Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Control design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57

Criteria for design of integrated flight/propulsion control systems for STOVL fighter aircraft

As part of NASA's program to develop technology for short takeoff and vertical landing (STOVL) fighter aircraft, control system designs have been developed for a conceptual STOVL aircraft. This aircraft is representative of the class of mixed-flow remote-lift concepts that was identified as the preferred design approach by the U.S./U.K. STOVL Joint Assessment and Ranking Team. The control system designs have been evaluated throughout the powered-lift flight envelope on the Vertical Motion Simulator (VMS) at Ames Research Center. Items assessed in the control system evaluation were: maximum control power used in transition and vertical flight, control system dynamic response associated with thrust transfer for attitude control, thrust margin in the presence of ground effect and hot-gas ingestion, and dynamic thrust response for the engine core. Effects of wind, turbulence, and ship airwake disturbances are incorporated in the evaluation. Results provide the basis for a reassessment of existing flying-qualities design criteria applied to STOVL aircraft.

Franklin, James A.↗

The Interplay Between Hardware and Control System Design in the Development of the Active Rack Isolation System

A primary mission of the International Space Station (ISS) is to provide a premier microgravity laboratory environment for conducting acceleration sensitive scientific research. In order to accomplish this goal, vibroacoustic disturbances caused by station activities that occur during the microgravity mode of operation, must be controlled. In addition to source isolation and other passive isolation methods, the ISS uses active isolation at the receiver, through the use of an Active Rack Isolation System (ARIS), as part of its overall vibration isolation strategy. A schematic diagram of a typical ARIS payload rack is shown. The ARIS isolation control system senses rack acceleration via three triaxial accelerometer heads and uses eight pushrod actuators to perform active vibration attenuation. Position sensors housed in the actuator assembly are used to sense the relative position between the rack and the station. Electrical power, data and other essential resources are routed through a set of umbilicals that interface with a passthrough panel at the bottom of the rack. A representative umbilical set is shown.

Fialho, Ian J.↗

Total systems design analysis of high performance structures

Designer-control parameters were identified at interdiscipline interfaces to optimize structural systems performance and downstream development and operations with reliability and least life-cycle cost. Interface tasks and iterations are tracked through a matrix of performance disciplines integration versus manufacturing, verification, and operations interactions for a total system design analysis. Performance integration tasks include shapes, sizes, environments, and materials. Integrity integrating tasks are reliability and recurring structural costs. Significant interface designer control parameters were noted as shapes, dimensions, probability range factors, and cost. Structural failure concept is presented, and first-order reliability and deterministic methods, benefits, and limitations are discussed. A deterministic reliability technique combining benefits of both is proposed for static structures which is also timely and economically verifiable. Though launch vehicle environments were primarily considered, the system design process is applicable to any surface system using its own unique filed environments.

Verderaime, V.↗

Research study on stabilization and control: Modern sampled-data control theory. Design of the large space telescope system

Conditions of self-sustained oscillations in a two-axis model of the nonlinear LST system are studied. The describing function of the CMG frictional nonlinearity of the LST system is used for the analysis, as well as continuous-data and discrete-data models of the simplified LST control system. A numerical-iterative method is described for the analysis of the two-axis system. Approximation methods and the direct plotting of the stability equation are implemented in the study. It is shown that although the dynamics of the two axes are identical, the amplitudes of self-sustained oscillations in the two axes may in principle be different. Analysis shows that the LST systems are of equal amplitudes but with 180-degree phase shift.

Kuo, B. C.↗

Robust stability of second-order systems

This report presents a robust control design using strictly positive realness for second-order dynamic systems. The robust strictly positive real controller allows the system to be stabilized with only acceleration measurements. An important property of this design is that stabilization of the system is independent of the system parameters. The control design connects a virtual system to the given plant. The combined system is positive real regardless of system parameter uncertainty. Then any strictly positive real controllers can be used to achieve robust stability. A spring-mass system example and its computer simulations are presented to demonstrate this controller design.

Chuang, C. H.↗

A robust controller for second-order systems using acceleration measurements

This paper presents a robust control design using strictly positive realness for second-order dynamic systems. The robust strictly positive real controller allows the system to be stabilized with only acceleration measurements. An important property of this design is that stabilization of the system is independent of the system parameters. The control design connects a virtual system to the given plant. The combined system is positive real regardless of system parameter uncertainty. Then any strictly positive real controllers can be used to achieve robust stability. A spring-mass system example and its computer simulations are presented to demonstrate this controller design. Robust performance property of this design is also demonstrated in a simple example.

Chuang, C.-H.↗

G-LIMIT

Dynamic modeling and controller design efforts were conducted at the University of Alabama in Huntsville (UAH) on the Glovebox Integrated Microgravity Isolation Technology (g-LIMIT), under NAG8-1598; the funded period of performance was 8/26/98 through 12/31/00. The title of the grant was 'Support of g-LIMIT for Isolation of Space Science Experiments: Dynamic Modeling and Optimal Controller Synthesis.' Design codes were developed for implementation of a steady-state H infinity controller design method using the frequency weighted plant for the MDOF g-LIMIT design case.

Hampton, R. David↗

Connections between conventional and singular-value-based multi-variable flight control system design techniques

It is proposed that frequency-domain multivariable robustness techniques, when combined with classical multivariable procedures, can offer an additional means of evaluating FCS designs. A lateral-directional FCS for an advanced fighter is used as an example. Robustness to unstructured aircraft-input uncertainties is assessed using purely numerical singular-value procedures. Literal approximations for the singular values of the open-loop plant and controller and for the inverse return difference are shown to provide a means of decomposing and diagnosing robustness problems that are insoluble via purely numerical methods.

Mcruer, D. T.↗

Safe Tracking Control of an Uncertain Euler-Lagrange System with Full-State Constraints using Barrier Functions

This paper presents a novel, safe tracking control design method that learns the parameters of an uncertain Euler-Lagrange (EL) system online using adaptive learning laws. A barrier function (BF) is first used to transform the full-state constrained EL-dynamics into an equivalent unconstrained dynamics. An adaptive tracking controller is then developed along with the parameter update law in the transformed state space such that the states remain bounded for all time within a prescribed bound. A stability analysis is developed that considers the EL-dynamics’ uncertainty, yielding a semi-globally uniformly ultimately bounded (SGUUB) tracking error and the parameter estimation error. The controller design is validated in simulations using a two-link planar manipulator. The results show the proposed method’s ability to track the reference trajectory while remaining inside each of the predefined state bounds.

Robots↗

Open-Loop Control Co-Design of Semisubmersible Floating Offshore Wind Turbines Using Linear Parameter-Varying Models

Here, this paper discusses a framework to design elements of the plant and control systems for floating offshore wind turbines in an integrated manner using linear parameter-varying models. Multiple linearized models derived from aero-elastic simulation software in different operating regions characterized by the incoming wind speed are combined to construct an approximate low-fidelity model of the system. The combined model is then used to generate open-loop, optimal control trajectories as part of a nested control co-design strategy that explores the system’s power production and stability using the platform pitch tilt as a proxy in the context of crucial plant and control design decisions. The radial distance between the central and outer columns and the diameter of the outer columns of the semisubmersible platform are the plant design variables. The platform stability and power production are studied for different plant design decisions. The effect of plant decisions on subsequent power production and stability response of the floating wind turbine is quantified in terms of the levelized cost of energy. The results show that the inner-loop constraints and the plant design decisions affect the turbine’s power and, subsequently, the cost of the system.

17 WIND ENERGY↗

DSN 70-meter antenna X- and S-band calibration. Part 2: System noise temperature measurements and telecommunications link evaluation

The X- and S-band system operating noise temperatures of the Deep Space Network (DSN) 70-m antennas are presented. Models of atmosphere and ground noise temperature contributions, as they affect the antenna calibrations, are given for future use in telecommunications link modeling. The measured 70-m antenna network gain/system noise temperature (G/T) performance is presented. Compared with the earlier 64-m antenna network, G/T improvements of from 1.8 dB to 2.5 dB, depending on elevation angle, were achieved. G/T comparisons are made with the DSN/Flight Project Design Handbook and the Voyager telecommunications design control table. Actual Voyager telecommunications link performance is compared with predictions made by TPAP (the Voyager telecommunications prediction and analysis program) and with measured performance of the individual 70-m antennas. A modification in the use of antenna gain, system noise temperature, and atmospheric attenuation in existing telecommunications design control tables is suggested.

Slobin, S. D.↗

Status report and preliminary results of the spacecraft control laboratory experiment

The Spacecraft Control Laboratory Experiment (SCOLE) was conceived to provide a physical test bed for investigation of control techniques for large flexible spacecraft. The SCOLE problem is defined as two design challenges. The first challenge is to design control laws for a mathematical model of a large antenna attached to the space shuttle by a long flexible mast. The second challenge is to design and implement a control scheme on a laboratory representation of the structure modelled in the first part. Control sensors and actuators are typical of those which the control designer would have to deal with on an actual spacecraft. The primary control processing computer is representative of the capacity and speed which may be expected in actual flight computers. A brief description is given of the laboratory apparatus along with some preliminary results of structural dynamics tests and actuator effectiveness tests.

Williams, Jeffrey P.↗

A dual-mode generalized likelihood ratio approach to self-reorganizing digital flight control system design

Analytic techniques have been developed for detecting and identifying abrupt changes in dynamic systems. The GLR technique monitors the output of the Kalman filter and searches for the time that the failure occured, thus allowing it to be sensitive to new data and consequently increasing the chances for fast system recovery following detection of a failure. All failure detections are based on functional redundancy. Performance tests of the F-8 aircraft flight control system and computerized modelling of the technique are presented.

Source record↗

Data-driven modeling and control of dynamical systems using Koopman and Perron-Frobenius operators

This dissertation studies the data-driven modeling and control problem of nonlinear systems by exploiting the linear operator theoretic framework involving Koopman and Perro-Frobenius operator. A systematic linear-operator based controller design procedure has been established, which can be used to solve a variety of nonlinear control problems, including feedback stabilization using control Lyapunov functions, optimal quadratic regulation using Koopman eigenfunctions and convex optimization formulation of optimal control problem using P-F and Koopman operator approximation. As the core of data-driven modeling, we first propose a new algorithm for the finite-dimensional approximation of the linear transfer Koopman and Perron-Frobenius operator from time-series data. We argue that the existing approach for the finite-dimensional approximation of these transfer operators such as Dynamic Mode Decomposition (DMD) and Extended Dynamic Mode Decomposition (EDMD) do not capture two important properties of these operators, namely positivity and Markov property. The algorithm we propose preserves these two properties. We call the proposed algorithm as naturally structured DMD (NSDMD) since it retains the inherent properties of these operators. Naturally structured DMD algorithm leads to a better approximation of the steady-state dynamics of the system regarding computing Koopman and Perron- Frobenius operator eigenfunctions and eigenvalues. However, preserving positivity property is critical for capturing the real transient dynamics of the system. This positivity property of the transfer operators and it's finite-dimensional approximation play an important role for controller and estimator design of nonlinear systems. To solve the feedback stabilization problem for nonlinear control systems, we tried to take advantage of the Koopman operator framework. The Koopman operator approach provides a linear representation for a nonlinear dynamical system and a bilinear representation for a nonlinear control system. The problem of feedback stabilization of a nonlinear control system is then transformed to the stabilization of a bilinear control system. We propose a control Lyapunov function (CLF)-based approach for the design of stabilizing feedback controllers for the bilinear system. The search for finding a CLF for the bilinear control system is formulated as a convex optimization problem. This leads to a schematic procedure for designing CLF-based stabilizing feedback controllers for the bilinear system and hence the original nonlinear system. Another advantage of the proposed controller design approach outlined in this dissertation is that it does not require explicit knowledge of system dynamics. In particular, the bilinear representation of a nonlinear control system in the Koopman eigenfunction space can be obtained from time-series data. Next, we study the optimal quadratic regulation problem for nonlinear systems. The linear operator theoretic framework involving the Koopman operator is used to lift the dynamics of nonlinear control system to an infinite-dimensional bilinear system. The optimal quadratic regulation problem for nonlinear system is formulated in terms of the finite-dimensional approximation of the bilinear system. A convex optimization-based approach is proposed for solving the quadratic regulator problem for bilinear system. We applied a variety of examples and compared the simulation results between our framework and conventional LQR control using linearized model. For more general optimal control problems, we provide a density-function based convex formulation for the optimal control problem of the nonlinear system. The convex formulation relies on the duality result in the stability theory of a dynamical system involving density function and Perron-Frobenius operator. The optimal control problem is formulated as an infinite-dimensional convex optimization program. The finite-dimensional approximation of the optimization problem relies on the recent advances made in the data-driven computation of the Koopman operator, which is dual to the Perron-Frobenius operator. Simulation results are presented to demonstrate the application of the developed framework.

Huang, Bowen↗

Application of modern control theory to the design of optimum aircraft controllers

The synthesis procedure presented is based on the solution of the output regulator problem of linear optimal control theory for time-invariant systems. By this technique, solution of the matrix Riccati equation leads to a constant linear feedback control law for an output regulator which will maintain a plant in a particular equilibrium condition in the presence of impulse disturbances. Two simple algorithms are presented that can be used in an automatic synthesis procedure for the design of maneuverable output regulators requiring only selected state variables for feedback. The first algorithm is for the construction of optimal feedforward control laws that can be superimposed upon a Kalman output regulator and that will drive the output of a plant to a desired constant value on command. The second algorithm is for the construction of optimal Luenberger observers that can be used to obtain feedback control laws for the output regulator requiring measurement of only part of the state vector. This algorithm constructs observers which have minimum response time under the constraint that the magnitude of the gains in the observer filter be less than some arbitrary limit.

Power, L. J.↗

Learning control for slewing of a flexible panel

This paper studies the applicability of a discrete-time learning control method to the slewing control of a large flexible panel. Among the issues discussed are feasibility of the desired trajectories and their specification schemes, learning control by linear feedback, limitation of the actuator device output, and robustness to parameter changes or modeling errors associated with the chosen learning control design. To demonstrate the effectiveness of learning control, the system is designed with a proportional controller of the base angle only. Then application of the learning control is shown to make the system learn quickly to achieve the desired slewing without residual vibration at the end of the maneuver. Simulation results are reported and discussed.

Phan, M.↗