Microstructural characterization of a thin film ZrN diffusion barrier in an As-fabricated U–7Mo/Al matrix dispersion fuel plate
Not Available
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Not Available
This paper describes new research being performed to improve understanding of seismic waves generated by underground nuclear explosions (UNE) by using full waveform simulation, high-performance computing and three-dimensional (3D) earth models. The goal of this effort is to develop an end-to-end modeling capability to cover the range of wave propagation required for nuclear explosion monitoring (NEM) from the buried nuclear device to the seismic sensor. The goal of this work is to improve understanding of the physical basis and prediction capabilities of seismic observables for NEM including source and path-propagation effects. We are pursuing research along three main thrusts. Firstly, we are modeling the non-linear hydrodynamic response of geologic materials to underground explosions in order to better understand how source emplacement conditions impact the seismic waves that emerge from the source region and are ultimately observed hundreds or thousands of kilometers away. Empirical evidence shows that the amplitudes and frequency content of seismic waves at all distances are strongly impacted by the physical properties of the source region (e.g. density, strength, porosity). To model the near-source shock-wave motions of an UNE, we use GEODYN, an Eulerian Godunov (finite volume) code incorporating thermodynamically consistent non-linear constitutive relations, including cavity formation, yielding, porous compaction, tensile failure, bulking and damage. In order to propagate motions to seismic distances we are developing a one-way coupling method to pass motions to WPP (a Cartesian anelastic finite difference code). Preliminary investigations of UNE's in canonical materials (granite, tuff and alluvium) confirm that emplacement conditions have a strong effect on seismic amplitudes and the generation of shear waves. Specifically, we find that motions from an explosion in high-strength, low-porosity granite have high compressional wave amplitudes and weak shear waves, while an explosion in low strength, high-porosity alluvium results in much weaker compressional waves and low-frequency compressional and shear waves of nearly equal amplitude. Further work will attempt to model available near-field seismic data from explosions conducted at NTS, where we have accurate characterization of the sub-surface from the wealth of geological and geophysical data from the former nuclear test program. Secondly, we are modeling seismic wave propagation with free-surface topography in WPP. We have model the October 9, 2006 and May 25, 2009 North Korean nuclear tests to investigate the impact of rugged topography on seismic waves. Preliminary results indicate that the topographic relief causes complexity in the direct P-waves that leads to azimuthally dependent behavior and the topographic gradient to the northeast, east and southeast of the presumed test locations generate stronger shear-waves, although each test gives a different pattern. Thirdly, we are modeling intermediate period motions (10-50 seconds) from earthquakes and explosions at regional distances. For these simulations we run SPECFEM3D{_}GLOBE (a spherical geometry spectral element code). We modeled broadband waveforms from well-characterized and well-observed events in the Middle East and central Asia, as well as the North Korean nuclear tests. For the recent North Korean test we found that the one-dimensional iasp91 model predicts the observed waveforms quite well in the band 20-50 seconds, while waveform fits for available 3D earth models are generally poor, with some exceptions. Interestingly 3D models can predict energy on the transverse component for an isotropic source presumably due to surface wave mode conversion and/or multipathing.
Through a U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL) funded cooperative agreement DE-NT0005649, ADA Environmental Solutions (ADA) has begun evaluating the use of solid sorbents for CO{sub 2} capture. The project objective was to address the viability and accelerate development of a solid-based CO{sub 2} capture technology. To meet this objective, initial evaluations of sorbents and the process/equipment were completed. First the sorbents were evaluated using a temperature swing adsorption process at the laboratory scale in a fixed-bed apparatus. A slipstream reactor designed to treat flue gas produced by coal-fired generation of nominally 1 kWe was designed and constructed, which was used to evaluate the most promising materials on a more meaningful scale using actual flue gas. In a concurrent effort, commercial-scale processes and equipment options were also evaluated for their applicability to sorbent-based CO{sub 2} capture. A cost analysis was completed that can be used to direct future technology development efforts. ADA completed an extensive sorbent screening program funded primarily through this project, DOE NETL cooperative agreement DE-NT0005649, with support from the Electric Power Research Institute (EPRI) and other industry participants. Laboratory screening tests were completed on simulated and actual flue gas using simulated flue gas and an automated fixed bed system. The following types and quantities of sorbents were evaluated: 87 supported amines; 31 carbon based materials; 6 zeolites; 7 supported carbonates (evaluated under separate funding); and 10 hydrotalcites. Sorbent evaluations were conducted to characterize materials and down-select promising candidates for further testing at the slipstream scale. More than half of the materials evaluated during this program were supported amines. Based on the laboratory screening four supported amine sorbents were selected for evaluation at the 1 kW scale at two different field sites. ADA designed and fabricated a slipstream pilot to allow an evaluation of the kinetic behavior of sorbents and provide some flexibility for the physical characteristics of the materials. The design incorporated a transport reactor for the adsorber (co-current reactor) and a fluidized-bed in the regenerator. This combination achieved the sorbent characterization goals and provided an opportunity to evaluate whether the potential cost savings associated with a relatively simple process design could overcome the sacrifices inherent in a co-current separation process. The system was installed at two field sites during the project, Luminant's Martin Lake Steam Electric Station and Xcel Energy's Sherburne County Generating Station (Sherco). Although the system could not maintain continuous 90% CO{sub 2} removal with the sorbents evaluated under this program, it was useful to compare the CO{sub 2} removal properties of several different sorbents on actual flue gas. One of the supported amine materials, sorbent R, was evaluated at both Martin Lake and Sherco. The 1 kWe pilot was operated in continuous mode as well as batch mode. In continuous mode, the sorbent performance could not overcome the limitations of the cocurrent adsorbent design. In batch mode, sorbent R was able to remove up to 90% CO{sub 2} for several cycles. Approximately 50% of the total removal occurred in the first three feet of the adsorption reactor, which was a transport reactor. During continuous testing at Sherco, CO{sub 2} removal decreased to approximately 20% at steady state. The lack of continuous removal was due primarily to the combination of a co-current adsorption system with a fluidized bed for regeneration, a combination which did not provide an adequate driving force to maintain an acceptable working CO{sub 2} capacity. In addition, because sorbent R consisted of a polymeric amine coated on a silica substrate, it was believed that the 50% amine loaded resulted in mass diffusion limitations related to the CO{sub 2} uptake rate. Three additional supported amine materials, sorbents AX, F, and BN, were selected for evaluation using the 1 kW pilot at Sherco. Sorbent AX was operated in batch mode and performed similarly to sorbent R (i.e. could achieve up to 90% removal when given adequate regeneration time). Sorbent BN was not expected to be subject to the same mass diffusion limitations as experienced with sorbent R. When sorbent BN was used in continuous mode the steady state CO{sub 2} removal was approximately double that of sorbent R, which highlighted the importance of sorbents without kinetic limitations.
Since 2012, the U.S. Department of Energy’s X-Stack program has been developing solutions including runtime systems, programming models, languages, compilers, and tools for the Exascale system software to address crucial performance and power requirements. Fine grain programming models and runtime systems show a great potential to efficiently utilize the underlying hardware. Thus, they are essential to many X-Stack efforts. An abundant amount of small tasks can better utilize the vast parallelism available on current and future machines. Moreover, finer tasks can recover faster and adapt better, due to a decrease in state and control. Nevertheless, current applications have been written to exploit old paradigms (such as Communicating Sequential Processor and Bulk Synchronous Parallel processing). To fully utilize the advantages of these new systems, applications need to be adapted to these new paradigms. As part of the applications’ porting process, in-depth characterization studies, focused on both application characteristics and runtime features, need to take place to fully understand the application performance bottlenecks and how to resolve them. This paper presents a characterization study for a novel high performance runtime system, called the Open Community Runtime, using key HPC kernels as its vehicle. This study has the following contributions: one of the first high performance, fine grain, distributed memory runtime system implementing the OCR standard (version 0.99a); and a characterization study of key HPC kernels in terms of runtime primitives running on both intra and inter node environments. Running on a general purpose cluster, we have found up to 1635x relative speed-up for a parallel tiled Cholesky Kernels on 128 nodes with 16 cores each and a 1864x relative speed-up for a parallel tiled Smith-Waterman kernel on 128 nodes with 30 cores.
Despite the availability of interdisciplinary academic training programs, the practice of environmental science is often hampered by a lack of convergence across diverse disciplines. This gap is particularly salient in settings characterized by complex environmental issues, such as multiple-use coastal ecosystems. In response, we developed and implemented a training, research, and communication framework to provide undergraduates with an authentic operative experience working at the interface of interdisciplinary science and public decision-making within a case study of marine renewable energy. In our program, students gained hands-on experience with the scientific process and learned how to make information relevant, useful, and accessible to diverse stakeholder groups. Application of this framework demonstrates that the process of integrating data from biological (visual and acoustic monitoring of fish and marine mammals), physical (hydrodynamics), and social (local ecological knowledge) sciences can provide a more complete understanding of complex and turbulent ecosystems for better informed decision-making. We offer several recommendations to facilitate the adaptation and implementation of our interdisciplinary framework to diverse research contexts, with a focus on interdisciplinary training for the next generation of marine scientists.
The Al Tuwaitha nuclear complex near Baghdad contains a number of facilities from Saddam Hussan's nuclear weapons program. Past military operations, lack of upkeep and looting have created an enormous radioactive waste problem at the Al Tuwaitha complex, which contains various, uncharacterized radioactive wastes, yellow cake, sealed radioactive sources, and contaminated metals that must be constantly guarded. Iraq has never had a radioactive waste disposal facility and the lack of a disposal facility means that ever increasing quantities of radioactive material must be held in guarded storage. The Iraq Nuclear Facility Dismantlement and Disposal Program (the NDs Program) has been initiated by the U.S. Department of State (DOS) to assist the Government of Iraq (GOI) in eliminating the threats from poorly controlled radioactive materials, while building human capacities so that the GOI can manage other environmental cleanups in their country. The DOS is funding the IAEA to provide technical assistance via Technical Cooperation projects. Program coordination will be provided by the DOS, consistent with GOI policies, and Sandia National Laboratories will be responsible for coordination of participants and waste management support. Texas Tech University will continue to provide in-country assistance, including radioactive waste characterization and the stand-up of the Iraq Nuclear Services Company. The GOI owns the problems in Iraq and will be responsible for implementation of the NDs Program.
This report is submitted as completion of a Milestone 3 deliverable under work package ORNL CT-23OR1304051 in support of the Advanced Materials and Manufacturing Technologies (AMMT) program. The AMMT program is aiming at the faster incorporation of new materials and manufacturing technologies into complex nuclear-related systems. An integrated approach, combining advanced characterization, high-throughput and accelerated testing, modeling and simulation including machine learning and artificial intelligence will be employed. While 316H (Fe-16-18Cr-10-14Ni-2-3Mo-0.04-0.1C) has been identified as a key alloy to be integrated into the AMMT accelerated alloy qualification approach due its relevance for many current and future nuclear energy reactors, many other alloys could be considered for the advanced fabrication of innovate high-performance nuclear components. ANL, INL, ORNL and PNNL are collaborating on identifying the most promising alloy candidates relevant for the AMMT program. A selection criteria matrix was established to evaluate the alloys considering their relative importance and technological readiness levels for nuclear energy applications, with a focus on laser powder bed fusion (LPBF). Due to the broad range of potential candidate alloys, ORNL and INL focused on Ni-based alloys, while ANL and PNNL mainly evaluated Fe-based alloys. PNNL previously published materials scorecards reports on several key alloys and this report is providing a broader overview of Ni-based candidate alloys, expending beyond alloys well-known to the nuclear community. Of particular interest are alloys that are currently commercially available in powder form due to the growing demand from other industries that have invested heavily in additive manufacturing. Among these alloys, Haynes 282 (Fe-20Cr-20Co-8Mo) was selected due to its superior strength at high temperature compared to the code-qualified alloy 617 (Ni-20-24Cr-10-15Co-8-10Mo). To assess the integration of this new alloy into the AMMT digital manufacturing framework, we performed the rapid optimization of alloy 282 printing parameters on a Renishaw 250 machine, the fabrication of sufficient materials for extensive characterization and mechanical testing both at ORNL and INL, and added the printing data into the digital platform via the Peregrine software. A detailed analysis of the LPBF 718 alloy was also conducted, with creep specimens being tested at 600-650°C and characterized by advanced electron microscopy. The alloy superior mechanical strength and great printability associated with the extensive database that has already been generated highlight the promising potential of LPBF 718 as a candidate alloy for the AMMT program. INL, ANL and PNNL have generated similar reports and all the information will be compiled into a final M2 milestone report to provide the AMMT leadership team with clear recommendations on the down selection of reactor materials, as well as establish a roadmap for the qualification of these selected alloys.
The “Development of High Pressure Hydrogen Storage Tanks for Storage and Gaseous Truck Delivery” project [DE-FG36-08GO18062] was initiated on 01 July 2008. Hexagon Lincoln (then Lincoln Composites) received grant funding from the U.S. Department of Energy to support the design and development of an improved bulk hauling and storage solution for hydrogen in terms of cost, safety, weight and volumetric efficiency. The development of this capability required parallel development and qualification of large all-composites pressure vessels, a custom ISO container to transport and store said tanks, and performance of trade studies to identify optimal operating pressure for the system. Qualification of the 250 bar TITAN® module was completed in 2009 with supervision from the American Bureau of Shipping [ABS], and the equipment has been used internationally for bulk transportation of fuel gases since 2010. Phase 1 of the project was successfully completed in 2012 with the issuance of USDOT SP 14951, the special permit authorizing the manufacture, marking, sale and use of TITAN® Mobile Pipeline® equipment in the United States. The introduction of tube trailers with light weight composite tankage has meant that 2 to 3 times as much gaseous fuel can be transported with each trip. This increased hauling efficiency offers dramatically reduced operating costs and has enabled a profitable business model for over-the-road compressed natural gas delivery. The economic drivers of this business opportunity vary from country to country and region to region, but in many places gas distribution companies have realized profitable operations. Additional testing was performed in 2015 to characterize hydrogen-specific operating protocols for use of TITAN® systems in CHG service at 250 bar. This program demonstrated that existing compression and decompression methodologies can efficiently and safely fill and unload lightweight bulk hauling systems. Hexagon Lincoln and U.S. DOE agreed to continue into Phase 2 of the project without pursuing the development of higher pressure capabilities as originally planned. At 250 bar, development of equipment for hydrogen transport is supported by strong activity in the adjacent natural gas transportation sector. Trade studies performed since 2011 indicate optimization of hauling efficiency and system cost for hydrogen transport at about 350 bar (5076 psi). However, due to reduced efficiency of compression of natural gas above 250 bar, 350 bar operation is not an attractive option for natural gas transportation. The CHG market is not developed at this time, and it is difficult to forecast the arrival of significant revenues. On the investment side, the cost to fully qualify a large tank module at 350 bar is estimated at $3MM to $5MM. There is insufficient CHG market definition to support a stand-alone business case for this investment without near term revenue in the adjacent CNG transportation market. Therefore development of a 350 bar TITAN® system was deferred and not pursued under this project. Hexagon Lincoln continues to support the development of tankage and equipment for operation at 350 bar and above; with 700 bar vehicle tanks and 950 bar tanks for ground storage applications. Phase 2 activities were focused on reducing system cost, increasing system capacity, increasing system safety and characterization of polymer material performance specific to hydrogen pressure vessel usage. With the successful launch of TITAN® modules and trailers in natural gas transportation, over 600 units have been produced through the end of 2016, resulting in improved purchasing power for raw materials and manufactured components. This has allowed Hexagon Lincoln to approach the current project goals for system cost. At $590/kg of compressed hydrogen delivered, the system cost of the baseline TITAN® module is below the project’s 2015 target of $730/kg H2 delivered, and very close to the project’s 2020 target of $575/kg H2 delivered. [Based on product pricing in 1Q2017.] Emphasis was placed on configuration of larger capacity systems within the vehicle weights and dimensions allowed on federal and state highways in the United States and other countries. These activities resulted in the design and development of integrated tube trailer systems that have increased delivery capacities by 45%. The hydrogen delivery capacity of our largest system is 845 kg, exceeding the project’s 2015 target of 700 kg H2 delivered. Emerging technologies offering improvement of the safety systems used on the equipment were investigated, with particular focus on improving the reliability and cost of the emergency venting system for fire protection. Finally, investment in our materials laboratory improved detection and characterization of hydrogen-induced damage in polymer materials, supporting the development of operational protocols to avoid damage to pressure vessel liners and valve components.
We present preliminary results of the Roofline Toolkit for multicore, many core, and accelerated architectures. This paper focuses on the processor architecture characterization engine, a collection of portable instrumented micro benchmarks implemented with Message Passing Interface (MPI), and OpenMP used to express thread-level parallelism. These benchmarks are specialized to quantify the behavior of different architectural features. Compared to previous work on performance characterization, these microbenchmarks focus on capturing the performance of each level of the memory hierarchy, along with thread-level parallelism, instruction-level parallelism and explicit SIMD parallelism, measured in the context of the compilers and run-time environments. We also measure sustained PCIe throughput with four GPU memory managed mechanisms. By combining results from the architecture characterization with the Roofline model based solely on architectural specifications, this work offers insights for performance prediction of current and future architectures and their software systems. To that end, we instrument three applications and plot their resultant performance on the corresponding Roofline model when run on a Blue Gene/Q architecture.
One of the main focus areas of the 3013 Surveillance Program is a thorough evaluation of the inner container closure weld region (ICCWR) opened for destructive examination (DE). As part of the protocol to investigate the corrosion in the ICCWR a laser confocal microscope (LCM) is used to perform close visual examination of the surface and measurements of corrosion features on the surface. DE containers from FY13 through FY16 were screened with three candidates selected for full circumference evaluation (FCE) according to the ICCWR examination protocol, During the FCE, FY16 DE05 and FY15 DE07 showed suspect major corrosion events, FY16 DE05 Section C2 shows two crack-like features, identified as Denebola and Draco. Both features are located at the boundary of Zone 2 and Zone 3. Consequently, Section C2 of FY16 DE05 was selected for examination by serial metallography at Savannah River National Laboratory (SRNL). For FY15 DE07 the suspect corrosion events were observed on Sections Cl and C2. Section Cl shows one crack-like feature, identified as Acrux. Section C2 shows three crack-like features, identified as Bellatrix, Cursa Minor and Cursa Major. Unlike Acrux and Bellatrix, which are located at the boundary of Zone 2 and Zone 3, Cursa Minor and Cursa Major are located in Zone 2. Sections Cl and C2 of FY15 DE07 were sent to Los Alamos National Laboratory (LANE) for characterization by X-Ray Tomography (XRT).
The goal of this project is the development of novel catalysts and knowledge of reaction pathways and mechanisms for conversion of biomass-based compounds to fuels that are compatible with oil-based fuels and with acceptable or superior fuel properties. The research scope included both catalysts to convert lignocellulosic biomass-based molecules (from pyrolysis) and vegetable oil-based molecules (i.e., triglycerides and fatty acid methyl esters). This project comprised five technical tasks. Each task is briefly introduced below, and major technical accomplishments summarized. Technical accomplishments were described in greater detail in the quarterly progress reports, and in even more detail in the >50 publications acknowledging this DoE project funding (list of publications and presentations included at the end of this report). The results of this research added greatly to the knowledge base necessary for upgrading of pyrolysis oil to hydrocarbon fuels and chemicals, and for conversion of vegetable oils to fungible diesel fuel. Numerous new catalysts and catalytic reaction systems were developed for upgrading particular compounds or compound families found in the biomass-based pyrolysis oils and vegetable oils. Methods to mitigate catalyst deactivation were investigated, including novel reaction/separation systems. Performance and emission characteristics of biofuels in flames and engines were measured. Importantly, the knowledge developed from this project became the basis for a subsequent collaborative proposal led by our research group, involving researchers from the University of Wisconsin, the University of Pittsburg, and the Idaho National Lab, for the DoE Carbon, Hydrogen and Separations Efficiency (CHASE) program, which was subsequently funded (one of only four projects awarded in the CHASE program). The CHASE project examined novel catalytic processes for lignocellulosic biomass conversion as well as technoeconomic analyses for process options for maximum carbon capture and hydrogen efficiency. Our research approach combined catalyst synthesis, measurements of catalyst activity and selectivity in different reactor systems and conditions, and detailed catalyst characterization to develop fundamental understanding of reaction pathways and the capability to predict product distributions. Nearly all of the candidate catalysts were prepared in-house via standard techniques such as impregnation, co-impregnation, or chemical vapor deposition. Supports were usually purchased, but in some cases coprecipitation was used to simultaneously create the support and active component, which can be advantageous for strong active component-support interactions and for achieving high active component dispersion. In-house synthesis also allowed for studies of the effects on catalyst activity and selectivity of such factors as support porosity, calcination temperature, and reduction/activation conditions. Depending on the physical characteristics of the molecule, catalyst activity measurements were carried out in tubular flow reactors (for vapor phase reactions) or stirred tank reactors (for liquid phase reactions) over a wide range of pressures and temperatures. Reactant and product concentrations were measured using gas chromatography (both on-line and off-line, with TCD, FID, and/or mass spectrometric detection). For promising catalysts, detailed physicochemical characterization was carried out using FTIR, Raman, XPS, and XRD spectroscopies (all available in our laboratories) and TEM spectroscopy (available at OU). Additional methods included temperature programmed techniques (TPD, TPO) and surface area measurements by nitrogen adsorption techniques.
This report describes the research accomplished under the award topic of “Controlling Superconductivity via Tunable Nanostructure Arrays.” Under this program, proximity-coupled nanostructure arrays were experimentally and theoretically studied, to understand and control how collective behavior emerges in superconducting systems. The outcome of this research was the discovery and characterization of exotic phases in superconducting systems, a better understanding of how microscopic parameters lead to macroscopic behavior in key materials systems, and an improved ability to control interactions to manipulate the electronic properties of superconductors. The program was based on the idea that superconducting islands placed on a thin conductor at a separation smaller than the normal metal coherence length can support a finite Josephson coupling between the islands, where the strength of the coupling depends on the length and conductance of the intervening material. By adjusting the size, configuration, and type of islands, the correlated states, as well as the competition between them, were precisely tuned. This allowed for the clear determination of how superconductors’ critical properties, such as fundamental vortex dynamics, can be controlled.
This report summarizes results of the risk analysis and characterization of CO 2 and brine leakage potential of Farnsworth Unit (FWU) wells. U.S. DOE’s National Risk Assessment Partnership (NRAP) program works on quantitatively assess long-term environmental risks amidst significant geologic uncertainty and variability. NRAP risk assessment and computational tools are developed to quantify uncertainties and calculate risk associated with geologic sequestration of carbon dioxide (CO 2 ). For this study, we have developed a workflow from University of Utah’s physics-based reservoir simulators to performing leakage calculations using NRAP Tools. NRAP tools (NRAP-IAM-CS, RROM-Gen) are used to conduct leakage risk analysis based on Eclipse simulation results, and characterize wellbore leakage at the Farnworth Site. This report summarizes results of the risk analysis and characterization of CO 2 and brine leakage potential of Farnsworth Unit (FWU) wells.
Information about the times of thermal breakthrough and subsequent rates of thermal drawdown in enhanced geothermal systems (EGS) is necessary for reservoir management, designing fracture stimulation and well drilling programs, and forecasting economic return. Thermal breakthrough in heterogeneous porous media can be estimated using conservative tracers and assumptions about heat transfer rates; however, tracers that undergo temperature-dependent changes can provide more detailed information about the thermal profile along the flow path through the reservoir. To be effectively applied, the thermal reaction rates of such temperature sensitive traces must be well characterized for the range of conditions that exist in geothermal systems. Reactive tracers proposed in the literature include benzoic and carboxylic acids (Adams) and organic esters and amides (Robinson et al.); however, the practical temperature range over which these tracers can be applied (100-275°C) is somewhat limited. Further, for organic esters and amides, little is known about their sorption to the reservoir matrix and how such reactions impact data interpretation. Another approach involves tracers where the reference condition is internal to the tracer itself. Two examples are: 1) racemization of polymeric amino acids, and 2) mineral thermoluminescence. In these cases internal ratios of states are measured rather than extents of degradation and mass loss. Racemization of poly-L-lactic acid (for example) is temperature sensitive and therefore can be used as a temperature-recording tracer depending on the rates of racemization and stability of the amino acids. Heat-induced quenching of thermoluminescence of pre-irradiated LiF can also be used. To protect the tracers from alterations (extraneous reactions, dissolution) in geothermal environments we are encapsulating the tracers in core-shell colloidal structures that will subsequently be tested for their ability to be transported and to protect the tracers from incidental reactions. We review the criteria for practical reactive tracers, which serves as the basis for experimental testing and characterization and can be used to identify other potential candidate tracers. We will also discuss the information obtainable from individual tracers, which has implications for using multiple tracers to obtain information about the thermal history of a reservoir. We will provide an update on our progress for conducting proof-of-principle tests for reactive tracers in the Raft River geothermal system.
Radioactive waste disposal in shale/argillite rock formations has been widely considered given its desirable isolation properties (low permeability), geochemically reduced conditions, anomalous groundwater pressures, and widespread geologic occurrence. Clay/shale rock formations are characterized by their high content of clay minerals such as smectites and illites where diffusive transport and chemisorption phenomena predominate. These, in addition to low permeability, are key attributes of shale to impede radionuclide mobility. Shale host-media has been comprehensively studied in international nuclear waste repository programs as part of underground research laboratories (URLs) programs in Switzerland, France, Belgium, and Japan. These investigations, in some cases a decade or more long, have produced a large but fundamental body of information spanning from site characterization data (geological, hydrogeological, geochemical, geomechanical) to controlled experiments on the engineered barrier system (EBS) (barrier clay and seals materials). Evaluation of nuclear waste disposal in shale formations in the USA was conducted in the late 70’s and mid 80’s. Most of these studies evaluated the potential for shale to host a nuclear waste repository but not at the programmatic level of URLs in international repository programs.
The bright future of particle physics at the Energy and Intensity frontiers poses exciting challenges to the scientific software community. The traditional strategies for processing and analyzing data are evolving in order to (i) offer higher-level programming model approaches and (ii) exploit parallelism to cope with the ever increasing complexity and size of the datasets. This contribution describes how the ROOT framework, a cornerstone of software stacks dedicated to particle physics, is preparing to provide adequate solutions for the analysis of large amount of scientific data on parallel architectures. The functional approach to parallel data analysis provided with the ROOT TDataFrame interface is then characterized. The design choices behind this new interface are described also comparing with other widely adopted tools such as Pandas and Apache Spark. The programming model is illustrated highlighting the reduction of boilerplate code, composability of the actions and data transformations as well as the capabilities of dealing with different data sources such as ROOT, JSON, CSV or databases. Details are given about how the functional approach allows transparent implicit parallelization of the chain of operations specified by the user. The progress done in the field of distributed analysis is examined. In particular, the power of the integration of ROOT with Apache Spark via the PyROOT interface is shown. In addition, the building blocks for the expression of parallelism in ROOT are briefly characterized together with the structural changes applied in the building and testing infrastructure which were necessary to put them in production.
Continuing the scaling of quantum computers hinges on building classical control hardware pipelines that are scalable, extensible, and provide real time response. The instruction set architecture (ISA) of the control processor provides functional abstractions that map high-level semantics of quantum programming languages to low-level pulse generation by hardware. Here, we provide a methodology to quantitatively assess the effectiveness of the ISA to encode quantum circuits for intermediate-scale quantum devices with O(10 2 ) qubits. The characterization model that we define reflects performance, the ability to meet timing constraint implications, scalability for future quantum chips, and other important considerations making them useful guides for future designs. Using our methodology, we propose scalar (QUASAR) and vector (qV) quantum ISAs as extensions and compare them with other ISAs in metrics such as circuit encoding efficiency, the ability to meet real-time gate cycle requirements of quantum chips, and the ability to scale to more qubits.
Here, we develop a convenient framework for characterizing multipartite entanglement in composite systems, based on relations between entropies of various subsystems. This continues the program initiated in [1], of using holography to effectively recast the geometric problem into an algebraic one. We prove that, for an arbitrary number of parties, our procedure identifies a finite set of entropic information quantities that we conveniently represent geometrically in the form of an arrangement of hyperplanes. This leads us to define the holographic entropy arrangement, whose algebraic and combinatorial aspects we explore in detail. Using the framework, we derive three new information quantities for four parties, as well as a new infinite family for any number of parties. A natural construct from the arrangement is the holographic entropy polyhedron which captures holographic entropy inequalities describing the physically allowed region of entropy space. We illustrate how to obtain the polyhedron by winnowing down the arrangement through a sieve to pick out candidate sign-definite information quantities. Comparing the polyhedron with the holographic entropy cone, we find perfect agreement for 4 parties and corroborating evidence for the conjectured 5-party entropy cone. Lastly, we work with explicit configurations in arbitrary (time-dependent) states leading to both simple derivations and an intuitive picture of the entanglement pattern.