Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GaS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

All-aerosol-jet-printed highly sensitive and selective polyaniline-based ammonia sensors: a route toward low-cost, low-power gas detection

In this work, we report the design and scalable fabrication of a low-cost and low-power polyaniline-based (PANI) ammonia (NH3) gas sensor on polyimide (PI) substrates using additive manufacturing techniques. The silver interdigitated electrode (IDE) arrays and conducting polymer films are printed onto PI using a direct-write technology of aerosol-jet printing. Morphological characteristics are examined by scanning electron microscopy and energy-dispersive X-ray analysis which reveal homogeneously printed PANI film on the IDE platform. The gas sensing performance is evaluated in the analytical early leak detection range of 5–1000 ppm NH3 in air as a function of both thermal (23 °C, 50 °C, 80 °C) and relative humidity (RH = 0%, 30%, 50%) exposures. The sensor exhibits sensitivity down to 5 ppm NH3 with a sub-ppm detection limit and good repeatability. We observe rapid NH3 detection at 0% RH with very extended times for equilibration and recovery. However, at both 30 and 50% RH, the room temperature response and recovery times are reduced to only about 1 min and 5 min, respectively. Experiments also reveal good sensitivity toward the analyte even at higher operating temperatures. Present results merit the practical application of aerosol-jet-printed, low-power sensors for industrial applications where low-level hazardous gas detection is essential.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Carrier gas attenuation in gamma assay of radioactive xenon samples

Gamma attenuation attributable to xenon and carbon dioxide carrier gas in radioactive xenon assay samples has been calculated using Monte Carlo n-Particle (MCNP) transport code for the 0.65 mL flame sealed ampoule (bean), and 15 mL and 50 mL Schlenk tube geometries. The attenuation was correlated as a % loss per standard mL of carrier gas. In this work, high Purity Ge gamma spectroscopy experiments were performed to measure against the MCNP results. The experimental results from the 133 Xe in xenon carrier gas in a bean geometry showed 0.97 ± 0.4% loss per standard mL xenon, which was in agreement with the MCNP predictions.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
DOE OSTI2025

Explosive Byproduct Gas Transport Through Sorptive Geomedia

Current underground nuclear explosion (UNE) detection strategies rely heavily on atmospheric noble gas sampling of radioxenon. However, discriminating nuclear weapons testing programs from civilian sources is difficult due to highly variable atmospheric radioxenon backgrounds and processes affecting subsurface transport of parent radionuclides. Here, we aim to study the transport of gases produced by subsurface explosions as novel stable signatures for underground nuclear explosion (UNE) monitoring. These gases may be produced in large quantities with distinct molecular ratios, which will be impacted by subsurface transport processes. To demonstrate how ratios of gases produced by explosions can change during transport in geomaterials, we conducted laboratory benchtop experiments on the transport of carbon dioxide (CO 2 ) and hydrogen (H 2 ) gases through variably saturated zeolitic tuff, which is abundant at the historic US testing site. We observed that zeolitic tuff sorbs substantial quantities of CO 2 while allowing H 2 to transport more freely, leading to changes in the molecular ratios of the two gases along the transport pathway. Gas uptake in the dry zeolitic tuff core was 72.3% for CO 2 , compared with 53.4% for xenon and 7.6% for H 2 . The presence of 20% water saturation disrupted the CO 2 sorption process, though to a lesser extent than observed for noble gases, with a 36.7% drop in xenon sorption compared with a 21.9% drop for CO 2 . These results represent the first observations of zeolite sorption altering explosive gas ratios during transport through geomedia relevant to nuclear proliferation monitoring.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Temperature-induced changes in the synthesis gas composition in a high-temperature H 2 O and CO 2 co-electrolysis system

Solid oxide electrolysis cell (SOEC) is an attractive renewable technology capable of producing synthesis gas (H 2 + CO) from H 2 O and CO 2 . An SOEC consists of a solid oxide electrolyte and two ceramic or metal-ceramic electrodes. H 2 O and CO 2 are electrolyzed at the cathode producing H 2 and CO, releasing O 2- ions, which travel through the electrolyte to the anode side and recombine to produce pure oxygen gas as the byproduct. In the present study, a La 0.7 Sr 0.2 Ni 0.2 Fe 0.8 O 3 cathode was used to co-electrolyze H 2 O and CO 2 at three different operating temperatures- 700 °C, 750 °C and 800 °C. Synthesis gas was produced at all three operating temperatures with 100% Faradaic efficiency. The composition of the syngas, however, was found to be a function of the operating temperature. In general, the H 2 /CO ratio in the syngas decreased with increased temperature. This was partially due to CO 2 electrolysis becoming more favorable compared to H 2 O electrolysis at higher temperatures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Disentangling interlayer confinement and pore surface adsorption in functionalized smectites for tunable ethylene gas capture

Smectite-based adsorbents are increasingly being studied as sustainable packaging materials for scavenging ethylene, a plant hormone that accelerates fruit ripening. However, the mechanisms governing their uptake and retention remain poorly understood. Here, to tackle this question we systematically investigate ethylene gas-solid interactions in pristine, acid-activated, and choline-functionalized montmorillonites using a complementary combination of structural, gravimetric, and spectroscopic techniques, including inelastic neutron scattering. We experimentally distinguish ethylene populations associated with interlayer confinement, mesopore, and external surface adsorption. We show that chemical functionalization distinctly controls adsorption pathways: acid activation enhances total uptake by generating mesoporous adsorption sites and promoting partial interlayer intercalation, yielding capacities comparable to those of leading smectite-based adsorbents, while choline functionalization promotes preferential confinement and stabilization of guest molecules within the interlayer galleries. Advanced spectroscopic analysis provides molecular-level insight into confinement environments and interaction strengths. We also establish clear structure-property relationships by correlating uptake values derived from independent techniques, linking chemical modification, accessible adsorption domains, and retention behavior. These findings provide general design principles for tuning gas-solid interactions in functionalized layered silicates and highlight their potential as adaptable platforms for sustainable ethylene gas capture and selective adsorption technologies.

Ethylene adsorption mechanism↗
DOE OSTI2022

Modeling gas release from a Bingham plastic slurry and deconvoluting measured data

Physics-based models for predicting the off-gassing characteristics of agitated slurries are presented. This approach decomposes the system into two separate but coupled slurry and headspace models. The physics driving bubble transport through the slurry and gas mixing within the headspace are discussed. An analytical expression for predicting the time evolution of the headspace concentration using first principles theory is also presented. Predictions from the numerical models, as well as expectations from the analytical solution, both agree with measured off gassing data for two different experimental operating conditions. After benchmarking the numerical model predictions against experimental data, the model was used to make predictions for gas release from a full-scale vessel and to perform sensitivity analyses to examine the sensitivity of gas release to parameters such as yield stress, consistency index, slurry density, bubble size, bubble concentration, and impeller speed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Quantifying the anion effect of gas solubility within ionic liquids using the solvation affinity index

The solubility of gas molecules within ionic liquids (ILs) is strongly dictated by the anion effect and the free volume effect, and of these two influences, the anion effect can be challenging to predict. We evaluate a wide range of different gas solutes (O 2 , NH 3 , CH 4 , H 2 S, SO 2 , Ar, H 2 , N 2 , CO 2 ) in different ILs, and we find that the solubility is strongly correlated to one of three different IL properties, which can be directly calculated from the anion electrostatic potential (ESP) surfaces. Thus, the solutes can be grouped into three fundamental types, leading to a general descriptor, the solvation affinity index (SAI), which can identify the affinity between a wide range of gas solutes and IL solvents. The SAI of nine common industrial gases with 47 common anions are generated. Furthermore, this can provide a fast approach for pre-screening IL solvents or even for ILs embedded within porous supports.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Integration of hydrophobic gas diffusion layers for zero-gap electrolyzers to enable highly energy-efficient CO 2 electrolysis to C 2 products

Electrochemical CO 2 reduction (eCO2R) is an attractive route for mitigating global CO 2 emissions while producing value-added chemicals. Ethylene is one product of eCO2R and is an essential industrial precursor with a global market of $230 billion. The large-scale implementation of C 2 H 4 -selective CO 2 electrolyzers remains challenging because of low energy efficiencies. In this work, we develop the design principles necessary for incorporating an expanded polytetrafluoroethylene (ePTFE) electrode into a zero-gap electrolyzer while simultaneously developing an integrated electrical front contact that reduces the ohmic resistances inherent to electrically insulating gas diffusion layers. By co-designing the catalyst layer, gas diffusion medium, and operating conditions for a zero-gap ePTFE gas diffusion electrode (GDE), we achieved a full-cell voltage of 2.5 V at 200 mA cm −2 at 25 cm 2 geometric area cell with Faradaic efficiencies of 48% for ethylene and 40% for ethanol. This work highlights strategies for developing a scalable, stable, and highly energy-efficient eCO2R for C 2 products.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Production of mechanically-generated 316L stainless steel feedstock and its performance in directed energy deposition processing as compared to gas-atomized powder

The objective of this work is to study the feasibility of mechanically-generated feedstock for use in directed energy deposition (DED) processing. Mechanically-generated powder was created by machining 316L stainless steel bar stock followed by comminution of the resulting chips through oscillation ball milling. This methodology's production yield and processing time for the specifications of a commercially available DED system are presented along with resulting powder morphology. Performance of the mechanically-generated feedstock was compared to gas-atomized powder and evaluated based on the following figures of merit: flowability, printed part height, printed part density, and chemical compositional stability throughout processing. Mechanically-generated feedstock was created to meet deposition system requirements. Compared with gas-atomized powder, mechanically-generated powder did not flow as well through the powder-delivery system. Parts printed from mechanically-generated feedstock were generally taller than their counterparts from gas-atomized feedstock, but their densities were less predictable. As a result, chemical composition of prints using both feedstocks was within standard nominal compositions for 316L stainless steel.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Influence of gas expansion on the propagation of a premixed flame in a spatially periodic shear flow

It has been previously demonstrated that thermal gas expansion might have a role in boundary layer flashback of premixed turbulent flames, inducing local flow-reversal in the boundary layer's low-velocity streaks on the reactants’ side of the flame and facilitating its upstream propagation. Here, we perform a two-dimensional numerical investigation of the interaction between a periodic shear flow and a laminar premixed flame. The periodic shear is a simplified model for the oncoming prolonged streamwise velocity streaks with alternating regions of high and low velocities found in turbulent boundary layers in the vicinity of the walls. The parametric study focuses on the amplitude and wavelength of the periodic shear flow and on the gas expansion ratio (unburnt-to-burnt density ratio). With the increase of the amplitudes of the periodic shear flow and of the gas expansion, the curved flame velocity increases monotonically. The flame velocity dependence on the periodic shear wavelength is non-monotonic, which is consistent with previous theoretical studies of curved premixed flame velocity. The flame shape that is initially formed by the oncoming periodic shear appears to be metastable. At a later stage of the flame propagation, the flame shape transforms into the stationary one dominated by the Darrieus-Landau instability.

42 ENGINEERING↗
DOE OSTI2020

Pollution to products: recycling of ‘above ground’ carbon by gas fermentation

Climate crisis and rapid population growth are posing some of the most pressing challenges to mankind and have intensified the need for the deployment of carbon recycling and carbon capture and utilization (CCU) technologies. Gas fermentation offers a solution using carbon-fixing chemolithoautotrophic microorganisms. After a decade of scale up, the technology has recently been commercialized with the first plant operating successfully since 2018 and additional units under construction. Gas fermentation offers unique feedstock and product flexibility when compared to other available gas-to-liquid technologies. Advancements in process technology and synthetic biology enable a broad range of feedstocks including emissions from industry or syngas generated from any biomass resource to be converted into a wide range of molecules realizing a circular economy.

09 BIOMASS FUELS↗
DOE OSTI2022

Supercritical, liquid, and gas CO 2 reactive transport and carbonate formation in portland cement mortar

In this paper, we investigate carbonate formation and reactive transport rate in variably saturated portland cement mortars when high concentrations of gas, liquid, or supercritical CO 2 flow through their pore network. Xray computed tomography completed during CO 2 flow is used to quantify the microstructural evolution as the mortar carbonates. After in situ tests, higher resolution scans, thermogravimetric analysis, and desorption isotherm analysis are performed to further quantify microstructural changes. We found that at dry conditions supercritical CO 2 moves more rapidly through the pore space and precipitates more carbonates than liquid or gas CO 2 . However, at 50% degree of saturation (DOS) the CO 2 state did not affect the rate of transport in that each specimen exposed to a different CO 2 state carbonated within the first hour of CO 2 exposure. When the pore space is at 50 or 100% DOS, supercritical CO 2 did not react with hydration products more rapidly nor did it result in more carbonate formation during exposure compared to gas or liquid CO 2 . The amount of Ca(OH) 2 that contributes to CaCO 3 formation is correlated to the DOS. For the mortar composition analyzed, Ca(OH) 2 contributes to approximately 40% of the carbonates formed in the 50% DOS specimens and 15% in the 100% DOS specimens. In other words, as the amount of moisture in the pore space increases, phases other than Ca(OH) 2 contribute to more than 50% of the total CaCO 3 formed.

42 ENGINEERING↗
DOE OSTI2026

Analysis of synergies in converting underground storage sites: Natural gas to hydrogen with co-located CO2 storage

This study examines the untapped potential of synergistically converting underground natural gas storage (UGS) into underground hydrogen storage (UHS) with co-located CO2 storage. Current approaches to subsurface storage technology (SST) development often prioritise single-use scenarios, overlooking the benefits of integrating multiple technologies. We investigate converting UGS assets into UHS through gradual cushion-gas injection over multiple years, rather than injecting all cushion gas in the first year, and include on-site CO2 storage to offset site emissions. Mechanistic modelling shows this gradual transition reduces the Levelised Cost of Storage (LCOS) of H2 by 1.2-13.1% while retaining energy output within 3% of the current status quo. We also show that combined UHS and CO2 storage hubs can reduce the LCOS of CO2 by 45-77% for only a 3-10% increase in hydrogen LCOS relative to the status quo. This analysis framework may help future-proof SST sites and support a resilient, economically beneficial energy transition.

Mouli-Castillo, Julien↗
DOE OSTI2022

Dehydration of gas-phase benzyl amine alcohols studied at atmospheric pressure

Gas-phase ion chemistry is a useful approach for the investigation of physical organic chemistry and the study of reactivity, structure, and thermochemical properties of ionic and neutral organic substrates. Herein, one-step dehydration of gas-phase benzyl amine alcohols to give benzazetidines was discovered without the use of catalysts. Mechanistic investigations of the gas-phase dehydration reactions were explored to study the possible influence of charged microdroplet acceleration during electrospray ionization (ESI) and collisions occurring during ion transfer through the atmospheric pressure interface (API) of the mass spectrometer. The product ion distribution was observed to be less sensitive to droplet effects (spray distance and voltage), and temperature of transfer capillary in the API. However, the product ion distribution exhibit high sensitivity to different S-lens radio frequency (RF) voltage of the API, providing evidence that the dehydration reaction is driven by collisions during ion transfer in the API. With this insight, we developed atmospheric pressure thermal dissociation platform that allowed thermal-induced collisions outside of the mass spectrometer when the benzyl amine alcohols are carried through a heated coiled tube. Up to 98% dissociation efficiency was achieved with the coiled tube heated to a temperature of 200 °C, yielding only the desired benzazetidine product. Finally, by performing the atmospheric pressure thermal dissociation experiment outside of the mass spectrometer, we believe it will be straightforward to collect the dehydration product.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

How does urbanization affect CO 2 emissions of central heating systems in China? An assessment of natural gas transition policy based on nighttime light data

Understanding the different impacts of urbanization on sectorial carbon dioxide (CO 2 ) emissions at different spatial scales is of great importance for the evaluation of energy transition policies and reduction of environmental inequality. However, how urbanization affects the CO 2 emissions of central heating systems at high spatial resolution in China has not been fully studied before. Based on satellite-observed NPP-VIIRS nighttime light (NTL) data, we develop a 5 km x 5 km annual CO 2 emission inventory for coal boilers, thermal power plants (TPPs), and natural gas boilers in China's central heating systems for the period 2012-2017 by using the geographical and temporally weighted regression (GTWR) model. It is observed that nonurban areas generated 2-4 times the CO 2 emissions of coal boilers in urban areas. The largest increments of CO 2 emissions of gas boilers are observed in urban areas of the eastern (6.80 times) and central regions (2.86 times) in 2013-2014, due to the clean heating policy in the "2 + 26" cities in China. The effects of urbanization on CO 2 emissions from natural gas boilers are approximately 2-3 times those of coal boilers, and the differences are largest in western cities with only minor differences in northeastern cities. Overall, our results will aid in designing low-carbon development goals and provide micro-level information on central heating facilities in urbanized and less developed regions.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Life cycle greenhouse gas emissions of different CO 2 supply options for an algal biorefinery

This paper characterizes the greenhouse gas (GHG) emissions from the provision of CO 2 for twelve hours of the day from a range of sources operating on a twenty-four-hour basis. Twelve CO 2 supply cases spanning from fossil fuel power plant stack gases to direct air capture (DAC) systems are modeled. The results are compared in a life cycle assessment (LCA) framework. The CO 2 supply from the combustion or gasification of biomass has GHG emissions of –1.62 gCO 2 eq./g CO 2 delivered and is the case with the lowest carbon footprint for supplied CO2. The emissions for all the CO 2 supply cases were found to be negative, either because of capturing more CO 2 from the atmosphere than is released from the CO 2 production process, or because of production of excess electricity that is exported to the grid (replacing emissions from grid electricity). A purpose-built Natural Gas Combined Cycle (NGCC) power plant CO 2 source has the highest GHG emissions of -0.40 gCO 2 eq./gCO 2 delivered of the cases considered because of nighttime emissions and natural gas supply chain losses. The impact of a diurnal cycle can be mitigated by using capture and refrigeration systems as part of the CO 2 management system. The results are sensitive to the GHG emissions of the grid electricity, which is imported or exported in different cases. The results provide a benchmark for the comparison of different CO 2 supply options for the establishment of a sustainable algal biorefinery.

42 ENGINEERING↗
DOE OSTI2022

Gas diffusion through variably-water-saturated zeolitic tuff: Implications for transport following a subsurface nuclear event

Noble gas transport through geologic media has important applications in the characterization of underground nuclear explosions (UNEs). Without accurate transport models, it is nearly impossible to distinguish between xenon signatures originating from civilian nuclear facilities and UNEs. Understanding xenon transport time through the earth is a key parameter for interpreting measured xenon isotopic ratios. One of the most challenging aspects of modeling gas transport time is accounting for the effect of variable water saturation of geological media. In this study, we utilize bench-scale laboratory experiments to characterize the diffusion of krypton, xenon, and sulfur hexafluoride (SF6) through intact zeolitic tuff under different saturations. Here, we demonstrate that the water in rock cores with low partial saturation dramatically affects xenon transport time compared to that of krypton and SF6 by blocking sites in zeolitic tuff that preferentially adsorb xenon. This leads to breakthrough trends that are strongly influenced by the degree of the rock saturation. Xenon is especially susceptible to this phenomenon, a finding that is crucial to incorporate in subsurface gas transport models used for nuclear event identification. We also find that the breakthrough of SF6 diverges significantly from that of noble gases within our system. When developing field scale models, it is important to understand how the behavior of xenon deviates from chemical tracers used in the field, such as SF6 (Carrigan et al., 1996). These new insights demonstrate the critical need to consider the interplay between rock saturation and fission product sorption during transport modeling, and the importance of evaluating specific interactions between geomedia and gases of interest, which may differ from geomedia interactions with chemical tracers.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
DOE OSTI2023

Short-lived noble gas effluent trends from a research reactor

An understanding of anthropogenic sources of radioactive noble gases in the atmosphere is needed to enhance the discrimination ability of the International Monitoring System's sensors. These sources include commercial and research nuclear reactors and medical isotope production facilities. While abiding by local environmental ordinances these facilities all emit noble gas radioisotopes through normal operation. Here, this research presents measurements and analysis of noble gas isotopes ( 41 Ar, 135 Xe, 135m Xe, 137 Xe, 138 Xe, 87 Kr, 88 Kr, and 89 Kr) made directly at the stack of the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory. The Xe and Kr noble gases are concurrently observed with 41 Ar, a neutron activation product, when the reactor is operational. The magnitude of the Xe and Kr noble gases released is not constant over the HFIR cycle, but they temporally match the 41 Ar trend. An isotope activity ratio analysis of these shorter lived isotopes combined with the observation of the cycle's temporal trend helps understand the noble gas production mechanism at the HFIR. Isotopes with short half-lives are not useful for long-range environmental monitoring. However, these measurements could potentially be combined with atmospheric modeling to predict the background source term of the longer-lived Xe ratios at a monitoring station.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗