Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “HEAT TREATMENTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Final Scientific/Technical Report Rapid Design and Manufacturing of High-Performance Materials for Turbine Blades

This research demonstrated the concept of carbide precipitation-strengthened refractory high entropy alloys (RHEA). The advantage of a precipitation strengthened alloy is all phases are in thermodynamic equilibrium promoting microstructural stability, and consequently retention of properties at elevated temperatures. Additionally, as with any precipitation strengthened – or age hardened alloy, components can be heat-treated after manufacturing to manipulate the microstructure and optimize properties for performance. This is an advantage of the precipitation strengthened alloys over composites and ceramics materials, where the microstructure and properties are essentially fixed upon the initial materials manufacturing stage. High throughput (HT), multi-scale computer modeling was used to identifying novel RHEA compositions with desired characteristics needed for precipitation strengthening. The results showed that carbides precipitated and consequently, the strength of the alloys (measured in compression) increased after heat-treatment, which is the desired effect. The project also demonstrated the feasibility of producing articles from RHEA by additive manufacturing (AM).

36 MATERIALS SCIENCE↗
DOE OSTI2024

Transfer of EP and Doping Technology for PIP-II HB650 Cavities from Fermilab to Industry

Fermilab has optimized the surface processing conditions for PIP-II high beta 650 MHz cavities. This encompasses conditions for bulk electropolishing, heat treatment, nitrogen doping, post-doping final electropolishing, and post-processing surface rinsing. The technology has been effectively transitioned to industry. This paper highlights the efforts made to fine-tune the process and to smoothly share them with the partner labs and an associated vendor.

Chouhan, V.↗
DOE OSTI2024

In-situ and ex-situ characterization of irradiated AM materials

This study investigates the irradiation performance of laser powder bed fusion (LPBF) 316L and 316H stainless steels (SS), and their wrought counterparts. While LPBF 316L has been more studied, LPBF 316H is relatively new, with little prior data on its irradiation behavior. The research involved fabricating, preparing, irradiating, and characterizing six materials: LPBF 316L (two variants), LPBF 316H (two variants), and wrought 316L and 316H. LPBF materials were subjected to various heat treatments, including solution annealing and stress relief, and were irradiated using in-situ and ex-situ ion techniques at temperatures of 300°C and 600°C, with doses ranging from 0.2 dpa to 25 dpa. Under ex-situ irradiation with 4 MeV Ni 2+ ions at 600°C, the dislocation cell structures in LPBF316L-1 and LPBF316H-1 gradually evolved into a uniform dislocation network. At a low irradiation dose (0.2 dpa), the cell structures were still partially visible. At 2 dpa, a uniform dislocation network formed, though remnants of the original cell structure were still discernible as contrast domains. At 5 dpa and 10 dpa, even the contrast domains vanished. For irradiation at 300°C, the cell structure was still clearly visible at 0.2 dpa for LPBF316L-1. For LPBF316H-1, the dislocation cell structure was less apparent at the same dose but was still recognizable. With further increase in dose at 300°C, the dislocation cell walls were completely replaced by irradiation-induced defects and no longer visible. Void formation was observed for irradiation at 600°C. At 2 dpa, no evident voids were observed in either LPBF316L-1 or LPBF316H-1.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Variation of γ′ Formers and Refractory Elements for Enhanced Creep resistance and Phase Stability of HAYNES® 282® Alloy

Modifications to the chemistry of alloy 282 were performed to improve the alloy’s resistance to long term creep deformation as well as phase stability. Alloys were prepared using vacuum induction melting, computationally optimized homogenization heat treatment and hot working. Phase stability studies were carried out for up to 5,000 hours at 800°C and 900°C while creep testing was performed at conditions leading to lives past 7,000 hours for temperatures ranging from 740°C to 900°C. The formation of σ and μ phases were reduced in the modified alloy. Atom probe tomography (APT) was performed on the specimens from the phase stability study to investigate changes in the elemental partitioning to the γ and γ′ phases. Post deformation microstructures were analyzed using EBSD and TEM to study the influence of the detrimental phases on damage accumulation during creep.

Detrois, Martin↗
DOE OSTI2024

Microstructural evaluation of the creep behavior in L-PBF Ni-based superalloys

This presentation at ICAM 2024 Conference focuses on the commonalities and differences in the creep rupture behavior and creep mechanisms for three distinct classes of laser powder-bed fusion (L-PBF) Ni-based superalloys (γ’-precipitate strengthened Haynes® 282®, γ’/γ”/δ-precipitate strengthened Alloy 718, and solid-solution strengthened Alloy 625) as compared to conventionally processed counterparts. A comparison of Larson-Miller parameter plots establishes that these alloys perform statistically within the bounds established for the wrought product, despite having dissimilar microstructural features and other artefacts associated with PBF-LB manufacturing and post-processing heat treatment. To understand the failure and the impact of composition, minor phases, and deformation defects on creep behavior, the fractography has been performed and microstructures have been evaluated in detail with SEM-EDS, EBSD, and HAADF-STEM. The underlying diffusional and dislocation creep mechanisms associated with this microstructural evaluation is discussed. This work is supported by NETL-FWP-1022408 Advanced Turbines.

Sudbrack, Chantal↗
DOE OSTI2025

Location-Specific Microstructures and Properties of Haynes 282 Alloy with Laser-Wire DED Processing

In this work, the location-specific microstructures in terms of grain morphology, texture, γ′ precipitates, carbides, and residual strains were investigated in a series of laser-wire direct energy deposition (LW-DED) Haynes 282 alloys with varied processing parameters. A bimodal grain distribution was found in these as-printed and heat-treated alloys with columnar grains within the layers and fine equiaxed grains at the interlayer regions. Dominant <001> texture along the build direction with more obvious <111> orientation preference exists at the bottom layers, compared to the top layers. The gradient γ′-precipitates size distribution contributes predominantly to the observed gradient hardness distribution in the as-printed samples. The heat-treated 282 exhibit comparable yield strengths to those conventionally-processed counterparts, while the observed small deviation in their yield strengths is attributed to the Hall-Petch effect. This work establishes the correlation between location-specific microstructures and mechanical properties, providing valuable insights into future printing parameters and heat-treatment optimization.

Haynes 282↗
DOE OSTI2025

Chemical Analysis of Tantalum Thin Films compared to Niobium Thin Films using SIMS and XPS

Superconducting qubits are a leading platform for quantum computation. These circuits are typically made from superconducting materials like aluminum or niobium. However, the amorphous niobium oxide and aluminum oxide on the surface of these circuits introduce considerable RF loss due to the presence of two-level systems (TLS), which limits the maximum coherence times T1 to ~100 μs. Capping the niobium qubits with a tantalum layer leads to a 3- 5x improvement [Bal et al., 2024]. But even in this case, tantalum forms an amorphous surface oxide that introduces loss. In an effort to devise strategies to eliminate the presence of this oxide, we present a comprehensive study on the nature of Ta oxide using x-ray photoemission spectroscopy (XPS) and secondary ion mass spectrometry (ToF-SIMS) as a function of heat treatment. The thin films were annealed in ultra-high vacuum conditions and analyzed in situ to characterize the composition and evolution of the native tantalum oxide layer and oxide-metal interface. Our analysis reveals two critical differences between tantalum and niobium oxides: Nb2O5 completely dissolves at 400°C, while Ta2O5 persists even at 800°C. Additionally, tantalum oxide contains only a single suboxide (TaO), in contrast to niobium's two suboxides (NbO and NbO2). The suboxide of tantalum contributes minimally to the total oxide content and shows a relative increase with temperature. Understanding the oxide’s behavior will open new pathways for optimizing coherence times in tantalum qubits.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

CABLE Stage 3 – Ultra‐High Strength/Highly Conductive Al Alloys

This work is to be conducted in support of the CABLE Conductor Manufacturing Prize Program awarded by NREL. The intent is to connect competitor teams with national laboratories that can help accelerate the development of innovative solutions and products. Teams who receive CABLE Prize awards are eligible to utilize vouchers at national laboratories to advance their ideas. NanoAL LLC has been awarded a voucher to utilize at Ames National Laboratory. Ames National Laboratory will perform a scale‐up trial of Nano 6000‐T9 to evaluate and optimize the heat treatment and other processing variables to validate the lab‐scale work done at NanoAL. The final processing schedule will be used to fabricate the submission samples for the Stage 3 contest. All work will be supported by mechanical and electrical conductivity testing be performed by Ames.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Rapid Design and Manufacturing of High-Performance Materials for Turbine Blades

This research demonstrated the concept of carbide precipitation-strengthened refractory high entropy alloys (RHEA). The advantage of a precipitation strengthened alloy is all phases are in thermodynamic equilibrium promoting microstructural stability, and consequently retention of properties at elevated temperatures. Additionally, as with any precipitation strengthened – or age hardened - alloy, components can be heat-treated after manufacturing to manipulate the microstructure and optimize properties for performance. This is an advantage of the precipitation strengthened alloys over composites and ceramics materials, where the microstructure and properties are essentially fixed upon the initial materials manufacturing stage. High throughput (HT), multi-scale computer modeling was used to identifying novel RHEA compositions with desired characteristics needed for precipitation strengthening. Designs were validated by producing small ingots via are melting. The results showed that carbides precipitated and consequently, the strength of the alloys (measured in compression) increased after heat-treatment, which is the desired effect. The project also demonstrated the feasibility of producing articles from RHEA by additive manufacturing (AM). Electron beam melting (EBM) and laser direct energy deposition (L-DED) additive manufacturing methods, were explored with various processing parameters were interrogated for both methods. Sound (crack-free and dense) precipitation strengthened RHEA samples were produced via EDM AM, demonstrating the feasibility of the concept.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Robust Dissimilar Metal Friction Welded Spool for Enhanced Capability for Steam Power Components (Final Program Report)

This project successfully demonstrated the feasibility and advantages of producing durable, friction-welded dissimilar-metal spools, both with and without transition pieces, as well as the use of advanced oxidation-protective coatings for steam power applications. The work encompassed the optimization and full-scale production of NFA tubing, overcoming manufacturing and processing challenges to achieve enhanced strength, creep, and fatigue properties validated by extensive microstructural characterization. Optimized welding techniques were developed and refined for joining dissimilar materials, resulting in defect-free welds optimized for both low- and high-pressure boiler circuits. Systematic evaluation of welding parameters, coupled with heat treatments, ensured reliable performance and minimized weld defects such as banding and cracking. Comprehensive mechanical and non-destructive testing, including tensile, bend, fatigue, and CT scanning, confirmed the superior integrity and durability of the friction-welded joints under representative service conditions. To address oxidation-related degradation, a range of protective alloy coatings—such as IN625, APMT, Duplex 2507, and FeCrAlY—were selected and evaluated for their ability to counteract oxide notch formation at dissimilar metal interfaces. These coatings demonstrated improved oxidation resistance and long-term stability under thermal cycling, thereby extending weld service life. Thermal cyclic testing and long-term studies captured the phase stability and diffusion behavior of coated and uncoated configurations. Validated models for low-cycle fatigue (LCF), creep, and thermal mechanical fatigue (TMF) were developed to predict component life and failure modes. These models confirmed that friction-welded configurations exhibited significantly enhanced performance compared to conventional gas-tungsten arc welding (GTAW), with up to 7× improvement in creep resistance and at least 2× enhancement in fatigue properties. The introduction of a tailored transition piece further reduced thermally induced strains, enhancing fatigue life. The results demonstrate a robust pathway for retrofitting existing steam fleet components and upgrading future equipment to deliver substantially improved cold-start cycling behavior and reduction of unplanned outages due to premature weld failures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Reducing Mass of Steel Auto Bodies using Thin Advanced High Strength Steel with Carbon-Fiber Reinforced Epoxy

Diversitak, a company based in Detroit, MI, has developed a proprietary, low specific gravity, carbon fiber-reinforced epoxy (CFRE) under U.S. patent number 9,963,58832. Preliminary testing on this new material conducted in collaboration with ArcelorMittal Steel Company proved out the CFRE concept. A thin layer of this CFRE was applied to a stamped sheet of steel with residual stamping oils from a mill, in a time corresponding to automotive processing (e.g., ~15 seconds), and processed following automotive e-coat procedures (phosphating + 175–200°C heating), to complete the curing. No problems with adherence or performance were noted. While the CFRE does add weight to a thin gauge steel panel, it weighs much less than what is displaced by using thicker conventional mild steel gauges. The application of the coating showed a significant increased dent resistance, oil canning resistance, and part stiffness.This current two-year project was designed to mature this new technology to near manufacturing readiness to reduce the weight of a vehicle and lower the cost of weight reduction. The process involves the use of thinner gauge steels than are currently used. The collaborative development team included two industrial manufacturers: Diversitak and ArcelorMittal Steel Company; LightMAT; and two National Laboratories: Oak Ridge National Laboratory (ORNL) and Idaho National Laboratory (INL). The team developed a new manufacturing process to reduce the weight of a vehicle and lower the cost of weight reduction, as well as a better understanding of how to apply the coating so that it will perform to a high standard in-service. The team also performed an in-depth study to determine the long-term durability of the materials manufactured using this technology and well-known automotive industry standard tests.The overall process involved stiffening the thinner gauge steel by applying the CFRE on only one side. To accomplish this goal, the optimal reinforcement fiber length and fiber concentration was first determined. This was followed by measuring the coefficient of thermal expansion (CTE) in all three directions, so it could be fed into manufacturing models and methods for rapidly and inexpensively applying the coating. This was followed by panel level evaluations of the coating and steel combination, and then by full part demonstration of the technology on door panels. The final step was corrosion testing of the parts.ArcelorMittal characterized the advanced high strength steel (AHSS) (e.g., metallurgy-heat treatment for required AHSS properties as a function of the sheet thickness, state of internal stress) and quantified CFRE adhesion to the steel as a function of sheet preparation (e.g., rolling and stamping).ORNL optimized the fiber length, fiber concentration, and coating thickness for best vehicle function and performance at the least cost. Along with the suppliers, ORNL developed a durable CFRE application process (e.g., gun material, design, robotic dispensing process) and identified the adhesion stability of the CFRE during process holding. An approach to ensure that application/curing timing conforms to conventional assembly line speed and plant cycle times was determined. ORNL also determined the CTE of the material in all three directions and performed material scanning electron microscopy (SEM) analyses.INL characterized the corrosion properties of the steel panels coated with CFRE. The panels were investigated for corrosion resistance and stability as replacement materials used in automotive body panels to reduce mass. The coupons tested at INL were supplied by Diversitak after an optimized CFRE formulation was achieved in the already coated form for corrosion testing.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2024

Embedded Aluminum Nitride Sensors for Advanced Reactors

This project aims to manipulate the of growth of aluminum nitride (AlN) inclusions in an iron-chromium-aluminum (FeCrAl) alloy, using the principle of powder metallurgy and heat treatment methods. to promote the formation of AlN phase within FeCrAl for embedded sensing. This effort seeks to fill in a gap with respect to robust sensor hardware for ubiquitous structural health monitoring of advanced nuclear reactors. A systematic evaluation of various solid-state methods will be performed to understand the influence of process conditions on AlN growth and to promote the growth of desirable AlN phase. Fabricated specimens will be analyzed to investigate the AlN structures that are formed using a suite of tools to characterize the concentration, morphology, and distribution of AlN within the FeCrAl substrate.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Canister Centerline Cooling Experiments for DPF5-336 Reference Material Made with ERV3b Salt Simulant

This report provides experimental details and results on the elemental distributions (compositions), crystalline/amorphous phase distribution, and microstructures for DPF5-336 reference materials made with ERV3b salt that were subjected to the canister centerline cooling (CCC) heat treatment process. To fabricate these materials, ammonium dihydrogen phosphate was mixed with ERV3b salt simulant and a dechlorination procedure was run in the generation-2 dechlorinator at the Pacific Northwest National Laboratory up to 600°C in an alumina crucible. After the dechlorination process, the product was removed from the crucible, lightly crushed, loaded into a new alumina crucible, Fe 2 O 3 was added, and this was vitrified at 1100°C for 1 hour and quenched. The quenched material was mostly amorphous but showed some small diffraction peaks attributed to Li 3 Fe 2 (PO 4 ) 3 . This quenched material was ground to a fine particle size in a milling chamber, and this was subjected to the CCC cooling profile in duplicate within alumina and fused quartz crucibles. The CCC experiment is designed to simulate the slowest cooling profile (the vertical centerline) of a 0.61-m diameter canister where the slower cooling profile often results in the production of a variety of different crystalline phases upon formation of which result in a residual glass of unknown composition and properties. The information gleaned from these types of experiments will lead to improved composition-property predictions for materials with similar compositions. The results of the alumina and fused quartz experiments show different microstructures but similar diffraction patterns providing evidence of similar crystalline phases being present in each sample. Both samples had monazite [i.e., (Ce,Nd)PO 4 ] and mixtures of phases containing P, Fe, and alkali metal elements. This report completes the milestone M4FT-23PN030104042 with details provided in Appendix B.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Bismuth-Functionalized Silica Aerogels for Iodine Capture

The U.S. Department of Energy is looking into alternative sorbents for the removal of radioiodine from off-gas streams in a used nuclear fuel reprocessing plant. One class of sorbents considered are bismuth-functionalized silica aerogels which offer an efficient capture of iodine from off-gas streams and are environmentally friendly and lower cost when compared to silver-functionalized sorbents. Two types of bismuth-functionalized silica aerogels were successfully manufactured using a hierarchical synthesis approach:1) The Bi 3+ -aerogel with bismuth oxide nitrate hydroxide hydrate particles and 2) Bi-aerogel with bismuth metal and bismuth sulfide nanoparticles. Both sorbents exhibited high sorption capacity for iodine. However, presence of particles of different composition, size, and distribution on aerogel support resulted in different iodine loadings. The Bi 3+ -aerogel exhibited sorption capacity of 289 mg/g. In contrast, Bi-aerogel exhibited more that 20% higher sorption capacity. The heat-treatment of Bi 3+ -aerogel at 225? under hydrogen atmosphere increased iodine loading capacity to 351 mg/g.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Direct Feed High-Level Waste APPS Model Glass Testing (DFHLW APPS) Matrix, Phase 2

This report summarizes the data collected during the batching and melting of a second matrix of Direct Feed High-Level Waste (DFHLW) glasses generated using the preliminary enhanced waste glass models (EWG2.5) and the Britton and Anderson (2024) preliminary DFHLW feed vector. The purpose of these glasses is two-fold: 1. Validate EWG2.5 glass calculations being used in the Aspen Process Performance Simulation (APPS) model. 2. Evaluate and ultimately improve the glass property models and formulation methods used for design of DFHLW glasses as part of an iterative process of data collection and model refinement. Some of the 16 APPS2 glasses tested did not satisfy all target property constraints due to the limited data on DFHLW glass supporting the EWG2.5 models. • One glass, APPS2-10, formed nepheline on canister centerline cooling (CCC) heat-treatment and failed the product consistency test (PCT) response limits. This glass also had high B and Cr release rates for the toxicity characteristic leaching procedure (TCLP). All other glasses were found to satisfy the PCT and TCLP constraints for both quenched and CCC samples. • One glass, APPS2-08, had higher than acceptable viscosity due to magnetite crystallization. • One glass, APPS2-09, formed greater than 2 vol% crystals at 950 °C. As the glass design criterion was that the temperature at 2 vol% crystal (T 2% ) be less than 950 °C, only one glass failed the criteria. However, this criterion is being reevaluated. Four additional glasses formed crystal fractions between 1 and 2 vol% at 950 °C (APPS2-03, -08, -12, and -14). • Four glasses – APPS2-01, -02, -04, and -16 – failed the Monofrax K-3 refractory neck corrosion (k neck ) design limit of 0.04 in. at 1208 °C for 6 d. This is another criterion being reevaluated. Four additional glasses (APPS2-05, -06, -11, and -13) exhibited 0.025 = k neck = 0.04 in. • All 16 glasses passed the sulfur solubility and TCLP constraints. The measured property values were compared to predicted values using EWG2.5 and a selection of other existing models. A few models (e.g., electrical conductivity, TCLP) were found to be adequate for designing DFHLW glasses in the near future, while others require refits or offsets. It is recommended that new property models be developed for EWG3.0, as a large amount of DFHLW glass property data (> 14 × existing data) is expected to be collected in the compositional spaces where no data was previously available. To enable near-term calculations and formulations for designing DFHLW glasses and processing rate estimations, a formulation algorithm with minor modifications will be developed, EWG2.6.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

Nepheline constraint for hanford HLW glass

The present work was intended to expand the available HLW glass property-composition data relating to nepheline formation on CCC heat treatment and to develop improved models to predict nepheline formation that would allow processing of high waste loading high-Al HLW glass formulations at the WTP.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

Computational Design to Advance AM Fabrication of High Gamma Prime Alloys for Hot Gas Path Components in Gas Turbine Engines: A Pathway to Enhanced Gas Turbine Efficiency and Energy Saving (Final CRADA Report)

Raising turbine inlet temperature is a key lever for improving industrial gas-turbine efficiency and power output, but it increases thermo-mechanical demands on hot-gas-path components. Additive manufacturing (AM), particularly laser powder bed fusion (L-PBF), enables complex internal cooling features in critical components such as turbine tip shoes that are difficult to produce by conventional casting. However, qualification of new high-temperature AM alloys and aggressive geometries is often limited by trial-and-error iteration of build parameters and post-build heat treatments, with cracking during stress relieving or hot isostatic pressing (HIP) being a recurring failure mode.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2026

Gaseous Hydrogen Embrittlement of L-PBF Ni-Based Superalloys for Service in Natural Gas Turbines

Efforts to improve efficiency of industrial gas turbine engines have focused on increasing operating temperatures by use of fuel-flexible gas blends. Ni-based superalloys are susceptible to hydrogen embrittlement (HE), leading to potential risk of premature component failure. Certain turbine components exposed to hydrogen-rich environments are manufactured from additive processes like laser powder bed fusion (L-PBF). The HE susceptibility was evaluated for three Ni-based superalloys: solid solution strengthened Alloy 625, γ’/γ’’-precipitation strengthened Alloy 718, and γ’-precipitation strengthened Haynes® 282®. L-PBF samples were pre-charged under medium and high pressure gaseous hydrogen before tensile testing at temperatures up to 260 °C using a fast strain rate. Selected samples were subjected to a service conditioning heat treatment prior to hydrogen charging to evaluate the change in susceptibility after prolonged service. The susceptibility to HE and HE mechanisms of these three alloys is compared.

additive manufacturing↗