Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Enthalpy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

Finite difference solution to the three-dimensional, incompressible thermal energy boundary-layer equation

An implicit numerical method has been adopted for the solution to the three-dimensional, energy boundary-layer equation. The energy equation is written in terms of a dimensionless temperature function, the relative stagnation-enthalpy difference, and transformed by the introduction of a Blasius-type transformation of coordinates as well as dimensionless stream functions. The method is applied to the problem consisting of an infinite cylinder joined with its axis perpendicular to a thin, flat, heated plate. A Prandtl number equal to one is simply considered.

Fillo, J. A.↗
NASA NTRS1972

Demonstration of the range over which the Langley Research Center digital computer charring ablation program (CHAP) can be used with confidence: Comparisons of CHAP predictions and test data for three ablation materials

Comparisons of ablation calculations with the charring ablation computer code and ablation test data are presented over a wide range of environmental conditions in air for three materials: low-density nylon phenolic, Avcoat 5026-39HC/G, and a filled silicon elastomer. Heat fluxes considered range from over 500 Btu/sq ft-sec to less than 50 Btu/sq ft-sec. Pressures range from 0.5 atm to .004 atm. Enthalpies range from about 2000 Btu/lb to 18000 Btu/lb. Predictions of recession, pyrolysis penetration, and thermocouple responses are considered. Recession predictions for nylon phenolic are good as steady state is approached, but strongly transient cases are underpredicted. Pyrolysis penetrations and thermocouple responses are very well predicted. Recession amounts for Avcoat and silicone elastomer are less well predicted, although high heat flux cases near steady state are fairly satisfactory. Pyrolysis penetrations and thermocouple responses are very well predicted.

Moyer, C. B.↗
NASA NTRS1971

Transpiration and film cooling boundary layer computer program. Volume 2: Computer program and user's manual

A finite difference turbulent boundary layer computer program which allows for mass transfer wall cooling and equilibrium chemistry effects is presented. The program is capable of calculating laminar or turbulent boundary layer solutions for an arbitrary ideal gas or an equilibrium hydrogen oxygen system. Either two dimensional or axisymmetric geometric configurations may be considered. The equations are solved, in nondimension-alized physical coordinates, using the implicit Crank-Nicolson technique. The finite difference forms of the conservation of mass, momentum, total enthalpy and elements equations are linearized and uncoupled, thereby generating easily solvable tridiagonal sets of algebraic equations. A detailed description of the computer program, as well as a program user's manual is provided. Detailed descriptions of all boundary layer subroutines are included, as well as a section defining all program symbols of principal importance. Instructions are then given for preparing card input to the program and for interpreting the printed output. Finally, two sample cases are included to illustrate the use of the program.

Gloss, R. J.↗
NASA NTRS1972

Thermophysical properties of parahydrogen from the freezing liquid line to 5000 R for pressures to 10000 psia

The tables include entropy, enthalpy, internal energy, density, volume, speed of sound, specific heat, thermal conductivity, viscosity, thermal diffusivity, Prandtl number, and the dielectric constant for 65 isobars. Quantities of special utility in heat transfer and thermodynamic calculations are also included in the isobaric tables. In addition to the isobaric tables, tables for the saturated vapor and liquid are given, which include all of the above properties, plus the surface tension. Tables for the P-T of the freezing liquid, index of refraction, and the derived Joule-Thomson inversion curve are also presented.

Mccarty, R. D.↗
NASA NTRS1971

A statistical mechanical calculation of the thermodynamic properties of interstitial solid solutions involving second nearest neighbor interactions.

A previous calculation of the thermodynamic properties of interstitial solid solutions based on the technique of Kirkwood expansions has been extended to include the effects of second nearest neighbor solute atom mutual interactions. The error inherent in the first order (or quasi-chemical) counting of the degeneracy of the solution crystal is avoided. It is shown that, at high temperatures, even strong second nearest neighbor solute mutual interactions have a negligible effect on the entropy of the solution and a small, temperature-dependent effect on the solute partial enthalpy.

Alex, K.↗
NASA NTRS1971

Radiative transfer effects on reflected shock waves. I - Transparent gas.

Analytical and numerical calculation of the effects of radiative cooling on the flow field and heat transfer behind a reflected shock wave. The analytical solutions are developed by an expansion procedure about the Newtonian limit - i.e., the flow variables are expanded in the small parameter epsilon representing the initial density ratio across the shock front. Solutions carried out through the zeroth- and first-orders in epsilon show an accuracy to the order of epsilon squared - namely, for the specific conditions considered the analytically calculated enthalpy changes agree to within 2% with the numerically computed changes. The numerical procedure consists of a finite-difference calculation with pressure gradients neglected. The analytical calculations show that pressure-gradient effects may be neglected, except at very long times when the shocked gas has cooled by a large amount. The present calculations show much greater shock-wave attenuation than does a previous numerical computation. This difference is attributed to a better representation of the thermodynamic properties in the present calculations.

Su, F. Y.↗
NASA NTRS1972

A theoretical and experimental investigation of the hypersonic turbulent boundary layer subject to normal and longitudinal pressure gradients and cross flow along a windward plane of symmetry.

A theoretical and experimental investigation for the hypersonic turbulent boundary layer undergoing both normal and longitudinal pressure gradients and cross flow along the plane of symmetry on the windward side of a body of revolution is presented. The purpose of this investigation is to provide a method for calculating boundary layers that occur on the centerline of symmetry of an inlet. The three-dimensional compressible integral equations are written along the symmetry plane and integrated numerically, and the effect of the cross flow on the behavior of the boundary layer is also studied. The experiments were performed at Mach number 6 and Reynolds number of 44,000,000/ft for the axisymmetric case and for the case with cross flow. The velocity profiles and the boundary layer parameters agree relatively well with theoretical values with and without cross flow effects. The presence of the cross flow alters significantly the value of the profiles. Total temperature-velocity correlations deviate from the linear Crocco distribution. Heat transfer rates agree with theoretical values and values obtained by the flat plate reference enthalpy method. Cross flow influence on the heat transfer rates is of minor relevance.

Zakkay, V.↗
NASA NTRS1972

Radiative transfer effects on reflected shock waves. II - Absorbing gas.

Radiative cooling effects behind a reflected shock wave are calculated for an absorbing-emitting gas by means of an expansion procedure in the small density ratio across the shock front. For a gray gas shock layer with an optical thickness of order unity or less the absorption integral is simplified by use of the local temperature approximation, whereas for larger optical thicknesses a Rosseland diffusion type of solution is matched with the local temperature approximation solution. The calculations show that the shock wave will attenuate at first and then accelerate to a constant velocity. Under appropriate conditions the gas enthalpy near the wall may increase at intermediate times before ultimately decreasing to zero. A two-band absorption model yields end-wall radiant-heat fluxes which agree well with available shock-tube measurements.

Su, F. Y.↗
NASA NTRS1972

The turbulent boundary layer on a porous plate - Experimental heat transfer with uniform blowing and suction, with moderately strong acceleration.

Experimental data are presented for heat transfer to the turbulent boundary layer subjected to transpiration and acceleration at constant values of the acceleration parameter K of approximately .00000145. This is a moderately strong acceleration, but not so strong as to result in laminarization of the boundary layer. The results for transpiration fractions F of -0.002, 0.0, and +0.0058 are presented in detail in tabular form, and in graphs of Stanton number versus enthalpy thickness Reynolds number. In addition, temperature profiles at several stations are presented. Stanton number results for F = -0.004, +0.002, and +0.004 are also presented, but in graphical form only. The data were obtained using air as both the free-stream and the transpired fluid, at relatively low velocities, and with temperature differences sufficiently low so that the influence of temperature-dependent fluid properties is minimal. All data were obtained with the surface maintained at a temperature invariant in the direction of flow.

Thielbahr, W. H.↗
NASA NTRS1972

Partially ionized gas flow and heat transfer in the separation, reattachment, and redevelopment regions downstream of an abrupt circular channel expansion.

Heat transfer and pressure measurements obtained in the separation, reattachment, and redevelopment regions along a tube and nozzle located downstream of an abrupt channel expansion are presented for a very high enthalpy flow of argon. The ionization energy fraction extended up to 0.6 at the tube inlet just downstream of the arc heater. Reattachment resulted from the growth of an instability in the vortex sheet-like shear layer between the central jet that discharged into the tube and the reverse flow along the wall at the lower Reynolds numbers, as indicated by water flow visualization studies which were found to dynamically model the high-temperature gas flow. A reasonably good prediction of the heat transfer in the reattachment region where the highest heat transfer occurred and in the redevelopment region downstream can be made by using existing laminar boundary layer theory for a partially ionized gas. In the experiments as much as 90 per cent of the inlet energy was lost by heat transfer to the tube and the nozzle wall.

Back, L. H.↗
NASA NTRS1972

Thermodynamic properties of hydrogen-helium plasmas.

Calculation of the thermodynamic properties of an atomic hydrogen-helium plasma for postulated conditions present in a stagnation shock layer of a spacecraft entering the atmosphere of Jupiter. These properties can be used to evaluate transport properties, to calculate convective heating, and to investigate nonequilibrium behavior. The calculations have been made for temperatures from 10,000 to 100,000 K, densities of 10 to the minus 7th and .00001 g cu cm, and three plasma compositions: pure hydrogen, 50% hydrogen/50% helium, and pure helium. The shock layer plasma consists of electrons, protons, atomic hydrogen, atomic helium, singly ionized helium, and doubly atomized helium. The thermodynamic properties which have been investigated are: pressure, average molecular weight, internal energy, enthalpy, entropy, specific heat, and isentropic speed of sound. A consistent model was used for the reduction of the ionization potential in the calculation of the partition functions.

Nelson, H. F.↗
NASA NTRS1972

Determination of the effects of graphite material properties on ablation performance.

Application of statistical methods to the problem of identifying those material properties of artificial graphite having the strongest effect on ablation performance. Ablation performance, as determined by total length change during test, recession rate, surface temperature, surface texture, and degree of gouging, was measured on 40 different, commercially available, artificial graphites in a Mach 2 airstream having a nominal enthalpy of 2.2 MJ/kg and a stagnation pressure of 5.6 atm. Eighteen material properties were measured on these same graphites, and correlations between pairs of these material properties were developed where possible, reducing the original 18 properties to ten mutually independent properties. Multiple regression equations were formulated relating ablation performance to the reduced set of ten independent material properties, thereby identifying those material properties having the most pronounced effect on ablation performance. These regression equations reveal that for optimum ablation performance in the present environment, grain size should be small, ash content low, density and thermal conductivity high, and mean pore radius large.

Maahs, H. G.↗
NASA NTRS1972

The simulation of high pressure hydrogen/oxygen rocket engines.

Initial experiments have established the feasibility of using a backward running detonation wave in a shock tube to produce the correct enthalpy and chemistry of the simulated combustion chamber gases. This technique produces plume Reynolds numbers higher than those achievable by any other known technique. The practical pressure limitations are being explored and detailed surveys of both single and multiple engine plumes and impingement data on a cylindrical body are being obtained. Facility details to allow safe handling of the high pressure hydrogen and oxygen up to a design chamber pressure of 20,000 psi are described.

Hopkins, H.↗
NASA NTRS1972

Anode heat transfer for a flowing argon plasma at elevated electron temperature.

Theoretical investigation of heat transfer from a preionized gaseous plasma flowing over an anode surface at an elevated electron temperature in the presence of an electric field normal to the surface. A laminar boundary layer is considered in which only the velocity profile is locally similar and fluid properties are assumed to change uniformly in the gas flow direction. Results obtained by an approximation method show that for moderate current densities, the velocity and temperature distributions are insensitive to current. In addition, the effect of elevated electron temperature is negligible on convective heat transfer, but is significant for the overall heat transfer due to the enthalpy transport by current. Total heat flux to the anode is obtained by evaluating the Nusselt number and adding terms due to the potential drop in the sheath and the surface work function.

Bose, T. K.↗
NASA NTRS1972

Simplified analysis and optimization of space base and space shuttle heat rejection systems

A simplified radiator system analysis was performed to predict steady state radiator system performance. The system performance was found to be describable in terms of five non-dimensional system parameters. The governing differential equations are integrated numerically to yield the enthalpy rejection for the coolant fluid. The simplified analysis was extended to produce the derivatives of the coolant exit temperature with respect to the governing system parameters. A procedure was developed to find the optimum set of system parameters which yields the lowest possible coolant exit temperature for either a given projected area or a given total mass. The process can be inverted to yield either the minimum area or the minimum mass, together with the optimum geometry, for a specified heat rejection rate.

Wulff, W.↗
NASA NTRS1972

Thermal performance of 625-kg/cu m elastomeric ablative materials on spherically blunted 0.44-radian cones

Spherically blunted 0.44-radian (25 deg) half-angle conical models coated with elastomeric ablative materials were tested in supersonic arc-heated wind tunnels to evaluate performance of the ablators over a range of conditions typical of lifting entry. Four test conditions were combinations of stagnation point-heat transfer rates of 2.3 and 4.5 MW/m2 and stagnation pressures of 20 and 2kN/m2. Afterbody values of heat transfer rate and pressure were 0.05 to 0.20 of stagnation point values. Stagnation enthalpy varied from 4.4 to 25 MJ/kg (1900 to 11000 Btu/lbm) and free-stream Mach number was in a range from 3.5 to 4. Ablative materials retained the spherical nose shape throughout tests at the lower heat transfer level, but receded, assuming a flattened nose shape, during tests at the high heat transfer level. The residue layer that formed on the conical after-body was weak, friable, and extensively cracked. The reference ablative material, which contained phenolic microspheres, generally retained the conical shape on the model afterbody. However, a modified ablator, in which phenolic microspheres were replaced with silica microspheres, deformed and separated from the undegraded material, and thereby produced a very uneven surface. Substrate temperatures and ablator recession were in good agreement with values computed by a numerical analysis.

Champman, A. J.↗
NASA NTRS1972

Dissociation energies of some high temperature molecules containing aluminum

The Knudsen cell mass spectrometric method has been used to investigate the gaseous molecules Al2, AlSi,AlSiO, AlC2, Al2C2, and AlAuC2. Special attention was given to the experimental considerations and techniques needed to identify and to measure ion intensities for very low abundance molecular species. Second- and third-law procedures were used to obtain reaction enthalpies for pressure calibration independent and isomolecular exchange reactions. Dissociation energies for the molecules were derived from the measured ion intensities, free-energy functions obtained from estimated molecular constants, and auxiliary thermodynamic data. The bonding and stability of these aluminum containing molecules are compared with other similar species.

Stearns, C. A.↗
NASA NTRS1972

Canonical fluid thermodynamics

The space-time integral of the thermodynamic pressure plays the role of the thermodynamic potential for compressible, adiabatic flow in the sense that the pressure integral for stable flow is less than for all slightly different flows. This stability criterion can be converted into a variational minimum principle by requiring the molar free-enthalpy and the temperature, which are the arguments of the pressure function, to be generalized velocities, that is, the proper-time derivatives of scalar spare-time functions which are generalized coordinates in the canonical formalism. In a fluid context, proper-time differentiation must be expressed in terms of three independent quantities that specify the fluid velocity. This can be done in several ways, all of which lead to different variants (canonical transformations) of the same constraint-free action integral whose Euler-Lagrange equations are just the well-known equations of motion for adiabatic compressible flow.

Schmid, L. A.↗