Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solar Cells”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57

Spectral binning for energy production calculations and multijunction solar cell design

Currently, most solar cells are designed for and evaluated under standard spectra intended to represent typical spectral conditions. However, no single spectrum can capture the spectral variability needed for annual energy production (AEP) calculations, and this shortcoming becomes more significant for series-connected multijunction cells as the number of junctions increases. For this reason, AEP calculations are often performed on very detailed yearlong sets of data, but these pose 2 inherent challenges: (1) These data sets comprise thousands of data points, which appear as a scattered cloud of data when plotted against typical parameters and are hence cumbersome to classify and compare, and (2) large sets of spectra bring with them a corresponding increase in computation or measurement time. Here, we show how a large spectral set can be reduced to just a few 'proxy' spectra, which still retain the spectral variability information needed for AEP design and evaluation. The basic 'spectral binning' methods should be extensible to a variety of multijunction device architectures. In this study, as a demonstration, the AEP of a 4-junction device is computed for both a full set of spectra and a reduced proxy set, and the results show excellent agreement for as few as 3 proxy spectra. This enables much faster (and thereby more detailed) calculations and indoor measurements and provides a manageable way to parameterize a spectral set, essentially creating a 'spectral fingerprint,' which should facilitate the understanding and comparison of different sites.

14 SOLAR ENERGY↗

No Evidence for Passivation Effects of Na and K at Grain Boundaries in Polycrystalline Cu(In,Ga)Se2 Thin Films for Solar Cells

Thin-film solar cells based on Cu(In,Ga)Se2 (CIGSe) absorber layers reach conversion efficiencies of above 20%. One key to this success is the incorporation of alkali metals, such as Na and K, into the surface and the volume of the CIGSe thin film. The present work discusses the impact of Na and K on the grain-boundary (GB) properties in CIGSe thin films, i.e., on the barriers for charge carriers, ..phi..b, and on the recombination velocities at the GBs, sGB. First, the physics connected with these two quantities as well as their impact on the device performance are revised, and then the values for the barrier heights and recombination velocities are provided from the literature. The sGB values are measured by means of a cathodoluminescence analysis of Na-/K-free CIGSe layers as well as on CIGSe layers on Mo/sapphire substrates, which are submitted to only NaF or only KF postdeposition treatments. Overall, passivating effects on GBs by neither Na nor K can be confirmed. The GB recombination velocities seem to remain on the same order of magnitude, in average about 10^3-10^4 cm s^-1, irrespective of whether CIGSe thin films are Na-/K-free or Na-/K-containing.

14 SOLAR ENERGY↗

Cost-Efficiency balanced polymer acceptors based on lowly fused Dithienopyrrolo[3, 2b]benzothiadiazole for 16.04% efficiency All-Polymer solar cells

All-polymer solar cells (All-PSCs) attracted increasing attention due to the outstanding thermal stability and mechanical properties. The current prevailing polymer acceptors for most efficient All-PSCs are polymerized high-performance small molecule acceptor of Y6, i.e. the dithienothiopheno[3,2-b]-pyrrolobenzothiadiazole (BTTP) based polymers. However, the BTTP-based polymers often show relatively shallow highest occupied molecular orbital (HOMO) energy level and high figure of merit (FOM), which limit the rational selection of paring donor polymers. Herein, we presented two low-cost polymer acceptors, namely as BTP-T2F and BTP-2T2F, based on lowly fused dithienopyrrolo[3,2b]benzothiadiazole (BTP, removing two thiophene cycles from BTTP). Here the BTP-based polymers exhibited deeper HOMO levels around –5.90 eV, which could match variable donor polymers with low-lying HOMO levels, such as low-cost PTQ10. Additionally, the synthesis was significantly simplified compared to BTTP-based polymers. A power conversion efficiency (PCE) of 14.32% was achieved in binary blend device containing PTQ10:BTP-2T2F. By adding a miscibility-enhancing PBDTCl-TPD as a third component, the top PCE of 16.04% was obtained in ternary blend All-PSCs. Combining the high device performance and low estimated cost, extraordinary cost-efficiency balance was realized within these BTP-based polymer acceptors.

36 MATERIALS SCIENCE↗

Towards linking lab and field lifetimes of perovskite solar cells

Metal halide perovskite solar cells (PSCs) represent a promising low-cost, thin-film photovoltaic (PV) technology, with unprecedented power conversion efficiencies (PCEs) obtained for both single-junction and tandem applications. To push PSCs toward commercialization, it is critical, albeit challenging, to understand device reliability under real-world outdoor conditions where multiple stress factors (e.g., light, heat, humidity) coexist, generating complicated degradation behaviors. It is necessary to identify accelerated indoor testing protocols - which can correlate specific stressors with observed degradation modes in fielded devices - to quickly guide PSC development. Here, we use a state-of-the-art p-i-n PSC stack (with PCE up to ~25.5%) to show that indoor accelerated stability tests can predict our 6-month outdoor aging tests. Device degradation rates under illumination and at elevated temperatures are most instructive for understanding outdoor device reliability. Further, we also find that the indium tin oxide (ITO)/self-assembled monolayer (SAM)-based hole transport layer (HTL)/perovskite interface most strongly affects our device operation stability. Improving the ion-blocking properties of the SAM HTL increases averaged device operational stability at 50 degree C-85 °C by a factor of ~2.8, reaching over 1000 h at 85 °C and to near 8200 h at 50 °C with a projected 20% degradation, which is among the best to date for high-efficiency p-i-n PSCs.

14 SOLAR ENERGY↗

Improving Miscibility of Polymer Donor and Polymer Acceptor by Reducing Chain Entanglement for Realizing 18.64 % Efficiency All Polymer Solar Cells

All-polymer solar cells have experienced rapid development in recent years by the emergence of polymerized small molecular acceptors (PSMAs). However, the strong chain entanglements of polymer donors (P D s) and polymer acceptors (P A s) decrease the miscibility of the resulting polymer mixtures, making it challenging to optimize the blend morphology. Herein, we designed three P A s, namely PBTPICm-BDD, PBTPICγ-BDD and PBTPICF-BDD, by smartly using a BDD unit as the polymerized unit to copolymerize with different Y-typed non-fullerene small molecular acceptors (NF-SMAs), thus achieving a certain degree of distortion and giving the polymer system enough internal space to reduce the entanglements of the polymer chains. Such effects increase the chances of the P D being interspersed into the acceptor material, which improve the solubility between the P D and P A . The PBTPICγ-BDD and PBTPICF-BDD displayed better miscibility with PBQx-TCl, leading to a well optimized morphology. As a result, high power conversion efficiencies (PCEs) of 17.50 % and 17.17 % were achieved for PBQx-TCl : PBTPICγ-BDD and PBQx-TCl : PBTPICF-BDD devices, respectively. In conclusion, with the addition of PYFT-o as the third component into PBQx-TCl : PBTPICγ-BDD blend to further extend the absorption spectral coverage and finely tune microstructures of the blend morphology, a remarkable PCE of 18.64 % was realized finally.

36 MATERIALS SCIENCE↗

Optimalization activity of ZnO NR/TiO2 NR-P3HT as an active layer based on hybrid bulk heterojunction on dye sensitized solar cell (DSSC)

Dye sensitized solar cell (DSSC) with metal inorganic and conjugated organic polymer mixture, ZnO NR/TiO{sub 2} NR-P3HT as an active layer based on hybrid bulk heterojunction has been studied. The hybrid material was used to optimize DSSC performs for better efficiency than only TiO{sub 2} as an electrode. Synthesis of TiO{sub 2} nanorods (NR) was conducted by ball milling 1000 rpm for 4 hours and strong base reaction by hydrothermal process at 120 °C overnight. And the ZnO NR was synthesized from Zn(NO{sub 3}){sub 2}.4H{sub 2}O precusor by hydrotermal process at 90 °C for 5 hours and calcined on various temperature s of 400, 600, and 800 °C. ZnO NR was coated into an Tndium Tin Oxide (TTO) glass to collecting electron s effectively, where TiO{sup 2} NR were incorporated with poly(3 -hexylthiophene) (P3HT) on various concentration s of 5, 10, 15 mg/mL to obtain a larger surface area. Material characterization were performed by X -Ray Diffraction (XRD) and Uv-Vis spectrophotometer. For an application of DSSC were measured by T-V Keithley Multimeter and the efficiency of DSSC at various P3HT’s concentrations of 5, 10, 15 mg/mL were 7.44 × 10{sup −3}, 0.0114, 0.0104, respectively. The maximum efficiency of DSSC was showed when TiO{sup 2} NR-P3HT’s concentration was 10 mg/mL.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Surface reaction for efficient and stable inverted perovskite solar cells

We report perovskite solar cells (PSCs) with an inverted structure (often referred to as the p-i-n architecture) are attractive for future commercialization due to their easily scalable fabrication, reliable operation, and compatibility with a wide range of perovskite-based tandem device architectures. However, the power conversion efficiency (PCE) of p-i-n PSCs falls behind n-i-p (or normal) structure counterparts. This large performance gap could undermine efforts to adopt p-i-n architectures, despite their other advantages. Given the remarkable advances in perovskite bulk materials optimization over the past decade, interface engineering has become the most important strategy to push PSC performance to its limit. Here, we report a reactive surface engineering approach based on a simple post-growth treatment of 3-(Aminomethyl)pyridine (3-APy) on top of a perovskite thin film. First, the 3-APy molecule selectively reacts with surface FA+, reducing perovskite surface roughness and surface potential fluctuations associated with surface steps/terraces. Second, the reaction product on the perovskite surface decreases the formation energy of charged iodine-vacancies, leading to effective n-type doping with a reduced work function in the surface region. With this reactive surface engineering, the resulting p-i-n PSCs obtained a PCE over 25%, along with retaining 87% of the initial PCE after over 2400 h of one-sun operation at about 55 degrees C in air.

14 SOLAR ENERGY↗

Pathway for recovery of photo-degraded polymer solar cells by post degradation thermal anneal

The photo-degradation of polymer solar cells is a critical challenge preventing its commercial deployment. We experimentally fabricate organic solar cells and characterize their degradation under solar simulators in an environmental chamber under nitrogen flow, without exposure to oxygen and moisture. We have developed a thermally stable inverted organic solar cell architecture in which light induced degradation of device characteristics can be reversibly annealed to the pristine values. The stable inverted cells utilized MoO x layers that are thermally treated immediately after their deposition on the organic layer, and before metal cathode deposition. Organic solar cells that are photo-degraded in the presence of oxygen, however show irreversible degradation that cannot be thermally recovered. The decrease of organic solar cell characteristics correlates with increases in mid-gap electronic states, measured using capacitance spectroscopy and dark current. It is likely the photo-induced defect states caused by local H motion from the alkyl chains to the aromatic backbone, can be reversibly annealed at elevated temperatures after photo-degradation. Finally, our results provide a pathway for improving the stability of organic photovoltaics.

14 SOLAR ENERGY↗

Investigation of accelerated stress factors and failure/degradation mechanisms in terrestrial solar cells

Research on the reliability of terrestrial solar cells was performed to identify failure/degradation modes affecting solar cells and to relate these to basic physical, chemical, and metallurgical phenomena. Particular concerns addressed were the reliability attributes of individual single crystalline, polycrystalline, and amorphous thin film silicon cells. Results of subjecting different types of crystalline cells to the Clemson accelerated test schedule are given. Preliminary step stress results on one type of thin film amorphous silicon (a:Si) cell indicated that extraneous degradation modes were introduced above 140 C. Also described is development of measurement procedures which are applicable to the reliability testing of a:Si solar cells as well as an approach to achieving the necessary repeatability of fabricating a simulated a:Si reference cell from crystalline silicon photodiodes.

Lathrop, J. W.↗

Method of manufacturing a hybrid emitter all back contact solar cell

A method of manufacturing an all back contact solar cell which has a hybrid emitter design. The solar cell has a thin dielectric layer formed on a backside surface of a single crystalline silicon substrate. One emitter of the solar cell is made of doped polycrystalline silicon that is formed on the thin dielectric layer. A second emitter of the solar cell is formed in the single crystalline silicon substrate and is made of doped single crystalline silicon. The method further includes forming contact holes that allow metal contacts to connect to corresponding emitters.

14 SOLAR ENERGY↗

Geometries, Electronic Structures, And Spectral Properties Of Some Metal Free Phthalonitrile Derivatives For Enhancement Of The Dye Sensitized Solar Cells

New technologies for direct solar energy conversion have gained more attention in the last few years. In particular, Dye Sensitized Solar Cells (DSSCs) are promising in terms of efficiency and low cost [1,2]. Benefited from systematic device engineering and continuous material innovation, a state of the art DSC with a ruthenium sensitizer has achieved a validated efficiency of 11.1%[3] measured under the air mass 1.5 global (AM1.5G) conditions.The optimized geometries of the 3, 4-Pyridinedicarbonitrile, 3-Aminophthalonitrile, 4-Aminophthalonitrile and 4-Methylphthalonitrile are shown in Fig. 1(a). The frontier molecular orbitals (MO) energies of the dyes 3, 4 Pyridinedicarbonitrile, 3-Nitrophthalonitrile, 4-Aminophthalonitrile and 4-Methylphthalonitrile are shown in Fig. 1(b). The HOMO-LUMO gap of the dye 3, 4 Pyridinedicarbonitrile, 3-Aminophthalonitrile, 4-Aminophthalonitrile and 4-Methylphthalonitrile in vacuum is 5.96 eV, 5.54 eV, 5.57 eV, 5.76 eV respectively. The geometries, electronic structures, polarizabilities, and hyperpolarizabilities of dyes 3, 4-Pyridinedicarbonitrile, 4-Aminophthalonitrile and 4-Methylphthalonitrile were studied by using density functional theory with hybrid functional B3LYP, and the UV-Vis spectra were investigated by using TDDFT methods. The NBO results suggest that 3, 4-Pyridinedicarbonitrile, 3-Aminophthalonitrile 4-Aminophthalonitrile and 4-Methylphthalonitrile are all (D-pi-A) systems. The calculated isotropic polarizability of 3, 4-Pyridinedicarbonitrile, 3-Aminophthalonitrile, 4-Aminophthalonitrile and 4-Methylphthalonitrile is. 85.76, 112.72, 26.63 and 115.13 a.u., respectively. The calculated polarizability anisotropy invariant of 3, 4-Pyridinedicarbonitrile, 3-Aminophthalonitrile, 4-Aminophthalonitrile and 4-Methylphthalonitrile is 74.451, 83.533, 62.653 and 88.526 a.u., respectively. The hyperpolarizabilities of 3, 4-Pyridinedicarbonitrile, 3-Aminophthalonitrile, 4-Aminophthalonitrile and 4-Methylphthalonitrile is 0.80628, 5.60646, 7.7979 and 1.86216 (in a.u.), respectively. The frequencies of strongest IR absorption for 3, 4-Pyridinedicarbonitrile, 3-Aminophthalonitrile, 4-Aminophthalonitrile and 4-Methylphthalonitrile are 1614 cm{sup -1}, 290 cm{sup -1}, 387 cm{sup -1} and 846 cm{sup -1} and the frequencies of strongest Raman activity for 3, 4-Pyridinedicarbonitrile, 3-Aminophthalonitrile, 4-Aminophthalonitrile and 4-Methylphthalonitrile are 2345 cm{sup -1}, 2338 cm{sup -1},2329 cm{sup -1}, 2337cm{sup -1}, respectively. The electronic absorption spectral features in visible and near-UV region were assigned based on the qualitative agreement to TDDFT calculations. The absorptions are all ascribed to {pi}{yields}{pi}* transition. The three excited states with the lowest excited energies of 3, 4-Pyridinedicarbonitrile, 3-Aminophthalonitrile, 4-Aminophthalonitrile and 4-Methylphthalonitrile are photoinduced electron transfer processes that contributes sensitization of photo-to-current conversion processes. The interfacial electron transfer between semiconductor TiO{sub 2} electrode and dye sensitizer 3, 4- Pyridinedicarbonitrile, 3-Aminophthalonitrile, 4-Aminophthalonitrile and 4-Methylphthalonitrile is electron injection process from excited dyes as donor to the semiconductor conduction band. Based on the comparative analysis of geometries, electronic structures, and spectrum properties between 3, 4-Pyridinedicarbonitrile, 3-Aminophthalonitrile, 4-Aminophthalonitrile and 4-Methylphthalonitrile the role of amide and methyl groups in phthalonitrile is as follows: it enlarged the distance between electron donor group and semiconductor surface, and decreased the timescale of the electron injection rate, resulted in giving lower conversion efficiency. This indicates that the choice of the appropriate conjugate bridge in dye sensitizer is very important to enhance the performance of DSSC.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

A V-grooved GaAs solar cell

V-grooved GaAs solar cells promise the benefits of improved optical coupling, higher short-circuit current, and incrased tolerance to particle radiation compared to planar cells. A GaAs homojunction cell was fabricated by etching a V-groove pattern into an n-epilayer (2.1 x 10 to the 17th power per cu cm) grown by metalorganic chemical vapor deposition (MOCVD) on an n+ substrate (2.8 x 10 to the 18th power per cu cm) and then depositing an MOCVD p epilayer (4.2 x 10 to the 18th power per cu cm). Reflectivity measurements on cells with and without an antireflective coating confirm the expected decrease in reflectance of the microgrooved cell compared to the planar structure. The short-circuit current of the V-grooved solar cell was 13 percent higher than that of the planar control.

Bailey, S. G.↗

Routes for realizing high-performing Si solar cells by using periodic structures

Highlights: • The record high-efficiency of 16.9% for periodically patterned Si solar cells. • Optical and electrical benefits of periodic microscale Si structures. • Design routes for realizing high-performing periodic Si solar cells. - Abstract: Theoretical suggestion indicated the substantial improvement of solar cells by using periodic structures. Yet, the promise has not been practically realized due to the lack of electrical analyses of periodical light-absorbing structure. Here, we report the record high-efficiency of 16.9% for periodically patterned silicon (Si) solar cells. Periodic Si micro-pillars were fabricated for large-scale solar cells. The Si pillars with a height of about 5 μm provided significantly enlarged light-active surface, which improved the photo-generated carrier collection efficiency. From optical aspects, the pillar structures reduced light reflection and hence effectively drove more photons into the absorber layer. Additionally, the enhanced pillar-structured Si surface definitely contributed to reduce an electrical resistance of a solar cell. We demonstrated that the surficial enhanced Si design could be a promising approach for high-efficient solar cell applications. We may suggest a route for the optimum electrical designs of periodic structured solar cells.

36 MATERIALS SCIENCE↗

Non-Linear Luminescent Coupling in Series-Connected Multijunction Solar Cells

The assumption of superposition or linearity of photocurrent with solar flux is widespread for calculations and measurements of solar cells. The well-known effect of luminescent coupling in multijunction solar cells has also been assumed to be linear with excess current. Here we show significant non-linearities in luminescent coupling in III-V multijunction solar cells and propose a simple model based on competition between radiative and nonradiative processes in the luminescent junction to explain these non-linearities. We demonstrate a technique for accurately measuring the junction photocurrents under a specified reference spectrum, that accounts for and quantifies luminescent coupling effects.

14 SOLAR ENERGY↗

Progress towards a 30% efficient GaInP/Si tandem solar cells

The performance of dual-junction solar cells with a Si bottom cell has been investigated both theoretically and experimentally. Simulations show that adding a top junction with an energy bandgap of 1.6 -1.9 eV to a standard silicon solar cell enables efficiencies over 38%. Currently, top junctions of GaInP (1.8 eV) are the most promising as they can achieve 1-sun efficiencies of 20.8% [1]. We fabricated mechanically stacked, four terminal GaInP/Si tandem solar cells using a transparent adhesive between the subcells. These tandem devices achieved an efficiency of 27% under AM1.5 g spectral conditions. Furthermore, higher efficiencies can be achieved by using an improved Si-bottom cell and by optimizing the dual-junction device for long-wavelength light and luminescent coupling between the two junctions.

14 SOLAR ENERGY↗

Does non-reciprocity break the Shockley–Queisser limit in single-junction solar cells?

The efficiency of single-junction solar cells is bounded by the Shockley–Queisser limit of 41%. However, standard derivation for this limit constrains the system to be reciprocal, and what non-reciprocity can bring for single-junction solar cells remains yet to be clarified. Here, we prove that even with non-reciprocity, the ultimate efficiency of single-junction solar cells is still subject to the Shockley–Queisser limit. Here, we show that the Shockley–Queisser limit does not rely on the detailed balance, but rather is a consequence of the integrated balance between the absorption and emission processes, as required by the second law of thermodynamics.

14 SOLAR ENERGY↗

Improved Schottky barrier solar cells

Schottky barrier (SB) solar cells have been fabricated for solar energy conversion using GaAs and GaAs 0.78P0.22. Conversion efficiencies of 9% for air mass zero and 12% for terrestrial sun were observed for antireflection coated GaAs0.78P0.22 SB cells. The corresponding efficiencies for GaAs SB cells were 7% and 10%, respectively. These efficiencies are for cells with no interfacial layer effect. The short circuit current density for GaAs SB cells has been improved. The use of an ellipsometer to determine the optimum antireflection coating parameters is illustrated.

Yeh, Y.-C. M.↗