Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “compression techniques”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Innovative operating modes and techniques for the spaceborne imaging radar-C instrument

The operation of the spaceborne imaging radar-C (SIR-C) is discussed. The SIR-C instrument has been designed to obtain simultaneous multifrequency and simultaneous multipolarization radar images from a low earth orbit. It is a multiparameter imaging radar which will be flown during at least two different seasons. The instrument has been designed to operate in innovative modes such as the squint alignment mode, the extended aperture mode, the scansar mode, and the interferometry mode. The instrument has been designed to demonstrate innovative engineering techniques such as beam nulling for echo tracking, pulse-repetition frquency hopping for Doppler centroid tracking, generating the frequency step chirp for radar parameter flexibility, block floating point quantizing for data rate compression, and elevation beamwidth broadening for increasing the swath illumination.

Huneycutt, Bryan L.↗
NASA NTRS1991

Thermal-structural panel buckling tests

A titanium-matrix-composite (TMC) hat-stiffened panel of 61 cm sq area and 3.175 cm thick was nondestructively tested to 649 C to examine its buckling characteristics. Compressive loads were applied to the panel in a 978.6 kN uniaxial load frame system. High-temperature testing was performed using quartz lamp heating. A single-strain-age force/stiffness buckling prediction technique was developed to predict panel buckling loads. For the monolithic panel, these test predictions correlated within 10 percent with a finite-element buckling analyses performed elsewhere. Comparisons between force/stiffness predictions and analyses for the TMC panel are in progress.

Thompson, Randolph C.↗
NASA NTRS1993

Spaceborne Imaging Radar-C instrument

The Spaceborne Imaging Radar-C is the next radar in the series of spaceborne radar experiments, which began with Seasat and continued with SIR-A and SIR-B. The SIR-C instrument has been designed to obtain simultaneous multifrequency and simultaneous multipolarization radar images from a low earth orbit. It is a multiparameter imaging radar that will be flown during at least two different seasons. The instrument operates in the squint alignment mode, the extended aperture mode, the scansar mode, and the interferometry mode. The instrument uses engineering techniques such as beam nulling for echo tracking, pulse repetition frequency hopping for Doppler centroid tracking, generating the frequency step chirp for radar parameter flexibility, block floating-point quantizing for data rate compression, and elevation beamwidth broadening for increasing the swath illumination.

Huneycutt, Bryan L.↗
NASA NTRS1995

Auto-adaptive finite element meshes

Accurate capturing of discontinuities within compressible flow computations is achieved by coupling a suitable solver with an automatic adaptive mesh algorithm for unstructured triangular meshes. The mesh adaptation procedures developed rely on non-hierarchical dynamical local refinement/derefinement techniques, which hence enable structural optimization as well as geometrical optimization. The methods described are applied for a number of the ICASE test cases are particularly interesting for unsteady flow simulations.

Richter, Roland↗
NASA NTRS1998

Information-Adaptive Image Encoding and Restoration

The multiscale retinex with color restoration (MSRCR) has shown itself to be a very versatile automatic image enhancement algorithm that simultaneously provides dynamic range compression, color constancy, and color rendition. A number of algorithms exist that provide one or more of these features, but not all. In this paper we compare the performance of the MSRCR with techniques that are widely used for image enhancement. Specifically, we compare the MSRCR with color adjustment methods such as gamma correction and gain/offset application, histogram modification techniques such as histogram equalization and manual histogram adjustment, and other more powerful techniques such as homomorphic filtering and 'burning and dodging'. The comparison is carried out by testing the suite of image enhancement methods on a set of diverse images. We find that though some of these techniques work well for some of these images, only the MSRCR performs universally well oil the test set.

Park, Stephen K.↗
NASA NTRS1999

Cryogenic Fuel Tank Draining Analysis Model

One of the technological challenges in designing advanced hypersonic aircraft and the next generation of spacecraft is developing reusable flight-weight cryogenic fuel tanks. As an aid in the design and analysis of these cryogenic tanks, a computational fluid dynamics (CFD) model has been developed specifically for the analysis of flow in a cryogenic fuel tank. This model employs the full set of Navier-Stokes equations, except that viscous dissipation is neglected in the energy equation. An explicit finite difference technique in two-dimensional generalized coordinates, approximated to second-order accuracy in both space and time is used. The stiffness resulting from the low Mach number is resolved by using artificial compressibility. The model simulates the transient, two-dimensional draining of a fuel tank cross section. To calculate the slosh wave dynamics the interface between the ullage gas and liquid fuel is modeled as a free surface. Then, experimental data for free convection inside a horizontal cylinder are compared with model results. Finally, cryogenic tank draining calculations are performed with three different wall heat fluxes to demonstrate the effect of wall heat flux on the internal tank flow field.

Greer, Donald↗
NASA NTRS1980

Viscous compressible flow about blunt bodies using a numerically generated orthogonal coordinate system

A numerical solution to the Navier-Stokes equations was obtained for blunt axisymmetric entry bodies of arbitrary shape in supersonic flow. These equations are solved on a finite difference mesh obtained from a simple numerical technique which generates orthogonal coordinates between arbitrary boundaries. The governing equations are solved in time dependent form using Stetter's improved stability three step predictor corrector method. For the present application, the metric coefficients were obtained numerically using fourth order accurate, finite difference relations and proved to be totally reliable for the highly stretched mesh used to resolve the thin viscous boundary layer. Solutions are obtained for a range of blunt body nose shapes including concavities.

Graves, R. A., Jr.↗
NASA NTRSDate not supplied

Anisotropic Goal-Based Mesh Adaptation Metric Clarification and Development

Adaptive unstructured mesh techniques have a limited, but growing impact on production analysis workflows to control discretization error for reliable simulation results. Multiple independent implementations of flow solvers, anisotropic metric construction methods, and anisotropic mesh adaptation mechanics have matured. Goal-based metrics target estimated error in output functions, such as lift and drag, through the guidance of an adjoint solution. A unification of goal-based anisotropic metrics is presented for steady viscous flows, which is an active area of research. These goal-based metrics drive robust and efficient anisotropic mesh adaptation for the calculation of output functions. The super-convergent functional output error behavior of stabilized finite-element methods is exploited without a formal proof, and evidence of super-convergence is shown in numerical experiments. Mesh adapted drag and lift outputs for two simple bodies in compressible viscous flow show convergence of error to less than a single drag count. Asymptotic behavior established for relatively coarse meshes shows the efficiency of this goal-based metric when compared to solution interpolation error control and expert-guided meshing. Anisotropic mesh adaptation techniques are applied to a transport aircraft in a high-lift configuration where variation between approaches decreases with mesh refinement, but asymptotic behavior is not observed with available resources.

goal-based↗
NASA NTRS1975

Numerical calculation of unsteady transonic potential flow over helicopter rotor blades

The small-disturbance potential equation appropriate to a helicopter in forward flight is derived. This equation is then solved for the flow over a nonlifting transonic rotor blade, using a completely implicit scheme that is an extension of the Murman-Cole mixed-difference technique. The flow in the tip region is most unsteady in the decelerating flow region, after the blade passes the psi = 90 deg azimuthal station. The unsteadiness appears to be caused by expansion and compression waves that move slowly upstream of the blade as the relative incident flow decelerates. The influence of aspect ratio, advance ratio, and Mach number on this process is discussed.

Caradonna, F. X.↗
NASA NTRS1979

Cometary particulate analyzer

A concept for determining the relative abundance of elements contained in cometary particulates was evaluated. The technique utilizes a short, high intensity burst of laser radiation to vaporize and ionize collected particulate material. Ions extracted from this laser produced plasma are analyzed in a time of flight mass spectrometer to yield an atomic mass spectrum representative of the relative abundance of elements in the particulates. Critical aspects of the development of this system are determining the ionization efficiencies for various atomic species and achieving adequate mass resolution. A technique called energy-time focus, which utilizes static electric fields to alter the length of the ion flight path in proportion to the ion initial energy, was used which results in a corresponding compression to the range of ion flight times which effectively improves the inherent resolution. Sufficient data were acquired to develop preliminary specifications for a flight experiment.

Friichtenicht, J. F.↗
NASA NTRS1983

An analytical investigation of NO sub x control techniques for methanol fueled spark ignition engines

A thermokinetic SI engine simulation was used to study the effects of simple nitrogen oxide control techniques on performance and emissions of a methanol fueled engine. As part of this simulation, a ring crevice storage model was formulated to predict UBF emissions. The study included spark retard, two methods of compression ratio increase and EGR. The study concludes that use of EGR in high turbulence, high compression engines will both maximize power and thermal efficiency while minimizing harmful exhaust pollutants.

Browning, L. H.↗
NASA NTRS1985

A FORTRAN computer code for calculating flows in multiple-blade-element cascades

A solution technique has been developed for solving the multiple-blade-element, surface-of-revolution, blade-to-blade flow problem in turbomachinery. The calculation solves approximate flow equations which include the effects of compressibility, radius change, blade-row rotation, and variable stream sheet thickness. An integral equation solution (i.e., panel method) is used to solve the equations. A description of the computer code and computer code input is given in this report.

Mcfarland, E. R.↗
NASA NTRS1987

Pressure-Localizing Inserts for Bagging Laminations

Devices compress composite laminates to conform to tight inside corners of molds. Proposed use of pressure-localizing insert allows composite laminates to be compacted into tight corners by conventional pressure or vacuum-bagging techniques. Because of manufacturing technique, larger selection of part shapes becomes amenable to lamination.

Schmaling, Dave↗
NASA NTRS1987

Algorithm development

The past decade has seen considerable activity in algorithm development for the Navier-Stokes equations. This has resulted in a wide variety of useful new techniques. Some examples for the numerical solution of the Navier-Stokes equations are presented, divided into two parts. One is devoted to the incompressible Navier-Stokes equations, and the other to the compressible form.

Barth, Timothy J.↗
NASA NTRS1987

Optimal cure cycle design of a resin-fiber composite laminate

A unified computed aided design method was studied for the cure cycle design that incorporates an optimal design technique with the analytical model of a composite cure process. The preliminary results of using this proposed method for optimal cure cycle design are reported and discussed. The cure process of interest is the compression molding of a polyester which is described by a diffusion reaction system. The finite element method is employed to convert the initial boundary value problem into a set of first order differential equations which are solved simultaneously by the DE program. The equations for thermal design sensitivities are derived by using the direct differentiation method and are solved by the DE program. A recursive quadratic programming algorithm with an active set strategy called a linearization method is used to optimally design the cure cycle, subjected to the given design performance requirements. The difficulty of casting the cure cycle design process into a proper mathematical form is recognized. Various optimal design problems are formulated to address theses aspects. The optimal solutions of these formulations are compared and discussed.

Hou, Jean W.↗
NASA NTRS1988

Second order accurate finite difference approximations for the transonic small disturbance equation and the full potential equation

New shock-capturing finite difference approximations for solving two scalar conservation law nonlinear partial differential equations describing inviscid, isentropic, compressible flows of aerodynamics at transonic speeds are presented. A global linear stability theorem is applied to these schemes in order to derive a necessary and sufficient condition for the finite element method. A technique is proposed to render the described approximations total variation-stable by applying the flux limiters to the nonlinear terms of the difference equation dimension by dimension. An entropy theorem applying to the approximations is proved, and an implicit, forward Euler-type time discretization of the approximation is presented. Results of some numerical experiments using the approximations are reported.

Mostrel, M. M.↗
NASA NTRS1989

High compression image and image sequence coding

The digital representation of an image requires a very large number of bits. This number is even larger for an image sequence. The goal of image coding is to reduce this number, as much as possible, and reconstruct a faithful duplicate of the original picture or image sequence. Early efforts in image coding, solely guided by information theory, led to a plethora of methods. The compression ratio reached a plateau around 10:1 a couple of years ago. Recent progress in the study of the brain mechanism of vision and scene analysis has opened new vistas in picture coding. Directional sensitivity of the neurones in the visual pathway combined with the separate processing of contours and textures has led to a new class of coding methods capable of achieving compression ratios as high as 100:1 for images and around 300:1 for image sequences. Recent progress on some of the main avenues of object-based methods is presented. These second generation techniques make use of contour-texture modeling, new results in neurophysiology and psychophysics and scene analysis.

Kunt, Murat↗
NASA NTRS1991

Low-density, high-strength intermetallic matrix composites by XD (trademark) synthesis

A feasibility study was conducted to evaluate the potential of particulate composites based on low-density, L1(sub 2) trialuminide matrices for high-temperature applications. The compounds evaluated included Al22Fe3Ti8 (as a multiphase matrix), Al67Ti25Cr8, and Al66Ti25Mn9. The reinforcement consisted of TiB2 particulates. The TiB2 composites were processed by ingot and powder metallurgy techniques. Microstructural characterization and mechanical testing were performed in the hot-pressed and hot-isostatic-pressed condition. The casting were sectioned and isothermally forged into pancakes. All the materials were tested in compression as a function of temperature, and at high temperatures as a function of strain rate. The test results are discussed.

Kumar, K. S.↗