Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “boundary effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57
All sourcesNASA NTRSDOE OSTI
NASA NTRS1950

The Effect of the Inlet Mach Number and Inlet-boundary-layer Thickness on the Performance of a 23 Degree Conical-diffuser-tail-pipe Combination

An investigation was conducted to determine the effect of the inlet Mach number and entrance-boundary-layer thickness on the performance of a 23 degree 21-inch conical-diffuser - tail-pipe combination with a 2:1 area ratio. The air flows used in this investigation covered an inlet Mach number range from 0.17 to 0.89 and corresponding Reynolds numbers of 1,700,000 to 7,070,000. Results are reported for two inlet-boundary-layer thicknesses. Over the entire range of flows, the mean value of the inlet displacement thickness is about 0.034 inch for the thinner inlet boundary layer and about 0.170 inch for the case of the thicker inlet boundary layer. The performance of the diffuser - tail-pipe combination is presented together with examples of longitudinal static-pressure distribution and the results of boundary-layer pressure surveys made at six points along the diffuser wall. The results indicated a progressive diminution of the static-pressure recovery and a steady increase in the total-pressure losses as the inlet Mach number was increased for both inlet-boundary-layer thicknesses. The ratio of actual static-pressure rise to that theoretically possible was much less and the total-pressure losses were greater for the case of the thicker inlet boundary layer throughout the speed range investigated. With the thinner inlet boundary layer, flow separation occurred at the diffuser exit at all inlet Mach numbers.Unseparated flow alternating with separated flow was observed near the inlet at the higher velocities. For the case of the thicker inlet boundary layer, the origin of the separated region occurred in the vicinity of the inlet-duct-diffuser junction section at all Mach numbers.

Persh, Jerome↗
NASA NTRS1953

Smoke Studies of Secondary Flows in Bends, Tandem Cascades, and High-turning Configurations

Flow-visualization studies, using smoke, were made of the secondary flows in rectangular bends, tandem cascades, and high-turning configurations. The roll-up of the wall boundary layer of a rectangular bend forms a passage vortex near the suction surface similar to that previously observed for cascades. The vortex so formed then shifts out into the main stream. Because of leading-edge effects, the boundary-layer flows in bends were found to be sufficiently different from the flows in blade rows to make direct application of bend results to blade rows inadvisable. Passage vortices are shown, in the tandem-cascade study, to resist turning with the main stream through which they pass and to disturb the flow in subsequent blade rows. This disturbance may explain in part the appreciable size of the losses sometimes attributed to secondary flows in turbomachines despite the fact that the energy involvement in vortex formation is slight. Tip-flow studies of high-turning blades with relative motion between blades and end wall indicated that if the relative sizes of the passage vortex forces, the tip clearance forces, and the blade-scraping effects are properly controlled, it may be possible to improve the blade-tip loading characteristics in turbomachine.

CASCADES↗
DOE OSTI2020

A quantitative study of stress fields ahead of a slip band blocked by a grain boundary in unalloyed magnesium

Stress localization ahead of a slip band blocked by a grain boundary is measured for three different grain boundaries in unalloyed Mg using high-resolution electron backscatter diffraction (HR-EBSD). The results are compared with a theoretical dislocation pile-up model, from which slip system resistance and micro-Hall–Petch coefficients for different grain boundary types are deduced. The results indicate that grain boundary character plays a crucial role in determining micro-Hall–Petch coefficients, which can be used to strengthen classical crystal plasticity constitutive models to make predictions linked to the effect of grain boundary strengthening.

42 ENGINEERING↗
NASA NTRS1973

Single-stage experimental evaluation of tandem-airfoil rotor stator blading for compressors. Part 6: Data and performance for stage D

An axial flow compressor stage, having single-airfoil blading, was designed for zero rotor prewhirl, constant rotor work across the span, and axial discharge flow. The stage was designed to produce a pressure ratio of 1.265 at a rotor tip velocity of 757 ft/sec. The rotor had an inlet hub/tip ratio of 0.8. The design procedure accounted for the rotor inlet boundary layer and included the effects of axial velocity ratio and secondary flow on blade row performance. The objectives of this experimental program were: (1) to obtain performance with uniform and distorted inlet flow for comparison with the performance of a stage consisting of tandem-airfoil blading designed for the same vector diagrams; and (2) to evaluate the effectiveness of accounting for the inlet boundary layer, axial velocity ratio, and secondary flows in the stage design. With uniform inlet flow, the rotor achieved a maximum adiabatic efficiency of 90.1% at design equivalent rotor speed and a pressure ratio of 1.281. The stage maximum adiabatic efficiency at design equivalent rotor speed with uniform inlet flow was 86.1% at a pressure ratio of 1.266. Hub radial, tip radial, and circumferential distortion of the inlet flow caused reductions in surge pressure ratio of approximately 2, 10 and 5%, respectively, at design rotor speed.

Clemmons, D. R.↗
NASA NTRS1974

Single-stage experimental evaluation of tandem-airfoil rotor and stator blading for compressors. Part 7: Data and performance for stage E

An axial flow compressor stage, having tandem airfoil blading, was designed for zero rotor prewhirl, constant rotor work across the span, and axial discharge flow. The stage was designed to produce a pressure ratio of 1.265 at a rotor tip velocity of 757 ft/sec. The rotor has an inlet hub/tip ratio of 0.8. The design procedure accounted for the rotor inlet boundary layer and included the effects of axial velocity ratio and secondary flow on blade row performance. The objectives of this experimental program were (1) to obtain performance with uniform and distorted inlet flow for comparison with the performance of a stage consisting of single-airfoil blading designed for the same vector diagrams and (2) to evaluate the effectiveness of accounting for the inlet boundary layer, axial velocity ratio, and secondary flows in the stage design.

Cheatham, J. G.↗
NASA NTRS1977

Three-dimensional low Reynolds number flows with a free surface

The two-dimensional leveling problem (Degani, Gutfinger, 1976) is extended to three dimensions in the case where the flow Re number is very low and attention is paid to the free surface boundary condition with surface tension effects included. The no-slip boundary condition on the wall is observed. The numerical solution falls back on the Marker and Cell (MAC) method (Harlow and Welch, 1965) with the computation region divided into a finite number of stationary rectangular cells (or boxes in the 3-D case) and fluid flow traverses the cells (or boxes).

Degani, D.↗
NASA NTRS1980

Three dimensional mean flow and turbulence characteristics of the near wake of a compressor rotor blade

The investigation was carried out using the rotating hot wire technique. Measurements were taken inside the end wall boundary layer to discern the effect of annulus and hub wall boundary layer, secondary flow, and tip leakage on the wake structure. Static pressure gradients across the wake were measured using a static stagnation pressure probe insensitive to flow direction changes. The axial and the tangential velocity defects, the radial component of velocity, and turbulence intensities were found to be very large as compared to the near and far wake regions. The radial velocities in the trailing edge region exhibited characteristics prevalent in a trailing vortex system. Flow near the blade tips found to be highly complex due to interaction of the end wall boundary layers, secondary flows, and tip leakage flow with the wake. The streamwise curvature was found to be appreciable near the blade trailing edge. Flow properties in the trailing edge region are quite different compared to that in the near and far wake regions with respect to their decay characteristics, similarity, etc. Fourier decomposition of the rotor wake revealed that for a normalized wake only the first three coefficients are dominant.

Ravindranath, A.↗
DOE OSTI2022

Pressure-induced shift of effective Ce valence, Fermi energy and phase boundaries in CeOs 4 Sb 12

Abstract CeOs 4 Sb 12 , a member of the skutterudite family, has an unusual semimetallic low-temperature L -phase that inhabits a wedge-like area of the field H —temperature T phase diagram. We have conducted measurements of electrical transport and megahertz conductivity on CeOs 4 Sb 12 single crystals under pressures of up to 3 GPa and in high magnetic fields of up to 41 T to investigate the influence of pressure on the different H – T phase boundaries. While the high-temperature valence transition between the metallic H -phase and the L -phase is shifted to higher T by pressures of the order of 1 GPa, we observed only a marginal suppression of the S -phase that is found below 1 K for pressures of up to 1.91 GPa. High-field quantum oscillations have been observed for pressures up to 3.0 GPa and the Fermi surface of the high-field side of the H -phase is found to show a surprising decrease in size with increasing pressure, implying a change in electronic structure rather than a mere contraction of lattice parameters. We evaluate the field-dependence of the effective masses for different pressures and also reflect on the sample dependence of some of the properties of CeOs 4 Sb 12 which appears to be limited to the low-field region.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS2004

Stress Distribution During Deformation of Polycrystalline Aluminum by Molecular-Dynamics and Finite-Element Modeling

In this paper, a multiscale modelling strategy is used to study the effect of grain-boundary sliding on stress localization in a polycrystalline microstructure with an uneven distribution of grain size. The development of the molecular dynamics (MD) analysis used to interrogate idealized grain microstructures with various types of grain boundaries and the multiscale modelling strategies for modelling large systems of grains is discussed. Both molecular-dynamics and finite-element (FE) simulations for idealized polycrystalline models of identical geometry are presented with the purpose of demonstrating the effectiveness of the adapted finite-element method using cohesive zone models to reproduce grain-boundary sliding and its effect on the stress distribution in a polycrystalline metal. The yield properties of the grain-boundary interface, used in the FE simulations, are extracted from a MD simulation on a bicrystal. The models allow for the study of the load transfer between adjacent grains of very different size through grain-boundary sliding during deformation. A large-scale FE simulation of 100 grains of a typical microstructure is then presented to reveal that the stress distribution due to grain-boundary sliding during uniform tensile strain can lead to stress localization of two to three times the background stress, thus suggesting a significant effect on the failure properties of the metal.

Yamakov, V.↗
NASA NTRS1972

The effect of angle of attack on boundary-layer transition on cones.

Boundary-layer transition on 5- and 15-deg half-angle cones was studied as a function of angle of attack (ranging from 0 to 20 deg) in a 3.5 ft hypersonic wind tunnel at a freestream Mach number of 7.4. It is shown that the influence of the angle of attack on the transition Reynolds number is a function of the meridian angle. On the windward ray of the 15-deg cone, transition Reynolds numbers show an initial slight increase and then a decrease with increasing angle of attack; leeward-ray Reynolds numbers for this cone decrease rapidly with angle of attack. Windward-ray transition Reynolds numbers increase monotonically with angle of attack on the 5-deg cone, but the effect of the angle of attack on the leeward ray is the same as for the 15-deg cone.

Mateer, G. G.↗
NASA NTRS1984

Effect of curvature on three-dimensional boundary layer stability

The problem of the stability of a three-dimensional laminar boundary layer formed on a curved surface is considered. A calculation scheme, which takes account of the curvature of the flow streamlines and of the surface is proposed for the prediction of the development of small amplitude temporal disturbances. Computations have been performed for the flow over the windward face of an infinitely long yawed cylinder and comparisons have been made with experimental data. These indicate that the theory correctly predicts many of the features of the unstable laminar flow. The theory also suggests that transition, in this particular situation, is dominated by traveling disturbance waves and that, at the experimentally observed transition location, the wave which has undergone greatest total amplification has an amplitude ratio of approximately e to the 11th. When the effects of curvature are omitted the maximum amplitude ratio at transition is about e to the 17th.

Malik, M. R.↗
NASA NTRS1991

Effect of leading-edge geometry on boundary-layer receptivity to freestream sound

The receptivity to freestream sound of the laminar boundary layer over a semi-infinite flat plate with an elliptic leading edge is simulated numerically. The incompressible flow past the flat plate is computed by solving the full Navier-Stokes equations in general curvilinear coordinates. A finite-difference method which is second-order accurate in space and time is used. Spatial and temporal developments of the Tollmien-Schlichting wave in the boundary layer, due to small-amplitude time-harmonic oscillations of the freestream velocity that closely simulate a sound wave travelling parallel to the plate, are observed. The effect of leading-edge curvature is studied by varying the aspect ratio of the ellipse. The boundary layer over the flat plate with a sharper leading edge is found to be less receptive. The relative contribution of the discontinuity in curvature at the ellipse-flat-plate juncture to receptivity is investigated by smoothing the juncture with a polynomial. Continuous curvature leads to less receptivity. A new geometry of the leading edge, a modified super ellipse, which provides continuous curvature at the juncture with the flat plate, is used to study the effect of continuous curvature and inherent pressure gradient on receptivity.

Lin, Nay↗
NASA NTRS1958

A Low-Speed Experimental Investigation of the Effect of a Sandpaper Type of Roughness on Boundary-Layer Transition

An investigation was made in the Langley low-turbulence pressure tunnel to determine the effect of size and location of a sandpaper type of roughness on the Reynolds number for transition. Transition was observed by means of a hot-wire anemometer located at various chordwise stations for each position of the roughness. These observations indicated that when the roughness is sufficiently submerged in the boundary layer to provide a substantially linear variation of boundary-layer velocity with distance from the surface up to the top of the roughness, turbulent "spots" begin to appear immediately behind the roughness when the Reynolds number based on the velocity at the top of the roughness height exceeds a value of approximately 600. At Reynolds numbers even slightly below the critical value (value for transition), the sandpaper type of roughness introduced no measurable disturbances into the laminar layer downstream of the roughness. The extent of the roughness area does not appear to have an important effect on the critical value of the roughness Reynolds number.

Von Doenhoff, Albert E↗
DOE OSTI2021

Urbanization-induced land and aerosol impacts on storm propagation and hail characteristics

Changes in land surface and aerosol characteristics from urbanization can affect dynamic and microphysical properties of severe storms, thus affecting hazardous weather events resulting from such storms such as hail and tornado. We examine the joint and individual effects of urban land and anthropogenic aerosols of Kansas City on a severe convective storm observed during the 2015 Plains Elevated Convection At Night (PECAN) field campaign, focusing on storm evolution, convective intensity, and hail characteristics. The simulations are carried out at the cloud-resolving scale (1 km) using a version of WRF-Chem in which the spectral-bin microphysics (SBM) is coupled with the Model for Simulating Aerosol Interactions and Chemistry (MOSAIC). It is found that the urban land effect of Kansas City initiated a much stronger convective cell and the storm got further intensified when interacting with stronger turbulence induced by the urban land. The urban land effect also changed the storm path by diverting the storm toward the city mainly resulting from enhanced urban land-induced convergence in the urban area and around the urban-rural boundaries. The joint effect of urban land and anthropogenic aerosols enhances occurrences of both severe hail and significant severe hail by ~ 20% by enhancing hail formation and growth from riming. Overall the urban land effect on convective intensity and hail is relatively larger than the anthropogenic aerosol effect, but the joint effect is much notable than either of the individual effects, emphasizing the importance to consider both effects in evaluating urbanization effects.

Lin, Yun↗
DOE OSTI2024

Tokamak Disruption Simulation (Final Technical Report)

This was a multi-institutional project concerned with simulation of tokamak disruption – rapid termination of the plasma and confining magnetic field in a tokamak fusion reactor – with the aim of quantifying the physics associated with disruption mitigation. The PI’s role is as one of a group of computational scientists concerned with development of effective solution algorithms for the underlying models of magnetohydrodynamics and transport that represent the physical processes, and to develop techniques of uncertainty quantification for treating unknown aspects of the model such as boundary conditions and effects of impurities in plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1965

A Parametric Study of the Aerodynamic Characteristics of Nose-Cylinder-Flare Bodies at a Mach Number of 6.0

Force tests were conducted at a Mach number of 6.0 on nose-cylinder-flare bodies to determine the effect of nose shape, cylinder length, flare angle, and flare length on the longitudinal aerodynamic characteristics. A particular investigation was conducted to determine the effect of flare angle for constant flare length, surface area, and diameter. Results indicated that at a Reynolds number of approximately 0.92 x l0 (exp 6) (based on body diameter), the boundary-layer separation effects were significant only with respect to the slope of the normal-force and pitching-moment curve at low angles of attack. The variations of the aerodynamic characteristics with the various parameters were, in general, similar to those predicted by Newtonian theory below a flare angle of 30 degrees and a ratio of flare base diameter to cylinder diameter of less than approximately 2.2. The limiting diameter ratio is consistent with the extent of the low-constant dynamic-pressure region near the body caused by the bow-shock influences as predicted by axisymmetric characteristic theory. The effects of the various parameters for the flares that exceeded the limiting diameter ratio follow the trends predicted by the computed flow-field properties. The axial force for these flare configurations at zero angle of attack was, in general, computed within 10 percent by using these properties. For a constant flare length and surface area the flare effectiveness increased with increasing flare angle; however, for constant flare diameter only the axial-force coefficient was affected by flare angle.

Ashby, George C., Jr.↗
NASA NTRS1977

Effects of roughness size on the position of boundary-layer transition and on the aerodynamic characteristics of a 55 deg. swept delta wing at supersonic speeds

An experimental investigation was conducted to determine the effects of roughness size on the position of boundary layer transition and on the aerodynamic characteristics of a 55 deg swept delta wing model. Results are presented and discussed for wind tunnel tests conducted at free stream Mach numbers from 1.50 to 4.63, Reynolds numbers per meter from 3,300,000 to 1.6 x 10 to the 7th power, angles of attack from -8 to 16 deg, and roughness sizes ranging from 0.027 cm sand grit to 0.127 cm high cylinders. Comparisons were made with existing flat plate data. An approximate method was derived for predicting the drag of roughness elements used in boundary layer trips.

Stallings, R. L., Jr.↗