Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Dendrites”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Morphology and composition of chalcopyrite, chromite, Cu, Ni-Fe, pentlandite, and troilite in vugs of 76015 and 76215

Vugs from 76015 and 76215 are lined with euhedral crystals of plagioclase, pyroxene, ilmenite, Ni-Fe, and troilite. Smaller crystals of chromite, pentlandite, and chalcopyrite occur on the surface of the troilite in 76015. Wire Cu and dendritic-metallic Cu occurs with metallic Ni-Fe and troilite in some vugs of 76215. Troilite in both samples may have crystallized from an immiscible sulfide liquid. With falling temperature, chalcopyrite, and pentlandite may have exsolved from the troilite in 76015. By contrast, metallic Cu may have formed in 76215 by thermal breakdown of a bornite, troilite, and Ni-Fe assemblage which originally crystallized from a low-Ni immiscible sulfide liquid.

Carter, J. L.↗
NASA NTRS1978

Laser-zone growth in a Ribbon-To-Ribbon (RTR) process. Silicon sheet growth development for the large area sheet task of the low-cost solar array project

A new calculation of the effects of thermal stresses during growth on silicon ribbon quality is reported. Thermal stress distributions are computed for ribbon growth under a variety of temperature profiles. A growth rate of 55 cu cm/min with a single ribbon was achieved. The growth of RTR ribbon with a fairly uniform parallel dendritic structure was demonstrated. Results with two approaches were obtained for reducing the Mo impurity level in polycrystalline feedstock. Coating the Mo substrate with Si3N4 does not effect thermal shear separation of the polyribbon; this process shows promise of improving cell efficiency and also increasing the useful life of the molybdenum substrate. A number of solar cells were fabricated on RTR silicon grown from CVD feedstock.

Baghdadi, A.↗
NASA NTRS1979

Silicon on Ceramic Process: Silicon Sheet Growth and Device Development for the Large-area Silicon Sheet and Cell Development Tasks of the Low-cost Solar Array Project

The technical and economic feasibility of producing solar cell quality sheet silicon was investigated. It was hoped this could be done by coating one surface of carbonized ceramic substrates with a thin layer of large-grain polycrystalline silicon from the melt. Work was directed towards the solution of unique cell processing/design problems encountered with the silicon-ceramic (SOC) material due to its intimate contact with the ceramic substrate. Significant progress was demonstrated in the following areas; (1) the continuous coater succeeded in producing small-area coatings exhibiting unidirectional solidification and substatial grain size; (2) dip coater succeeded in producing thick (more than 500 micron) dendritic layers at coating speeds of 0.2-0.3 cm/sec; and (3) a standard for producing total area SOC solar cells using slotted ceramic substrates was developed.

Chapman, P. W.↗
NASA NTRS1979

Silicon-on-ceramic Process: Silicon Sheet Growth and Device Development for the Large-area Silicon Sheet and Cell Development Tasks of the Low-cost Solar Array Project

Significant progress is reported in fabricating a 4 sq cm cell having a 10.1 percent conversion efficiency and a 10 sq cm cell having a 9.2 percent conversion efficiency. The continuous (SCIM) coater succeeded in producing a 16 sq cm coating exhibiting unidirectional solidification and large grain size. A layer was grown at 0.2 cm/sec in the experimental coater which was partially dendritic but also contained a large smooth area approximately 100 micron m thick. The dark characteristic measurements of a typical SCC solar cell yield shunt resistance values of 10K ohms and series resistance values and 0.4 ohm. The production dip-coater is operating at over 50 percent yield in terms of good cell quality material. The most recent run yielded 13 good substrates out of 15.

Chapman, P. W.↗
NASA NTRS1979

Silicon web process development

Silicon dendritic web, a single crystal ribbon shaped during growth by crystallographic forces and surface tension (rather than dies), is a highly promising base material for efficient low cost solar cells. The form of the product smooth, flexible strips 100 to 200 microns thick, conserves expensive silicon and facilitates automation of crystal growth and the subsequent manufacturing of solar cells. These characteristics, coupled with the highest demonstrated ribbon solar cell efficiency-15.5%-make silicon web a leading candidate to achieve, or better, the 1986 Low Cost Solar Array (LSA) Project cost objective of 50 cents per peak watt of photovoltaic output power. The main objective of the Web Program, technology development to significantly increase web output rate, and to show the feasibility for simultaneous melt replenishment and growth, have largely been accomplished. Recently, web output rates of 23.6 sq cm/min, nearly three times the 8 sq cm/min maximum rate of a year ago, were achieved. Webs 4 cm wide or greater were grown on a number of occassions.

Duncan, C. S.↗
NASA NTRS1979

Silicon Web Process Development

Silicon dendritic web, ribbon form of silicon and capable of fabrication into solar cells with greater than 15% AMl conversion efficiency, was produced from the melt without die shaping. Improvements were made both in the width of the web ribbons grown and in the techniques to replenish the liquid silicon as it is transformed to web. Through means of improved thermal shielding stress was reduced sufficiently so that web crystals nearly 4.5 cm wide were grown. The development of two subsystems, a silicon feeder and a melt level sensor, necessary to achieve an operational melt replenishment system, is described. A gas flow management technique is discussed and a laser reflection method to sense and control the melt level as silicon is replenished is examined.

Duncan, C. S.↗
NASA NTRS1979

Silicon-on Ceramic Process: Silicon Sheet Growth and Device Development for the Large-area Silicon Sheet and Cell Development Tasks of the Low-cost Solar Array Project

The technical and economic feasibility of producing solar cell-quality silicon was investigated. This was done by coating one surface of carbonized ceramic substrates with a thin layer of large-grain polycrystalline silicon from the melt. Significant progress in the following areas was demonstrated: (1) fabricating a 10 sq cm cell having 9.9 percent conversion efficiency; (2) producing a 225 sq cm layer of sheet silicon; and (3) obtaining 100 microns thick coatings at pull speed of 0.15 cm/sec, although approximately 50 percent of the layer exhibited dendritic growth.

Chapman, P. W.↗
NASA NTRS1979

Rates and processes of crystal growth in the system anorthite-albite

The growth rates and interface morphologies of crystals of synthetic compositions in the anorthite (CaAl2Si2O8)-albite (NaAlSi3O8) plagioclase feldspar system are measured in an investigation of the crystallization of igneous rocks. Mixed plagioclase glasses with compositions of 75% and 50% anorthite were observed using the microscope heating technique as they crystallized at temperatures near the liquidus, and 75%, 50% and 20% anorthite crystals were treated by resistance heating and observed at greater degrees of undercooling. Growth rates were found to be independent of time and to decrease with increasing albite content, ranging from 0.5 to 2 x 10 to the -5th cm/min. The crystal morphologies for all compositions are faceted near the liquidus and become progressively skeletal, dendritic and fibrillar with increasing undercooling.

Kirkpatrick, R. J.↗
NASA NTRS1979

Silicon Solar Cell Process Development, Fabrication and Analysis, Phase 1

Solar cells from RTR ribbons, EFG (RF and RH) ribbons, dendritic webs, Silso wafers, cast silicon by HEM, silicon on ceramic, and continuous Czochralski ingots were fabricated using a standard process typical of those used currently in the silicon solar cell industry. Back surface field (BSF) processing and other process modifications were included to give preliminary indications of possible improved performance. The parameters measured included open circuit voltage, short circuit current, curve fill factor, and conversion efficiency (all taken under AM0 illumination). Also measured for typical cells were spectral response, dark I-V characteristics, minority carrier diffusion length, and photoresponse by fine light spot scanning. the results were compared to the properties of cells made from conventional single crystalline Czochralski silicon with an emphasis on statistical evaluation. Limited efforts were made to identify growth defects which will influence solar cell performance.

Yoo, H. I.↗
NASA NTRS1980

Rechargeable ambient temperature lithium cells

The cycling performance of a secondary lithium cell with a 2-methyl THF lithium hectofluorarsenate electrolyte is discussed. Stripping efficiency, dendritization, passivation on standing, and discharge efficiency are considered.

Holleck, G. L.↗
NASA NTRS1979

Phase 2 of the array automated assembly task for the low cost solar array project

The process sequence for the fabrication of dendritic web silicon into solar panels was modified to include aluminum back surface field formation. Plasma etching was found to be a feasible technique for pre-diffusion cleaning of the web. Several contacting systems were studied. The total plated Pd-Ni system was not compatible with the process sequence; however, the evaporated TiPd-electroplated Cu system was shown stable under life testing. Ultrasonic bonding parameters were determined for various interconnect and contact metals but the yield of the process was not sufficiently high to use for module fabrication at this time. Over 400 solar cells were fabricated according to the modified sequence. No sub-process incompatibility was seen. These cells were used to fabricate four demonstration modules. A cost analysis of the modified process sequence resulted in a selling price of $0.75/peak watt.

Campbell, R. B.↗
NASA NTRS1980

Space Processing Application Rocket project, SPAR 5

Post flight results and analysis are presented on the following experiments: 'Agglomeration in Immiscible Liquids', 'Contained Polycrystalline Solidification in Low G', 'The Direct Observation of Dendrite Remelting and Macrosegregation in Casting', and 'Uniform Dispersion by Crystallization'. An engineering report on the performance of the SPAR Black Brant rocket is also included. Much useful data and information were accumulated for directing and developing experimental techniques and investigations toward an expanding commercially beneficial program of materials processing in the coming shuttle era.

Reeves, F.↗
NASA NTRS1980

The effect of reduced gravity on solidification microstructures of NH4Cl-H2O alloys

The effect of gravity on the columnar-to-equiaxed microstructural transition was studied in small samples of NH4Cl-H2O. The behavior of the samples during laboratory (one gravity) experiments was contrasted with their behavior during a (low gravity) sounding rocket flight. In one gravity, the columnar zone accounted for 25 to 100 pct of the structure, depending on the superheat and orientation of the chill. Grain multiplication occurred by showering and by convection induced dendrite arm remelting. Convection was caused by both thermal gradients and solutal gradients. In low gravity, however, completely columnar structures were obtained; all grain multiplication mechanisms were entirely suppressed. Reduced gravity also modified the thermal conditions and caused the liquid to cool more slowly. This resulted in a steeper temperature gradient in the liquid ahead of the solidification interface. 'Big bang' type nucleation occurred in two of the samples, distributing nuclei throughout the liquid. Despite this, an equiaxed zone did not form, indicating that the most significant effect of low gravity on this experiment was modification of the thermal conditions.

Papazian, J. M.↗
NASA NTRS1980

Defect structure of web silicon ribbon

The results of a preliminary study of two dendritic web samples are presented. The structure and electrical activity of the defects in the silicon webs were studied. Optical microscopy of chemically etched specimens was used to determine dislocation densities. Samples were mechanically polished, then Secco etched for approximately 5 minutes. High voltage transmission electron microscopy was used to characterize the crystallographic nature of the defects.

Cunningham, B.↗
NASA NTRS1980

Silicon Research and Technology Workshop report

The materials, structures, processing, modeling and measurements of high efficiency silicon solar cells were surveyed. In the materials area, highlights included: (1) the possibility of improving cell voltages by reducing minority carrier mobilities in critical regions of the solar cells; (2) the need for and possibility of lowering the surface recombination velocity for improvement of open circuit voltage in shallow junction cells; (3) the present need for improved lifetime in high resistivity cells; and (4) the potential for new materials such as polycrystalline or dendritic web material to perform well at end of life in a radiation environment. In the area of structures, distinction was made between those for terrestrial use and those that would survive radiation environments. Areas such as epitaxial growth and laser or elctron beam annealing (and diffusion) were proposed as having certain advantages over more conventional techniques.

Meulenberg, A., Jr.↗
NASA NTRS1981

The growth of metastable peritectic compounds

The influence of gravitationally driven thermosolutal convection on the directional solidification of peritectic alloys is considered as well as the relationships between the solidification processing conditions, and the microstructure, chemistry, and magnetic properties of such alloys. Analysis of directionally solidified Pb-Bi peritectic samples indicates that appreciable macrosegregation occurs due to thermosolutal convection and/or Soret diffusion. A peritectic solidification model which accounts for partial mixing in the liquid ahead of the planar solidification interface and describes macrosegregation has been developed. Two-phase dendritic and banded microstructures were grown in the Pb-Bi peritectic system, refined two-phase microstructures have were observed, and candidate formation mechanisms proposed. Material handling, containment, casting, microstructural and magnetic characterization techniques were developed for the Sm-Co system. Alloys produced with these procedures are homogeneous.

Larson, D. J., Jr.↗
NASA NTRS1981

Silicon solar cell process development, fabrication and analysis

The fabrication of solar cells from several unconventional silicon materials is described, and cell performance measured and analyzed. Unconventional materials evaluated are edge defined film fed grown (EFG), heat exchanger method (HEM), dendritic web grown, and continuous CZ silicons. Resistivity, current voltage, and spectral sensitivity of the cells were measured. Current voltage was measured under AM0 and AM1 conditions. Maximum conversion efficiencies of cells fabricated from these and other unconventional silicons were compared and test results analyzed. The HEM and continuous CZ silicon were found to be superior to silicon materials considered previously.

Minahan, J. A.↗
NASA NTRS1981

Low cost solar array project production process and equipment task. A Module Experimental Process System Development Unit (MEPSDU)

Technical readiness for the production of photovoltaic modules using single crystal silicon dendritic web sheet material is demonstrated by: (1) selection, design and implementation of solar cell and photovoltaic module process sequence in a Module Experimental Process System Development Unit; (2) demonstration runs; (3) passing of acceptance and qualification tests; and (4) achievement of a cost effective module.

Source record↗