Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Nonlinear responses”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57

The 3-D inelastic analysis methods for hot section components (base program)

A series of computer codes are sought that would permit more accurate and efficient three-dimensional inelastic structural analysis of combustor liners, turbine blades, and turbine vanes. Each code embodies a progression of mathematical models for increasingly comprehensive representation of the geometrical features, loading conditions, and forms of nonlinear material response that distinguish these three groups of hot section components.

Todd, E. S.↗

Effect of Gimbal friction modeling technique on control stability and performance for Centaur upper-stage

The powered-phase autopilot for the Centaur upper stage rocket uses an autopilot forward loop gain scheduler that decreases the proportional gain as propellant mass is depleted. Nonlinear time response simulation studies revealed that Centaur vehicles with low-gain autopilots would have large attitude error limit cycles. These limit cycles were due to the assumed presence of Coulomb friction in the engine gimbals. This situation could be corrected through the use of an harmonic dither, programmed into the on-board digital computer and added to the engine command signal. This would introduce impending motion to the engines, allowing control of the engines even under small commands. Control authority was found to be restored when dither was used. A concern arose that the Centaur could be unacceptably excited at resonances near the dither frequency, if the dither amplitude was to be chosen on the basis of friction level present, a test was conducted to measure this level. Dither characteristics were to be based on the test results. The test results showed that the gimbal friction characteristic was actually hysteretic rather than the assumed Coulomb friction. The simulation results showed that, using this new model of gimbal friction, dither would no longer be necessary.

Graham, Ronald E.↗

Nonlinear shell analyses of the SRB/ETA ring interface

Two-dimensional shell models of the portion of the solid rocket booster (SRB) with the external tank attachment (ETA) ring were developed using the STAGSC-1 computer code. These analyses were performed in support of the SRB recertification program underway at the NASA Marshall Space Flight Center. The purpose of these analyses is to calculate the overall stress and deflection distributions for the SRB/ETA ring interface. An overview of the SRB/ETA ring geometry is presented followed by a discussion of the analysis methods and finite element models. Finally, the nonlinear structural response of the SRB/ETA ring interface is discussed.

Knight, Norman F., Jr.↗

Effect of gimbal friction modelling technique on control stability and performance for Centaur upper stage

The powered-phase autopilot for the Centaur upper stage rocket uses an autopilot forward loop gain scheduler that decreases the proportional gain as propellant mass is depleted. Nonlinear time response simulation studies revealed that Centaur vehicles with low-gain autopilots would have large attitude error limit cycles. These limit cycles were due to the assumed presence of Coulomb friction in the engine gimbals. This situation could be corrected through the use of an harmonic dither, programmed into the on-board digital computer and added to the engine command signal. This would introduce impending motion to the engines, allowing control of the engines even under small commands. Control authority was found to be restored when dither was used. A concern arose that the Centaur could be unacceptably excited at resonances near the dither frequency, if the dither amplitude was to be chosen on the basis of friction level present, a test was conducted to measure this level. Dither characteristics were to be based on the test results. The test results showed that the gimbal friction characteristic was actually hysteretic rather than the assumed Coulomb friction. The simulation results showed that, using this new model of gimbal friction, dither would no longer be necessary.

Graham, Ronald E.↗

3-D inelastic analysis methods for hot section components

The objective is to produce a series of new computer codes that permit more accurate and efficient three dimensional inelastic structural analysis of combustor liners, turbine blades, and turbine vanes. Each code embodies a progression of mathematical models for increasingly comprehensive representaion of the geometrical features, loading conditions, and forms of nonlinear material response that distinguish these three groups of hot section components.

Todd, E. S.↗

High temperature stress-strain analysis

The objectives of the high temperature structures program are threefold: to assist in the development of analytical tools needed to improve design analysis and procedures for the efficient and accurate prediction of the nonlinear structural response of hot-section components; to aid in the calibration, validation, and evaluation of the analytical tools by comparing predictions with experimental data; and to evaluate existing as well as advanced temperature and strain measurement instrumentation.

Thompson, Robert L.↗

Pressure induced ageing of polymers

The nonlinearly viscoelastic response of an amorphous homopolymer is considered under aspects of time dependent free volume behavior. In contrast to linearly viscoelastic solids, this model couples shear and volume deformation through a shift function which influences the rate of molecular relaxation or creep. Sample computations produce all those qualitative features one observes normally in uniaxial tension including the rate dependent formation of a yield point as a consequence of the history of an imposed pressure.

Emri, I.↗

Model-size reduction for the non-linear dynamic analysis of quasi-symmetric structures

A numerical technique is developed to reduce the size of models describing the nonlinear dynamic response of quasi-symmetric structures (i.e., structures with unsymmetric geometry). The response vectors of the structure are approximated by a linear combination of the symmetric and antisymmetric vectors at each time step. The mathematical formulation and numerical implementation of the method are described in detail, and results for a shallow laminated anisotropic panel of quadrilateral planform are presented in graphs and normalized contour plots.

Noor, Ahmed K.↗

Numerical analysis of discrete fractional integrodifferential structural dampers

This paper develops solution algorithms enabling the handling of the dynamic response of nonlinear structures contained discretely attached dampers modeled by fractional integrodifferential operators of the Grunwald-Liouville-Riemann type. The development consists of two levels of formulation, namely: (1) numerical approximations of fractional operators and, (2) the establishment of global level implicit schemes enabling the solution to nonlinear structural formulations. To generalize the overall results, error estimates are derived for the fractional operator approximation algorithm. These enable an ongoing optimization of solution efficiency for a given error tolerance. To benchmark the scheme, the results of several numerical experiments are presented. These illustrate the numerical characteristics of the overall formulation.

Padovan, Joseph↗

The dynamic behaviour of postbuckled composite plates under acoustic excitation

The Rayleigh-Ritz method was used to find the postbuckling static displacement pattern of a composite plane (CFRP) under uniaxial in-plane compression of uniform edge-shortening. The resonance frequencies and mode shapes at various postbuckled states are then evaluated by eigenvalue analysis of the dynamical matrix equation consisting of up-dated tangential stiffness matrix at corresponding static configuration. The theoretical results are compared with experimental results obtained in 16-layered CFRP laminate of aspect ratio 1.5. The resonance frequencies and mode shapes obtained are used to interpret the multimodal and nonlinear strain responses to high level of acoustic excitation. The dominance of second-mode contribution and softening-spring behavior are found in the strain response of postbuckled plates.

Ng, C. F.↗

Evaluation and applicability of transfinite element formulations with particular reference to radiation

The evaluation and applicability of hybrid transfinite element formulations are described for transient nonlinear thermal models with particular reference to account for radiation effects. The formulations are developed from basic concepts and evaluated for both one- and two-dimensional thermal models. The methodology presented is a hybrid approach as it combines finite elements, classical Galerkin schemes, and transform methods. Basic features of the hybrid formulations and the associated solution scheme used are first described. Therein, numerical test models are presented to evaluate the applicability for predicting the nonlinear transient response in one- and two-dimensional thermal models influenced due to radiation effects.

Tamma, Kumar K.↗

Interaction of feel system and flight control system dynamics on lateral flying qualities

An investigation of feel system and flight control system dynamics on lateral flying qualities was conducted using the variable stability USAF NT-33 aircraft. Experimental variations in feel system natural frequency, force-deflection gradient, control system command architecture type, flight control system filter frequency, and control system delay were made. The experiment data include pilot ratings using the Cooper-Harper (1969) rating scale, pilot comments, and tracking performance statistic. Three test pilots served as evaluators. The data indicate that as the feel system natural frequency is reduced lateral flying qualities degrade. At the slowest feel system frequency, the closed-loop response becomes nonlinear with a 'bobweight' effect apparent in the feel system. Feel system influences were essentially independent of the control system architecture. The flying qualities influence due to the feel system was different than when the identical dynamic systenm was used as a flight control system element.

Bailey, Randall E.↗

On 3-D inelastic analysis methods for hot section components

The objective of this program is to produce a series of new computer codes that permit more accurate and efficient three-dimensional inelastic structural analysis of combustor liners, turbine blades, and turbine vanes. Each code embodies a progression of mathematical models for increasingly comprehensive representation of the geometrical features, loading conditions, and forms of nonlinear material response that distinguish these three groups of hot section components.

Todd, E. S.↗

High temperature stress-strain analysis

The objectives of the high-temperature structures program are threefold: to assist in the development of analytical tools needed to improve design analyses and procedures for the efficient and accurate prediction of the nonlinear structural response of hot-section components; to aid in the calibration, validation, and evaluation of the analytical tools by comparing predictions with experimental data; and to evaluate existing as well as advanced temperature and strain measurement instrumentation. As the analytical tools, test methods, tests, instrumentations, as well as data acquisition, management, and analysis methods are developed and evaluated, a proven, integrated analysis and experiment method will result in a more accurate prediction of the cyclic life of hot section components.

Thompson, Robert L.↗

Three-dimensional inelastic analysis methods for hot section components

The objective of this program is to produce a series of new computer codes that permit more accurate and efficient three-dimensional inelastic structural analysis of combustor liners, turbine blades, and turbine vanes. Each code embodies a progression of mathematical models for increasingly comprehensive representation of the geometrical features, loading conditions, and forms of nonlinear material response that distinguish these three groups of hot section components.

Todd, E. S.↗

Scaling effects in the static large deflection response of graphite-epoxy composite beams

Scaling effects in the large deflection response of graphite-epoxy composite beams was investigated. Eight different scale model beams ranging from 1/6 to full-scale were subjected to an eccentric axial compressive load to promote large bending deformations and failures. Beams having laminate stacking sequences including unidirectional, angle ply, cross ply, and quasi-isotropic were tested to examine a wide variety of composite response and failure modes. The model beams were loaded under scaled test conditions until catastrophic failure. Data acquired included load, end displacement, and strain measurements, and qualitative failure measurements. The experimental data is compared to a large rotation beam analysis and a finite element model analysis. Results from the tests indicate that the beam response becomes nonlinear. Failure modes are consistent between scale models within a laminate family, however, a significant scale effect is observed in strength of the scaled beams.

Jackson, Karen E.↗

Scaling effects in the static large deflection response of graphite-epoxy composite beams

In the present investigation of scaling effects in the large-deflection response of graphite/epoxy composite beams, eight model beams ranging from 1/6 to full scale in size were subjected to an eccentric axial compressive load promoting large bending deformations and failures; the beams encompassed unidirectional, angle-ply, cross-ply, and quasi-isotropic types. The data obtained pertains to loads, end-displacements, strain measurememts, and qualitative failure measurements. Test results indicate that beam responses scale in the small-deflection region, but deviate as the response becomes nonlinear.

Jackson, Karen E.↗

Three-dimensional thermal-structural analysis of a swept cowl leading edge subjected to skewed shock-shock interference heating

A three-dimensional flux-based thermal analysis method has been developed and its capability is demonstrated by predicting the transient nonlinear temperature response of a swept cowl leading edge subjected to intense three-dimensional aerodynamic heating. The predicted temperature response from the transient thermal analysis is used in a linear elastic structural analysis to determine thermal stresses. Predicted thermal stresses are compared with those obtained from a two-dimensional analysis which represents conditions along the chord where maximum heating occurs. Results indicate a need for a three-dimensional analysis to predict accurately the leading edge thermal stress response.

Polesky, Sandra P.↗