Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Milling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Nanometer-Scale Imaging of Inhomogeneous Active Charge Carriers in Arsenic-Doped CdTe Thin Films

We report nanometer-scale imaging of active carrier distribution of As-doped CdTe films by scanning capacitance microscopy (SCM). We developed SCM sample preparation for CdTe by ion-milling followed by thermal processing. The nanometer-resolution carrier delineation for CdTe was validated by imaging on a CdTe cross-section sample made by a molecular beam epitaxy layer stack with As-doping concentrations of 10^15 ~10^18 /cm 3 . We found that the carrier distribution in As-doped films was significantly nonuniform, with inhomogeneity ranging from sub-um to a few um and concentration variation of one order of magnitude (low 10^16 to low 10^17 /cm 3 ). This nonuniformity is distributed randomly, independent of grain structure and grain boundary (GB). We used Kelvin probe force microscopy (KPFM) and cathodoluminescence (CL) to further map the surface potential and radiative illumination on the same area as the SCM image. Higher potential and lower CL intensity were found on GBs but not on SCM contrast, illustrating positive GB charging and GB recombination but not GB-distinguished doping. The overall KPFM potential image is in rough agreement with the SCM carrier distribution, in terms of Fermi-level position relative to the bandgap edge - thus resulting in the band-edge potential fluctuation. Nonuniform carrier concentration, potential fluctuation, and defect recombination can all together cause the Voc deficit of the As-doped CdTe device.

14 SOLAR ENERGY↗
DOE OSTI2021

Local Resistance Measurement for Degradation of c-Si Heterojunction with Intrinsic Thin Layer (HIT) Solar Modules

Silicon heterojunction with intrinsic thin layer (or HIT) modules typically degrade at a rate of less than 1% annually in solar fields with dominant degradation in open-circuit voltage and some degradation in series resistance. However, detailed mechanisms can differ from module to module. Here, we study increases in local series resistance that occur over long-term field deployment, indicated by cell areas where the photoluminescence intensity does not degrade but the electroluminescence degrades significantly. To directly measure the local series resistance, we have cored out the local electroluminescence-degraded area, and we measured the sheet resistance by 4-point-probe and local nm-scale resistance using scanning spreading resistance microscopy (SSRM). The results by 4-point-probe show scattered sheet resistance that can be caused, for example, by nonuniform current paths through the transparent conductive oxide layer, the a-Si:H emitter, or the near-junction c-Si inversion layer. In contrast, the SSRM results indicate a relatively uniform and non-degraded resistivity on smaller nanometer spatial scales. SSRM is an atomic force microscopy-based two-terminal resistance mapping technique that measures the local resistance in nm-volume beneath the probe. The consistent resistances measured on the control and degraded samples can exclude the degradation of transparent conductive oxide resistance.

41 EE - Solar Energy Technologies Office (EE-4S)↗
DOE OSTI2024

Field Study of Nighttime Leakage Currents in Bifacial PV Modules: Correlation with Atmospheric Electric Field Data

Leakage currents measured on PV modules in the field originate from a potential difference between the modules' frame and the cells. They can be a relative indicator of Potential-Induced Degradation (PID) severity, especially when comparing the same module design in a different environment. As modules are not operating at night, no leakage current should be observed but our team has reported several events of nighttime leakage currents on bifacial PV modules. These events have been firstly observed during a thunderstorm that are characterized by strong atmospheric electrical field values. This lead us to believe that nighttime leakage currents could originate from the atmospheric electric charges. In this paper, we correlate nighttime leakage currents measured on bifacial PV modules with field mill data to identify the origin of nighttime leakage currents. Our results show that so far, no leakage currents at night occur when the atmospheric electric field is between 0 and 150–200 V/m (standard value for fair weather). As soon as the atmospheric electric field is out of this range, leakage currents are observed with or without rain involved. This suggests a transport of charged particles from the atmosphere to the modules' frame. A combination of heavy rain with strong atmospheric electric field results into high nighttime leakage currents with a magnitude up to 8 times higher than what observed during the day with -1500V applied. This is explained by an easier transport of the charged particles through the water droplets. Based on these results, leakage currents observed during the day might not be only due to the inherent potential difference between the frame and the cells depending on the atmospheric electric field activity. We believe that it should be taken into account in PID studies.

14 SOLAR ENERGY↗
DOE OSTI2020

Characterization and differentiation of aluminum powders used in improvised explosive devices – Part 1: Proof of concept of the utility of particle micromorphometry

Abstract Aluminum (Al) powders are commonly used in improvised explosive devices as metallic fuels, a component of explosive mixtures. These powders can be obtained readily from industrial‐scale and consumer products, and produced using unsophisticated “kitchen chemistry” techniques. This research demonstrates the potential of automated particle micromorphometry for comparisons between known source and questioned Al powders recovered from IEDs, as well as for insight into the method of Al powder manufacture. Al powder samples were obtained from legitimate manufacturers, and 56 samples were produced “in‐house” from Al‐containing spray paints and ball‐milled Al foils. Transmitted light microscope images of Al powder particles were acquired using an automated stage with automated z‐focus; 17 size and shape parameters were measured for all particles. Approximately 37,000–2,500,000 particles/sample were analyzed using an open‐source statistical package with customized code. Dimensionality reduction was required for processing the large datasets: eight of the 17 measured variables were selected based on inspection of the correlation matrix. Data from four subsamples from each of the 56 samples produced using “in‐house” methods were analyzed using ANOVA to assess the within‐ and between‐sample variation. High within‐sample variation was noted; however, ANOVA and post‐hoc Tukey's honestly significant difference (HSD) tests demonstrated that the between‐sample variation was substantially larger than the within‐sample variation. Each sample could be differentiated from all other samples in the test set. Future experiments will focus on ways to reduce the within‐sample variation, and additional statistical and microanalytical methods to classify sources and confidently constrain the method of Al powder manufacture.

Baldaino, JenaMarie↗
DOE OSTI2024

Porous Ti 3 AlC 2 MAX phase enables efficient synthesis of Ti 3 C 2 T x MXene

Abstract MXenes, a large family of two‐dimensional carbides and/or nitrides, are among the most studied materials worldwide due to their great diversity of structures and compositions. Their unique properties find use in several applications. Typically, they are manufactured by selective wet‐chemical etching of layered MAX phase ceramics, which are produced nowadays primarily for MXene synthesis. However, the synthesis of MAX phases has not been changed since the time of their use in structural and high‐temperature applications, and it has not been optimized for MXene manufacturing. The main purpose of this study is to develop a porous Ti 3 AlC 2 MAX phase that can be easily ground into individual grains without time‐consuming, harsh, and tedious crushing and milling steps. Moreover, we also demonstrate the synthesis of highly porous Ti 3 AlC 2 from an inexpensive titanium sponge instead of a highly pure titanium powder and explain the mechanisms of reaction sintering and formation of porous MAX phase. MXene obtained from this MAX phase, Ti 3 C 2 Tx, shows larger flake size and higher electrical conductivity in thin films, compared to the materials produced from the costly fine titanium powder. The proposed approach may apply to the synthesis of other MAX phases as well.

Materials Science↗
DOE OSTI2026

Flash electropolishing for TEM: Reducing FIB‐induced defects in tungsten with protocols for new materials

Focused ion beam (FIB) milling has become the dominant approach for site-specific transmission electron microscopy (TEM) specimen preparation; however, FIB damage remains a critical limitation for reliable microstructural characterisation, particularly in radiation effects studies. Tungsten is especially susceptible to FIB damage due to its high nuclear stopping power, which promotes the formation and strong diffraction contrast of FIB-induced ‘black spot’ defects that are indistinguishable from very fine irradiation-induced loops/defects resulting from low to intermediate temperature neutron irradiation. In this work, flash electropolishing is systematically evaluated as a post-FIB treatment for minimising preparation-induced artefacts for TEM analysis of tungsten-based alloys. Using a range of non-, ion-, and neutron-irradiated tungsten materials, the effectiveness of flash electropolishing has been assessed through direct comparison with conventional FIB and plasma-FIB preparation including low-energy Ga, Ar, Xe ion cleaning. The results demonstrate that flash electropolishing effectively removes FIB-damaged layers and ‘black spot’ defects, thereby enabling reliable observation of irradiation-induced dislocation structures. Key processing parameters governing flash electropolishing quality – including lamella thickness, applied voltage, polishing duration, electrolyte chemistry, and cathode geometry – have been systematically evaluated, and clear criteria were established for determining when flash electropolishing is required to ensure reliable microstructural analysis. This work also provides practical guidance for implementing flash electropolishing as an artefact-controlled specimen-preparation approach for TEM characterisation of FIB-produced specimens. The systematic protocol can be extended to other, non-tungsten materials.

TEM sample preparation↗
DOE OSTI2022

Indirect Tool Condition Monitoring Using Ensemble Machine Learning Techniques

Abstract Tool condition monitoring (TCM) has become a research area of interest due to its potential to significantly reduce manufacturing costs while increasing process visibility and efficiency. Machine learning (ML) is one analysis technique which has demonstrated advantages for TCM applications. However, the commonly studied individual ML models lack generalizability to new machining and environmental conditions, as well as robustness to the unbalanced datasets which are common in TCM. Ensemble ML models have demonstrated superior performance in other fields, but have only begun to be evaluated for TCM. As a result, it is not well understood how their TCM performance compares to that of individual models, or how homogeneous and heterogeneous ensemble models’ performances compare to one another. To fill in these research gaps, milling experiments were conducted using various cutting conditions, and the model groups were compared across several performance metrics. Statistical t-tests were also used to evaluate the significance of model performance differences. Through the analysis of four individual ML models and five ensemble models, all based on the processes’ sound, spindle power, and axial load signals, it was found that on average, the ensemble models performed better than the individual models, and that the homogeneous ensembles outperformed the heterogeneous ensembles.

Engineering↗
DOE OSTI2024

A High-Ceramic-Loading LATP–PVDF–Al 2 O 3 Composite Film for Lithium-Ion Batteries With Favorable Porous Microstructure and Enhanced Thermal Stability

A separator plays a crucial role in a Li-ion battery to carry liquid electrolytes while preventing short-circuiting between electrodes. Nevertheless, conventional commercial separators often exhibit poor wettability and are prone to shrink at elevated temperatures due to their limited thermal stability. Herein, we report a heat-resistant LATP–PVDF–Al 2 O 3 composite film with outstanding wetting performance. The thin film was prepared using ball mill mixing and tape-casting processes. Two solvents, NMP and glycerol, were applied to prepare the slurry, and a favorable microstructure in the film was created after drying. Here, the ionic conductivity of the film was tested at 1.39 mS cm –1 when paired with liquid electrolyte, almost double that of the commercial counterpart. The high ceramic loading of 70% improved both the thermal shrinkage resistance and dendrite inhibition of the membrane. When assembled in an NMC half-cell, the cycling capacity retentions of 92.8% and 92.1% are achieved after 50 cycles at 0.5 C and 1 C, demonstrating its capability to be used in Li-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2024

A FeCrAl-Al2O3 Composite Produced via Laser Powder Bed Fusion of a Mixed Powder for Porous Catalyst Scaffolds

This study proposes a novel approach for synthesizing and etching bicontinuous FeCrAl-Al2O3 composites as a means for replacing FeCrAl foams as catalyst scaffolds in bio-driven alcohol reactors for jet-fuel production. Conventional FeCrAl foams suffer from poor availability and consequent high costs. New additive manufacturing techniques provide an opportunity to produce tailored foams in reasonable times and at acceptable costs. This research aimed to generate a porous FeCrAl structure by etching a bicontinuous FeCrAl-Al2O3 composite produced by laser powder bed fusion of amalgamated FeCrAl and Al2O3 powders. The composite powder for laser powder bed fusion is created by ball-milling FeCrAl and Al2O3 powders. This research focuses on achieving a bi-continuous FeCrAl-Al2O3 structure, essential for the selective removal of the ceramic phase. The influence of laser processing parameters on the microstructure was examined across a range of laser powers (60-120 W) and scan speeds (100-400 mm/s), showing that higher powers and speeds produce finer metal struts. A bi-continuous microstructure was consistently obtained, marking a key achievement. The Al2O3 removal process involved a two-step etching method using hydrochloric and phosphoric acids, tested across various etching times. The alumina phase was reduced from 36 vol% to 17 vol% (corresponding to an increase in porosity from 24 vol% to 43 vol%), showing the potential for use as a porous catalyst scaffold. This research demonstrates the potential for using additive manufacturing to produce porous FeCrAl structures capable of replacing hard-to-source FeCrAl foams.

Son, Kwangtae↗
DOE OSTI2023

PHASE CHANGE MATERIAL FOR THERMAL ENERGY STORAGE IN BUILDINGS BASED ON SODIUM SULFATE DECAHYDRATE AND DISODIUM HYDROGEN PHOSPHATE DODECAHYDRATE

The worldwide increasing energy demand and 2050 net zero carbon target urge the globe to solve the energy challenge. Thermal Energy Storage (TES) has received significant attention in recent years as TES can be integrated into heating, ventilation, and air-conditioning systems where the energy would be stored during low-demand times and dispatched during high-demand times, resulting in controlling the peak load and improving energy savings. Material development is an integral part of TES. Salt hydrates are appealing due to cost-effectiveness, low- to no toxicity, and their high melting enthalpy, where energy is stored as latent heat. However, most salt hydrates are prone to incongruent melting (i.e., phase separation upon melting), which results in poor stability and large supercooling. In this study, we produced a highly stable novel energy storage material at a composition of 32 wt% sodium sulfate decahydrate, 52 wt% sodium phosphate dibasic dodecahydrate, 12 wt% milled expanded graphite, and 4 wt% borax. The material has a melting temperature of 28°C and an energy storage capacity of 167 kJ/kg with a supercooling of less than 3°C. The system showed no loss in energy storage performance after 150 cycles. The findings suggest that the novel energy storage material developed in this might be utilized in building heating and cooling applications.

Turnaoglu, Tugba↗
DOE OSTI2020

Structural breakdown in high power GaN-on-GaN p-n diode devices stressed to failure

The morphology of GaN-on-GaN vertical p-i-n diode devices after reverse-bias electrical stressing to breakdown has been investigated. All failed devices had irreversible structural damage, showing large surface craters that were ∼15–35 μm deep with lengthy surface cracks. Cross-sectional electron micrographs of failed devices showed substantial concentrations of threading dislocations around the cracks and near the crater surfaces. Progressive ion-milling across damaged devices revealed high densities of threading dislocations and the presence of voids beneath the surface cracks; these features were not observed in any unstressed devices. These results should serve as a useful reference for future reliability studies of vertical high-power GaN devices.

Peri, Prudhvi (ORCID:000000022338441X)↗
DOE OSTI2026

Human NLRP3 inflammasome activation leads to formation of condensate at the microtubule organizing center

The NLRP3 inflammasome is a multiprotein molecular machine that drives inflammatory responses in innate immunity. Although its dysregulation is implicated in numerous human diseases, its structural organization in cells remains poorly understood. Here, we used precise fluorescence-guided cryo–focused ion beam (cryo-FIB) milling and cryo–electron tomography (cryo-ET) to visualize NLRP3 inflammasomes in situ within human macrophages at various stages of activation. After priming and activation, we observed expansion and dispersion of Golgi cisternae, along with the emergence of 50-nanometer NLRP3-associated vesicles, which likely transport NLRP3 to the MTOC. Dense NLRP3-containing condensates then formed in and around the MTOC. In later stages, the condensates solidified, coincident with widespread mitochondrial damage, autophagy, and pyroptotic cell death.

Wang, Jue [Division of Chemistry and Chemical Engi↗
DOE OSTI2021

Seismic fault weakening via CO 2 pressurization enhanced by mechanical deformation of dolomite fault gouges

Carbon dioxide emissions from dolomite decarbonation play an essential role in the weakening of carbonate faults by lowering the effective normal stress, which is thermally activated at temperatures above 600–700 °C. However, the mechanochemical effect of low-crystalline ultrafine fault gouge on the decarbonation and slip behavior of dolomite-bearing faults remains unclear. In this study, we obtained a series of artificial dolomite fault gouges with systematically varying particle sizes and dolomite crystallinities using a high-energy ball mill. The laboratory-scale pulverization of dolomite yielded MgO at temperatures below 50 °C, indicating that mechanical decarbonation without significant heating occurred due to the collapse of the crystalline structure, as revealed by X-ray diffraction and solid-state nuclear magnetic resonance results. Furthermore, the onset temperature of thermal decarbonation decreased to ~400 °C. Numerical modeling reproduced this two-stage decarbonation, where the pore pressure increased due to low-temperature thermal decarbonation, leading to slip weakening on the fault plane even at 400–500 °C; i.e., 200–300 °C lower than previously reported temperatures. Thus, the presence of small amounts of low-crystalline dolomite in a fault plane may lead to a severely reduced shear strength due to thermal decomposition at ~400 °C with a small slip weakening distance.

58 GEOSCIENCES↗
DOE OSTI2020

PANDA as midrapidity detector for a future HESR Collider at FAIR

Exciting new scientific opportunities are presented for the PANDA detector at the High Energy Storage Ring in the redefined $$\overline{\text {p}} \text {p}(A)$$ p ¯ p ( A ) collider mode, HESR-C, at the Facility for Antiproton and Ion Research (FAIR) in Europe. The high luminosity, $$L \sim 10^{31}$$ L ~ 10 31 cm $$^{-2}$$ - 2 s $$^{-1}$$ - 1 , and a wide range of intermediate and high energies, $$\sqrt{s_{\text {NN}}}$$ s NN up to 30 GeV for $$\overline{\text {p}} \text {p}(A)$$ p ¯ p ( A ) collisions will allow to explore a wide range of exciting topics in QCD, including the study of the production of excited open charm and bottom states, nuclear bound states containing heavy (anti)quarks, the interplay of hard and soft physics in the dilepton production, probing short-range correlations in nuclei, and the exploration of the early, complete $$\overline{\text {p}}$$ p ¯ -p- annihilation phase, where an initially pure Yang–Mills gluon plasma is formed.

Physics↗
DOE OSTI2021

Muon reconstruction and identification efficiency in ATLAS using the full Run 2 $pp$ collision data set at $\sqrt{s}=13$ TeV

This article documents the muon reconstruction and identification efficiency obtained by the ATLAS experiment for 139 fb$^{-1}$ of $pp$ collision data at $\sqrt{s}=13$ TeV collected between 2015 and 2018 during Run 2 of the LHC. The increased instantaneous luminosity delivered by the LHC over this period required a reoptimisation of the criteria for the identification of prompt muons. Improved and newly developed algorithms were deployed to preserve high muon identification efficiency with a low misidentification rate and good momentum resolution. The availability of large samples of $Z\to\mu\mu$ and $J/\psi\to\mu\mu$ decays, and the minimisation of systematic uncertainties, allows the efficiencies of criteria for muon identification, primary vertex association, and isolation to be measured with an accuracy at the per-mille level in the bulk of the phase space, and up to the percent level in complex kinematic configurations. Excellent performance is achieved over a range of transverse momenta from 3 GeV to several hundred GeV, and across the full muon detector acceptance of $|\eta|<2.7$.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2023

Search for pair production of third-generation leptoquarks decaying into a bottom quark and a $\tau $-lepton with the ATLAS detector

Abstract A search for pair-produced scalar or vector leptoquarks decaying into a b -quark and a $$\tau $$ τ -lepton is presented using the full LHC Run 2 (2015–2018) data sample of 139 fb $$^{-1}$$ - 1 collected with the ATLAS detector in proton–proton collisions at a centre-of-mass energy of $$\sqrt{s} =13$$ s = 13 TeV. Events in which at least one $$\tau $$ τ -lepton decays hadronically are considered, and multivariate discriminants are used to extract the signals. No significant deviations from the Standard Model expectation are observed and 95% confidence-level upper limits on the production cross-section are derived as a function of leptoquark mass and branching ratio $$\mathcal {B}$$ B into a $$\tau $$ τ -lepton and b -quark. For scalar leptoquarks, masses below 1460 GeV are excluded assuming $$\mathcal {B}=100$$ B = 100 %, while for vector leptoquarks the corresponding limit is 1650 GeV (1910 GeV) in the minimal-coupling (Yang–Mills) scenario.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

Search for leptoquark pair production decaying into $te^- \bar{t}e^+$ or $t\mu ^- \bar{t}\mu ^+$ in multi-lepton final states in pp collisions at $\sqrt{s} = 13\,\textrm{TeV}$ with the ATLAS detector

A search for leptoquark pair production decaying into $te^- \bar{t}e^+$ or $t\mu ^- \bar{t}\mu ^+$ in final states with multiple leptons is presented. The search is based on a dataset of pp collisions at $\sqrt{s}=13~\text {TeV}$ recorded with the ATLAS detector during Run 2 of the Large Hadron Collider, corresponding to an integrated luminosity of 139 fb -1 . Four signal regions, with the requirement of at least three light leptons (electron or muon) and at least two jets out of which at least one jet is identified as coming from a b-hadron, are considered based on the number of leptons of a given flavour. The main background processes are estimated using dedicated control regions in a simultaneous fit with the signal regions to data. No excess above the Standard Model background prediction is observed and 95% confidence level limits on the production cross section times branching ratio are derived as a function of the leptoquark mass. Under the assumption of exclusive decays into $te^{-}$ ($t\mu ^{-}$ ), the corresponding lower limit on the scalar mixed-generation leptoquark mass $m_{\textrm{LQ}_{\textrm{mix}}^{\textrm{d}}}$ is at 1.58 (1.59) TeV and on the vector leptoquark mass $m_{{\tilde{U}}_1}$ at 1.67 (1.67) TeV in the minimal coupling scenario and at 1.95 (1.95) TeV in the Yang–Mills scenario.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗