Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Low Temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57

Low temperature aluminum nitride thin films for sensory applications

A low-temperature sputter deposition process for the synthesis of aluminum nitride (AlN) thin films that is attractive for applications with a limited temperature budget is presented. Influence of the reactive gas concentration, plasma treatment of the nucleation surface and film thickness on the microstructural, piezoelectric and dielectric properties of AlN is investigated. An improved crystal quality with respect to the increased film thickness was observed; where full width at half maximum (FWHM) of the AlN films decreased from 2.88 ± 0.16° down to 1.25 ± 0.07° and the effective longitudinal piezoelectric coefficient (d{sub 33,f}) increased from 2.30 ± 0.32 pm/V up to 5.57 ± 0.34 pm/V for film thicknesses in the range of 30 nm to 2 μm. Dielectric loss angle (tan δ) decreased from 0.626% ± 0.005% to 0.025% ± 0.011% for the same thickness range. The average relative permittivity (ε{sub r}) was calculated as 10.4 ± 0.05. An almost constant transversal piezoelectric coefficient (|e{sub 31,f}|) of 1.39 ± 0.01 C/m{sup 2} was measured for samples in the range of 0.5 μm to 2 μm. Transmission electron microscopy (TEM) investigations performed on thin (100 nm) and thick (1.6 μm) films revealed an (002) oriented AlN nucleation and growth starting directly from the AlN-Pt interface independent of the film thickness and exhibit comparable quality with the state-of-the-art AlN thin films sputtered at much higher substrate temperatures.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Instability-enhanced transport in low temperature magnetized plasma

It is shown that the transport in low temperature, collisional, bound plasma is enhanced by instabilities at a high magnetic field. While the magnetic field confines the electrons in a stable plasma, the instability completely destroys the confinement such that the transport becomes independent of the magnetic field in the highly magnetized limit. Finally, an analytical expression of the instability-enhanced collision frequency is proposed, based on a magnetic field independent edge-to-center density ratio.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The substructure and luminescence of low-temperature AlGaAs/GaAs(100) heterostructures

The substructure and luminescence of low-temperature epitaxial AlGaAs alloys are studied by Raman spectroscopy and photoluminescence spectroscopy. It is shown that the experimental data obtained in the study are consistent with the results of the previous structural and optical study. The assumption that, at high concentrations of carbon acceptors, the acceptor atoms concentrate at lattice defects of the AlGaAs crystal alloys to form carbon nanocrystals is confirmed.

36 MATERIALS SCIENCE↗

Low-temperature bonding of temperature-resistant electronic connections

Bonding of flat metal surfaces utilizes low temperature melting intermediate material, pulse heating, and pressure application to produce strong, electrically conductive bond resistant to melting at temperatures well above melting point of intermediate material. Little or no intermediate material remains at the interface.

Peluso, R. F.↗

Low-temperature Brayton radiator performance in a variable-sink-temperature environment

An analysis of the performance of a low-temperature Brayton space radiator is presented. The cylindrical radiator with circumferential tubes was subjected to an equivalent sink temperature environment that varied along the fluid flow path. The radiator performance, as measured by fluid outlet temperature, was found to be dependent on the orbital position and the location of the radiator inlet relative to the sink temperature environment. An approximate dynamic analysis of sun-shade variations in performance is included.

Bien, D. B.↗

Development of a low temperature phase change material package

Test data obtained for a low temperature phase change material (PCM) canisters are presented. The canister was designed to provide up to 30 w-hrs of storage capacity at approximately -90 C with an overall thermal conductance which is greater than 8 w/deg C. N-heptane which is an n-paraffin and has a -90.6 C freezing point was used as the working fluid. The canister was fabricated from aluminum and has an aluminum honeycomb core. Its void volume permits service temperatures up to 70 C. Results obtained from component and system's tests indicate well defined melting and freezing points which are repeatable and within 1 C of each other. Subcooling effects are less than 0.5 C and are essentially negligible. Measured storage capacities are within 94 to 88% the theoretical.

Brennan, P. J.↗

Characterization of Superhydrophobic Surfaces for Anti-icing in a Low-Temperature Wind Tunnel

In this study, a closed loop low-temperature wind tunnel was custom-built and uniquely used to investigate the anti-icing mechanism of superhydrophobic surfaces in regulated flow velocities, temperatures, humidity, and water moisture particle sizes. Silica nanoparticle-based hydrophobic coatings were tested as superhydrophobic surface models. During tests, images of ice formation were captured by a camera and used for analysis of ice morphology. Prior to and after wind tunnel testing, apparent contact angles of water sessile droplets on samples were measured by a contact angle meter to check degradation of surface superhydrophobicity. A simple peel test was also performed to estimate adhesion of ice on the surfaces. When compared to an untreated sample, superhydrophobic surfaces inhibited initial ice formation. After a period of time, random droplet strikes attached to the superhydrophobic surfaces and started to coalesce with previously deposited ice droplets. These sites appear as mounds of accreted ice across the surface. The appearance of the ice formations on the superhydrophobic samples is white rather than transparent, and is due to trapped air. These ice formations resemble soft rime ice rather than the transparent glaze ice seen on the untreated sample. Compared to untreated surfaces, the icing film formed on superhydrophobic surfaces was easy to peel off by shear flows.

36 MATERIALS SCIENCE↗

Enhanced High- and Low-Temperature Performance of NOx Reduction Catalyst Materials

In this annual CRADA program report, we will briefly highlight results from our recent studies of the stability of candidate K-based high temperature NSR materials, and comparative studies of low temperature performance of SSZ-13 and SAPO-34 CHA catalysts; in particular, recent results comparing Fe- and Cu-based CHA materials.

Environmental Molecular Sciences Laboratory↗

Methods for producing electrochromic films by low temperature condensation of polyoxometalates

Described are electrochromic films produced by low temperature condensation of polyoxometalates and applications thereof. A method of producing an electrochromic film includes depositing a polyoxometalate (POM) solution on a substrate to form a POM film. The POM solution includes anionic POM clusters and counter ions, and may be doped with near-infrared plasmonic nanocrystals. The film is chemically cured using an acid to condense the POM clusters within the POM film. Another method of producing an electrochromic film includes electrochemical deposition and condensation of POM clusters.

36 MATERIALS SCIENCE↗

Low-temperature formation of polycyclic aromatic hydrocarbons in Titan’s atmosphere

The detection of benzene in Titan’s atmosphere led to the emergence of polycyclic aromatic hydrocarbons (PAHs) as potential nucleation agents triggering the growth of Titan’s orange-brownish haze layers. However, the fundamental mechanisms leading to the formation of PAHs in Titan’s low-temperature atmosphere have remained elusive. We provide persuasive evidence through laboratory experiments and computations that prototype PAHs like anthracene and phenanthrene (C 14 H 10 ) are synthesized via barrierless reactions involving naphthyl radicals (C 10 H 7 •) with vinylacetylene (CH 2 =CH–C≡CH) in low-temperature environments. These elementary reactions are rapid, have no entrance barriers, and synthesize anthracene and phenanthrene via van der Waals complexes and submerged barriers. This facile route to anthracene and phenanthrene—potential building blocks to complex PAHs and aerosols in Titan—signifies a critical shift in the perception that PAHs can only be formed under high-temperature conditions, providing a detailed understanding of the chemistry of Titan’s atmosphere by untangling elementary reactions on the most fundamental level.

79 ASTRONOMY AND ASTROPHYSICS↗

Phase degradation in B x Ga 1–x N films grown at low temperature by metalorganic vapor phase epitaxy

Using metalorganic vapor phase epitaxy, a comprehensive study of B x Ga 1-x N growth on GaN and AlN templates is described. BGaN growth at high-temperature and high-pressure results in rough surfaces and poor boron incorporation efficiency, while growth at low-temperature and low-pressure (750–900 °C and 20 Torr) using nitrogen carrier gas results in improved surface morphology and boron incorporation up to ~7.4% as determined by nuclear reaction analysis. However, further structural analysis by transmission electron microscopy and x-ray pole figures points to severe degradation of the high boron composition films, into a twinned cubic structure with a high density of stacking faults and little or no room temperature photoluminescence emission. Films with <1% triethylboron (TEB) flow show more intense, narrower x-ray diffraction peaks, near-band-edge photoluminescence emission at ~362 nm, and primarily wurtzite-phase structure in the x-ray pole figures. For films with >1% TEB flow, the crystal structure becomes dominated by the cubic phase. As a result, only when the TEB flow is zero (pure GaN), does the cubic phase entirely disappear from the x-ray pole figure, suggesting that under these growth conditions even very low boron compositions lead to mixed crystalline phases.

36 MATERIALS SCIENCE↗

Low temperature magnetocaloric effect in polycrystalline BiFeO{sub 3} ceramics

We report on the structural, thermal, and magnetic properties of polycrystalline BiFeO{sub 3} synthesized by sol-gel route. Powder x-ray diffraction data of the BiFeO{sub 3} sample was refined with rhombohedral structure with space group R3c. Magnetization and coercive field measurements showed weak ferromagnetic nature below 10 K. We also investigated the low temperature magnetocaloric effect in polycrystalline BiFeO{sub 3} ceramics. The anomalies observed in the magnetic entropy change of the BiFeO{sub 3} ceramics were close to that of low temperature phase transitions. The combined relative errors in the magnetic entropy change are found to vary from 4% to 15% with increase in temperature.

36 MATERIALS SCIENCE↗

Stomatal conductance, not biochemistry, drives low temperature acclimation of photosynthesis in Populus balsamifera , regardless of nitrogen availability

Low temperature thermal acclimation may require adjustments to nitrogen and water use to sustain photosynthesis due to slow enzyme functioning and high-water viscosity. However, understanding of photosynthetic acclimation to temperatures below 11°C is limited. Here, we acclimated Populus balsamifera to 6 °C and 10 °C (6A and 10A, respectively) and provided the trees with either high or low N fertilizer. We measured net CO 2 assimilation rates (A net ), stomatal conductance (g s ), maximum rates of Rubisco carboxylation (V cmax ) and electron transport (J max ), and dark respiration (R d ) at leaf temperatures of 2, 6, 10, 14 and 18 °C, along with leaf N concentrations. The 10A trees had higher A net than the 6A trees at warmer leaf temperatures, which was correlated with higher g s in the 10A trees. The instantaneous temperature responses of V cmax , J max and R d were similar for trees from both acclimation temperatures. While soil N availability increased leaf N concentrations, this had no effect on acclimation of photosynthesis or respiration. Our results indicate that acclimation below 11°C occurred primarily through changes in stomatal conductance, not photosynthetic biochemistry, and was unaffected by short-term N supply. Thermal acclimation of stomatal conductance should therefore be a priority for future carbon cycle model development.

54 ENVIRONMENTAL SCIENCES↗

Thermomechanical fatigue resistance of low temperature solder for multiwire interconnects in photovoltaic modules

Novel interconnect technologies leveraging low melting temperature solders, such as multiwire interconnects, are being deployed in photovoltaic (PV) modules for improved reliability through interconnect redundancy and lower thermal loads during interconnection and lamination. However, the equivalency of standardized accelerated testing to field conditions has not yet been established for these emerging technologies. In this study, the thermomechanical fatigue resistance of low temperature solder alloys is investigated and compared to that of conventional SnPb to assess the acceleration behavior of these alloys. While InSn is shown to have sufficient thermomechanical fatigue resistance on the order of that of SnPb, these results indicate Sn–Bi alloys may have poor thermomechanical fatigue resistance at field conditions. The results also show that Sn–Bi alloys have thermal cycling acceleration factors of less than one. This indicates that the standardized accelerated thermal cycling test, such as that in IEC 61215, will produce misleading results for Sn–Bi alloys and that unique testing is required for this PV module architecture. Though accelerated thermal cycling may be a meaningful qualification test for SnPb solder joints, these results suggest that mechanical loading may be a more appropriate test for Sn–Bi multiwire interconnects. This is due to the distinct processing and geometry of multiwire interconnects which may allow for mechanical, rather than strictly metallurgical interconnections.

14 SOLAR ENERGY↗

Low-Temperature Production of Cosmic Grains Analogs From Gas-Phase Molecular Precursors with the NASA Ames' COSmIC Facility

Complex carbon molecules and ions are ubiquitous in space and form the building blocks of carbonaceous cosmic dust grains, ultimately contributing to the formation of planets. Here, we report the first experimental investigations of the low temperature chemical pathways leading to the production of cosmic grain analogs from gas phase molecular precursors in order to better understand the evolution of cosmic carbon. The experiments were performed using the COsmic SImulation Chamber (COSmIC) to generate and characterize grains formed from gas phase precursors under controlled conditions representative of astrophysical environments [1]. Using COSmIC, it is possible to investigate the evolution of cosmic carbon from the formation of neutral and ionized gas phase hydrocarbons and PAHs [2], to carbon grains [3, 4]. This is achieved by using a discharge nozzle to (1) produce an adiabatic jet expansion and cool down Ar-hydrocarbon/PAH gas mixtures to astrophysically relevant temperature (150 K) before inducing chemistry by generating a plasma discharge in the stream of the expansion. This plasma-induced chemistry results in the formation of complex molecules and solid particles, analogs of cosmic grains. Solid grains are produced in-situ in the plasma expansion, carried by the accelerated gas in the expansion, and collected on substrates placed a few centimeters downstream of the electrodes. The results of a preliminary solid phase ex-situ analysis of cosmic grain analogs produced at low temperature in COSmIC from gas mixtures including molecular precursors of cosmic carbon grains, i.e., such as CH4 and C2H2 found in circumstellar ejecta of late C stars [3] as well as PAHs ubiquitously detected in IR emission bands seen in galactic and extragalactic environments [4] will be discussed. Scanning Electron Microscopy imaging was used to provide insight on the morphology and growth structure of the grains produced in COSmIC, and to investigate how the precursors used to produce the grains affect these parameters [3]. Laser desorption mass spectrometry was used to identify the molecules making up the main structures within the condensed grains [4]. NIR to FIR optical properties are characterized to provide critical information (functional groups, optical constants) to the scientific community, for use in radiative transfer models in particular, and to help decipher and enhance the return data from space observations.

F. Salama↗

Advanced Low-Temperature Chlorination of Zirconium

Recovery of Zr from nuclear fuel is of high interest because the Zr cladding material comprises up to 50% of the high-level radioactive waste (HLW) that requires disposition. An ideal Zr-recovery process would not only recover the bulk Zr from the fuel or cladding but would also provide decontamination from the components that give rise to the HLW designation. A simplified decontamination pathway providing recovered Zr in compliance with low-level radioactive waste acceptance criteria could significantly reduce the burden of HLW requiring geologic disposition. A newly developed advanced low-temperature chlorination process presents an opportunity to recover a ZrCl4 product that is effectively decontaminated from the elements of concern. This advanced low-temperature chlorination process uses a mixture of the sulfur-containing chlorination compounds sulfur monochloride (S 2 Cl 2 ) and thionyl chloride (SOCl 2 ).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗