Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solar Cell”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57

Development of Lattice-Matched 1.7 eV GalnAsP Solar Cells Grown on GaAs by MOVPE

To advance the state-of-the-art in III-V multijunction solar cells towards high concentration efficiencies approaching 50%, development of a high-quality ~1.7 eV second junction solar cell is of key interest for integration in five or more junction devices. Quaternary GalnAsP solar cells grown lattice-matched on GaAs allows bandgap tunability in the range from 1.42 to 1.92 eV and offers an attractive Al-free alternative to conventional AlGaAs solar cells. In this work, we investigate the role of growth temperature towards understanding the optimal growth window for realizing high-quality GalnAsP alloys. We demonstrate bandgap tunability from 1.6 to 1.8 eV in GalnAsP alloys for compositions close to the miscibility gap, while still maintaining lattice-matched condition to GaAs. We perform an in-depth investigation to understand the impact of varying base thickness and doping concentration on the carrier collection and performance of these 1.7 eV GalnAsP solar cells. The photo-response of these cells is found to be very sensitive to p-type zinc dopant incorporation in the base layer. We demonstrate prototype 1.7 eV GalnAsP solar cell designs that leverage enhanced depletion width as an effective method to overcome this issue and boost long-wavelength carrier collection. Short-circuit current density (JSC) measured in field-aided devices were as high as 17.25 m A/cm2. The best GalnAsP solar cell in this study achieved an efficiency of 17.2% with a JSC of 17 m A/cm2 and a fill-factor of 86.4%. The corresponding open-circuit voltage (VOC) 1.7 eV measured on this cell represents the highest Voc reported for a 1.7 eV GalnAsP solar cell. These initial cell results are encouraging and highlight the potential of Al-free GalnAsP solar cells for integration in the next generation of III-V multijunction solar cells.

14 SOLAR ENERGY↗

A Low Cost Weather Balloon Borne Solar Cell Calibration Payload

Calibration of standard sets of solar cell sub-cells is an important step to laboratory verification of on-orbit performance of new solar cell technologies. This paper, looks at the potential capabilities of a lightweight weather balloon payload for solar cell calibration. A 1500 gr latex weather balloon can lift a 2.7 kg payload to over 100,000 ft altitude, above 99% of the atmosphere. Data taken between atmospheric pressures of about 30 to 15 mbar may be extrapolated via the Langley Plot method to 0 mbar, i.e. AMO. This extrapolation, in principle, can have better than 0.1 % error. The launch costs of such a payload arc significantly less than the much larger, higher altitude balloons, or the manned flight facility. The low cost enables a risk tolerant approach to payload development. Demonstration of 1% standard deviation flight-to-flight variation is the goal of this project. This paper describes the initial concept of solar cell calibration payload, and reports initial test flight results. .

Snyder, David B.↗

Results of the 1973 NASA/JPL balloon flight solar cell calibration program

High altitude balloon flights carried 37 standard solar cells for calibration above 99.5 percent of the earth's atmosphere. The cells were assembled into standard modules with appropriate resistors to load each cell at short circuit current. Each standardized module was mounted at the apex of the balloon on a sun tracker which automatically maintained normal incidence to the sun within 1.0 deg. The balloons were launched to reach a float altitude of approximately 36.6 km two hours before solar noon and remain at float altitude for two hours beyond solar noon. Telemetered calibration data on each standard solar cell was collected and recorded on magnetic tape. At the end of each float period the solar cell payload was separated from the balloon by radio command and descended via parachute to a ground recovery crew. Standard solar cells calibrated and recovered in this manner are used as primary intensity reference standards in solar simulators and in terrestrial sunlight for evaluating the performance of other solar cells and solar arrays with similar spectral response characteristics.

Yasui, R. K.↗

Enhanced conversion efficiency in wide-bandgap GaNP solar cells

In this study, we demonstrate –2.05 eV dilute nitride GaNP solar cells on GaP substrates for potential use as the top junction in dual-junction integrated cells on Si. By adding a small amount of N into indirect-bandgap GaP, GaNP has several extremely important attributes: a direct-bandgap that is also tunable, and easily attained lattice-match with Si. Our best GaNP solar cell ([N] –1.8%, E g –2.05 eV) achieves an efficiency of 7.9%, even in the absence of a window layer. This GaNP solar cell's efficiency is 3× higher than the most efficient GaP solar cell to date and higher than other solar cells with similar direct bandgap (InGaP, GaAsP). Through a systematic study of the structural, electrical, and optical properties of the device, efficient broadband optical absorption and enhanced solar cell performance are demonstrated.

14 SOLAR ENERGY↗

Production technology for high efficiency ion implanted solar cells

Ion implantation is being developed for high volume automated production of silicon solar cells. An implanter designed for solar cell processing and able to properly implant up to 300 4-inch wafers per hour is now operational. A machine to implant 180 sq m/hr of solar cell material has been designed. Implanted silicon solar cells with efficiencies exceeding 16% AM1 are now being produced and higher efficiencies are expected. Ion implantation and transient processing by pulsed electron beams are being integrated with electrostatic bonding to accomplish a simple method for large scale, low cost production of high efficiency solar cell arrays.

Kirkpatrick, A. R.↗

Influence of Annealing in Freon on the Crystalline Structure of Cadmium-Telluride Layers and the Efficiency of Thin-Film Solar Cells on Their Basis

Solar cells (SCs) based on cadmium-telluride base layers, obtained by thermal evaporation and closed-space sublimation (CSS), are investigated. The base layers are activated via annealing in Freon. Structural and morphological studies are carried out to compare the recrystallization processes occurring during annealing in CdTе layers fabricated by different methods. The output parameters and light diode characteristics of the SCs are investigated, and the possibility of applying Freon annealing in the commercial production technology of thin-film CdS/CdTе SCs with base layers formed by thermal vacuum evaporation is analyzed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Electrochemically grown ZnO nanorods for hybrid solar cell applications

A hybrid solar cell is designed and proposed as a feasible and reasonable alternative, according to acquired efficiency with the employment of zinc oxide (ZnO) nanorods and ZnO thin films at the same time. Both of these ZnO structures were grown electrochemically and poly(3-hexylthiophene):phenyl-C61-butyric acid methyl ester; (P3HT:PCBM) was used as an active polymer blend, which was found to be compatible to prepared indium-tin-oxide (ITO) substrate base. This ITO base was introduced with mentioned ZnO structure in such a way that, the most efficient configuration was optimized to be ITO/ZnO film/ZnO nanorod/P3HT: PCBM/Ag. Efficiency of this optimized device is found to be 2.44%. All ZnO works were carried out electrochemically, that is indeed for the first time and at relatively lower temperatures. (author)

14 SOLAR ENERGY↗

Parameters influencing the deposition of methylammonium lead halide iodide in hole conductor free perovskite-based solar cells

Perovskite is a promising light harvester for use in photovoltaic solar cells. In recent years, the power conversion efficiency of perovskite solar cells has been dramatically increased, making them a competitive source of renewable energy. An important parameter when designing high efficiency perovskite-based solar cells is the perovskite deposition, which must be performed to create complete coverage and optimal film thickness. This paper describes an in-depth study on two-step deposition, separating the perovskite deposition into two precursors. The effects of spin velocity, annealing temperature, dipping time, and methylammonium iodide concentration on the photovoltaic performance are studied. Observations include that current density is affected by changing the spin velocity, while the fill factor changes mainly due to the dipping time and methylammonium iodide concentration. Interestingly, the open circuit voltage is almost unaffected by these parameters. Hole conductor free perovskite solar cells are used in this work, in order to minimize other possible effects. This study provides better understanding and control over the perovskite deposition through highly efficient, low-cost perovskite-based solar cells.

36 MATERIALS SCIENCE↗

Collaborative atomic-scale design, analysis, and nanofabrication for record breaking, single-crystal Zn(x)Cd(1-x)Te solar cell arrays

Cadmium telluride (CdTe) based photovoltaics provide a viable solar energy solution because of their short payback time, low manufacturing cost, and high theoretical efficiency ~29%. However, the highest record laboratory efficiency is only 22.1% and long-term performance degradation is ~1 % per year which hinders greater economic viability. Higher open circuit voltage (Voc) and fill factor (FF) are needed to increase the efficiency of the solar cell. Cells with record energy conversion efficiencies report short current (Jsc) values close to their theoretical maximum. However, Voc and FF in these devices remain well below their anticipated optimum. These electrical parameters depend on the quality of the various layers in the solar cell. In particular they depend on the crystalline quality including the defect and impurity concentrations. Therefore understanding how defects and impurities form and evolve in the material layers is important to design devices with higher efficiency and stability. The aim of this project is to create a novel path around the fundamental barriers to achieve high open-circuit voltages (VOC ≥ 1.0 V) in CdTe/CdS solar cells. The idea of the project was to combine nanopatterned crystal growth and alloy compositional grading (with concomitant lattice parameter and energy band gap grading) to reduce the defect density and dramatically improve spatial uniformity of ZnxCd(1-x)Te/CdS cells. The lattice mismatch between ZnTe and CdS is 3.9% compared to a much larger 9.2% between CdTe and CdS. Importantly, when crystal growth is contained to the nanoscale, the strain in each layer is reduced by a factor of two due to strain partitioning and 3D strain relief mechanisms that come into play. This reduces the strain in the ZnTe from 3.9% to 1.95% which is within the range of metamorphic crystal growth. In preliminary studies, molecular dynamics simulation of ZnTe/CdS islands predicted dislocation-free material when the patterning was reduced to ~80 nm in diameter. The energy band gap of ZnxCd(1-x)Te is also graded in conjunction with alloy composition. ZnTe has an energy band gap of 2.3 eV. Finally, an added benefit of patterned growth is that it enables direct one-to-one study of the relationships between fabrication, microstructure and performance of individual crystal grains within the array. Experimental characterization techniques such as atomic probe tomography (APT) and transmission electron microscopy (TEM) have elucidated much about the microstructure of the layers. However, the techniques are destructive, costly and have limitations on the information they convey. For example, TEM gives information with atomic scale resolution but on 2-dimensional substrates. On the other hand, APT gives 3-dimensional information but is not able to resolve atomic scale structure. Alternatively, Molecular Dynamics (MD) simulations offer a solution to rapidly generate time-resolved, 3-dimensional, atomic scale structures of crystal growth. Direct MD simulations of microstructures of Cu-doped II-VI compound multilayers can impact the research on CdTe/CdS solar cells. Such MD simulations require an interatomic potential database that includes at least four elements Cu, Cd, Te, and S. The Stillinger-Weber (SW) potential is the most widely used interatomic potential for semiconductors. However, while SW potentials have been developed for Ga-In-As-Se-Te, Al-Ga-In-P-As-Sb, Cd-Te-Zn-As-Si, In-Ga-N systems, no potentials existed to simulate Cd-Zn-Hg-Se-S-Te-Cu. The goal of this effort was to fill the knowledge gap by developing a Zn-Cd-Hg-S-Se-Te-Cu SW potential database to enable MD simulations of microstructures of Cu-doped CdTe/CdS solar cells. The new potential was then applied, via MD crystal growth simulations, to study the growth mechanisms and atomic structures of the ZnTe/Cu/CdTe/CdS multilayers under various conditions. The objective of the project was to inform the solar cell community on crystal growth and defect formation at the interface between CdTe-based epilayers grown on CdS substrates. MD simulations offered a unique opportunity to analyze the 3-dimensional crystal growth evolution of Cu doped ZnxCd(1-x)TeyS(1-y) alloys with atomic scale resolution under a variety of conditions. The effect of substrate orientation and polycrystallinity on crystal growth was studied. Substrates with grain boundaries were created and the growth evolution on these substrates were analyzed. Another focus was to elucidate the effect of dopant incorporation on the nature of polycrystallinity crystal growth. Dopants available through the Stillinger-Weber potential developed in this project included Cu, Zn, S, Se, Hg and native vacancies.

14 SOLAR ENERGY↗

Morphology control of ZnO nanostructures for high efficient dye-sensitized solar cells

Dye-sensitized solar cells (DSSCs) were fabricated based on different ZnO nanostructures with controllable morphologies synthesized via capping agent-assisted hydrothermal method. The capping agent hindered the growth along (001) direction, so the morphology evolved from rods to nanosheets with increasing the amounts of capping agents. The kinetics of the photoelectrochemical properties in DSSCs were also evaluated via electrochemical impedance spectroscopy with focusing on exploring the electron lifetime, electron diffusion coefficient and effective diffusion length of the cells in a quantitative manner based on an equivalent circuit model. The physical properties, such as specific surface area, photoluminescence and ultraviolet–vis diffuse reflectance spectra (DRS), were also extensively characterized in detail. DSSCs fabricated with ZnO nanosheets/rod hierarchical structures as photoanodes showed significantly improved photovoltaic performance with open-circuit voltage increasing from 0.45 V to 0.73 V, as well as the overall conversion efficiency 5.69 times better than that of ZnO rod. It was attributed to higher surface area (21.96 m{sup 2}·g{sup −1}) and more efficient light absorption, as well as more efficient electron transfer process. - Highlights: • Controlled morphologies from rods to nanosheets were manipulated by hydrothermal method. • Different ZnO morphologies based DSSCs were investigated by IV and EIS with forward biases. • DSSCs based on nano hierarchical structures yield 5.67 times higher of power conversion efficiency than that of rods.

36 MATERIALS SCIENCE↗

Evaluation of transition metal oxide as carrier-selective contacts for silicon heterojunction solar cells

"Reducing light absorption in the non-active solar cell layers, while enabling the extraction of the photogenerated minority carriers at quasi-Fermi levels are two key factors to improve current generation and voltage, and therefore efficiency of silicon heterojunction solar devices. To address these two critical aspects, transition metal oxide materials have been proposed as alternative to the n- and p-type amorphous silicon used as electron and hole selective contacts, respectively. Indeed, transition metal oxides such as molybdenum oxide, titanium oxide, nickel oxide or tungsten oxide combine a wide band gap typically over 3 eV with a band structure and theoretical band alignment with silicon that results in high transparency to the solar spectrum and in selectivity for the transport of only one carrier type. Improving carrier extraction or injection using transition metal oxide has been a topic of investigation in the field of organic solar cells and organic LEDs; from these pioneering works a lot of knowledge has been gained on materials properties, ways to control these during synthesis and deposition, and their impact on device performance. Recently, the transfer of some of this knowledge to silicon solar cells and the successful application of some metal oxide to contact heterojunction devices have gained much attention. In this contribution, we investigate the suitability of various transition metal oxide films (molybdenum oxide, titanium oxide, and tungsten oxide) deposited either by thermal evaporation or sputtering as transparent hole or electron selective transport layer for silicon solar cells. In addition to systematically characterize their optical and structural properties, we use photoemission spectroscopy to relate compound stoichiometry to band structure and characterize band alignment to silicon. The direct silicon/metal oxide interface is further analyzed by quasi-steady state photoconductance decay method to assess the quality of surface passivation. In complement, we construct full device structures incorporating in some cases surface passivation schemes, with measured initial conversion efficiency over 15% and evaluate the carrier transport properties using temperature-dependent current-voltage and capacitance-voltage measurements. With this detailed characterization study, we aim at providing the framework to assess the potential of a material as a carrier selective contact and the understanding of how each of the aforementioned parameters on the metal oxide films influence the full solar cell operating performances.

14 SOLAR ENERGY↗

A V-grooved GaAs solar cell

V-grooved GaAs solar cells promise the benefits of improved optical coupling, higher short-circuit current, and increased tolerance to particle radiation compared to planar cells. A GaAs homojunction cell was fabricated by etching a V-groove pattern into an n epilayer (2.1 x 10 to the 17th power per cu cm) grown by metalorganic chemical vapor deposition (MOCVD) on an n+ substrate (2.8 x 10 to the 18th power per cu cm) and then depositing and MOCVD p epilayer (4.2 x 10 to the 18th power per cu cm). Reflectivity measurements on cells with and without an antireflective coating confirm the expected decrease in reluctance of the microgrooved cell compared to the planar structure. The short circuit current of the V-grooved solar cell was 13 percent higher than that of the planar control.

Bailey, S. G.↗

Spectral binning for energy production calculations and multijunction solar cell design

Currently, most solar cells are designed for and evaluated under standard spectra intended to represent typical spectral conditions. However, no single spectrum can capture the spectral variability needed for annual energy production (AEP) calculations, and this shortcoming becomes more significant for series-connected multijunction cells as the number of junctions increases. For this reason, AEP calculations are often performed on very detailed yearlong sets of data, but these pose 2 inherent challenges: (1) These data sets comprise thousands of data points, which appear as a scattered cloud of data when plotted against typical parameters and are hence cumbersome to classify and compare, and (2) large sets of spectra bring with them a corresponding increase in computation or measurement time. Here, we show how a large spectral set can be reduced to just a few 'proxy' spectra, which still retain the spectral variability information needed for AEP design and evaluation. The basic 'spectral binning' methods should be extensible to a variety of multijunction device architectures. In this study, as a demonstration, the AEP of a 4-junction device is computed for both a full set of spectra and a reduced proxy set, and the results show excellent agreement for as few as 3 proxy spectra. This enables much faster (and thereby more detailed) calculations and indoor measurements and provides a manageable way to parameterize a spectral set, essentially creating a 'spectral fingerprint,' which should facilitate the understanding and comparison of different sites.

14 SOLAR ENERGY↗

No Evidence for Passivation Effects of Na and K at Grain Boundaries in Polycrystalline Cu(In,Ga)Se2 Thin Films for Solar Cells

Thin-film solar cells based on Cu(In,Ga)Se2 (CIGSe) absorber layers reach conversion efficiencies of above 20%. One key to this success is the incorporation of alkali metals, such as Na and K, into the surface and the volume of the CIGSe thin film. The present work discusses the impact of Na and K on the grain-boundary (GB) properties in CIGSe thin films, i.e., on the barriers for charge carriers, ..phi..b, and on the recombination velocities at the GBs, sGB. First, the physics connected with these two quantities as well as their impact on the device performance are revised, and then the values for the barrier heights and recombination velocities are provided from the literature. The sGB values are measured by means of a cathodoluminescence analysis of Na-/K-free CIGSe layers as well as on CIGSe layers on Mo/sapphire substrates, which are submitted to only NaF or only KF postdeposition treatments. Overall, passivating effects on GBs by neither Na nor K can be confirmed. The GB recombination velocities seem to remain on the same order of magnitude, in average about 10^3-10^4 cm s^-1, irrespective of whether CIGSe thin films are Na-/K-free or Na-/K-containing.

14 SOLAR ENERGY↗

Cost-Efficiency balanced polymer acceptors based on lowly fused Dithienopyrrolo[3, 2b]benzothiadiazole for 16.04% efficiency All-Polymer solar cells

All-polymer solar cells (All-PSCs) attracted increasing attention due to the outstanding thermal stability and mechanical properties. The current prevailing polymer acceptors for most efficient All-PSCs are polymerized high-performance small molecule acceptor of Y6, i.e. the dithienothiopheno[3,2-b]-pyrrolobenzothiadiazole (BTTP) based polymers. However, the BTTP-based polymers often show relatively shallow highest occupied molecular orbital (HOMO) energy level and high figure of merit (FOM), which limit the rational selection of paring donor polymers. Herein, we presented two low-cost polymer acceptors, namely as BTP-T2F and BTP-2T2F, based on lowly fused dithienopyrrolo[3,2b]benzothiadiazole (BTP, removing two thiophene cycles from BTTP). Here the BTP-based polymers exhibited deeper HOMO levels around –5.90 eV, which could match variable donor polymers with low-lying HOMO levels, such as low-cost PTQ10. Additionally, the synthesis was significantly simplified compared to BTTP-based polymers. A power conversion efficiency (PCE) of 14.32% was achieved in binary blend device containing PTQ10:BTP-2T2F. By adding a miscibility-enhancing PBDTCl-TPD as a third component, the top PCE of 16.04% was obtained in ternary blend All-PSCs. Combining the high device performance and low estimated cost, extraordinary cost-efficiency balance was realized within these BTP-based polymer acceptors.

36 MATERIALS SCIENCE↗

Towards linking lab and field lifetimes of perovskite solar cells

Metal halide perovskite solar cells (PSCs) represent a promising low-cost, thin-film photovoltaic (PV) technology, with unprecedented power conversion efficiencies (PCEs) obtained for both single-junction and tandem applications. To push PSCs toward commercialization, it is critical, albeit challenging, to understand device reliability under real-world outdoor conditions where multiple stress factors (e.g., light, heat, humidity) coexist, generating complicated degradation behaviors. It is necessary to identify accelerated indoor testing protocols - which can correlate specific stressors with observed degradation modes in fielded devices - to quickly guide PSC development. Here, we use a state-of-the-art p-i-n PSC stack (with PCE up to ~25.5%) to show that indoor accelerated stability tests can predict our 6-month outdoor aging tests. Device degradation rates under illumination and at elevated temperatures are most instructive for understanding outdoor device reliability. Further, we also find that the indium tin oxide (ITO)/self-assembled monolayer (SAM)-based hole transport layer (HTL)/perovskite interface most strongly affects our device operation stability. Improving the ion-blocking properties of the SAM HTL increases averaged device operational stability at 50 degree C-85 °C by a factor of ~2.8, reaching over 1000 h at 85 °C and to near 8200 h at 50 °C with a projected 20% degradation, which is among the best to date for high-efficiency p-i-n PSCs.

14 SOLAR ENERGY↗

Improving Miscibility of Polymer Donor and Polymer Acceptor by Reducing Chain Entanglement for Realizing 18.64 % Efficiency All Polymer Solar Cells

All-polymer solar cells have experienced rapid development in recent years by the emergence of polymerized small molecular acceptors (PSMAs). However, the strong chain entanglements of polymer donors (P D s) and polymer acceptors (P A s) decrease the miscibility of the resulting polymer mixtures, making it challenging to optimize the blend morphology. Herein, we designed three P A s, namely PBTPICm-BDD, PBTPICγ-BDD and PBTPICF-BDD, by smartly using a BDD unit as the polymerized unit to copolymerize with different Y-typed non-fullerene small molecular acceptors (NF-SMAs), thus achieving a certain degree of distortion and giving the polymer system enough internal space to reduce the entanglements of the polymer chains. Such effects increase the chances of the P D being interspersed into the acceptor material, which improve the solubility between the P D and P A . The PBTPICγ-BDD and PBTPICF-BDD displayed better miscibility with PBQx-TCl, leading to a well optimized morphology. As a result, high power conversion efficiencies (PCEs) of 17.50 % and 17.17 % were achieved for PBQx-TCl : PBTPICγ-BDD and PBQx-TCl : PBTPICF-BDD devices, respectively. In conclusion, with the addition of PYFT-o as the third component into PBQx-TCl : PBTPICγ-BDD blend to further extend the absorption spectral coverage and finely tune microstructures of the blend morphology, a remarkable PCE of 18.64 % was realized finally.

36 MATERIALS SCIENCE↗