCC) with localized hot spots, such as the Texas Gibbons Creek mine (REY ≤ ~ 2860 ppm). When normalized to UCC REY concentration (169 ppm, dry coal basis), REY to UCC ratios for Gulf Coast coal samples range from 0.1 to 17 (median ratio 0.6). REE extractability from lignites is high (median: 63%–93%) using environmentally benign weak acid. In addition to raw coal, coal ash from power plants could also serve as an REE source with a median ratio of REY in ash relative to coal of 4; however, extractability from coal ash is generally much lower (≤ 5% using the same weak acid as in coal). The median basket price for extracted REY as oxides from coal, assuming 70% extractability, is $\$3.2$ per tonne of coal and $\$186$ billion based on 58 billion metric tonnes of dry coal in the Gulf Coast. REEs important for magnets (Pr + Nd + Tb + Dy) account for ~ 80% of the total value. The corresponding median basket price for extracted REY as oxides from coal ash, assuming ~ 30% extractability, is ~$\$4.4$ per tonne of ash and $\$1.2$ billion based on 258 million tonnes of ash. REE production from coal would likely require co-products, such as activated carbon or humic acids, to attain economic viability. Production of REEs from coal ash could offset remediation costs related to potential water contamination. This reconnaissance study shows the potential for REE production from coal and coal ash in the Gulf Coast; however, carbon coproducts and/or societal benefits would likely be required for socioeconomic viability.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2023

The exceptional form and function of the giant bacterium Ca. Epulopiscium viviparus revolves around its sodium motive force

Epulopiscium spp. are the largest known heterotrophic bacteria; a large cigar-shaped individual is a million times the volume of Escherichia coli. To better understand the metabolic potential and relationship of Epulopiscium sp. type B with its host Naso tonganus, we generated a high-quality draft genome from a population of cells taken from a single fish. We propose the name Candidatus Epulopiscium viviparus to describe populations of this best-characterized Epulopiscium species. Metabolic reconstruction reveals more than 5% of the genome codes for carbohydrate active enzymes, which likely degrade recalcitrant host-diet algal polysaccharides into substrates that may be fermented to acetate, the most abundant short-chain fatty acid in the intestinal tract. Moreover, transcriptome analyses and the concentration of sodium ions in the host intestinal tract suggest that the use of a sodium motive force (SMF) to drive ATP synthesis and flagellar rotation is integral to symbiont metabolism and cellular biology. In natural populations, genes encoding both F-type and V-type ATPases and SMF generation via oxaloacetate decarboxylation are among the most highly expressed, suggesting that ATPases synthesize ATP and balance ion concentrations across the cell membrane. High expression of these and other integral membrane proteins may allow for the growth of its extensive intracellular membrane system. Further, complementary metabolism between microbe and host is implied with the potential provision of nitrogen and B vitamins to reinforce this nutritional symbiosis. The few features shared by all bacterial behemoths include extreme polyploidy, polyphosphate synthesis, and thus far, they have all resisted cultivation in the lab.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2025

Data for Identifying the best high-biomass sorghum hybrids based on biomass yield potential and feedstock quality affected by nitrogen fertility management under various environments

Data were collected from agronomy fields in Urbana and Ewing, IL, during the 2022 and 2023 growing seasons. The dataset includes dry biomass yield, nitrogen, phosphorus, and potassium concentrations and removals, and chemical composition elements (cellulose, hemicellulose, lignin, and soluble fractions) for 13 high-biomass sorghum hybrids. data_sharing.xlsx contains 20 columns and 104 rows. Below is the explanation of all variables in the file: Year: 2022; 2023 Location: Urbana, IL; Ewing, IL N rate (kg-N/ha): 0; 112 Hybrid #: H1-H13 Pedigree: Pedigree for 13 hybrids Dry biomass yield (Mg/ha): Aboveground dry biomass yield N (g/kg): Nitrogen concentration in plant tissue P (g/kg): Phosphorus concentration in plant tissue K (g/kg): Potassium concentration in plant tissue N (kg/ha): Nitrogen removal by aboveground biomass P (kg/ha): Phosphorus removal by aboveground biomass K (kg/ha): Potassium removal by aboveground biomass Cellulose (g/kg): Cellulose concentration in plant tissue Hemicellulose (g/kg): Hemicellulose concentration in plant tissue Lignin (g/kg): Lignin concentration in plant tissue Soluble (g/kg): Soluble concentration in plant tissue Cellulose (Mg/ha): Cellulose content in aboveground biomass Hemicellulose (Mg/ha): Hemicellulose content in aboveground biomass Lignin (Mg/ha): Lignin content in aboveground biomass Soluble (Mg/ha): Soluble content in aboveground biomass

environmental adaptability↗

DOE OSTI2024

In Vitro Antimicrobial Activity of Volatile Compounds from the Lichen Pseudevernia furfuracea (L.) Zopf. Against Multidrug-Resistant Bacteria and Fish Pathogens

Lichens are symbiotic organisms with unique secondary metabolism. Various metabolites from lichens have shown antimicrobial activity. Nevertheless, very few studies have investigated the antimicrobial potential of the volatile compounds they produce. This study investigates the chemical composition and antimicrobial properties of volatile compounds from Pseudevernia furfuracea collected in two regions of Morocco. Hydrodistillation was used to obtain volatile compounds from samples collected in the High Atlas and Middle Atlas. Gas chromatography–mass spectrometry (GC-MS) analysis identified phenolic cyclic compounds as the primary constituents, with atraric acid and chloroatranol being the most abundant. Additionally, eight compounds were detected in lichens for the first time. The antimicrobial activity of these compounds was assessed using disc diffusion and broth microdilution methods. Both samples demonstrated significant antimicrobial effects against multidrug-resistant human bacteria, reference microorganisms, fish pathogens, and Candida albicans, with minimum inhibitory concentrations (MICs) ranging from 1000 µg/mL to 31.25 µg/mL. This study provides the first report on the volatile compounds from Pseudevernia furfuracea and their antimicrobial effects, particularly against fish pathogens, suggesting their potential as novel antimicrobial agents for human and veterinary use. Further research is warranted to explore these findings in more detail.

Essadki, Yasser (ORCID:0009000648460075)↗

DOE OSTI2026

Evaluation of coal-associated sediments, wastes, and AMD sludge in the Southern Appalachian Basin as feedstock materials for REE and Li recovery

Critical minerals (CM) such as rare earth elements (REE+) and Lithium (Li) are essential to technological innovation, energy transitions, global economic and defense security, necessitating the search for unconventional resources and efficient recovery methods to avert supply chain disruptions. Here, this study evaluates coal-associated sediments (underclay and roof rock) and wastes from the Pennsylvanian Pottsville Formation of the Southern Appalachian Basin (SAB) as potential feedstocks for CM recovery. A total of 34 samples (15 underclays, 12 roof rocks, 5 Acid Mine Drainage (AMD) sludges, and 2 coal mining wastes) were characterized using XRD, XRF, ICP-MS, and μ-XRF analytical methods. The REE+ and Li concentrations of these materials ranged from 46.8 to 334.4 ppm and from 11.1 to 519 ppm, respectively, with one underclay sample (Hendrix 3456) yielding the highest values for both. Bulk mineralogy for all samples was dominated by aluminosilicate clay phases, particularly illite and kaolinite. All samples exhibited REY def, rel% values >26% and C outl indices that ranged from 0.69 to 0.94, classifying their REE ore potential as Category II (Promising) as defined by Seredin and Dai (2012). Extractability tests (EPA method 3051 A) yielded low REE+ and Li recoveries, with maximum values of 3.3% and 3.6%, respectively, suggesting associations with resistant minerals like clay and phosphates. Elemental mapping indicates that REE+ is associated with phosphate, whereas statistical analysis suggests that REE+ are associated with aluminosilicates, suggesting heterogeneous associations or minimal phosphate contribution. Li also correlated positively with Al 2 O 3 , indicating an aluminosilicate host. This study highlights the potential of coal-associated sediments in the SAB.

Clay minerals↗

DOE OSTI2021

Effect of electrode rinse solutions on the electrodialysis of concentrated salts

The data presented indicate that modest attention to the chemistry of the electrode rinse solution can yield as much as 56% improvement in process efficiency. When operating electrodialysis (ED) with salt concentrations greater than 10,000 mg/l (as NaCl) the amperage can be relatively high even at low voltages. To maximize the overall rate of ion transport from diluate to concentrate, there is a need to minimize resistances in the electrode cells since these can represent as much as 30% of the total resistances in the entire process and in this particular ED unit, represented resistance roughly equivalent to that within the membrane stack. This work describes the performance of a 10-cell pair, 200 cm 2 (0.02 m 2 ) per membrane, pilot ED unit operated in batch mode at 5 V potential. The feedstock to the stack was varied from 0.5% to 6% NaCl. Results from Volt-amp profiles (2.0–15 V) were used as the rationale for choosing the preferred electrode rinse solution, 90 g/l (kg/m 3 ) disodium sulfate at pH 12.5. The recommended solution of 30 g/l (kg/m 3 ) disodium sulfate at neutral pH was tested against stronger solutions (60, 90, and 120 g/l (kg/m 3 ) disodium sulfate) at neutral pH and with 1 g/l (kg/m 3 ) sodium hydroxide added to yield solutions at pH 12.5. There were stark differences in the performance of the ED unit between the solutions at pH 7 and those at pH 12.5. The slopes of the Volt-amp profiles improved indicating less resistance to ion flow at pH 12.5. Most of the difference can be attributed to the greater conductivity of sodium hydroxide compared to disodium sulfate, where even a modest addition of 1 g/l (kg/m 3 ) sodium hydroxide increased the conductivity of the solution between 8 and 20% depending on the concentration of disodium sulfate. Most notably, the initiation voltage was 2.39 ± 0.08 V with solutions at pH 7 and 1.99 V ± 0.04 V when the rinse solutions were around pH 12.5, a difference of around 0.42 V. Since the full batch runs were performed at 5.0 V, this 0.42 V differential represented a loss of 8% in process efficiency. A series of tests showed a shift in initiation voltage occurred between pH 11.5 and 12.5. Nernst equations for water electrolysis are coupled with a simple flux model that estimates the concentration of hydroxide and hydronium ions at the electrode surfaces. This model indicates that the potential demanded by the electrodes is directly linked to the current. Furthermore, there is a steep drop in the potential demanded by the anode when there is sufficient hydroxide available to generate oxygen from hydroxide as opposed to generation from water. The voltage demand is minimal at pH 12.5 and reflective of the reference standard voltage (just over 1.23 V predicted at 0.1 amps). However, the flux model predicts that the voltage demanded by the electrodes at pH 7 is 1.61 V at 0.1 amps (the lowest amperage measurable with the power pack). In conclusion, comparing this result to the reference standard (E 0 = -1.23 V) yields a satisfactory explanation for the observed difference below reference standard of 0.42 V.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Decarbonization of Wastewater Treatment with Microalgae Processes.

Microalgae can contribute to the decarbonization of wastewater treatment by municipalities, industries and agriculture, by substituting sunlight for energy intensive conventional treatment processes, while capturing nutrients and carbon in the algal biomass. The carbon fixed into the algal biomass can be converted to renewable natural gas (RNG) using anaerobic digestion or into renewable diesel and sustainable aviation fuel (SAF) using hydrothermal liquefaction (HTL), with greatly reduce the carbon footprints compared to conventional fuels. Bioplastics, biofertilizers and other bioproducts from microalgae biomass also provide potential benefits in greenhouse gas (GHG) reduction and domestic supply chains. Microalgae technologies can counter eutrophication caused by harmful algal blooms by recovering nutrients, N and P, from wastewaters, and even from very low nutrient concentrations found in surface waters. CO2 is required in microalgae cultivation and wastewater treatment to support maximal rates of the photosynthesis, with the CO2 obtained from the wastes themselves, other local sources or even atmospheric CO2. Greenhouse gas mitigation with microalgae processes is based on life cycle assessments, comparing such green processes with current energy intensive wastewater treatment, and nutrient reduction technologies. Microalgae technologies are specifically relevant to smaller, often disadvantaged, communities, where currently about 5,000 algae wastewater treatment ponds are operated by public utilities with many more are operated by industries. However, many, if not most, of these pond facilities require urgent technology upgrades to achieve the potential and goals of low cost GHG mitigation and efficient nutrient recycling. MicroBio Engineering Inc. is developing and has demonstrated several technologies that combine innovative carbon mitigation and decarbonization technologies for a circular economy, with longer-term potential for large-scale biofuels and biofertilizer production.

09 BIOMASS FUELS↗

DOE OSTI2023

Decarbonization of Wastewater Treatment with Microalgae Processes.

Microalgae can contribute to the decarbonization of wastewater treatment by municipalities, industries and agriculture, by substituting sunlight for energy intensive conventional treatment processes, while capturing nutrients and carbon in the algal biomass. The carbon fixed into the algal biomass can be converted to renewable natural gas (RNG) using anaerobic digestion or into renewable diesel and sustainable aviation fuel (SAF) using hydrothermal liquefaction (HTL), with greatly reduce the carbon footprints compared to conventional fuels. Bioplastics, biofertilizers and other bioproducts from microalgae biomass also provide potential benefits in greenhouse gas (GHG) reduction and domestic supply chains. Microalgae technologies can counter eutrophication caused by harmful algal blooms by recovering nutrients, N and P, from wastewaters, and even from very low nutrient concentrations found in surface waters. CO2 is required in microalgae cultivation and wastewater treatment to support maximal rates of the photosynthesis, with the CO2 obtained from the wastes themselves, other local sources or even atmospheric CO2. Greenhouse gas mitigation with microalgae processes is based on life cycle assessments, comparing such green processes with current energy intensive wastewater treatment, and nutrient reduction technologies. Microalgae technologies are specifically relevant to smaller, often disadvantaged, communities, where currently about 5,000 algae wastewater treatment ponds are operated by public utilities with many more are operated by industries. However, many, if not most, of these pond facilities require urgent technology upgrades to achieve the potential and goals of low cost GHG mitigation and efficient nutrient recycling. MicroBio Engineering Inc. is developing and has demonstrated several technologies that combine innovative carbon mitigation and decarbonization technologies for a circular economy, with longer-term potential for large-scale biofuels and biofertilizer production.

09 BIOMASS FUELS↗

DOE OSTI2023

Decarbonization of Wastewater Treatment with Microalgae Processes.

Microalgae can contribute to the decarbonization of wastewater treatment by municipalities, industries and agriculture, by substituting sunlight for energy intensive conventional treatment processes, while capturing nutrients and carbon in the algal biomass. The carbon fixed into the algal biomass can be converted to renewable natural gas (RNG) using anaerobic digestion or into renewable diesel and sustainable aviation fuel (SAF) using hydrothermal liquefaction (HTL), with greatly reduce the carbon footprints compared to conventional fuels. Bioplastics, biofertilizers and other bioproducts from microalgae biomass also provide potential benefits in greenhouse gas (GHG) reduction and domestic supply chains. Microalgae technologies can counter eutrophication caused by harmful algal blooms by recovering nutrients, N and P, from wastewaters, and even from very low nutrient concentrations found in surface waters. CO2 is required in microalgae cultivation and wastewater treatment to support maximal rates of the photosynthesis, with the CO2 obtained from the wastes themselves, other local sources or even atmospheric CO2. Greenhouse gas mitigation with microalgae processes is based on life cycle assessments, comparing such green processes with current energy intensive wastewater treatment, and nutrient reduction technologies. Microalgae technologies are specifically relevant to smaller, often disadvantaged, communities, where currently about 5,000 algae wastewater treatment ponds are operated by public utilities with many more are operated by industries. However, many, if not most, of these pond facilities require urgent technology upgrades to achieve the potential and goals of low cost GHG mitigation and efficient nutrient recycling. MicroBio Engineering Inc. is developing and has demonstrated several technologies that combine innovative carbon mitigation and decarbonization technologies for a circular economy, with longer-term potential for large-scale biofuels and biofertilizer production.

09 BIOMASS FUELS↗

DOE OSTI2025

The Impact of Europium as a Fission Product Surrogate on Chromium Corrosion in Molten Chloride Salt

The rising interest in molten salts, both as thermal energy storage media and as high-temperature solvents for fissile materials in advanced nuclear reactors, has spurred significant growth in research on structural and functional salt-facing materials. Impurities, such as water, play a significant role in the degradation of materials in molten salt environments. Other impurities, such as fission products, are expected to accumulate in molten salts during normal reactor operation and can affect the properties of the salt and salt-facing materials. During normal reactor operation, rare-earth element species are expected to form as byproducts of fission reactions, potentially degrading or altering the performance of both structural and functional materials exposed to salts. Here, in this work, fission product surrogates, europium metal and EuCl 3 , were added to the KCl-MgCl 2 salt while exposing pure Cr specimens in the melt at 600 and 700 °C for 1000 h. Low reactivity was observed with the baseline salt, while both the Eu and EuCl 3 additions to the salt resulted in increased mass loss of Cr specimens. A capillary electrophoresis technique was developed to enable the detection of low parts-per-million (ppm) concentrations of europium (Eu) in chloride salt both before and after exposure of Cr metal. This technique provides a sensitive and reliable method for monitoring trace levels of Eu, which is critical for understanding the interactions and potential contamination effects in salt-facing materials during reactor operation. This quantification technique can be applied to other cationic and anionic contaminants in halide salts.

chloride salt↗

DOE OSTI2022

Anion Effects on the Interfacial Structure and Bulk Physical Properties in Choline-Based Hydrogen-Bonded Electrolytes

Electrolytes consisting of choline (Ch) salts with acetate (Ac) and oxalate (Ox) anions were studied in mixtures with ethylene glycol (EG), in comparison to chloride (Cl)- and bis(trifluorosulfonyl)imide (TFSI)-containing systems to understand the impact of anion size and charge density on the bulk electrolyte and interfacial properties. These represent hydrogen-bonded concentrated electrolytes where the Ch salts are the H-bond acceptors (HBAs) and EG is the H-bond donor (HBD) in 1:2 and 1:4 HBA:HBD ratios. Increased H-bonding in Ch 2 Ox with EG compacts the liquid compared to ChAc, consistent with the increased dissociation energies of the HBA:HBD clusters with Ox –2 calculated by density functional theory (DFT), thus leading to denser and more viscous liquids. Electrochemical impedance spectroscopy (EIS) and surface-enhanced Raman spectroscopy (SERS) were used to investigate interfacial charge density and the electrode surface species. Differential capacitance curves demonstrate weak dependence on potential except for ChAc:EG, where Ac – is found to adsorb on the Au surface, in particular at +0.055 V vs Ag quasi-reference while no specific adsorption was observed on glassy carbon (GC). In situ SERS measurement confirms the formation of a surface layer in the ChAc:EG systems resulting from a Au–acetate interaction. Despite the structural similarities, Ox –2 did not show specific binding or any dependence of capacitance on potential as a result of strongly solvating EG molecules via H-bonds. Furthermore, this study shows that the charge density of the HBAs impacts both bulk properties and the electrical double-layer formation in concentrated H-bonded electrolytes that is relevant to electrochemical kinetics and morphology in electrodeposition processes and energy storage applications.

25 ENERGY STORAGE↗

DOE OSTI2021

Process Engineering to Increase the Layered Phase Concentration in the Immediate Products of Flame Spray Pyrolysis

Flame-spray-pyrolysis (FSP) is a robust and scalable process to synthesize particles at the commodity-scale. FSP has been used to produce the precursor powders which were converted to the layered structure $(R\bar{3m} \text { phase})$ by a postannealing step in making nickel-rich cathode materials (NCMs). Theoretically, the high flame temperature (normally >1500 K) in FSP can provide adequate energy for the phase conversion from rock-salt to layered structures and potentially enables one-step synthesis. However, the high flame temperature is a critical issue to cause lithium loss and structural degradation, preventing the formation of the layered phase. Here, guided by the gaseous nucleation theory, we implemented several FSP processes with different solution recipes. The layered phase concentration in the as-burned products can be increased with the solution enthalpies. By adding a rapid quench step to suppress the lithium loss and phase degradation, the layered phase can be further increased. This work contributes new ideas to innovating process regarding the process efficiency and throughput of manufacturing cathode materials at a large scale.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Health and air pollutant emission impacts of net zero CO2 by 2050 scenarios from the energy modeling forum 37 study

Carbon dioxide and non-greenhouse gas air pollutants are emitted from many of the same sources. Decarbonization actions thus typically yield air pollutant emission reductions, resulting in significant air quality benefits. Although several studies have highlighted this connection, including in the context of net zero carbon emission targets, substantial uncertainty remains regarding how alternative technological pathways to this goal will affect the spatial distribution and magnitude of air pollutants. Comprehensive multi-model and multi-scenario analyzes are needed to explore the relative impacts of alternative pathways. Here, our study begins to address this gap by leveraging the results from the recent Energy Modeling Forum 37 inter-model comparison exercise on U.S. decarbonization pathways. Comparing the results of the six teams who submitted air pollutant emissions suggests that strategies that target net zero U.S. carbon emissions would yield significant reductions in many air pollutants, and that this finding is generally robust across pathways. However, some energy sources, such as biomass and fossil fuels with carbon capture, will emit air pollutants and can potentially influence the magnitude, spatial distribution, and even sign of localized air pollutant emission changes. In the second part of this analysis, a simplified air quality and health impacts screening model is used to evaluate the air quality impacts in 2035 of sectoral emission changes from the three models that provided sectoral detail. Relative to a reference scenario, a net zero pathway is estimated to reduce fine particulate matter concentrations across the contiguous U.S., with health benefits from reduced mortality ranging from $\$$65 billion to $\$$250 billion in 2035 alone (2023$\$$s). These benefits would be expected to grow over time as the net zero trajectory becomes more stringent. Both the magnitude of potential benefits and the substantial variation of the projections across models underscore the need for an EMF-like inter-model comparison exercise focused on air quality.

Air pollutants↗

DOE OSTI2024

Luminescent Materials for the Detection of Economically Critical Metals in Harsh Environments

Renewable energy technologies used for electric vehicles and wind turbines are heavily reliant upon metals, such as rare earth elements, cobalt, lithium, and nickel. Indeed, there are 50 minerals that are currently considered “economically critical” by the 2022 United States Geological Survey. With anticipated global adoption of renewable energy technologies, producing sufficient metals to meet this demand presents a significant challenge, particularly due to the current monopolistic market for many of these metals. The production of metals from unconventional sources, such as coal utilization byproducts, is one of many promising strategies to boost domestic supply. However, sensitive, rapid, and inexpensive characterization technologies are needed to minimize production costs associated with metals prospecting and processing. Photoluminescence-based sensing techniques are particularly intriguing due to their potential for low cost and portability, coupled with high sensitivity and selectivity. This presentation focuses on the development of high-performance sensing materials for a range of critical metals, including metal-organic frameworks capable of sensitizing detection of parts-per-billion concentrations of six different rare earth elements, nanoparticles that can detect down to 600 parts-per-billion levels of cobalt, and thin films that sense aluminum down to 120 parts-per-billion. These materials are highly selective, capable of withstanding low pH conditions, and provide a response within minutes. Importantly, each sensing material is integrated with a custom-built, fully portable fiber-optic spectrometer for potential field deployment, providing significant cost savings over commercial instruments, along with potential advantages such as material regeneration for use across multiple sensing cycles and solvent removal for enhanced emission signal. These results highlight the exciting potential of luminescence platforms as cost-effective alternatives for metals characterization.

Crawford, Scott↗

DOE OSTI2023

Integrated Process Testing of MSR Salt Spill Accidents

Part of the licensing process for new nuclear reactors requires vendors to assess the potential consequences of identified accident scenarios using accident progression modeling. The accident scenario that will likely be evaluated by all molten salt reactor (MSR) developers is a spill of radionuclide-bearing fuel salt onto the reactor containment floor (i.e., a salt spill accident). The development of accident progression models requires experimental data to inform which processes to incorporate, to enable the calculation of parameters to model these processes, and to validate the model predictions. The data should quantify the sensitivities of key processes (e.g., molten salt spreading, heat transfer, containment structure corrosion, radionuclide vaporization, and aerosol generation) towards the initial conditions of the spill, the ambient environment, and the features of the containment. In addition, results from integrated process tests that quantify coupled processes are required to validate systems-level models. This report documents results from integrated process tests conducted on simulated molten salt spill accidents. The generated experimental data simultaneously quantify the heat transfer behavior of the spilled salt, compositional changes to the bulk salt, and the release of surrogate fission products from the spilled salt as aerosol particles. All tests that were conducted used FLiNaK doped with surrogate fission products, and the variables that were evaluated included the initial salt temperature and the concentration of surrogate fission products present in the salt. The major accomplishments of this work include identifying surrogate fuel salt compositions that provide insight into the dispersal behavior of radionuclides of potential significance to the source term, employing previously developed methods and measurement techniques to simultaneously measure key processes, generating data on the coupled processes of molten salt heat transfer and surrogate fission product release as aerosol particles, demonstrating new test methods for real-time monitoring of the flow rate of the spill and aerosol size quantification in an argon atmosphere, and developing a mass transfer model for cesium and iodine release from molten FLiNaK to provide insight into aerosol formation by vapor condensation. The same methodology applied herein can be employed to study different salt compositions of interest to MSR developers, different environmental conditions, and other variables that are relevant to postulated accident scenarios. The insights gained from these integrated process tests conducted at a laboratory scale will be incorporated into future integral effects tests conducted at an engineering scale.

20 FOSSIL-FUELED POWER PLANTS↗

DOE OSTI2022

Implications of Underground Nuclear Explosion Cavity Evolution for Radioxenon Isotopic Composition

Abstract Isotopic ratios of radioxenons sampled in the atmosphere or subsurface can be used to verify the occurrence of an underground nuclear explosion (UNE). Differences in the half-lives of radioactive xenon precursors and their decay-chain networks produce different time-dependent concentration profiles of xenon isotopes allowing isotopic ratios to be used for tracking UNE histories including estimating the time of detonation. In this study, we explore the potential effects of post-detonation cavity processes: precipitation of iodine precursors, gas seepage, and prompt venting on radioxenon isotopic evolution which influences UNE histories. Simplified analytical models and closed-form solutions yielding a potentially idealized radioactive decay/ingrowth chain in a closed and well-mixed system typically have limited application by not including the partitioning of the radionuclide inventory between a gas phase and rock melt created by the detonation and by ignoring gas transport from the cavity to host rock or ground surface. In reality, either subsurface transport or prompt release that is principally responsible for gas signatures violates the closed-system (or batch-mode) assumption. A closed-form solution representing time-dependent source-term activities is extended by considering the cavity partitioning process, slow seepage, and/or prompt release of gases from the cavity and applied to realistic systems.

Sun, Yunwei (ORCID:0000000194801439)↗