Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microstructural properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57

Influence of oxygen partial pressure on the microstructural and magnetic properties of Er-doped ZnO thin films

Er-doped ZnO thin films have been prepared by using inductively coupled plasma enhanced physical vapor deposition at different O{sub 2}:Ar gas flow ratio (R = 0:30, 1:30, 1:15, 1:10 and 1:6). The influence of oxygen partial pressure on the structural, optical and magnetic properties was studied. It is found that an appropriate oxygen partial pressure (R=1:10) can produce the best crystalline quality with a maximum grain size. The internal strain, estimated by fitting the X-ray diffraction peaks, varied with oxygen partial pressure during growth. PL measurements show that plenty of defects, especially zinc vacancy, exist in Er-doped ZnO films. All the samples show room-temperature ferromagnetism. Importantly, the saturation magnetization exhibits similar dependency on oxygen partial pressure with the internal strain, which indicates that internal strain has an important effect on the magnetic properties of Er-doped ZnO thin films.

36 MATERIALS SCIENCE↗

Preparing magnetic yttrium iron garnet nanodot arrays by ultrathin anodic alumina template on silicon substrate

Ultrahigh density periodically ordered magnetic yttrium iron garnet (Y{sub 3}Fe{sub 5}O{sub 12}, YIG) nanodot arrays have been prepared by pulsed laser deposition through an ultrathin alumina mask (UTAM). UTAM having periodically ordered circularly shaped holes with 350 nm in diameter, 450 nm in inter-pore distance, and 700 nm in height has been prepared on silicon substrate. Furthermore, the microstructure and magnetic properties of YIG nanodot arrays have been characterized. Nanodot arrays with a sharp distribution in diameter centered at 340 nm with standard deviation of 10 nm have been fabricated. Moreover, typical hysteresis loops and ferromagnetic resonance spectra in in-plane and out-of-plane revealed that this unique structure greatly influences the magnetics properties of YIG. First, coercivity of YIG nanodot arrays in in-plane was increased about from 15 Oe of YIG films to 500 Oe. Then, the degree of uniformity about nanodot height decided that two or more resonance peaks in out-of-plane were detected in the spectra. The peak-to-peak linewidth values were about 94 Oe and 40 Oe in the parallel and perpendicular directions, respectively, which indicated that the values were larger by the two-magnon scattering. Consequently, this pattering method creates opportunities for studying physics in oxide nanomagnets and may be applied in spin-wave devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The effect of gallium substitution on the microstructure and magnetic properties of yttrium iron garnet

Y{sub 3}Fe{sub (5-y)}Ga{sub y}O{sub 12} (y = 0, 0.4, 1.4 and 2,4) thin films were prepared by sol-gel method and annealed for 2h in oxygen. The thin film’s characteristic were studied by an X-ray diffraction (XRD), a field emission scanning electron microscope (FESEM) and a vibration sample magnetometer (VSM). The XRD show that all films have the garnet phase structure. The grain size particles measured using FESEM were between 45.08 nm to 51.58 nm, and the thickness were between 42 nm to 90 nm. The magnetic properties measured using VSM showed that result was shown with hysteresis loop. The magnetization saturation decreased from 144.26 to 2.76 emu/cm{sup 3} with the increasing substitution gallium. The substitution for y = 2.4 was shown the saturation magnetization was very low. The coercivity increased 35 to 75 Oe due the the increasing grain size.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The effect of Si content on the fracture toughness of CrAlN/Si{sub 3}N{sub 4} coatings

CrAlN/Si{sub 3}N{sub 4} nanocomposite coatings with different Si contents were deposited to understand how Si influences the microstructure and mechanical behaviour of the coatings, in particular, the fracture toughness. The coating composition, chemical bonding, microstructure, and mechanical properties were studied by energy dispersive spectroscopy, x-ray photoelectron spectroscopy, x-ray diffraction, and nanoindentation, respectively. Using a micro double cantilever beam sample, it was found that the fracture toughness of CrAlN/Si{sub 3}N{sub 4} coatings was higher than that of both the CrN and CrAlN coatings and increased with increasing Si content. Cross-sectional transmission electron microscopy suggested that this was caused by the suppression of cracking at columnar boundaries.

36 MATERIALS SCIENCE↗

The influence of A-site strontium ion in controlling the microstructure and electrical properties of P{sub 1−x}S{sub x}ZNZT ceramics

A Pb{sub 1−x}Sr{sub x}(Zn{sub 1/3}Nb{sub 2/3}){sub 0.2}(Zr{sub 0.5}Ti{sub 0.5}){sub 0.8}O{sub 3} (P{sub 1−x}S{sub x}ZNZT, 0.00 ≤ x ≤ 0.10) system was prepared through a conventional solid oxide process. Increasing addition of Sr{sup 2+} was found to induce a continuous decrease in grain size from 2.46 μm to 1.14 μm, accompanied by a phase transformation from coexisting rhombohedral and tetragonal phases to tetragonal phase only. The underlying mechanism of the evolution of dielectric and ferroelectric behavior in the P{sub 1−x}S{sub x}ZNZT ferroelectric ceramics was ascribed to the synergy between the grain size effect and the dilution of Pb-O covalency. Additionally, the grain size effect on domain wall displacement was found to be the main origin of the superior permittivity and piezoelectricity of the ceramics at intermediate grain size. The optimal electrical properties achieved for the P{sub 0.95}S{sub 0.05}ZNZT specimen at a grain size of about 1.79 μm, d{sub 33} = 465 pC/N, d{sub 33} × g{sub 33} = 11 047 × 10{sup −15} m{sup 2}/N make this material promising for multilayer energy harvesting device applications.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Microstructure and magnetic properties of ultrathin FePt granular films

FePt granular films with grain size smaller than 10 nm are promising candidates for storage media used in the next generation heat-assisted magnetic recording technology. However, FePt films show degraded magnetic properties when the grain size is reduced to this scale, which cannot be explained solely by the finite size theory. In this study, we explored the structural cause of property degradation by employing advanced electron microscopy and atomistic modeling. Structural features unique to the nanostructured FePt granular films at significantly reduced grain sizes of 2~8 nm were studied by high-resolution scanning transmission electron microscopy with geometric aberrations corrected up to the third order. Two critical structural parameters, the threshold grain size corresponding to the upper size limit of the FePt grains with zero chemical ordering and the sub-nanometer thin interfacial impurity at grain boundaries, were identified. A new atomistic model was developed to correlate these structural characteristics with key magnetic properties such as Curie temperature, saturation magnetization, magnetocrystalline anisotropy, and their grain-to-grain variation. The model shows good agreement with the experimental magnetic data and explains the gap in magnetic properties between the bulk and nanostructured FePt.

36 MATERIALS SCIENCE↗

Crystal growth, microstructure, and physical properties of SrMnSb 2

We report on the crystal and magnetic structures, magnetic, and transport properties of SrMnSb 2 single crystals grown by the self-flux method. Magnetic susceptibility measurements reveal an antiferromagnetic (AFM) transition at T N = 295(3) K. Above T N , the susceptibility slightly increases and forms a broad peak at T ~ 420 K, which is a typical feature of two-dimensional magnetic systems. Neutron diffraction measurements on single crystals confirm the previously reported C-type AFM structure below T N . Both de Haas-van Alphen (dHvA) and Shubnikov-de Haas (SdH) effects are observed in SrMnSb2 single crystals. Analysis of the oscillatory component by a Fourier transform shows that the prominent frequencies obtained by the two different techniques are practically the same within error regardless of sample size or saturated magnetic moment. Transmission electron microscopy (TEM) reveals the existence of stacking faults in the crystals, which result from a horizontal shift of Sb atomic layers suggesting possible ordering of Sb vacancies in the crystals. Increase of temperature in susceptibility measurements leads to the formation of a strong peak at T ~ 570 K that upon cooling under magnetic field the susceptibility shows a ferromagnetic transition at T C ~ 580 K. Neutron powder diffraction on crushed single-crystals does not support an FM phase above T N . Furthermore, X-ray magnetic circular dichroism (XMCD) measurements of a single crystal at the L 2,3 edge of Mn shows a signal due to induced canting of AFM moments by the applied magnetic field. All evidence strongly suggests that a chemical transformation at the surface of single crystals occurs above 500 K concurrently producing a minute amount of ferromagnetic impurity phase.

36 MATERIALS SCIENCE↗

Shrinkage, microstructure, and mechanical properties of sintered 3D-printed silica via stereolithography

Stereolithography has been used to create ceramic parts with complex geometry that is difficult to achieve with conventional fabrication techniques. Here this study used stereolithography to print silica honeycomb structures with a commercial Formlabs Form2 printer. The printed samples were sintered at different temperatures, and the print shape was retained up to 1300°C, but significant distortion from partial melting occurred at 1400°C. Higher sintering temperatures lead to more shrinkage, but it is non-uniform among directions, with the open cell plane shrinking more than the dense plane of the sample. As expected, the density of samples also increases with the sintering temperature. At higher sintering temperatures, there is an increase in cristobalite and a decrease in quartz, tridymite, and amorphous silica. Regarding mechanical properties, the out-of-plane compressive strength is approximately one order of magnitude higher than the in-plane compressive strength. When compressed along the out-of-plane direction, the samples sintered at lower temperatures surprisingly exhibit higher strength, which is explained by the micro-cracking mechanism. As expected, the samples sintered at higher temperatures display higher strength when compressed along the in-plane direction.

36 MATERIALS SCIENCE↗

Stainless Steel Microstructure and Mechanical Properties Evaluation

A nitrogen strengthened 21-6-9 stainless steel plate was spinformed into hemispherical test shapes. A battery of laboratory tests was used to characterize the hemispheres. The laboratory tests show that near the pole (axis) of a spinformed hemisphere the yield strength is the lowest because this area endures the least “cold-work” strengthening, i.e., the least deformation. The characterization indicated that stress-relief annealing spinformed stainless steel hemispheres does not degrade mechanical properties. Stress-relief annealing reduces residual stresses while maintaining relatively high mechanical properties. Full annealing completely eliminates residual stresses, but reduces yield strength by about 30%.

36 MATERIALS SCIENCE↗

Pulsed Magnetic Welding for Advanced Core and Cladding Steel

To investigate a solid-state joining method, pulsed magnetic welding (PMW), for welding the advanced core and cladding steels to be used in Generation IV systems, with a specific application for fuel pin end-plug welding. As another alternative solid state welding technique, pulsed magnetic welding (PMW) has not been extensively explored on the advanced steels. The resultant weld can be free from microstructure defects (pores, non-metallic inclusions, segregation of alloying elements). More specifically, the following objectives are to be achieved: 1. To design a suitable welding apparatus fixture, and optimize welding parameters for repeatable and acceptable joining of the fuel pin end-plug. The welding will be evaluated using tensile tests for lap joint weldments and helium leak tests for the fuel pin end-plug; 2 Investigate the microstructural and mechanical properties changes in PMW weldments of proposed advanced core and cladding alloys; 3. Simulate the irradiation effects on the PWM weldments using ion irradiation.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Microstructure and Mechanical Properties of Scaled Thermally Aged LPBF 316H SS Builds

As part of the US Department of Energy’s Advanced Materials and Manufacturing Technologies program’s mission to accelerate qualification of advanced manufacturing pathways for nuclear applications, laser powder bed fusion (LPBF) 316H stainless steel (SS) has been selected as a model system to develop a rapid code case framework. This effort directly addresses the grand challenges of (1) expanding the limited portfolio of materials currently codified for elevated-temperature nuclear structural service under Section III, Division 5 of the American Society of Mechanical Engineers’ Boiler and Pressure Vessel Code; and (2) significantly reducing qualification timelines that traditionally exceed a decade. The strategic importance of LPBF 316H lies in its immediate industrial relevance, existing data foundation from wrought 316H, and alignment with ongoing code case development for LPBF 316L. Prior work revealed accelerated precipitation of deleterious secondary phases and reduced creep ductility in as-printed LPBF 316H. Building on that prior research, FY 2025 activities focused on establishing an understanding of the key failure mechanisms of crept 316H specimens to aid in code case development and on evaluating stress relief (SR) parameters on the high-temperature performance and thermal aging induced degradation of tensile and fracture behavior in LPBF 316H.

36 MATERIALS SCIENCE↗

Wire-Based Additive Manufacturing of Stainless Steel Components

In this work three different wire-fed additive manufacturing (AM) processes were employed to evaluate differences between laser, arc, and electron beam heat sources used for high-deposition-rate AM on the order of 1 kg/h. Optimum weld and build parameters were developed independently to match the characteristics of each heat source using 308L stainless steel welding wire as the feedstock. Laser-wire AM was made with the lowest energy per unit length of weld and had the best control of the melt pool and surface finish. Wire arc-based AM had an intermediate energy per unit length of weld of approximately 5× that of the laser process, while electron beam wire AM had the highest energy per unit length of weld at approximately 10× that of the laser process. Analysis of the parts that were built included evaluation of mechanical properties and microstructures, and these properties are discussed with respect to the difference in input energy and cooling rates. Results show that all three processes build parts with properties that exceed those of annealed 304L wrought stainless steel. However, significant differences exist between the processes, and the results presented here can be used to help select the best wire-fed process for a given high-deposition-rate application.

36 MATERIALS SCIENCE↗

Microstructure and Magnetic Properties of Bulk Nanocrystalline MnAl

MnAl is a promising rare-earth free permanent magnet for technological use. We have examined the effects of consolidation by back-pressure, assisted equal channel angular extrusion processing on mechanically-milled, gas-atomized Mn-46% at. Al powder. X-ray diffraction showed both that the extruded rod consisted mostly of metastable tau phase, with some of the equilibrium gamma(2) and beta phases, and that it largely retained the as-milled nanostructure. Magnetic measurements show a coercivity of <= 4.4 kOe and a magnetization at 10 kOe of <= 40 emu/g. In addition, extrusions exhibit greater than 95% of the theoretical density. This study opens a new window in the area of bulk MnAl magnets with improved magnetic properties for technological use.

Chaturvedi, A↗