Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “INFLATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57

Structural Considerations of Inflatable Reentry Vehicles

The state of the design art for inflated structures applicable to reentry vehicles is discussed. Included are material properties, calculations of buckling and collapse loads, and calculations of deflections and vibration frequencies. A new theory for the analysis of inflated plates is presented and compared with experiment.

Leonard, Robert W.↗

Skin Stresses in an Inflated Sphere During Impact

An analysis is made of the stresses in the skin of an inflated nonstretchable sphere during normal, nonrotating impact with a hard flat surface, assuming infinite modulus of elasticity in the skin and infinite propagation speed of stress waves. The analysis is further applied to the study of the inflated sphere landing vehicle containing a payload suspended at the center. Curves are presented showing the stress distributions during impact for cases corresponding to those calculated in previous reports in which the impact motion and payload landing performance capabilities of the landing vehicle have been studied. It is found, assuming the force from the payload-suspension cords to be distributed continuously on the skin, that is, neglecting stress concentrations,that the skin stresses along a meridian are reduced by the presence of the suspended payload during impact, but that the maximum values of skin stress normal to a meridian are little affected.

Martin, E. Dale↗

Dynamic Testing of an Inflatable Structure Under Thermal Vacuum Conditions

The Marshall Space Flight Center's Space Transportation Programs Office is responsible for the development and demonstration of advanced launch vehicle and propulsion technologies. One of these advanced propulsion concepts being pursued is solar thermal propulsion. This concept employs a concentrated beam of sunlight to heat a working fluid within a solar thermal engine. Expansion of the fluid would provide thrust at an increased specific impulse. One way to concentrate the sun's light to a specific point in the engine cavity is to use a fresnel lens that is supported by an inflatable structure. Such propulsion systems could provide an inexpensive way of transferring and maintaining satellites to upper stage orbit trajectories. This paper describes the test hardware, procedures, and non-contacting measurement methodologies used to determine the modal characteristics of an inflatable concentrator under the thermal-vacuum conditions of space. These characteristics were necessary to identify for validation of a finite element model to be used for developing the spacecraft's pointing and control system.

Engberg, Robert↗

Structural Modeling of a Five-Meter Thin Film Inflatable Antenna/Concentrator With Rigidized Support Struts

Dynamic characterization of a non-rigidized thin film inflatable antenna/solar concentrator structure with rigidized composite support struts is described in detail. A two-step finite element modeling approach in MSC/NASTRAN is utilized, consisting of: (1) a nonlinear static pressurization procedure used to obtain the updated stiffness matrix, and (2) a modal "restart" eigen solution that uses the modified stiffness matrix. Unique problems encountered in modeling of this large 5-m lightweight inflatable are identified, including considerable difficulty in obtaining convergence in the nonlinear pressurization solution. It was found that the extremely thin polyimide film material (.001 in or I mil) presents tremendous problems in obtaining a converged solution when internal pressure loading is applied. It was concluded that the ratios of film thickness to other geometric dimensions such as torus cross-sectional and ring diameter and lenticular diameter are the critical parameters for convergence of the pressurization procedure. Comparison of finite element predictions for frequency and mode shapes with experimental results indicated reasonable agreement considering the complexity of the structure, the film-to-air interaction, and the nonlinear material properties of the film. It was also concluded that analysis should be done using different finite element to codes to determine if a more robust and stable solution can be obtained.

Smalley, Kurt B.↗

Pressure Distribution in Inflated Lava Flows

There has been considerable debate regarding the role of inflation in terrestrial and planetary lava flow emplacement. We used a tumuli growth model to estimate the pressure within Hawaiian lava flows to better understand inflation processes. Additional information is contained in the original extended abstract.

Anderson, S. W.↗

Pathfinder Photogrammetry Research for Ultra-Lightweight and Inflatable Space Structures

The defining characteristic of ultra-lightweight and inflatable space structures is that they are both very large and very low mass. This makes standard contacting methods of measurement (e.g. attaching accelerometers) impractical because the dynamics of the structure would be changed by the mass of the contacting instrument. Optical measurements are therefore more appropriate. Photogrammetry is a leading candidate for the optical analysis of gossamer structures because it allows for the measurement of a large number of points, is amenable to time sequences, and offers the potential for a high degree of accuracy. The purpose of this thesis is to develop the methodology and determine the effectiveness of a photogrammetry system in measuring ultra-lightweight and inflatable space structures. The results of this thesis will be considered in the design of an automated photogrammetry system for the l6m-diameter vacuum chamber at the NASA Langley Research Center.

Giersch, Louis Roy Miller↗

Deployment, Foam Rigidization, and Structural Characterization of Inflatable Thin-Film Booms

Detailed investigation of the construction, packaging/deployment, foam rigidization, and structural characterization of polyimide film inflatable booms is described. These structures have considerable potential for use in space with solar concentrators, solar sails, space power systems including solar arrays, and other future missions. Numerous thin-film booms or struts were successfully constructed, inflated, injected with foam, and rigidized. Both solid-section and annular test articles were fabricated, using Kapton polyimide film, various adhesives, Styrofoam end plugs, and polyurethane pressurized foam. Numerous inflation/deployment experiments were conducted and compared to computer simulations using the MSC/DYTRAN code. Finite element models were developed for several foam-rigidized struts and compared to model test results. Several problems encountered in the construction, deployment, and foam injection/rigidization process are described. Areas of difficulty included inadequate adhesive strength, cracking of the film arid leakage, excessive bending of the structure during deployment, problems with foam distribution and curing properties, and control of foam leakage following injection into the structure. Many of these problems were overcome in the course of the research.

Schnell, Andrew R.↗

Statistical Distribution of Inflation on Lava Flows: Analysis of Flow Surfaces on Earth and Mars

The surface morphology of a lava flow results from processes that take place during the emplacement of the flow. Certain types of features, such as tumuli, lava rises and lava rise pits, are indicators of flow inflation or endogenous growth of a lava flow. Tumuli in particular have been identified as possible indicators of tube location, indicating that their distribution on the surface of a lava flow is a junction of the internal pathways of lava present during flow emplacement. However, the distribution of tumuli on lava flows has not been examined in a statistically thorough manner. In order to more rigorously examine the distribution of tumuli on a lava flow, we examined a discrete flow lobe with numerous lava rises and tumuli on the 1969 - 1974 Mauna Ulu flow at Kilauea, Hawaii. The lobe is located in the distal portion of the flow below Holei Pali, which is characterized by hummocky pahoehoe flows emplaced from tubes. We chose this flow due to its discrete nature allowing complete mapping of surface morphologies, well-defined boundaries, well-constrained emplacement parameters, and known flow thicknesses. In addition, tube locations for this Mauna Ulu flow were mapped by Holcomb (1976) during flow emplacement. We also examine the distribution of tumuli on the distal portion of the hummocky Thrainsskjoldur flow field provided by Rossi and Gudmundsson (1996). Analysis of the Mauna Ulu and Thrainsskjoldur flow lobes and the availability of high-resolution MOC images motivated us to look for possible tumuli-dominated flow lobes on the surface of Mars. We identified a MOC image of a lava flow south of Elysium Mons with features morphologically similar to tumuli. The flow is characterized by raised elliptical to circular mounds, some with axial cracks, that are similar in size to the tumuli measured on Earth. One potential avenue of determining whether they are tumuli is to look at the spatial distribution to see if any patterns similar to those of tumuli-dominated terrestrial flows can be identified. Since tumuli form by the injection of lava beneath a crust, the distribution of tumuli on a flow should represent the distribution of thermally preferred pathways beneath the surface of the crust. That distribution of thermally preferred pathways may be a function of the evolution of a basaltic lava flow. As a longer-lived flow evolves, initially broad thermally preferred pathways would evolve to narrower, more well-defined tube-like pathways. The final flow morphology clearly preserves the growth of the flow over time, with inflation features indicating pathways that were not necessarily contemporaneously active. Here, we test using statistical analysis whether this final flow morphology produces distinct distributions that can be used to readily determine the distribution of thermally preferred pathways beneath the surface of the crust.

Glazel, L. S.↗

Nonlinear Pressurization and Modal Analysis Procedure for Dynamic Modeling of Inflatable Structures

An introduction and set of guidelines for finite element dynamic modeling of nonrigidized inflatable structures is provided. A two-step approach is presented, involving 1) nonlinear static pressurization of the structure and updating of the stiffness matrix and 2) hear normal modes analysis using the updated stiffness. Advantages of this approach are that it provides physical realism in modeling of pressure stiffening, and it maintains the analytical convenience of a standard bear eigensolution once the stiffness has been modified. Demonstration of the approach is accomplished through the creation and test verification of an inflated cylinder model using a large commercial finite element code. Good frequency and mode shape comparisons are obtained with test data and previous modeling efforts, verifying the accuracy of the technique. Problems encountered in the application of the approach, as well as their solutions, are discussed in detail.

Smalley, Kurt B.↗

Magnetic Dipole Inflation with Cascaded ARC and Applications to Mini-Magnetospheric Plasma Propulsion

Mini-Magnetospheric Plasma Propulsion (M2P2) seeks to create a plasma-inflated magnetic bubble capable of intercepting significant thrust from the solar wind for the purposes of high speed, high efficiency spacecraft propulsion. Previous laboratory experiments into the M2P2 concept have primarily used helicon plasma sources to inflate the dipole magnetic field. The work presented here uses an alternative plasma source, the cascaded arc, in a geometry similar to that used in previous helicon experiments. Time resolved measurements of the equatorial plasma density have been conducted and the results are discussed. The equatorial plasma density transitions from an initially asymmetric configuration early in the shot to a quasisymmetric configuration during plasma production, and then returns to an asymmetric configuration when the source is shut off. The exact reasons for these changes in configuration are unknown, but convection of the loaded flux tube is suspected. The diffusion time was found to be an order of magnitude longer than the Bohm diffusion time for the period of time after the plasma source was shut off. The data collected indicate the plasma has an electron temperature of approximately 11 eV, an order of magnitude hotter than plasmas generated by cascaded arcs operating under different conditions. In addition, indirect evidence suggests that the plasma has a beta of order unity in the source region.

Giersch, L.↗

A Design Study of the Inflated Sphere Landing Vehicle, Including the Landing Performance and the Effects of Deviations from Design Conditions

The impact motion of the inflated sphere landing vehicle with a payload centrally supported from the spherical skin by numerous cords has been determined on the assumption of uniform isentropic gas compression during impact. The landing capabilities are determined for a system containing suspension cords of constant cross section. The effects of deviations in impact velocity and initial gas temperature from the design conditions are studied. Also discussed are the effects of errors in the time at which the skin is ruptured. These studies indicate how the design parameters should be chosen to insure reliability of the landing system. Calculations have been made and results are presented for a sphere inflated with hydrogen, landing on the moon in the absence of an atmosphere. The results are presented for one value of the skin-strength parameter.

Martin, E. Dale↗

Optical Strain Measurement of an Inflated Cylinder using Photogrammetry with Application to Scientific Balloons

A study is presented using photogrammetry to measure the biaxial strain in an inflated cylinder. Two cylinders constructed from polyethylene and each approximately 222 mm in diameter and 930 mm in length were studied. The first had a 0.038 mm wall thickness while the second had a 0.02 mm wall thickness. The cylinders were inflated to a maximum pressure of 1379 Pa. The strain was determined from data collected from 60 retro-reflective targets arranged in a 12 x 5 grid. The uncertainty of the measurement system was determined to be 0.08, 0.04 and 0.06 mm in the x, y, and z directions respectively. The hoop and meridional strains determined from displacement data were compared to values obtained from a finite element analysis of a related proxy problem. The predicted hoop strains showed good agreement over the entire range of pressures while the meridional strains showed good agreement at the lower pressures.

Blandino, Joseph R.↗

Development and Ground Testing of a Compactly Stowed Scalable Inflatably Deployed Solar Sail

This paper discusses the solar sail design and outlines the interim accomplishments to advance the technology readiness level (TRL) of the subsystem from 3 toward a technology readiness level of 6 in 2005. Under Phase II of the program many component test articles have been fabricated and tested successfully. Most notably an unprecedented section of the conically deployed rigidizable sail support beam, the heart of the inflatable rigidizable structure, has been deployed and tested in the NASA Goddard thermal vacuum chamber with good results. The development testing validated the beam packaging and deployment. The inflatable conically deployed, Sub Tg rigidizable beam technology is now in the TRL 5-6 range. The fabricated masses and structural test results of our beam components have met predictions and no changes to the mass estimates or design assumptions have been identified adding great credibility to the design. Several quadrants of the Mylar sail have also been fabricated and successfully deployed validating our design, manufacturing, and deployment techniques.

Lichodziejewski, David↗

A Dual-polarized Microstrip Subarray Antenna for an Inflatable L-band Synthetic Aperture Radar

Inflatable technology has been identified as a potential solution to the problem of achieving small mass, high packaging efficiency, and reliable deployment for future NASA spaceborne synthetic aperture radar (SAR) antennas. Presently, there exists a requirement for a dual-polarized L-band SAR antenna with an aperture size of 10m x 3m, a center frequency of 1.25GHz, a bandwidth of 80MHz, electronic beam scanning, and a mass of less than 100kg. The work presented below is part of the ongoing effort to develop such an inflatable antenna array.

Zawadzki, Mark↗

Inflatable Habitats Technology Development

For many years inflatable structures have been theorized for use as satellite dishes, deployable arrays and human habitats. They fall into human-rated and non-human rated structures. As such the structural design requirements and safety redundancy are much different. This paper will discuss the Habitat and Surface Construction Technology that would support the development of Mars greenhouses as well as habitats. This paper will briefly describe the ISS TransHab architectural design and structural testing for the proposed as a habitation module for the International Space Station. It will also discuss inflatable greenhouse design considerations and examples.

Kennedy, Kriss J.↗

Inflatable Solar Thermal Concentrator Delivered

Space-based solar thermal power systems are very appealing as a space power source because they generate power efficiently. However, solar thermal (dynamic) systems currently incorporate rigid concentrators that are relatively heavy and require significant packaging volume and robust deployment schemes. In many ways, these requirements make these systems less appealing than photovoltaic systems. As an alternative to solar thermal power systems with rigid concentrators, solar thermal power systems with thin film inflation-deployed concentrators have low cost, are lightweight, and are efficiently packaged and deployed. Not only are inflatable concentrators suitable for low Earth orbit and geosynchronous orbit applications, but they can be utilized in deep space missions to concentrate solar energy to high-efficiency solar cells.

Tolbert, Carol M.↗

Biaxial Testing of High-Strength Fabric Improves Design of Inflatable Radar Domes

Large radar installations around the globe continuously watch the skies, unobtrusively providing security to the United States; these systems have been in active use for the past 50 years. Often situated in extreme environments, the radar dishes require shielding from the harsh elements. Air-inflated domes (over 100 ft in diameter) are one structure of choice for providing this essential protection. The radomes are constructed from highstrength fabric that is strong enough to withstand the inflation pressure, high winds, and other environmental loads, yet transparent to the microwave signal to allow precise radar mapping. This fabric is woven from glass fibers for high strength and embedded in a polytetrafluoroethylene resin matrix, akin to the nonstick coatings used on cookware.

Krause, David L.↗

AEROELASTIC SIMULATION TOOL FOR INFLATABLE BALLUTE AEROCAPTURE

A multidisciplinary analysis tool is under development for predicting the impact of aeroelastic effects on the functionality of inflatable ballute aeroassist vehicles in both the continuum and rarefied flow regimes. High-fidelity modules for continuum and rarefied aerodynamics, structural dynamics, heat transfer, and computational grid deformation are coupled in an integrated multi-physics, multi-disciplinary computing environment. This flexible and extensible approach allows the integration of state-of-the-art, stand-alone NASA and industry leading continuum and rarefied flow solvers and structural analysis codes into a computing environment in which the modules can run concurrently with synchronized data transfer. Coupled fluid-structure continuum flow demonstrations were conducted on a clamped ballute configuration. The feasibility of implementing a DSMC flow solver in the simulation framework was demonstrated, and loosely coupled rarefied flow aeroelastic demonstrations were performed. A NASA and industry technology survey identified CFD, DSMC and structural analysis codes capable of modeling non-linear shape and material response of thin-film inflated aeroshells. The simulation technology will find direct and immediate applications with NASA and industry in ongoing aerocapture technology development programs.

Liever, P. A.↗