SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Practical tools which can extend the state of the art of moving base flight simulation for research and training are developed. Main approaches to this research effort include: (1) application of the vestibular model for perception of orientation based on motion cues: optimum simulator motion controls; and (2) visual cues in landing.
A 0.0196-scale model of the HL-20 lifting-body, one of several configurations proposed for future crewed spacecraft, was tested in the Langley 31-Inch Mach 10 Tunnel. The purpose of the tests was to determine the effectiveness of fin-mounted elevons, a lower surface flush-mounted body flap, and a flush-mounted yaw controller at hypersonic speeds. The nominal angle-of-attack range, representative of hypersonic entry, was 2 deg to 41 deg, the sideslip angles were 0 deg, 2 deg, and -2 deg, and the test Reynolds number was 1.06 x 10 E6 based on model reference length. The aerodynamic, longitudinal, and lateral control effectiveness along with surface oil flow visualizations are presented and discussed. The configuration was longitudinally and laterally stable at the nominal center of gravity. The primary longitudinal control, the fin-mounted elevons, could not trim the model to the desired entry angle of attack of 30 deg. The lower surface body flaps were effective for roll control and the associated adverse yawing moment was eliminated by skewing the body flap hinge lines. A yaw controller, flush-mounted on the lower surface, was also effective, and the associated small rolling moment was favorable.
The author has formulated a new, general model for specifying the kinematic properties of serial manipulators. The new model kinematic parameters do not suffer discontinuities when nominally parallel adjacent axes deviate from exact parallelism. From this new theory the author develops a first-order, lumped-parameter, calibration-model for the ARID manipulator. Next, the author develops a calibration methodology for the ARID based on visual and acoustic sensing. A sensor platform, consisting of a camera and four sonars attached to the ARID end frame, performs calibration measurements. A calibration measurement consists of processing one visual frame of an accurately placed calibration image and recording four acoustic range measurements. A minimum of two measurement protocols determine the kinematics calibration-model of the ARID for a particular region: assuming the joint displacements are accurately measured, the calibration surface is planar, and the kinematic parameters do not vary rapidly in the region. No theoretical or practical limitations appear to contra-indicate the feasibility of the calibration method developed here.
The Biocomputation Center at NASA Ames Research Center is dedicated to a union between computational, experimental and theoretical approaches to the study of neuroscience and of life sciences in general. The current emphasis is on computer reconstruction and visualization of vestibular macular architecture in three-dimensions (3-D), and on mathematical modeling and computer simulation of neural activity in the functioning system. Our methods are being used to interpret the influence of spaceflight on mammalian vestibular maculas in a model system, that of the adult Sprague-Dawley rat. More than twenty 3-D reconstructions of type I and type II hair cells and their afferents have been completed by digitization of contours traced from serial sections photographed in a transmission electron microscope. This labor-intensive method has now been replace d by a semiautomated method developed in the Biocomputation Center in which conventional photography is eliminated. All viewing, storage and manipulation of original data is done using Silicon Graphics workstations. Recent improvements to the software include a new mesh generation method for connecting contours. This method will permit the investigator to describe any surface, regardless of complexity, including highly branched structures such as are routinely found in neurons. This same mesh can be used for 3-D, finite volume simulation of synapse activation and voltage spread on neuronal surfaces visualized via the reconstruction process. These simulations help the investigator interpret the relationship between neuroarchitecture and physiology, and are of assistance in determining which experiments will best test theoretical interpretations. Data are also used to develop abstract, 3-D models that dynamically display neuronal activity ongoing in the system. Finally, the same data can be used to visualize the neural tissue in a virtual environment. Our exhibit will depict capabilities of our computational approaches and some of our findings from their application. For example, our research has demonstrated that maculas of adult mammals retain the property of synaptic plasticity. Ribbon synapses increase numerically and undergo changes in type and distribution (p<0.0001) in type II hair cells after exposure to microgravity for as few as nine days. The finding of macular synaptic plasticity is pertinent to the clinic, and may help explain some. balance disorders in humans. The software used in our investigations will be demonstrated for those interested in applying it in their own research.
Voice-actuated system allows one operator to do work of three. System uses voice-recognition-and-response unit and graphics terminal to interact with technician and to provide technician visual feedback. Computer-based Leakcheck system allows computer to do more of total work in checking model for leaks to reduce time and manpower required to perform task.
In this paper, we have introduced a comprehensive method for enterprise modeling that addresses the three important aspects of how an organization goes about its business. FirstEP includes infrastructure modeling, information modeling, and process modeling notations that are intended to be easy to learn and use. The notations stress the use of straightforward visual languages that are intuitive, syntactically simple, and semantically rich. ProSLCSE will be developed with automated tools and services to facilitate enterprise modeling and process enactment. In the spirit of FirstEP, ProSLCSE tools will also be seductively easy to use. Achieving fully managed, optimized software development and support processes will be long and arduous for most software organizations, and many serious problems will have to be solved along the way. ProSLCSE will provide the ability to document, communicate, and modify existing processes, which is the necessary first step.
Under a Phase II SBIR contract, Kennedy and Lumina Decision Systems, Inc., jointly developed the Schedule and Cost Risk Analysis Modeling (SCRAM) system, based on a version of Lumina's flagship software product, Analytica(R). Acclaimed as "the best single decision-analysis program yet produced" by MacWorld magazine, Analytica is a "visual" tool used in decision-making environments worldwide to build, revise, and present business models, minus the time-consuming difficulty commonly associated with spreadsheets. With Analytica as their platform, Kennedy and Lumina created the SCRAM system in response to NASA's need to identify the importance of major delays in Shuttle ground processing, a critical function in project management and process improvement. As part of the SCRAM development project, Lumina designed a version of Analytica called the Analytica Design Engine (ADE) that can be easily incorporated into larger software systems. ADE was commercialized and utilized in many other developments, including web-based decision support.
With the advent of multispacecraft missions, it became obvious that theoretical models are needed, not only to interpret local spacecraft observations, but also to link single point measurements. Models that address space plasma phenomena on local and global scales, that involve nonlinear processes, and that use self-consistent approaches, were developed. An interactive system for visualizing and analyzing numerical simulation results was also developed. This system is based on visualization modules which use the application visualization system and the NCAR graphic packages. Examples from recent simulations illustrate how these modules can be used for displaying and manipulating simulation results.
Application of gas-liquid two-phase flow systems for space-based thermal management and for the HEDS program demands a precise control of bubble size distribution in liquid. The necessity of bulk liquid motion for controlling bubble size and frequency in the space environment has been suggested by recent studies on pool, forced convection boiling and bubble formation in flowing liquid. The present work, consisting of two parts, explores bubble generation at wall in a cross-flowing liquid, i.e., in a forced convection boiling configuration. A schematic is shown. The first part looks into the bubble formation process under isothermal conditions in a reduced gravity environment, by injecting gas through a hole in the wall of a flowing liquid channel. In the latter part with channel wall heating, flow and temperature fields near a single bubble are studied under normal (1-g) and micro-gravity (mu-g) conditions. The objective of the isothermal experiments is to experimentally investigate the effects of liquid cross-flow velocity, gas flow rate, and orifice diameter on bubble formation. Data were taken mainly under reduced gravity conditions but some data were taken in normal gravity for comparison. The reduced gravity experiment was conducted aboard the NASA DC-9 Reduced Gravity Aircraft. The results show that the process of bubble formation and detachment depends on gravity, the orifice diameter (D(sub N)), the gas flow rate (Q(sub g)), and the liquid cross-flow velocity (U(sub L)). The reduced gravity data are shown. The data are analyzed based on a force balance, and two different detachment mechanisms are identified. When the gas momentum is large, the bubble detaches from the injection orifice as the gas momentum overcomes the attaching effects of liquid drag and inertia. The surface tension force is much reduced because a large part of the bubble pinning edge at the orifice is lost as the bubble axis is tilted by the liquid flow. When the gas momentum is small, the force balance in the liquid flow direction is important, and the bubble detaches when the bubble axis inclination exceeds a certain angle. With wall heating, liquid motion around an air bubble in cross-flowing 2cs silicone oil is experimentally investigated in 1-g. A spectral element based steady 2D numerical model is also developed. The traces of particles from experimental flow visualization and the corresponding computed streamlines are shown. At the upstream side of the bubble facing the cross-flow, thermocapillary and forced convection create liquid motion away from the wall, up along the surface. At the downstream side, a competing interaction between the two creates a recirculation cell, causing the bulk liquid to stagnate on the surface and separate thereafter. The important dimensionless parameters are - Surface tension and local cross-flow Reynolds numbers R(sub sigma)(U(sub ref)a/v) and Re(sub loc)(U(sub L)a/v), respectively based on reference thermocapillary U(sub ref)(sigma(sub T)Delta.T/mu, Delta T=T(sub wall)-T(sub liquid)) and local cross-flow velocity U(sub L), Prandtl number P(sub r) and Grashoff number Gr(rho.g.beta.DeltaTa(sup 3)/mu.v). Variation of the stagnation point with R(sub sigma) and Re(sub loc) is shown. Also shown are good agreement between experimental and numerical results in 1-g. The computational model is extended to mu-g condition to investigate temperature and velocity on the bubble surface, stagnation and reattachment points of the recirculation cell and wall heat transfer. It is observed that wall heating significantly alters the flow field around the bubble and thus the forces acting on the bubble, which control its detachment. Thus a combination of heating and liquid cross-flow can be utilized to precisely control bubble formation in a mu-g environment.
One phase of the large area crop inventory project is presented. Wheat yield models based on the input of environmental variables potentially obtainable through the use of space remote sensing were developed and demonstrated. By the use of a unique method for visually qualifying daily plant development and subsequent multifactor computer analyses, it was possible to develop practical models for predicting crop development and yield. Development of wheat yield prediction models was based on the discovery that morphological changes in plants are detected and quantified on a daily basis, and that this change during a portion of the season was proportional to yield.
In many passive visual tasks, human perceptual judgments are contrast dependent. To explore whether these contrast dependencies of visual perception also affect closed-loop manual control tasks, we examined visuomotor performance as humans actively controlled a moving luminance-defined line over a range of contrasts. Four subjects were asked to use a joystick to keep a horizontal line centered on a display as its vertical position was perturbed by a sum of sinusoids under two control regimes. The total root mean square (RMS) position error decreased quasi-linearly with increasing log contrast across the tested range (mean slope across subjects: -8.0 and -7.7% per log2 contrast, for the two control regimes, respectively). Frequency-response (Bode) plots showed a systematic increase in open-loop gain (mean slope: 1.44 and 1.30 dB per log2 contrast, respectively), and decrease in phase lag with increasing contrast, which can be accounted for by a decrease in response time delay (mean slope: 32 and 40 ms per log2 contrast, respectively). The performance data are well fit by a Crossover Model proposed by McRuer and Krendel, which allowed us to identify both visual position and motion cues driving performance. This analysis revealed that the position and motion cues used to support manual control under both control regimes appear equally sensitive to changes in stimulus contrast. In conclusion, our data show that active control of a moving visual stimulus is as dependent on contrast as passive perception and suggest that this effect is attributed to a shared contrast sensitivity early in the visual pathway, before any specialization for motion processing.
The chemical composition of interstellar grains is derived here on the basis of (1) the cosmic abundance of the elements; (2) the wavelength dependence of extinction and polarization; (3) the average total extinction; (4) the ratio of polarization to extinction; (5) the predominantly dielectric character of grains in the visible spectral region; and (6) infrared spectral characteristics of grains. Inferences of the core-mantle model with respect to spatial distribution are consistent with the proposition that growth of the mantles occurs in the galactic shock region predicted by the density-wave theory. Estimates of the total visual extinction toward the galactic center and the consequent estimates of the total amount of far infrared radiation are shown to depend critically on the grain model. Variations of the ratio of far ultraviolet to visual extinction are correlated with the conditions for growth of mantles on the bare small particles which are generally prevented from accreting mantles primarily because of their extreme temperature fluctuations produced by the ultraviolet photons in the radiation field.
BACKGROUND The Privacy Act of 1974 regulates the use a nd disclosure of personally identifiable information by US Federal agencies. The Act applies to biographical, financial, a nd other identity-linked information, a s well a s personal health information (PHI). As such, the use of astronaut PHI is limited to authorized personnel for preapproved uses, with data reporting often limited to aggregated information about groups. These limitations on the use a nd reporting of astronaut PHI complicates surveillance efforts, wherein epidemiologists a t the National Aeronautics and Space Administration (NASA)monitor the incidence of targeted health conditions in the astronaut population, or to discover emerging trends of aging and disease. Stratification on one or more covariates –particularly time-period, sex, a nd mission participation –can lead to extremely small datasets such that the reporting of results is potentially attributable to individuals. An additional challenge is the small size of the astronaut population, both in terms of numbers of individuals a s well a s in terms of density of exposure time. Such small datasets yield volatile rate estimates that are difficult to interpret. To a id the epidemiological surveillance efforts, a surveillance tool is required that can (a) satisfy the need for rapid computation of condition-specific incidence and mortality rates; (b) improve the statistical estimates of these estimated rates; and (c) maintain astronaut privacy. Here we describe a nd demonstrate such a tool. METHODS We devised a system that models incidence a nd mortality rates rather than calculating them directly. This ha s the advantage of using all the available data to derive the estimates, lea ding to rates that a re not attributable to any one individual, a nd a re a s numerically stable a s they can be given the extremely limited data. The system models disease endpoints using a Poisson regression model with exposure density (measured in person-years) a s a n offset term. By doing so the model is estimating event counts per person-year, equivalent to modeling the rates directly. It uses a standard (pre-specified)set of covariates; the system does not engage in “model-building” as model parsimony is not the goa l. Instead, it is explicitly recognized that if a covariate is not statistically significant a nd not a confounder then it will likely have very little effect on the estimate of the incidence a nd mortality rates. Users are able to specify the disease endpoint of interest and the covariates over which they would like to stratify. The system then uses the resulting model to compute the estimated rates for the user-chosen configuration of variables as visualizes those either over an age range within a specified time-period, or over time for astronauts with a specified age range. RESULTS The first iteration of the tool computes incidence a nd mortality rates for cardiovascular conditions and cancers. Code ha s been developed to retrieve the appropriate data from the IMPALA analysis platform, compute the models for incidence a nd mortality, a nd then use those models to generate the corresponding rate curves. A companion graphical user interface allows the user to specify the curves and visualize the results. CONCLUSIONS It is important to note that the rapid surveillance tool described here is neither meant to be a definitive assessment of the incidence or mortality of any particular disease or condition in the astronaut population, nor is it meant to be used for research purposes. Rather, it is meant as an early indicator that in-depth investigation may be warranted. By automating a repetitive process and leveraging carefully curated astronaut health outcomes, the tool makes possible a rapid “first look” into known areas of concern, and, if used judiciously, may surface new areas of concern for long-term astronaut health. This work is supported in part by the Translational Research Institute for Space Health (TRISH) through NASA Cooperative Agreement NNX16AO69A.
Nitric oxide planar laser-induced fluorescence (NO PLIF) has been used to visualize the flow on the aft-body of an entry capsule having an activated RCS jet in NASA Langley Research Center's 31-Inch Mach 10 wind tunnel facility. A capsule shape representative of the Apollo command module was tested. These tests were performed to demonstrate the ability of the PLIF method to visualize RCS jet flow while providing some preliminary input to NASA's Orion Vehicle design team. Two different RCS nozzle designs - conical and contoured - were tested. The conical and contoured nozzles had area ratios of 13.4 and 22.5 respectively. The conical nozzle had a half-angle of 10 . Low- and high-Reynolds number cases were investigated by changing the tunnel stagnation pressure from 350 psi to 1300 psi, resulting in freestream Reynolds numbers of 0.56 and 1.8 million per foot respectively. For both of these cases, three different jet plenum pressures were tested (nominally 56, 250 and 500 psi). A single angle-of-attack was investigated (24 degrees). NO PLIF uses an ultraviolet laser sheet to interrogate a slice in the flow containing seeded NO; this UV light excites fluorescence from the NO molecules which is detected by a high-speed digital camera. The system has spatial resolution of about 200 microns (2 pixel blurring) and has flow-stopping time resolution (approximately 1 microsecond). NO was seeded into the flow two different ways. First, the RCS jet fluid was seeded with approximately 1-5% NO, with the balance N2. This allowed observation of the shape, structure and trajectory of the RCS jets. Visualizations of both laminar and turbulent flow jet features were obtained. Visualizations were obtained with the tunnel operating at Mach 10 and also with the test section held at a constant pressure similar to the aftbody static pressure (0.04 psi) obtained during tunnel runs. These two conditions are called "tunnel on" and "tunnel off" respectively. Second, the forebody flow was seeded with a very low flowrate (<100 standard cubic centimeters per minute) of pure NO. This trace gas was entrained into and allowed visualization of the shear layer forming between the expansion fan on the shoulder of the model and the recirculating separated flow in the wake of the model. This shear layer was observed to be laminar in the absence of the RCS jet operation and turbulent above a certain RCS jet flowrate. Furthermore, the operation of the RCS jet is seen to push the shear layer out away from the model, with a higher jet pressures resulting in larger deflections. Figures show some data from this test, partially processed. In the final paper, these images will be processed and rendered on a three dimensional visualization of the test hardware for clearer visualization and interpretation of the flowfields.
The Bidirectional Reflectance Distribution Function (BRDF) is a fundamental concept for characterizing the reflectance property of a surface, and helps in the analysis of remote sensing data from satellite, airborne and surface platforms. Multi-angular remote sensing measurements are required for the development and evaluation of BRDF models for improved characterization of surface properties. However, multi-angular data and the associated BRDF models are typically multidimensional involving multi-angular and multi-wavelength information. Effective visualization of such complex multidimensional measurements for different wavelength combinations is presently somewhat lacking in the literature, and could serve as a potentially useful research and teaching tool in aiding both interpretation and analysis of BRDF measurements. This article describes a newly developed software package in Python (PolarBRDF) to help visualize and analyze multi-angular data in polar and False Color Composite (FCC) forms. PolarBRDF also includes functionalities for computing important multi-angular reflectance/albedo parameters including spectral albedo, principal plane reflectance and spectral reflectance slope. Application of PolarBRDF is demonstrated using various case studies obtained from airborne multi-angular remote sensing measurements using NASA's Cloud Absorption Radiometer (CAR). Our visualization program also provides functionalities for untangling complex surface/atmosphere features embedded in pixel-based remote sensing measurements, such as the FCC imagery generation of BRDF measurements of grasslands in the presence of wild fire smoke and clouds. Furthermore, PolarBRDF also provides quantitative information of the angular distribution of scattered surface/atmosphere radiation, in the form of relevant BRDF variables such as sunglint, hotspot and scattering statistics.
An Earth System Digital Twin (ESDT) is a dynamic, interactive, digital replica of the state and temporal evolution of Earth systems. It integrates multiple models along with observation data, and connecting them with analysis, AI, and visualization tools. Together, these enable users to explore the current state of the Earth system, predict future conditions, and run hypothetical scenarios to understand how the system would evolve under various assumptions. The NASA’s Advanced Information Systems Technology (AIST)’s Integrated Digital Earth Analysis System (IDEAS) project is to establish an extensible architectural solution to develop digital twins of our physical environment for Earth Science. IDEAS delivers a formal system architecture with mechanisms for the outputs of one model to feed into others; for driving models with observation data; and for harmonizing observation data and model outputs for analysis. To validate and demonstrate the IDEAS architecture, this project collaborates with the Space Climate Observatory (SCO)’s FloodDAM project and the Centre National d’Etudes Spatiales (CNES) to focus on floods detection, prediction and their impacts.
Vector field visualization techniques are essential to help us understand the complex dynamics of flow fields. These can be found in a wide range of applications such as study of flows around an aircraft, the blood flow in our heart chambers, ocean circulation models, and severe weather predictions. The vector fields from these various applications can be visually depicted using a number of techniques such as particle traces and advecting textures. In this tutorial, we present several fundamental algorithms in flow visualization including particle integration, particle tracking in time-dependent flows, and seeding strategies. For flows near surfaces, a wide variety of synthetic texture-based algorithms have been developed to depict near-body flow features. The most common approach is based on the Line Integral Convolution (LIC) algorithm. There also exist extensions of LIC to support more flexible texture generations for 3D flow data. This tutorial reviews these algorithms. Tensor fields are found in several real-world applications and also require the aid of visualization to help users understand their data sets. Examples where one can find tensor fields include mechanics to see how material respond to external forces, civil engineering and geomechanics of roads and bridges, and the study of neural pathway via diffusion tensor imaging. This tutorial will provide an overview of the different tensor field visualization techniques, discuss basic tensor decompositions, and go into detail on glyph based methods, deformation based methods, and streamline based methods. Practical examples will be used when presenting the methods; and applications from some case studies will be used as part of the motivation.
NASA’s Artemis campaign is making heavy use of simulation to help return humans to the lunar surface by the end of the decade. There are several aspects of the lunar surface and its environment which must be accurately modeled before these simulations can be relied upon to influence decisions being made under these programs. Digital Lunar Exploration Sites, a paper submitted to the 2022 IEEE Aerospace Conference, outlined the process used to generate the lunar surface in a digital environment. This paper will expand upon this topic and delve into the steps being taken by the NASA Exploration Systems Simulations (NExSyS) team at NASA’s Johnson Space Center (JSC) to properly verify and validate these simulations, with a focus on the visual aspects of the environment. Natural lighting validation relies in part on the wealth of data generated during the Apollo program. Many images taken by Apollo astronauts on the lunar surface have been replicated in the simulated environments to gain confidence in the accuracy of terrain and lighting models. However, because the environment the Artemis astronauts will experience at the Lunar South Pole (LSP) is dissimilar from the near-equatorial Apollo sites, other validation techniques must be applied. At the LSP, the sun crests only about three degrees above the horizon and when combined with the lack of a lunar atmosphere, lighting in this region is often very different than what a human would experience on Earth. Solar illumination, earthshine, human eye response, solar blooming, lunar regolith optical properties, and shadows cast by rocks and crater walls will play a significant role in an astronaut’s ability to safely conduct an Extra-Vehicular Activity (EVA) or perform a traverse with a lunar rover. Approaches for validation of these aspects of the rendered LSP environment are considered in this paper. In addition to natural lighting, approaches for the validation of artificial lighting models at the LSP are discussed. The JSC Lighting Lab has been studying the illumination profile of the Exploration Infomatics Subsystem (xINFO) lighting on the Exploration EVA Mobility Unit (xEMU). How these lights interact with the solar illumination and the shadows being cast on the lunar surface is of particular interest, so the validity of models representing these lights in a human-in-the-loop virtual reality environment becomes very important. This paper also touches on some of the simulation performance considerations when a Human in the Loop (HITL) is present, which drives the need for real time rendering of the environment. Natural and artificial lighting will play a crucial role to decisions being made when planning and executing missions at the Lunar South Pole (LSP) and it is vitally important to understand the LSP environment before we return.