SEARCH · Engineering Papers

Results for “Reacting flows”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57

All sources NASA NTRS DOE OSTI

DOE OSTI2019

Collapse of Reacted Fracture Surface Decreases Permeability and Frictional Strength

Abstract Geochemical and geomechanical perturbations of the subsurface caused by the injection of fluids present risks of leakage and seismicity. This study investigated how acidic fluid flow affects hydraulic and frictional properties of fractures using experiments with 3.8‐cm‐long specimens of Eagle Ford shale, a laminated shale with carbonate‐rich strata. In low‐pressure flow cells, one set of samples was exposed to acidic brine and another set was exposed to neutral brine. X‐ray computed tomography and energy‐dispersive X‐ray spectroscopy revealed that samples exposed to acidic brine were calcite‐depleted and had developed a porous altered layer, while the other set showed no evidence of alteration. After reaction, samples were compressed and sheared in a triaxial cell that supplied normal stress and differential pore pressure at prescribed sliding velocities, independently measuring friction and permeability. During the initial compression, the porous altered layer collapsed into fine particles that filled the fracture. This effectively impeded flow and sealed the fracture, resulting in fracture permeability to decrease 1 to 2 orders of magnitude relative to the unaltered fractures. This is a favorable outcome in subsurface applications where the goal is to reduce leakage risks. However, during shear the reacted fracture had lower frictional strength because the fine‐grained particles in the collapsed layer prevented the formation of interlocking microasperities. Therefore, coupled geochemical and geomechanical processes that could favorably seal fractures could also increase the likelihood of induced seismicity. These findings have important implications for geological carbon sequestration, pressurized fluid energy storage, geothermal energy, and other subsurface technologies.

58 GEOSCIENCES↗

NASA NTRS2009

Frozen Chemistry Effects on Nozzle Performance Simulations

Simulations of exhaust nozzle flows are typically conducted assuming the gas is calorically perfect, and typically modeled as air. However the gas inside a real nozzle is generally composed of combustion products whose thermodynamic properties may differ. In this study, the effect of gas model assumption on exhaust nozzle simulations is examined. The three methods considered model the nozzle exhaust gas as calorically perfect air, a calorically perfect exhaust gas mixture, and a frozen exhaust gas mixture. In the latter case the individual non-reacting species are tracked and modeled as a gas which is only thermally perfect. Performance parameters such as mass flow rate, gross thrust, and thrust coefficient are compared as are mean flow and turbulence profiles in the jet plume region. Nozzles which operate at low temperatures or have low subsonic exit Mach numbers experience relatively minor temperature variations inside the nozzle, and may be modeled as a calorically perfect gas. In those which operate at the opposite extreme conditions, variations in the thermodynamic properties can lead to different expansion behavior within the nozzle. Modeling these cases as a perfect exhaust gas flow rather than air captures much of the flow features of the frozen chemistry simulations. Use of the exhaust gas reduces the nozzle mass flow rate, but has little effect on the gross thrust. When reporting nozzle thrust coefficient results, however, it is important to use the appropriate gas model assumptions to compute the ideal exit velocity. Otherwise the values obtained may be an overly optimistic estimate of nozzle performance.

Yoder, Dennis A.↗

NASA NTRS1988

Direct simulation of three-dimensional flow about the AFE vehicle at high altitudes

Three-dimensional hypersonic rarefied flow about the Aeroassist Flight Experiment (AFE) vehicle was studied using the direct simulation Monte Carlo (DSMC) technique. Results are presented for the transitional flow regime encountered between 120 and 200 km altitudes with a reentry velocity of 9.92 km/s. In the simulations, a five-species reacting real-gas model that accounts for internal energies (rotational and vibrational) is used. The results indicate that the transitional effects are significant even at an altitude of 200 km and influence the overall vehicle aerodynamics. For the cases considered, the aerodynamic coefficients, surface pressures, convective heating, and flow field structure variations with rarefaction effects are presented.

Celenligil, M. Cevdet↗

NASA NTRS1989

Direct simulation of three-dimensional flow about the AFE vehicle at high altitudes

Celenligil, M. Cevdet↗

NASA NTRS1982

Conversion of acoustic energy by lossless liners

The Blokhintzev acoustic energy equation is applied to a two-dimensional duct containing a uniform flow with a finite length lining. It is shown that the difference of the incident and outgoing acoustic energy differs in general from the energy dissipated in the liner, the difference being related to the displacements at the liner's edges. It is shown that in the case of a locally reacting lossless liner for frequencies below the first cut-off frequency and for low Mach number acoustic energy is generated if the flow and the incident sound wave are in the same direction and is absorbed if these two directions are opposite unless special edge conditions are met. Furthermore it is shown under the same conditions that the ratio of the reflection coefficient at finite flow velocity to the reflection coefficient at vanishing velocity is to first order in Mach number independent of the liner characteristics. A numerical calculation confirms these predictions at least for mass-like linear admittance.

Moehring, W.↗

NASA NTRS1990

TiCl4 as a source of TiO2 particles for laser anemometry measurements in hot gas

A method of reacting TiCl4 with water saturated gaseous nitrogen (GN2) at the entrance into a high temperature gas flow is described. The TiO2 particles formed are then entrained in the gas flow and used as seed particles for making laser anemometry (LA) measurements of the flow velocity distribution in the hot gas. Scanning electron microscope photographs of the TiO2 particles are shown. Data rate of the LA processor was measured to determine the amount of TiO2 formed. The TiCl4 and mixing gas flow diagram is shown. This work was performed in an open jet burner.

Weikle, Donald H.↗

NASA NTRS1994

On the Dynamics of Computing a Chemically Relaxed Nonequilibrium Flow

In order to gain insights into the strong dependence of numerical solutions on initial data for finite time steps, a set of nonlinear test problems rich enough to capture the behavior of difference schemes were recently identified and the numerical basins of attraction for these problems were computed using commonly used time discretizations in CFD. Our study revealed a wealth of surprisingly nonlinear behavior of numerical schemes that were not observed before, in particular for the implicit time discretizations that are commonly used in CFD. The goal of this work is to apply these tools to study a practical model from non-equilibrium flowfield relaxation. This type of problem arises in chemically nonequilibrium hypersonic flows such as in a shock tube experiment or an expanding nozzle. Here we consider a reacting mixture of (N2, N) for an inviscid one-dimensional steady model. Preliminary numerical results indicate that, aside from the possibility of spurious numerical solutions being introduced by the time discretizations, limitations on the model for physical or accurate solutions may also play a part in the dynamics observed.

Sweby, P. K.↗

NASA NTRS1996

Lubricous Deposit Formed In Situ Between Wearing Surfaces at High Temperatures

Many components of future aircraft will be constructed from novel high-temperature materials, such as superalloys and ceramic composites, to meet expected operating temperatures in excess of 300 C. There are no known liquid lubricants that can lubricate above 300 C without significant decomposition. Solid lubricants could be considered, but problems caused by the higher friction coefficients and wear rates of the solid lubricant film make this an undesirable approach. An alternative method of lubrication is currently being investigated: vapor phase lubrication. In vapor phase lubrication, an organic liquid (in our studies a thioether was used) is vaporized into a flowing air stream that is directed to sliding surfaces where lubrication is needed. The organic vapor reacts at the concentrated contact sliding area generating a lubricous deposit. This deposit has been characterized as a thin polymeric film that can provide effective lubrication at temperatures greater than 400 C. Initial tribological studies were conducted at the NASA Lewis Research Center and Cleveland State University with a high-temperature friction and wear tribometer. A cast iron rod was loaded (a 4-kg mass was used to generate a contact pressure of 1.2 MPa) against a reciprocating, cast iron plate at 500 C. This system was then lubricated with the vapor phase of thioether.

Source record↗

NASA NTRS2001

Numerical Simulation of an Enclosed Laminar Jet Diffusion Flame in Microgravity Environment: Comparison with ELF Data

Enclosed diffusion flames are commonly found in practical combustion systems, such as the power-plant combustor, gas turbine combustor, and jet engine after-burner. In these systems, fuel is injected into a duct with a co-flowing or cross-flowing air stream. The diffusion flame is found at the surface where the fuel jet and oxygen meet, react, and consume each other. In combustors, this flame is anchored at the burner (i.e., fuel jet inlet) unless adverse conditions cause the flame to lift off or blow out. Investigations of burner stability study the lift off, reattachment, and blow out of the flame. Flame stability is strongly dependent on the fuel jet velocity. When the fuel jet velocity is sufficiently low, the diffusion flame anchors at the burner rim. When the fuel jet velocity is increased, the flame base gradually moves downstream. However, when the fuel jet velocity increases beyond a critical value, the flame base abruptly jumps downstream. When this "jump" occurs, the flame is said to have reached its lift-off condition and the critical fuel jet velocity is called the lift-off velocity. While lifted, the flame is not attached to the burner and it appears to float in mid-air. Flow conditions are such that the flame cannot be maintained at the burner rim despite the presence of both fuel and oxygen. When the fuel jet velocity is further increased, the flame will eventually extinguish at its blowout condition. In contrast, if the fuel jet velocity of a lifted flame is reduced, the flame base moves upstream and abruptly returns to anchor at the burner rim. The fuel jet velocity at reattachment can be much lower than that at lift off, illustrating the hysteresis effect present in flame stability. Although there have been numerous studies of flame stability, the controlling mechanisms are not well understood. This uncertainty is described by Pitts in his review of various competing theories of lift off and blow out in turbulent jet diffusion flames. There has been some research on the stability of laminar flames, but most studies have focused on turbulent flames. It is also well known that the airflow around the fuel jet can significantly alter the lift off, reattachment and blow out of the jet diffusion flame. Buoyant convection is sufficiently strong in 1-g flames that it can dominate the flow-field, even at the burner rim. In normal-gravity testing, it is very difficult to delineate the effects of the forced airflow from those of the buoyancy-induced flow. Comparison of normal-gravity and microgravity flames provides clear indication of the influence of forced and buoyant flows on the flame stability. The overall goal of the Enclosed Laminar Flames (ELF) investigation (STS-87/USMP-4 Space Shuttle mission, November to December 1997) is to improve our understanding of the effects of buoyant convection on the structure and stability of co-flow diffusion flame, e.g., see http://zeta.lerc.nasa.gov/expr/elf.htm. The ELF hardware meets the experiment hardware limit of the 35-liter interior volume of the glovebox working area, and the 180x220-mm dimensions of the main door. The ELF experiment module is a miniature, fan-driven wind tunnel, equipped with a gas supply system. A 1.5-mm diameter nozzle is located on the duct's flow axis. The cross section of the duct is nominally a 76-mm square with rounded corners. The forced air velocity can be varied from about 0.2 to 0.9 m/s. The fuel flow can be set as high as 3 std. cubic centimeter (cc) per second, which corresponds to a nozzle exit velocity of up to 1.70 m/s. The ELF hardware and experimental procedure are discussed in detail in Brooker et al. The 1-g test results are repeated in several experiments following the STS-87 Mission. The ELF study is also relevant to practical systems because the momentum-dominated behavior of turbulent flames can be achieved in laminar flames in microgravity. The specific objectives of this paper are to evaluate the use reduced model for simulation of flame lift-off and blowout.

Jia, Kezhong↗

NASA NTRS1991

Mixing and mixing enhancement in supersonic reacting flowfields

Propulsion systems planned for use late in this century and beyond will require appropriate physical models for describing supersonic combustion and numerical techniques for solving the model governing equations. A computer program to study these flows is reported which considers the multicomponent diffusion and convection of important chemical species, the finite-rate reaction of these species, and the resulting interaction of the field mechanics and the chemistry. The application of the program to a spatially developing and reacting mixing layer, which serves an an excellent physical model for the mixing and reaction processes that take place in a scramjet combustor, is reported. Several techniques to enhance the fuel-air mixing and growth of that layer and improve its overall combustion efficiency are considered.

Drummond, J. P.↗

DOE OSTI2022

Effects of flow on uranium speciation in soils impacted by acidic waste fluids

Radioactive acidic liquid waste is a common byproduct of uranium (U) and plutonium (Pu) enrichment and recycling processes whose accidental and planned release has led to a significant input of U into soils and sediments across the world, including at the U.S. DOE's Hanford site (WA, USA). Because of the particularly hazardous nature of U, it is important to predict its speciation when introduced into soils and sediments by acidic waste fluids. Of fundamental importance are the coupled effects of acid-driven mineral transformation and reactive transport on U speciation. To evaluate the effect of waste-fluid residence time and co-associated dissolved phosphate concentrations on U speciation in impacted soils and sediments, uncontaminated surface materials (from the Hanford Site) were reacted with U-containing synthetic acidic waste fluids (pH 2) amended with dissolved phosphate concentrations in both batch (no flow) and flow-through column systems for 7–365 days. By comparing dissolved U behavior and solid phase speciation as a function of flow regimen, we found that the availability of proton-promoted dissolution products (such as Si) to sequester U into uranyl silicates was dependent on waste fluid-sediment contact time as uranyl silicates were not detected in short contact time flow-through systems but were detected in no-flow, long contact time, reactors. Moreover, the dominance of uranyl phosphate as neoprecipitate U scavenger (principally in the form of meta-ankoleite) in phosphate amended systems confirmed the importance of phosphate amendments for an efficient sequestration of U in the soils and sediments. Overall, our experiments suggest that the formation of uranyl silicates in soils impacted by acidic waste fluids is likely to be limited unless reaction products are allowed to accumulate in soil pores, highlighting the importance of investigating soil U speciation in flow-through, transport-driven systems as opposed to no-flow, batch systems. Finally, this study provides insights into uranium speciation and its potential changes under acidic conditions for better prediction of risks and subsequent development of efficient remediation strategies.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2022

Evaluation of thermodynamic closure models for partially reacted two-phase mixture of condensed phase explosives

One of the key fundamental issues that is crucial in the continuum modeling of reactive flow phenomena is the thermodynamically consistent description of reaction mixture properties. To define the mixture properties, thermodynamic closure rules that relate the properties of the individual reaction components to the mixture properties are required. In the context of reactive two-phase modeling approaches, various strategies to define the thermodynamic closures have been adopted such as pressure temperature (PT) equilibrium between the individual reaction components, pressure (specific) volume (PV) equilibrium, etc. The choice of closure rules determines the relative distribution of specific volume and energy across the reaction components that comprise the mixture. Therefore, depending on the choice of the closure, the mixture thermodynamic behavior can vary. The present work examines the effect of different closure approaches on the thermodynamic properties of the reaction mixture. The analysis is performed for a condensed phase HMX (octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine) based plastic bonded explosive (PBX) 9501 explosive using four different thermodynamic closures, viz., PT equilibrium, PV equilibrium, volume temperature (VT) equilibrium, and pressure (P) equilibrium with reactants on an isentrope. Furthermore, the relative variations in the thermodynamic properties of the mixture are analyzed and compared under both compression and expansion loading regimes. It is shown that out of the four closure models, only PT equilibrium and P equilibrium closures lead to a thermodynamically accurate description of the mixture under both compression and expansion.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

NASA NTRS2011

Combustion Model of Supersonic Rocket Exhausts in an Entrained Flow Enclosure

This paper describes the Computation Fluid Dynamics (CFD) model developed to simulate the supersonic rocket exhaust in an entrained flow cylinder. The model can be used to study the plume-induced environment due to static firing test of the Taurus II launch vehicle. The finite rate chemistry is used to model the combustion process involving rocket propellant (RP 1) and liquid oxidizer (LOX). A similar chemical reacting model is also used to simulate the mixing of rocket plume and ambient air. The model provides detailed information on the gas concentration and other flow parameters within the enclosed region thus allowing different operating scenarios to be examined in an efficient manner. It is shown that the real gas influence is significant and yields better agreement with the theory.

Vu, Bruce↗

NASA NTRS2008

Mixing of Multiple Jets with a Confined Subsonic Crossflow: Part III--The Effects of Air Preheat and Number of Orifices on Flow and Emissions in an RQL Mixing Section

This study was motivated by a goal to understand the mixing and emissions in the Rich-burn/Quick-mix/Lean-burn (RQL) combustor scheme that has been proposed to minimize the formation of oxides of nitrogen (NOx) in gas turbine combustors. The study reported herein was a reacting jet-in-crossflow experiment at atmospheric pressure. The jets were injected from the perimeter of a cylindrical duct through round-hole orifices into a fuel-rich mainstream flow. The number of orifices investigated in this study gave over- to optimum to underpenetrating jets at a jet-to-mainstream momentum-flux ratio of J = 57. The size of individual orifices was decreased as the number of orifices increased to maintain a constant total area; the jet-to-mainstream mass-flow ratio was constant at MR = 2.5. The experiments focused on the effects of the number of orifices and inlet air preheat and were conducted in a facility that provided the capability for independent variation of jet and main inlet air preheat temperature. The number of orifices was found to have a significant effect on mixing and the distributions of species, but very little effect on overall NOx emissions, suggesting that an aerodynamically optimum mixer might not minimize NOx emissions. Air preheat was found to have very little effect on mixing and the distributions of major species, but preheating both main and jet air did increase NOx emissions significantly. Although the air jets injected in the quick-mix section of an RQL combustor may comprise over 70 percent of the total air flow, the overall NOx emission levels were found to be more sensitive to main stream air preheat than to jet stream air preheat.

Holdemann, James D.↗

NASA NTRS1974

Absorption characteristics of glass fiber materials at normal and oblique incidence

The absorption characteristics of several fibrous materials of the Owens Corning 700 Fiberglas Series were measured to determine the variation in impedance as a function of incident angle of the sound wave. The results, indicate that the fibrous absorbents behave as extended reacting materials. The poor agreement between measurement and theory for sound absorption based on the parameters of flow resistance and porosity indicates that this theory does not adequately predict the acoustic behavior of fibrous materials. A much better agreement with measured results is obtained for values calculated from the bulk acoustic parameters of the material.

Wyerman, B. R.↗

NASA NTRS1976

Prediction of the acoustic impedance of duct liners

Recent research which contributes to the prediction of the acoustic impedance of duct liners is reviewed. This review includes the linear and nonlinear properties of sheet and bulk type materials and methods for the measurement of these properties. It also includes the effect of grazing flow on the acoustic properties of materials. Methods for predicting the properties of single or multilayered, point reacting or extended reaction, and flat or curved liners are discussed. Based on this review, methods for predicting the properties of the duct liners which are typically used in aircraft engines are recommended. Some areas of needed research are discussed briefly.

Zorumski, W. E.↗

NASA NTRS1977

An experimental study of reactive turbulent mixing

An experimental study of the turbulent mixing of two coaxial gas streams, which react very rapidly (pseudo-hypergolic chemical kinetics), was performed to investigate the mixing characteristics of turbulent flow fields. The center stream consisted of a CO-N2 mixture and the outer annular stream consisted of air vitiated by H2 combustion. The streams were at equal velocity (50 m/sec) and temperature (1280 K). Turbulence measurements were obtained using hot film anemometry. A sampling probe was used to obtain time averaged gas compositions. Six different turbulence generators were placed in the annular passage to alter the flow field mixing characteristics. The turbulence generators affected the bulk mixing of the streams and the extent of CO conversion to different degrees. The effects can be related to the average eddy size and the bulk mixing. Higher extents of conversion of CO to CO2 were found by increasing the bulk mixing and decreasing the average eddy size.

Cooper, L. P.↗

NASA NTRS1983

Relative rate constants for the reactions of atomic oxygen with HO2 anad OH radicals

Relative rate constants for the reactions O + HO2 - OH + O2 (1) and O + OH - H + O2 (2) were obtained by using the discharge-flow resonance fluorescence technique at 2 torr total pressure and 299 K. HO2 radicals were generated by reacting atomic hydrogen with an excess of O2. Quasi-steady-state concentrations of OH and HO2 were established in the presence of excess atomic oxygen. Observed concentration ratios, namely the ratio of the OH concentration to the HO2 concentration, resulted in a value of 1.7 + or 0.2 for k1/k2. The error limits are twice the standard deviation obtained from the data analysis. Overall experimental error is estimated to be + or - 25 percent. This result confirms earlier direct measurements of k1 and k2 which required knowledge of absolute radical or atomic oxygen concentrations.

Keyser, L. F.↗