Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EUTECTICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57

Size dependence of microstructure of AlSi10Mg alloy fabricated by selective laser melting

Highlights: • Plate-shaped samples with various widths were fabricated via selective laser melting. • The hardness of AlSi10Mg samples slightly decreased with decreasing sample width. • The alloy sample size had a slight effect on microstructure of the α-Al matrix. • Precipitation of Si phase in α-Al matrix was enhanced by reducing the sample size. • The softening by reducing sample size is likely due to their slower cooling rate. - Abstract: In order to investigate the size dependence of microstructure of the AlSi10Mg alloy fabricated by selective laser melting (SLM) combined with a powder bed technique, plate-shaped AlSi10Mg alloy samples with various widths (ranging from approximately 10 mm to 0.3 mm) were produced in this study. All the fabricated samples exhibited characteristic microstructural morphologies consisting of melt pools with columnar α-Al grains surrounded by fine eutectic Si particles, whereas their sample sizes had a relatively small effect on the texture and average grain size of the α-Al matrix. However, the formation of fine Si precipitates inside the columnar α-Al grains was observed more often for the smaller-sized samples, which could be a possible dominant contributor to the observed softening of the sample by reducing sample size. The obtained results were utilized for discussing the size dependence of the strength of the SLM-manufactured porous alloy samples.

36 MATERIALS SCIENCE↗

Effect of Bi on the microstructure and mechanical properties of Sn-Zn alloys processed by rolling

Highlights: • Sn-Zn-Bi is proposed for the first time as the cladding in linear explosive device. • Bi can significantly refine the microstructure of Sn-Zn. • Bi can enhance both strength and ductility of Sn-Zn processed by rolling. • The 5 wt% Bi in Sn-3Zn leads to finest and most homogenous grains after rolling. - Abstract: Sn-Zn based alloys including Sn-3Zn, Sn-3Zn-1Bi, and Sn-3Zn-5Bi were prepared by casting and rolling, in efforts to assess their feasibility for the application as cladding materials in detonating and explosive cords. It was found that Bi significantly refined the solidification microstructure, changing the configuration of Sn-Zn eutectic from well-aligned Zn-rich precipitates/needles to misaligned Zn-rich flakes. During deformation, second phases like Zn-rich precipitates and Bi particles, and Bi solutes were effective in grain refinement since second phase particles provided more sites for nucleation and more obstacles to growth of new recrystallized grains. Tensile results revealed that Bi addition enhanced both strength and ductility of the rolled Sn-Zn-Bi alloys. The Sn-3Zn-5Bi alloy possessed superior strength and ductility (UTS: 84.4 MPa; Yield strength: 68.3 MPa; Elongation: 75.2%) due to its finest and most homogeneous equiaxed grains. Based on decent mechanical properties, the Sn-Zn-Bi alloys could be well qualified for the application as cladding materials.

36 MATERIALS SCIENCE↗

Low cycle fatigue behavior of AlSi10Mg(Cu) alloy at high temperature

Highlights: • The cyclic stress response of AlSi10Mg(Cu) alloy in LCF regime is temperature-dependent. • Precipitates transitions were observed after high temperature cycle loading. • Changes in the interaction mechanism between dislocations and nanoparticles lead to different cyclic stress responses. - Abstract: Low cycle fatigue (LCF) behavior of AlSi10Mg(Cu) alloy was investigated at 100 °C and 250 °C over a range of strain amplitude from 0.25% to 0.40%. Cycle stress response, hysteresis loops, fatigue life, as well as post-fatigue microstructure were studied in detail. Except 0.25%, the alloy performed cycle hardening behavior at 100 °C and softening behavior at 250 °C at any given strain amplitude, which corresponded well with the observed phenomena in hysteresis loops. At any given temperature, cyclic stress increases while fatigue life decreases with the increasing strain amplitude. The fatigue life of the studied alloy at 100 °C was higher than that at 250 °C under the same strain amplitude. Fractography indicated that most fatigue crack initiated from casting defects. The fatigue crack propagation was mainly characterized by fatigue striations and tear ridges in any conditions. Section inspection shows that the number of cracked eutectic Si increases with decreasing the temperature or increasing strain amplitude. Post-mortem transmission electron microscopy (TEM) investigations indicated that cyclic hardening behavior at 100 °C was due to the pinning effect of coherent precipitates (β″-Mg{sub 2}Si and GP zones). Most of tiny coherency precipitates and clusters transformed to large semi-coherency Q′ and β′-Mg{sub 2}Si precipitates after cyclic loading at 250 °C, leading to the sharp decrease of pinning number and dislocation density, which is a key reason for the cyclic softening. Another factor is that more dislocations can be activated and dislocation climb is easier at higher temperature.

36 MATERIALS SCIENCE↗

Thermoelectric properties of BiSbTe-type alloys prepared by chill-casting and cryo-milling

The thermoelectric properties of Bi x Sb 1-x Te 3 processed through milling have been extensively studied with varied results that needs to be rationalized. Since cryo-milling is a relatively cleaner milling process compared to other milling processes, in this study we explore this technique to reduce the particle size prior to compaction to get an insight into the thermoelectric properties. We first report the results of cryomilled BiSbTe 3 compacted by spark plasmas sintering (SPS) process and show that milling leads to a change in transport behavior from ‘p’ to ‘n’ type similar to that reported for Bi 2 Te 3 . It is shown that the defects induced by milling is responsible for this change in materials behavior. We further study the effect of change in Bi to Sb ratio and excess tellurium on the thermoelectric properties when processed through cryo-milling as well as casting using a chilled copper block. Excess tellurium leads to a microstructure containing a fraction of layered eutectic that gets further fragmented during cryo-milling. Although the Seebeck coefficient does not change significantly, reflecting the cleanliness of the process, the thermal conductivity changes during hot compaction leading to an improvement of ZT. However, a comparison of all the reported results does not reveal any systematics in thermoelectric properties reflecting the difficulties with these materials.

36 MATERIALS SCIENCE↗

High damping NiTi/Ti 3 Sn in situ composite with transformation-mediated plasticity

The concept of transformation-induced plasticity effect is introduced in this work to improve the plasticity of brittle intermetallic compound Ti3Sn, which is a potent high damping material. This concept is achieved in an in situ NiTi/Ti3Sn composite. The composite is composed of primary Ti3Sn phase and (NiTi + Ti3Sn) eutectic structure formed via hypereutectic solidification. The composite exhibits a high damping capacity of 0.075 (indexed by tan δ), a high ultimate compressive strength of 1350 MPa, and a large plasticity of 27.5%. In situ synchrotron high-energy X-ray diffraction measurements revealed clear evidence of the stress-induced martensitic transformation (B2 → B19) of the NiTi component during deformation. The strength of the composite mainly stems from the Ti3Sn, whereas the NiTi component is responsible for the excellent plasticity of the composite.

Composite↗

Chemical partitioning for the Co--Pr system: First-principles, experiments and energetic calculations to investigate the hard magnetic phase

Co 5 Pr-D2 d is promising permanent magnet. Due to its peritectic formation feature, there is a synthetic challenge to produce single Co 5 Pr-D2 d phase. The object of our study is to assess thermodynamic pathways for crystalline phases under far-from-equilibrium conditions by combining first-principles calculations and experimental measurements into a robust description of the thermodynamic behavior. The energetic calculations, temperature and time dependent phase selections are predicted under varying degrees of chemical partitioning. Our calculation to assess the chemical partitioning-temperatures indicates that the major magnetic compounds: Co 17 Pr 2 -α, Co 5 Pr-D2 d , Co 19 Pr 5 -β, and Co 7 Pr 2 -χ form from a congruent manner to eutectic reactions with decreasing cooling rate. The compositions of the compounds from these highly driven liquids can be far from equilibrium.

36 MATERIALS SCIENCE↗

Mechanism of heat affected zone cracking in Ni-based superalloy DZ125L fabricated by laser 3D printing technique

Laser 3D printing is a promising technique to repair damaged Ni-based superalloy components. However, the occurrence of heat affected zone (HAZ) cracking severely limits its applicability. In this paper, we unravel the cracking mechanism by studying the element, phase, defect, and strain distribution around an intergranular crack that initiated from the primary HAZ. Using synchrotron X-ray Laue microdiffraction, we measured high tensile strain/stress transverse to the building direction in both the primary HAZ and the cladding layers, as well as high-density dislocations, which resulted from the thermal contraction and rapid precipitation of γ' phase. The crack initiated because the transverse tensile strain/stress tore up the liquid film formed by the low-melting point preexisting phases in the primary HAZ, such as γ/γ' eutectics and coarse γ' precipitates. The incoherent carbide particles were frequently observed near the crack root as local strain concentrators. In the cladding layers, micro-segregation could not be completely avoided, thus the hot crack continued to propagate over several layers with the assistance of the transverse tensile stress. Finally, our investigations provide a useful guideline for the optimization of the 3D printing process to repair Ni-based superalloys with high susceptibility to hot cracking.

36 MATERIALS SCIENCE↗

Multimodal and multiscale strengthening mechanisms in Al-Ni-Zr-Ti-Mn alloy processed by laser powder bed fusion additive manufacturing

The unique thermokinetics of laser-powder bed fusion additive manufacturing (L-PBFAM) has been exploited for development of a novel high-strength Al-Ni-Ti-Zr-Mn alloy. The addition of 0.5 wt% Mn leads to extraordinary improvement in ultimate tensile strength (502 MPa) and work hardening due to the activation of two Mn-induced strengthening mechanisms. First, by a bimodal particle strengthening effect due to Al 31 Mn 6 Ni 12 nano-quasi-crystal particles rejected in inter-dendritic spaces and fibrous Al 3 Ni eutectic dendritic channels, which predominately contributes to the strength improvement, and second by solid solution strengthening from remaining Mn entrapped in Al. These mechanisms supplement the particle strengthening effect imparted by coherent and incoherent Al 3 (Ti,Zr) co-precipitates present at melt pool boundaries, dislocation strengthening due to solidification induced strain, and Hall-Petch and backstress strengthening effect due to heterogenous grain size distribution occurring at various length scales. In conclusion, the solidification dynamics and hierarchical heat distribution that are associated with L-PBFAM resulted in complex spatial variations in these strengthening phenomena and were investigated via a high-throughput multiscale structure–property correlation that involved thermokinetic simulation, X-ray diffraction, high-resolution nanoindentation mapping, and site-specific transmission electron microscopy of the alloy.

36 MATERIALS SCIENCE↗

Surface smoothing for laser powder-bed Ti-6Al-4V by a transient liquid phase

Surface roughness is the primary driver of fatigue for additively manufactured metals. To address surface roughness, this work introduces a new method to smooth features beyond line-of-sight without material removal. The method applies a coating that triggers local surface remelting by activating a eutectic reaction during heat treatment. The associated liquid phase then wets and isothermally solidifies into a smoother surface. For Ti-6Al-4V fabricated with laser powder bed fusion, samples with and without TLP smoothing (using a Cu coating) were characterized with a suite of techniques, including mechanical testing, electron backscatter diffraction, synchrotron X-ray tomography, and fractography. TLP smoothing reduced surface roughness by 80% and amplified compressive residual stress at the surface by about 50%. With statistically equivalent virtual microstructures, crystal plasticity scrutinized the roles of phases, porosity, and surface roughness. Although the tensile strain-to-failure was reduced to 1% strain, the TLP smoothing process increased high-cycle fatigue strength by about 20% compared to control samples, pointing to future opportunities to optimize the new process through various coating compositions and heat treatment schedules. Overall, this work establishes a new paradigm for treating surfaces of materials for smoothness and compressive residual stress.

Additive manufacturing↗

Ion exchange and electrochemical evaluation of the microporous phosphate Li{sub 9}Fe{sub 7}(PO{sub 4}){sub 10}

A new lithium iron(III) phosphate, Li{sub 9}Fe{sub 7}(PO{sub 4}){sub 10}, has been synthesized and is currently under electrochemical evaluation as an anode material for rechargeable lithium-ion battery applications. The sample was prepared via the ion exchange reaction of Cs{sub 5}K{sub 4}Fe{sub 7}(PO{sub 4}){sub 10}1 in the 1 M LiNO{sub 3} solution under hydrothermal conditions at 200 deg. C. The fully Li{sup +}-exchanged sample Li{sub 9}Fe{sub 7}(PO{sub 4}){sub 10}2 cannot yet be synthesized by conventional high-temperature, solid-state methods. The parent compound 1 is a member of the Cs{sub 9-x}K{sub x}Fe{sub 7}(PO{sub 4}){sub 10} series that was previously isolated from a high-temperature (750 deg. C) reaction employing the eutectic CsCl/KCl molten salt. The polycrystalline solid 1 was first prepared in a stoichiometric reaction via conventional solid-state method then followed by ion exchange giving rise to 2. Both compounds adopt three-dimensional structures that consist of orthogonally interconnected channels where electropositive ions reside. It has been demonstrated that the Cs{sub 9-x}K{sub x}Fe{sub 7}(PO{sub 4}){sub 10} series possesses versatile ion exchange capabilities with all the monovalent alkali metal and silver cations due to its facile pathways for ion transport. 1 and 2 were subject to electrochemical analysis and preliminary results suggest that the latter can be considered as an anode material. Electrochemical results indicate that Li{sub 9}Fe{sub 7}(PO{sub 4}){sub 10} is reduced below 1 V (vs. Li) to most likely form a Fe(0)/Li{sub 3}PO{sub 4} composite material, which can subsequently be cycled reversibly at relatively low potential. An initial capacity of 250 mAh/g was measured, which is equivalent to the insertion of thirteen Li atoms per Li{sub 9+x}Fe{sub 7}(PO{sub 4}){sub 10} (x = 13) during the charge/discharge process (Fe{sup 2+} + 2e {yields} Fe{sup 0}). Furthermore, 2 shows a lower reduction potential (0.9 V), by approximately 200 mV, and much better electrochemical reversibility than iron(III) phosphate, FePO{sub 4}, highlighting the value of improving the ionic conductivity of the sample.

36 MATERIALS SCIENCE↗

Growth of PbTe nanorods controlled by polymerized tellurium anions and metal(II) amides via composite-hydroxide-mediated approach

The pure face-centered-cubic PbTe nanorods have been synthesized by the composite-hydroxide-mediated approach using hydrazine as a reducing agent. The method is based on reaction among reactants in the melts of potassium hydroxide and sodium hydroxide eutectic at 170-220 deg. C and normal atmosphere without using any organic dispersant or surface-capping agent. Scanning electron microscopy, X-ray diffraction, transmission electron microscopy, and energy dispersive X-ray spectroscopy were used to characterize the structure, morphology and composition of the samples. The diameters of nanorods are almost fixed, while the lengths can be tunable under different growth time and temperatures. The growth mechanism of PbTe nanorods is investigated via UV-vis absorption, demonstrating that polymerized tellurium anions and metal(II) amides in the hydrazine hydroxide melts could control the crystallization and growth process of PbTe nanostructures. The band gap of as-synthesized PbTe nanorods has been calculated based on UV-vis-NIR optical diffuse reflectance spectra data.

36 MATERIALS SCIENCE↗

Thermodynamic assessment of lithium halide reciprocal salt systems for energy applications

Lithium halides are of interest because of their unique applications as fuel or coolants in molten salt reactors (MSRs) and electrolytes in thermally activated batteries. Because iodine is an important fission product for MSRs, the Molten Salt Thermal Properties Database-Thermochemical (MSTDB-TC) is being expanded to include relevant iodide reciprocal salt systems. In this work, we assess the thermochemical properties of lithium halide pseudobinary systems based on reported experimental phase diagrams, eutectic temperatures, and enthalpies of mixing. Within the framework of the modified quasi-chemical model in the quadruplet approximation (MQMQA), extrapolations to the related pseudoternary and pseudoquaternary systems have been performed. The pseudoquaternary representations of phase equilibria, enthalpy, entropy, and heat capacity are represented in the resultant models. Of interest for generating source terms for accident analysis is the ability to compute the vapor pressures of the dominant iodide species for the systems at any composition. Here, an example of such calculations is provided for the LiF-LiI system at x LiI = 0.01 and x LiI = 0.70, in this case indicating that the LiI vapor species are predominant.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Thermophysical properties of FLiBe using moment tensor potentials

Fluoride salts are prospective materials for applications in some next-generation nuclear reactors and their thermophysical properties at various conditions are of interest. Experimental measurement of the properties of these salts is often difficult and, in some cases, unfeasible due to challenges from high temperatures, impurity control, and corrosivity. Therefore, accurate theoretical methods are needed for fluoride salt property prediction. In this work, we used moment tensor potentials (MTP) to approximate the potential energy surface of eutectic FLiBe (66.6% LiF – 33.3% BeF2) predicted by the ab initio (DFT-D3) method. Here, we then used the developed potential and molecular dynamics to obtain several thermophysical properties of FLiBe, including radial distribution functions, density, self-diffusion coefficients, thermal expansion, specific heat capacity, bulk modulus, viscosity, and thermal conductivity. Our results show that the MTP potential approximates the potential energy surface accurately and the overall approach yields very good agreement with experimental values. The converged fitting can be obtained with less than 600 configurations generated from DFT calculations, which data can be generated in just 1200 core hours on today's typical processors. The MTP potential is faster than many machine learning potentials and about one order of magnitude slower than widely used empirical molten salt potentials such as Tosi/Fumi.

36 MATERIALS SCIENCE↗

Synthesis and thermophysical property determination of NaCl-PuCl3 salts

Currently, a knowledge gap exists in the available data and understanding of thermophysical properties relating to fresh fuel salts, especially those containing plutonium. These data are necessary for designing, constructing, and licensing future commercial molten-salt reactors. Thermophysical properties, such as melting temperature, salt stability, density, and heat capacity were ascertained using NaCl-PuCl3 (36 mol% PuCl3) and a more sodium rich composition containing 25 mol% PuCl3. The NaCl-PuCl3 salt mixture was synthesized for this study and contained 63.4 mol% NaCl, 36.3 mol% PuCl3 and was 99.7% pure. Upon heating, the NaCl–PuCl3 eutectic was stable at temperatures up to 800 °C. The onset of melting occurred at 451 ± 3 °C, and the enthalpy of fusion was determined to be 23.0 ± 1.4 kJ/mol. Heat capacity measurements in the liquid phase ranged from 107.7 to 91.3 J/mol.K, with an average value of 104.6 ± 11.4 J/mol.K between 500 and 650 °C. Three independent trials of the molten NaCl-PuCl3 salt found the density to be ?(T) = 3.8589 – 9.5342·10-4 T(°C). In addition, ab initio molecular dynamic simulations to calculate density and heat capacity values are included.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Predicting thermophysical properties of molten salts in the MgCl 2 -NaCl-KCl-LiCl system with a shell-model potential

Ternary eutectic salts composed of MgCl 2 , NaCl, and KCl, referred to as MNK salts, have recently emerged as promising candidates as high-temperature heat transfer fluids and thermal energy storage media. Here we performed classical molecular dynamics (MD) simulations to predict the densities, specific heat capacities, viscosities, and ionic self-diffusivities for MNK salts over a wide temperature range. The impact of LiCl additive on their thermophysical properties was also investigated. To capture the electronic polarization of Cl anions by neighboring cations, we developed a novel shell-model potential using the force-matching method and a dataset of ab initio calculated interatomic forces. Our extensive MD simulations predict structure and properties for pure salts and binary/ternary salt mixtures in the MgCl 2 -NaCl-KCl-LiCl system in overall good agreement with available experimental and theoretical data, which corroborates the accuracy and reliability of our developed potential.

36 MATERIALS SCIENCE↗

Effect of iodides on thermal behavior and phase partitioning in LiCl-KCl

Liquid-fueled molten salt reactors (MSRs) are designed to operate with fissile materials and, ultimately, fission products dissolved in the primary molten salt coolant. Understanding the speciation and transport of iodine—a high-yield fission product—is essential because this element’s accidental release poses significant environmental concerns due to its capacity to be readily absorbed by the human thyroid gland. Here, we report the impact of iodide species (LiI and KI) on phase transitions, phase distribution, and phase stability in LiCl–KCl-eutectic salt mixtures. The study employed a combination of computational and experimental techniques, including thermodynamic FactSage calculations, differential scanning calorimetry, and high-temperature X-ray diffraction. The results indicate that the presence of iodide (10–25 wt%) significantly alters the melting behavior of the LiCl–KCleutectic system. Adding 10 wt% LiI has a more-pronounced effect than 10 wt% KI, as LiI converts to KI, leading to formation of LiCl, thereby, altering the LiCl-KCl ratio which significantly affects the melting temperature of the mixture. Furthermore, the evolution of crystalline structure, solid-fraction composition, and the dynamics of mixed-halide solid–liquid partitioning as a function of temperature indicate the potential for selective iodide separation from chloride-salt mixtures via solid–liquid separation techniques. Overall, the presented findings provide valuable insights that are beneficial for the design and operation of MSRs, as well as for the safe handling and effective processing of used nuclear fuel using advanced pyrochemical techniques.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructural refinement of an Al-Ce-Mg alloy via Shear Assisted Processing and Extrusion

Al-Ce alloys have attracted recent interest because of their high thermal stability due to the low solubility of Ce in the Al matrix. The Al 11 Ce 3 eutectic phase gives excellent strain hardening behavior and moderate high-temperature strength in the as-cast state. However, its strengthening effect is limited by its coarse as-cast structure. Therefore, alternative manufacturing methods such as additive manufacturing or equal channel angular pressing have been applied to refine the Al 11 Ce 3 phase to good effect. However, these techniques are both expensive and time-consuming. Therefore, this study aims to use Shear Assisted Processing and Extrusion (ShAPE), an emerging solid phase processing technique that is more easily scalable than the previously mentioned methods. ShAPE can produce useful cross-sections of an Al-8Ce-4Mg alloy while refining the Al 11 Ce 3 phase to produce a higher strength material. It was found that a low temperature ShAPE process can improve the room temperature yield strength by ~60 % compared to a binary Al-4Mg alloy. Additionally, the high-temperature yield strength of the Al-Ce alloys increased by 20%, with a simultaneous 15% improvement in ductility compared to the binary Al-Mg alloy. Finally, these results highlight the potential for ShAPE as a processing technique for Al-Ce alloys.

36 MATERIALS SCIENCE↗

Effect of Si impurities on microstructure and tensile properties of a cast Al-Mg-Fe alloy

Al-Mg alloys are attractive for structural castings owing to their superior strength and ductility in the as-cast state. However, given the tight tolerance for impurities, Al-Mg alloys produced from secondary sources still face multiple challenges. Here, we report the effect of increased Si impurity (0.05–1.6 wt%), which is commonly found in secondary Al sources, on microstructure and tensile properties of a cast Al-4.3Mg-1.6Fe (wt%) alloy, commercially referred to as Castaduct-42 alloy. Microstructural characterization revealed that Si addition increased the volume fraction, size, and aspect ratio of primary Al13Fe4 intermetallic particles as well as the volume fraction of other binary and ternary eutectic phases. Tensile testing results demonstrated that increasing Si impurities from 0.05 to 1.6 wt% reduced ductility from 14.3 ± 1.4 % to 2.2 ± 1.0 %. A particle cracking damage accumulation model coupled with failure analysis indicated primary Al13Fe4 intermetallic particles to be the major contributing factor to the deterioration in ductility with increasing Si content. Additionally, the stabilizing effect of Si on primary Al 13 Fe 4 was inconsistent with the CALPHAD calculation results based on existing CALPHAD databases which predict a slightly decreasing primary Al13Fe4 phase fraction with increasing Si concentration. This work provides new insights into the phase stability and mechanical behavior of the lesser studied Al-Mg-Fe-Si alloy system that will contribute to the development of sustainable cast Al-Mg based alloys.

36 MATERIALS SCIENCE↗