Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Low Thrust”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Wind tunnel test of model target thrust reversers for the Pratt and Whitney aircraft JT8D-100 series engines installed on a 727-200 airplane

The results of a low speed wind tunnel test of 0.046 scale model target thrust reversers installed on a 727-200 model airplane are presented. The full airplane model was mounted on a force balance, except for the nacelles and thrust reversers, which were independently mounted and isolated from it. The installation had the capability of simulating the inlet airflows and of supplying the correct proportions of primary and secondary air to the nozzles. The objectives of the test were to assess the compatibility of the thrust reversers target door design with the engine and airplane. The following measurements were made: hot gas ingestion at the nacelle inlets; model lift, drag, and pitching moment; hot gas impingement on the airplane structure; and qualitative assessment of the rudder effectiveness. The major parameters controlling hot gas ingestion were found to be thrust reverser orientation, engine power setting, and the lip height of the bottom thrust reverser doors on the side nacelles. The thrust reversers tended to increase the model lift, decrease the drag, and decrease the pitching moment.

Hambly, D.↗
NASA NTRS1948

Analysis of Effects of Inlet Pressure Losses on Performance of Axial-Flow Type Turbojet Engine

The experimentally determined performance characteristics of an axial-flow turbojet engine have been used to estimate the effects of inlet total-pressure losses on net thrust and specific fuel consumption at a constant engine speed. At low altitudes and flight Mach numbers, inlet pressure losses cause an increase in engine discharge temperature and it is possible that the maximum allowable turbine temperature maybe exceeded. An inlet absolute total-pressure loss of 10 percent will result in a thrust loss of 14 percent and a 15-percent increase in specific fuel consumption based on net thrust. At high altitudes and flight Mach numbers, choking conditions exist in the exhaust nozzle and the inlet pressure losses do not affect the discharge temperatures. Under these conditions, a 10-percent loss in inlet absolute total pressure produces a 22-percent loss in net thrust and a 16-percent increase in specific fuel consumption. If the exhaust-nozzle-outlet area is adjusted to compensate for the effect of inlet losses on discharge temperature in the nonchoking cases (low altitude and Mach numbers), the thrust and fuel consumption will be changed in a manner similar to the results obtained in the choking cases.

Sanders, Newell D↗
NASA NTRS2000

A Regeneratively-Cooled Thrust Chamber for the Fastrac Engine

This document consists of presentation slides about the development of the regeneratively cooled thrust chamber for the Fastrac engine. The Fastrac engine was originally developed to demonstrate low cost design and fabrication methods. It was intended to be used in an expendable booster. The regen thrust chamber enables a more cost efficient test program. Using the low cost design and fabrication methodology designed for the 12K regeneratively cooled chamber, the contractor designed, developed and fabricated a regeneratively cooled thrust chamber for the Fastrac engine.

Brown, Kendall↗
NASA NTRS1994

Further Research On Helicopter Tail-Boom Strakes

Two documents discuss results of additional investigations of concept introduced in "Helicopter Tail-Boom Strakes" (LAR-13233). Essence of concept that strake or pair of strakes on side of tail boom facing retreating side of main rotor of helicopter perturbs flow in such way to increase aerodynamic pressure on that side, contributing force to thrust from tail rotor. Because of force, thrust required of tail rotor for yaw control reduced. Important advantage in low-speed flight, especially in sideward flight, in which tail-rotor thrust in absence of strake sometimes insufficient.

Kelley, Henry L.↗
NASA NTRS1945

Effect of Propeller-Axis Angle of Attack on Thrust Distribution over the Propeller Disk in Relation to Wake-Survey Measurement of Thrust

Tests were made to investigate the variation of thrust distribution over the propeller disk with angle of pitch of the propeller thrust axis and to determine the disposition and the minimum number of rakes necessary to measure the propeller thrust. The tests were made at a low Mach number for a low and a high blade angle with the propeller operating at three small angles of pitch, and some of the tests were repeated at a higher Mach number. The data obtained show that, for small angles of pitch, large changes occur in the energy distribution in the wake which prohibit the use of a single survey rake for thrust measurement in flight tests and limit the use of a single rake in wind-tunnel tests. Under certain conditions, the energy distribution in the wake took on a symmetrical form and two diametrically opposed survey rakes were shown to be satisfactory for obtaining propeller thrust. (author)

Pendley, Robert E↗
NASA NTRS1974

Reversed cowl-flap thrust augmentor

Inlet mouthpiece with variable geometry improves low-speed performance of inlet (or ejector) of jet engines by use of reversed cowl-flap mechanism. Flaps can be adjusted mechanically or system can be operated with pressure taps set so pressure on inlet face is always smaller than pressure on back of inlet.

Cheng, D. Y.↗
NASA NTRS1976

Experimental and theoretical investigation of fatigue life in reusable rocket thrust chambers

During a test program to investigate low-cycle thermal fatigue, 13 rocket combustion chambers were fabricated and cyclically test fired to failure. Six oxygen-free, high-conductivity (OFHC) copper and seven Amzirc chambers were tested. The failures in the OFHC copper chambers were not typical fatigue failures but are described as creep rupture enhanced by ratcheting. The coolant channels bulged toward the chamber centerline, resulting in progressive thinning of the wall during each cycle. The failures in the Amzirc alloy chambers were caused by low-cycle thermal fatigue. The zirconium in this alloy was not evenly distributed in the chamber materials. The life that was achieved was nominally the same as would have been predicted from OFHC copper isothermal test data.

Hannum, N. P.↗
NASA NTRS1976

Experimental and theoretical investigation of fatigue life in reusable rocket thrust chambers

During a test program to investigate low-cycle thermal fatigue, 13 rocket combustion chambers were fabricated and cyclically test fired to failure. Six oxygen-free, high-conductivity (OFHC) copper and seven Amzirc chambers were tested. The chamber liners were fabricated of copper or copper alloy and contained milled coolant channels. The chambers were completed by means of an electroformed nickel closeout. The oxidant/fuel ratio for the liquid oxygen and gaseous hydrogen propellants was 6.0. The failures in the OFHC copper chambers were not typical fatigue failures but are described as creep rupture enhanced by ratcheting. The coolant channels bulged toward the chamber centerline, resulting in progressive thinning of the wall during each cycle. The failures in the Amzirc alloy chambers were caused by low-cycle thermal fatigue. The lives were much shorter than were predicted by an analytical structural analysis computer program used in conjunction with fatigue life data from isothermal test specimens, due to the uneven distribution of Zr in the chamber material.

Hannum, N. P.↗
NASA NTRS1951

Preliminary investigation of cooling-air ejector performance at pressure ratios from 1 to 10

Preliminary investigation was made of conical cooling air ejector at primary pressure ratios from 1 to 10. The cooling-air flow was maintained at zero and the resulting pressure variation in the shroud indicated pumping ability. The cooling-air flow was maintained at zero and the resulting pressure variation in the shroud indicated pumping ability. The gross thrust of the ejector and nozzle were compared. Several ratios of the spacing between the nozzle and shroud exit to the nozzle exit diameter were investigated for several shroud to nozzle exit diameter ratios. Maximum gross thrust loss occurred under conditions of zero cooling-air flow and was as much as 35 percent below nozzle jet thrust. For minimum thrust loss, ejector should be designed with as low diameter and spacing ratio as possible.

PUMPS, JET AND THRUST AUGMENTORS↗
NASA NTRS1981

Orbit transfer vehicle engine study. Phase A: Continuation (study results)

Studies included: selection of boost pump designs for low NPSH operation and generation of associated programmatic data; evaluation of OTV engine operation at intermediate thrust levels and impact on programmatics; and assessments of OTV engine operation at idle-mode thrusts under conditions experienced during aerobraking maneuvers of the ABOTV. As a result of the studies, it was recommended that the original OTV boost pump designs be used without change for low NPSH operation. Intermediate thrust operation is feasible for both the expander cycle and staged combustion cycles.

Source record↗
NASA NTRS1984

Low loss injector for Space Shuttle main engine. Center director's discretionary fund

An efficient propellant injection method to raise the Space Shuttle Main Engine (SSME) thrust and payload is discussed. Relatively large diameter injector elements with low pressure loss are recommended for the main combustion chamber and the pre-burners. Smaller losses admit more propellant flow which then raises thrust. Payload is not only gained by specific impulse but also by thrust. The chamber pressure is stabilized by selecting the proper cavity size for the injector elements while reducing the injection pressure loss which normally is kept high for stability. The rather large injector element recesses provide acoustic damping which makes baffles and acoustic absorbers unnecessary. A tenfold reduction of flow induced stresses which are rather high in the present design is shown. Relaxed tolerances, fewer elements, and better maintenance are offered. The study was conducted under a center director discretionary fund assignment.

Vonpragenau, G. L.↗
NASA NTRS2008

Design, Fabrication, and Performance of Foil Gas Thrust Bearings for Microturbomachinery Applications

A methodology for the design and construction of simple foil thrust bearings intended for parametric performance testing and low marginal costs is presented. Features drawn from a review of the open literature are discussed as they relate to bearing performance. The design of fixtures and tooling required to fabricate foil thrust bearings is presented, using conventional machining processes where possible. A prototype bearing with dimensions drawn from the literature is constructed, with all fabrication steps described. A load-deflection curve for the bearing is presented to illustrate structural stiffness characteristics. Start-top cycles are performed on the bearing at a temperature of 425 C to demonstrate early-life wear patterns. A test of bearing load capacity demonstrates useful performance when compared with data obtained from the open literature.

Dykas, Brian↗
NASA NTRS1983

The use of laterally vectored thrust to counter thrust asymmetry in a tactical jet aircraft

A nonlinear, six degree-of-freedom flight simulator for a twin engine tactical jet was built on a hybrid computer to investigate lateral vectoring of the remaining thrust component for the case of a single engine failure at low dynamic pressures. Aircraft control was provided by an automatic controller rather than a pilot, and thrust vector control was provided by an open-loop controller that deflected a vane (located on the periphery of each exhaust jet and normally streamlined for noninterference with the flow). Lateral thrust vectoring decreased peak values of lateral control deflections, eliminated the requirement for steady-state lateral aerodynamic control deflections, and decreased the amount of altitude lost for a single engine failure.

Source record↗
NASA NTRS1979

A comparison of the V/STOL handling qualities of the VAK-191B with the requirements of AGARD report 577 and MIL-F-83300

The handling qualities of the VAK-191B VTOL aircraft are compared with current V/STOL handling qualities requirements. The aircraft handling qualities were superior to other V/STOL fighter aircraft. Several deficiencies which would seriously affect shipboard V/STOL operation includes: (1) poor hovering precision; (2) inadequate mechanical control characteristics; (3) nonlinear pitch and roll response; (4) an uncommanded movement of the height control lever; (5) low pitch control sensitivity; (6) excessive dihedral effect; and (7) inadequate overall thrust response. The attitude command control system resulted on reduced pilot workload during hover and low speed flight.

Anderson, S. B.↗
NASA NTRS2014

Mode Transitions in Magnetically Shielded Hall Effect Thrusters

A mode transition study is conducted in magnetically shielded thrusters where the magnetic field magnitude is varied to induce mode transitions. Three different oscillatory modes are identified with the 20-kW NASA-300MS-2 and the 6-kW H6MS: Mode 1) global mode similar to unshielded thrusters at low magnetic fields, Mode 2) cathode oscillations at nominal magnetic fields, and Mode 3) combined spoke, cathode and breathing mode oscillations at high magnetic fields. Mode 1 exhibits large amplitude, low frequency (1-10 kHz), breathing mode type oscillations where discharge current mean value and oscillation amplitude peak. The mean discharge current is minimized while thrust-to-power and anode efficiency are maximized in Mode 2, where higher frequency (50-90 kHz), low amplitude, cathode oscillations dominate. Thrust is maximized in Mode 3 and decreases by 5-6% with decreasing magnetic field strength. The presence or absence of spokes and strong cathode oscillations do not affect each other or discharge current. Similar to unshielded thrusters, mode transitions and plasma oscillations affect magnetically shielded thruster performance and should be characterized during system development.

Ground Tests↗
NASA NTRS2014

General Aviation Flight Test of Advanced Operations Enabled by Synthetic Vision

A flight test was performed to compare the use of three advanced primary flight and navigation display concepts to a baseline, round-dial concept to assess the potential for advanced operations. The displays were evaluated during visual and instrument approach procedures including an advanced instrument approach resembling a visual airport traffic pattern. Nineteen pilots from three pilot groups, reflecting the diverse piloting skills of the General Aviation pilot population, served as evaluation subjects. The experiment had two thrusts: 1) an examination of the capabilities of low-time (i.e., <400 hours), non-instrument-rated pilots to perform nominal instrument approaches, and 2) an exploration of potential advanced Visual Meteorological Conditions (VMC)-like approaches in Instrument Meteorological Conditions (IMC). Within this context, advanced display concepts are considered to include integrated navigation and primary flight displays with either aircraft attitude flight directors or Highway In The Sky (HITS) guidance with and without a synthetic depiction of the external visuals (i.e., synthetic vision). Relative to the first thrust, the results indicate that using an advanced display concept, as tested herein, low-time, non-instrument-rated pilots can exhibit flight-technical performance, subjective workload and situation awareness ratings as good as or better than high-time Instrument Flight Rules (IFR)-rated pilots using Baseline Round Dials for a nominal IMC approach. For the second thrust, the results indicate advanced VMC-like approaches are feasible in IMC, for all pilot groups tested for only the Synthetic Vision System (SVS) advanced display concept.

Glaab, Louis J.↗
DOE OSTI2024

LUCID Thrust 1 - Dataset Identification and Biodata Catalog Creation

The LUCID DOE consortium, part of the Department of Energy’s Biological and Environmental Research (BER) program, advances Low Dose Radiation (LDR) research through multidisciplinary efforts across seven key thrusts. This document focuses on Thrust 1, which centers on the creation of curated multimodal population health datasets and supports broader efforts within the LUCID program, including AI-based hypothesis generation, experimental design, and the study of LDR-induced health risks. Specifically, it describes the identification and cataloging of Thrust 1’s curated LDR datasets and biodata, emphasizing their critical role in supporting various research thrusts within the consortium, with potential applications in healthcare and public policy. In addition, the document includes an evaluation of three Large Language Models (LLMs)—GPT-4, SOLAR-10B, and Mixtral-8x7B—based on their ability to extract features from 25 LDR studies. The results indicate that GPT-4 performed the best, while Mixtral-8x7B demonstrated limited knowledge. Overall, this work advances understanding in radiation protection, risk assessment, and medical treatments, while providing valuable resources for researchers, educators, and policymakers.

63 RADIATION, THERMAL, AND OTHER ENVIRON. POLLUTAN↗