Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Composition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57

Research on the interfacial structure and property improvement of the Cfiber/2Si-B-3C-N ceramic matrix composite

Highlights: • The C{sub fiber}/2Si-B-3C-N composite with nice properties was successfully prepared. • ZrO{sub 2} promotes the densification process, homogeneous nucleation and grain growth. • The interface reaction in the composite was well controlled by the addition of ZrO{sub 2}. • The damage to carbon fiber was largely avoided by the addition of ZrO{sub 2}. - Abstract: A mixture of the mechanically alloyed 2Si-B-3C-N powder and short carbon fiber was hot pressed at 1800 °C for 30 mins in nitrogen. Careful investigation to the prepared C{sub fiber}/2Si-B-3C-N ceramic matrix composite revealed that the composite was very difficult to be densified. Heterogeneous nucleation, abnormal grain growth and severe interface reaction occurred on the fiber surface or between the fiber and the ceramic matrix, leading to a small density and weak mechanical properties of the composite. For the prepared composite without any additive, the relative density, flexural strength, elastic modulus and fracture toughness is 71.7%, 64.6 MPa, 14.7 GPa and 1.47 MPa·m{sup 1/2}, respectively. The average size of the SiC grains close to and far away from the carbon fiber is 249.10 nm and 50.45 nm, respectively. However, with the addition of ZrO{sub 2} (7.5 mol%), the above mentioned phenomenons are changed noticeably, and those properties are significantly increased to 88.5%, 112.4 MPa, 111.1 GPa and 2.94 MPa·m{sup 1/2}, respectively. At the same time, the SiC grains close to or far away from the carbon fiber almost have the same average size of about 448.21 nm, and almost no interface reaction occurs. It shows that the addition of ZrO{sub 2} not only facilitates the sintering and densification process, but also depresses the interface reaction, promotes the homogeneous nucleation and grain growth, and hence significantly improves the mechanical properties of the C{sub fiber}/2Si-B-3C-N composite. This interesting finding is favorable for the preparation of carbon fiber reinforced ceramic matrix composite, which requires both a large relative density and well controlled interface reaction.

36 MATERIALS SCIENCE↗

Synthesis, structure and electrochemical properties of polyaniline/MoO{sub 3} nanobelt composite for lithium battery

Graphical abstract: Hydrothermal method was introduced for the synthesis of MoO{sub 3} nanobelts and polyaniline (PANI)/MoO{sub 3} nanobelt composites. The structure and morphology of the samples were studied by X-ray diffraction (XRD), Fourier transform infrared radiation (FTIR), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analysis. We can see the presence of polyaniline on the MoO{sub 3} nanobelts surface in the TEM pictures as shown in Fig. (a). The pure MoO{sub 3} nanobelts exhibit the initial specific capacity 276 mAhg{sup −1}, whereas PANI/MoO{sub 3} nanobelt composite shows little low initially 228 mAhg{sup −1} after that it has more stabilized specific capacity with increasing cycle numbers as shown in Fig. (b). The cyclic voltammograms of the PANI/MoO{sub 3} nanobelt composite show better cyclic performance compared to pure MoO{sub 3} nanobelts. The electrochemical impedance spectres were studied for both the pure and PANI/MoO{sub 3} samples at 2.0 and 3.5 potentials. The role of the PANI polymeric component of the composite material seems to be the stabilization of the specific capacity due to probable homogeneous distribution of the induced stress during cycling. Display Omitted Highlights: ► Hydrothermal synthesis of MoO{sub 3}, PANI/MoO{sub 3} nanobelts. ► Samples were characterised by XRD, FTIR, DSC, SEM, TEM, CV and impedance. ► MoO{sub 3} nanobelts cathode battery shows initial specific capacity 276 mAhg{sup −1}. ► PANI/MoO{sub 3} nanobelts show initial specific capacity 228 mAhg{sup −1} but high stability. ► PANI/MoO{sub 3} sample studies by impedance at the potentials of 2.0 and 3.5 V. -- Abstract: The MoO{sub 3} nanobelts and polyaniline (PANI)/MoO{sub 3} nanobelt composite were synthesized using hydrothermal method. The crystal structure and morphology of the samples were studied by X-ray diffraction (XRD), Fourier transform infrared radiation (FTIR), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Differential scanning calorimetric (DSC) and thermo gravimetric (TG) measurements were carried out for PANI/MoO{sub 3} nanobelt composite. The pure MoO{sub 3} nanobelts exhibit the initial specific capacity 276 mAhg{sup −1}, whereas PANI/MoO{sub 3} nanobelt composite showed little low initially 228 mAhg{sup −1} after that it has more stabilized specific capacity with increasing cycle numbers at constant current density of 30.7 mAg{sup −1} in the potential range 1.0–4.0 V vs. Li/Li{sup +}. The electrochemical impedance profiles were also studied. The cyclic voltammograms of the PANI/MoO{sub 3} nanobelt composite showed better cyclic performance as compared with pure MoO{sub 3} nanobelts, this is due to the role of PANI polymeric component stabilization of the specific capacity by homogeneous distribution within nanobelts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

One-step synthesis of homogeneous BaFe{sub 12}O{sub 19}/Y{sub 3}Fe{sub 5}O{sub 12} composite powders

Highlights: • A simple one-step sol–gel method was used to synthesize composite magnets. • The composite powders show good homogeneity and exchange coupling. • The M{sub r}/M{sub s} value increases with the BaM concentration. - Abstract: BaFe{sub 12}O{sub 19}/Y{sub 3}Fe{sub 5}O{sub 12} (BaM/YIG) composite powders were synthesized via a simple one-step sol–gel method. The phase composition and morphology of the as-synthesized composite powders were characterized using an X-ray diffractometer and a scanning electron microscopy equipped with energy dispersive X-ray spectroscopy. The magnetic properties of the composite powders were investigated by a vibrating sample magnetometer. Compared with the composite powders prepared by the conventional physical mixing method, the BaM/YIG composite powders show better homogeneity and exchange coupling.

36 MATERIALS SCIENCE↗

Dielectric and magnetic properties of xCoFe{sub 2}O{sub 4}–(1 − x)[0.5Ba(Zr{sub 0.2}Ti{sub 0.8})O{sub 3}–0.5(Ba{sub 0.7}Ca{sub 0.3})TiO{sub 3}] composites

Highlights: • Spinel–perovskite xCoFe{sub 2}O{sub 4}–(1 − x)(0.5Ba(Zr{sub 0.2}Ti{sub 0.8})O{sub 3}–0.5(Ba{sub 0.7}Ca{sub 0.3})TiO{sub 3}) composites have been synthesized by solid state reaction method. • Two anomalies in dielectric constant have been identified, and the composites show relaxor behaviour. • The magnetic properties of the composites improve with increasing concentration of CoFe{sub 2}O{sub 4}. • Enhanced magnetodielectric effect is found, and magnetoelectric coupling has been confirmed by Δϵ ∼ γM{sup 2} relation. • Optical band gap energy of these composites has been reported for the first time. - Abstract: xCoFe{sub 2}O{sub 4}–(1 − x)(0.5Ba(Zr{sub 0.2}Ti{sub 0.8})O{sub 3}–0.5(Ba{sub 0.7}Ca{sub 0.3})TiO{sub 3}) composites with x = 0.1, 0.2, 0.3 and 0.4 have been synthesized by solid state reaction method. X-ray diffraction analysis and field emission secondary electron microscopy have been used for structural and morphological analysis, respectively. The spinel CoFe{sub 2}O{sub 4} and perovskite 0.5Ba(Zr{sub 0.2}Ti{sub 0.8})O{sub 3}–0.5(Ba{sub 0.7}Ca{sub 0.3})TiO{sub 3} phase could be identified in the composites. Two anomalies in dielectric constant have been identified: first one is close to ferroelectric to paraelectric phase transition of 0.5Ba(Zr{sub 0.2}Ti{sub 0.8})O{sub 3}–0.5(Ba{sub 0.7}Ca{sub 0.3})TiO{sub 3} ceramic and the other lies near the magnetic transition temperature of CoFe{sub 2}O{sub 4}. There is an increase in magnetocapacitance and saturation magnetization of the composites at room temperature with increase in CoFe{sub 2}O{sub 4} content. The magnetoelectric coupling coefficient (γ) was approximated by Δϵ ∼ γM{sup 2} relation. The optical band gap energy of the composites decreases with increase in CoFe{sub 2}O{sub 4} content.

36 MATERIALS SCIENCE↗

Synthesis, characterization, electrical and dielectric studies of AgCuI and Co-SnO{sub 2} composite solid electrolytes

Highlights: • The SCI–CDS composites were characterized by XRD, Far IR and SEM. • Conductivity reached 1.29 × 10{sup −4} S/cm at room temperature for x = 0.4 composition. • The value of dielectric constant decreases with the increase of frequency. - Abstract: The composite solid electrolytes of AgCuI (SCI) and Co-SnO{sub 2} (CDS) were prepared by direct mixing method. The phase structure, composition and surface morphology of the composites were explained by X-ray diffraction (XRD), Far infrared spectroscopy (Far IR) and Scanning electron microscopy (SEM). AC impedance spectroscopy revealed that the ionic conductivity was effectively increased with the increase of temperature. Presence of a semicircle in the impedance spectra shows the greater contribution of grain than the grain boundary. Addition of CDS particles enhanced the ionic conductivity of the composites, reached a maximum value σ = 1.29 × 10{sup −4} S cm{sup −1} at room temperature for x = 0.4 composition. The dielectric values of the composite were gradually increased upon increasing the temperature, followed by a sharp change observed at 440 K. The electrical modulus of the sample was decreased with the increase of temperature and exhibits a single relaxation.

36 MATERIALS SCIENCE↗

ZnS/Ni{sub 2}P core/shell composites: Simple hydrothermal synthesis, characterization and its photocatalytic degradation of pyronine B

Highlights: • ZnS/Ni{sub 2}P composites have been firstly synthesized via a gentle hydrothermal route. • The composites have been characterized by XRD, SEM and TEM. • ZnS/Ni{sub 2}P showed enhanced photocatalytic degradation activity for pyronine B. • The reason for the enhanced photocatalytic activity has been discussed. - Abstract: ZnS/Ni{sub 2}P core/shell composites were successfully synthesized using a hydrothermal method. The composites have been characterized by XRD, SEM, TEM and the corresponding results showed that the composites were composed of the cubic ZnS microspheres, which were made up of ZnS nanoparticles, and Ni{sub 2}P nanoparticles coated on the surfaces of ZnS microspheres. Compared with ZnS microspheres, ZnS/Ni{sub 2}P core/shell composites showed enhanced photocatalytic degradation activity for pyronine B under UV irradiation. This may be related to the effective separation of photogenerated electron–hole pairs in ZnS/Ni{sub 2}P composites which can greatly reduce the chance of their recombination. Furthermore, superoxide ions and hydroxyl radical can be more easily produced through ZnS/Ni{sub 2}P composites, which is also beneficial for the degradation of pyronine B.

36 MATERIALS SCIENCE↗

Synthesis and electrochemical performance of mesoporous SiO{sub 2}–carbon nanofibers composite as anode materials for lithium secondary batteries

Highlights: • Mesoporous SiO{sub 2}–carbon nanofibers composite synthesized on Ni foam without any binder. • This composite was directly applied as anode material of Li secondary batteries. • Showed the highest initial (2420 mAh/g) and discharging (2092 mAh/g) capacity. • This material achieved a retention rate of 86.4% after 30 cycles. - Abstract: In this study, carbon nanofibers (CNFs) and mesoporous SiO{sub 2}–carbon nanofibers composite were synthesized and applied as the anode materials in lithium secondary batteries. CNFs and mesoporous SiO{sub 2}–CNFs composite were grown via chemical vapor deposition method with iron-copper catalysts. Mesoporous SiO{sub 2} materials were prepared by sol–gel method using tetraethylorthosilicate as the silica source and cetyltrimethylammoniumchloride as the template. Ethylene was used as the carbon source and passes into a quartz reactor of a tube furnace heated to 600 °C, and the temperature was maintained at 600 °C for 10 min to synthesize CNFs and mesoporous SiO{sub 2}–CNFs composite. The electrochemical characteristics of the as-prepared CNFs and mesoporous SiO{sub 2}–CNFs composite as the anode of lithium secondary batteries were investigated using a three-electrode cell. In particular, the mesoporous SiO{sub 2}–CNFs composites synthesized without binder after depositing mesoporous SiO{sub 2} on Ni foam showed the highest charging and discharging capacity and retention rate. The initial capacity (2420 mAh/g) of mesoporous SiO{sub 2}–CNFs composites decreased to 2092 mAh/g after 30 cycles at a retention rate of 86.4%.

36 MATERIALS SCIENCE↗

Preparation and characterization of CdS/BiOI composites with enhanced photocatalytic activity for degradation of 17α-ethinyl estradiol

Highlights: • A chemical bath deposition method was used for synthesis of CdS/BiOI composite. • The removal rate of EE2 over CdS/BiOI composite could approach 100% after 12 min under visible light irradiation. • The Z-scheme mechanism of EE2 degradation by CdS/BiOI was proposed. - Abstract: A novel CdS/BiOI composite has been prepared via a chemical bath deposition method. The physical and chemical properties of as-prepared composites were characterized by XRD, SEM, TEM, EDS, XPS, UV–vis DRS, and PL. The synthesized CdS/BiOI composites exhibited superior photocatalytic activity in photodegrading of 17α-ethinyl estradiol (EE2) compared to pure CdS and pure BiOI, and the removal rate of EE2 could approach 100% after only 12 min of visible light irradiation using 3:1 CdS/BiOI composite as photocatalyst. The reaction rate constant over 3:1 CdS/BiOI composite was 6.3, 7.1 and 70.9 times higher than that of pure CdS, pure BiOI and P25 respectively. In addition, a Z-scheme charge separation mechanism was proposed on the basis of the experimental results and the theoretical calculation. Moreover, the prepared composite showed good stability and recyclability which are beneficial for its practical application.

36 MATERIALS SCIENCE↗

Low loss polypropylene-silicon composites for millimetre wave applications

Highlights: • Developed polypropylene-silicon composite. • The composite shows a decrease in loss tangent with increasing frequency. • The composite is useful for high frequency applications such as Internet of Things and 5th Generation wireless communication. - Abstract: Polypropylene-silicon composite laminates were fabricated via hot pressing and their dielectric properties up to 35 GHz were studied. The loss tangent was found to decrease with increasing frequency whereas an increasing trend of loss tangent has previously been reported in the literature for such composites. The decreasing trend of the loss tangent with frequency is due to the decreasing conductor loss of silicon (Si) and indicates the possibility for use in high frequency applications such as the Internet Of Things and 5 t h generation wireless communication. The composite containing 25 vol% of Si had a relative permittivity of 3.5 and a loss tangent of 0.001 at 35 GHz. The coefficient of thermal expansion and the thermal conductivity of 40 vol% Si loaded composites were 51 ppm/{sup o}C and 2.23 W/mK, respectively. The thermal conductivity of the composite increased by 163% and 913% for 25 and 40 vol% Si addition, respectively.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Fabrication of Piezoelectric Polymer and Metal–Organic Framework Composite Thin Films Using Solution Shearing

Polymer-metal–organic framework (polymer-MOF) composites have garnered significant interest as polymers can enhance the processability and industrial applicability of MOFs. Thin films of these composites are particularly attractive for applications in sensing, separations, and flexible electronics. Solution shearing, a meniscus-guided coating technique, has emerged as a scalable process for fabricating thin films of MOFs, and can produce large-area films within minutes. In this study, we utilized solution shearing to fabricate composite thin films of a MOF UiO-66 and a piezoelectric polymer poly(vinylidene fluoride-trifluoroethylene) (P(VDF-TrFE)), investigating how polymer concentration during MOF synthesis and composite formation influences thin film properties, including crystallinity, surface coverage, and piezoelectric performance. Additionally, solid-state NMR spectroscopy was utilized to probe the interactions between P(VDF-TrFE) and UiO-66 in the composite. Evidence from solid-state NMR indicated polymer-MOF interactions, suggesting that the polymer strands are in close proximity to the UiO-66 pores, supporting a mixed surface coating and pore infiltration model. Furthermore, incorporating P(VDF-TrFE) enhanced the film’s areal coverage from 70% to 100%. While the thermal conductivity remained essentially unchanged, the composite film showed an improved piezoelectric effect. The composite with 91 wt % P(VDF-TrFE) exhibited the highest output voltage of 9.1 V and a sensitivity of 0.26 V/N under applied pressure. This work demonstrates the potential of solution shearing as a scalable technique for fabricating polymer-MOF composite thin films.

P(VDF-TrFE)↗

Polymer-Grafted Cellulose Nanofibrils with Enhanced Interfacial Compatibility for Stronger Poly(lactic acid) Composites

Cellulose nanofibrils (CNFs) are a promising reinforcement for biodegradable composite matrices such as poly(lactic acid) (PLA), but they require commercially scalable drying methods that preserve their fibrillar morphology along with improved interfacial interactions with polymer matrices. In this work, a water-based grafting-through polymerization scheme to modify CNFs improved spray drying behavior and reinforcement capacity in PLA composites. All polymer modifications yielded CNFs with a more fibrillar morphology after spray drying, increasing specific surface area by up to 490% compared to unmodified CNFs, values similar to conventional freeze drying. Polymer-grafted CNFs in PLA composites improved the tensile strength by 16% at 20 wt % loading and stiffness by 22% at a 10 wt % loading with two different graft-polymer chemistries compared to unmodified CNF composites. Surface energy heterogeneity measurements of the reinforcements and PLA matrix were employed to understand the improvements in composite properties. Polymer modifications lowered the total surface energy of the CNFs, and calculated ratios of work of adhesion to work of cohesion suggested improved interfacial compatibility for four of the modified CNFs with PLA. Rheological oscillatory shear studies of the composites correlated solid-like melt behavior, as demonstrated by storage moduli dominance, with higher tensile strength. Thermal analysis of the composites revealed that excessive plasticization by the poly(oligoethylene glycol methyl ether methacrylate)-grafted sample potentially offset mechanical property improvements imparted by the more fibrillar morphology. This work provides an opportunity for large-scale manufacturing of CNF/PLA composites via an entirely aqueous modification scheme and industrially relevant spray drying process.

36 MATERIALS SCIENCE↗

Additive manufacturing of carbon fiber-reinforced thermoset composites via in-situ thermal curing

Fiber-reinforced polymer composites are lightweight structural materials widely used in the transportation and energy industries. Current approaches for the manufacture of composites require expensive tooling and long, energy-intensive processing, resulting in a high cost of manufacturing, limited design complexity, and low fabrication rates. Here, we report rapid, scalable, and energy-efficient additive manufacturing of fiber-reinforced thermoset composites, while eliminating the need for tooling or molds. Use of a thermoresponsive thermoset resin as the matrix of composites and localized, remote heating of carbon fiber reinforcements via photothermal conversion enables rapid, in-situ curing of composites without further post-processing. Rapid curing and phase transformation of the matrix thermoset, from a liquid or viscous resin to a rigid polymer, immediately upon deposition by a robotic platform, allows for the high-fidelity, freeform manufacturing of discontinuous and continuous fiber-reinforced composites without using sacrificial support materials. This method is applicable to a variety of industries and will enable rapid and scalable manufacture of composite parts and tooling as well as on-demand repair of composite structures.

36 MATERIALS SCIENCE↗

Damping mechanisms in alumina borate whisker-reinforced-aluminum matrix composites with or without SnO{sub 2} coatings

SnO{sub 2} was successfully coated on the surface of alumina borate whiskers. The pure aluminum matrix composites reinforced with a SnO{sub 2}-coated alumina borate whisker were fabricated by squeeze casting. The effects of coating contents on the damping properties of the coated composites at various temperatures, frequencies, and strain amplitudes were examined. The microstructures of the coated composites were also investigated through transmission electron microscopy observations. These results indicate that the introduction of Sn at the interface between whisker and matrix in the coated composites during the squeeze casting process alters not only the interface structures but also the dislocation status of the matrices in the vicinity of the interface. The results of damping characterization indicate that the damping capacities of the coated composites strongly depend on the coating contents and strain amplitudes. A damping peak at low temperatures appeared not only in the coated composites but also in the noncoated one, which is related to dislocation motion and interfacial slip caused by Sn. A damping peak at high temperatures appeared only in the coated composites, and the damping mechanisms at high temperature change with the increase in strain amplitudes. Sn played an important role on the damping mechanisms of the coated composites all along.

36 MATERIALS SCIENCE↗

Development of silver and zinc oxide decorated nanoclay containing polymeric composites for water disinfection applications

Contaminated drinking water has serious implications to the human health that could lead to death. The rapid growth of bacterial contamination in drinking water is alarming, and yet a robust and cost effective method with less limitation has not been developed. The current study is aimed at evaluating the performance of nanoclay composites dispersed in chitosan biopolymer as an antibacterial material. The performances of the composites were evaluated using the batch kinetic studies. Three composites of Ag-CtsB, ZnO-CtsB and Ag/ZnO-CtsB were prepared and evaluated against gram negative Escherichia coli and gram positive Enterococcus faecalis bacteria. The composites were characterized by powder X-ray diffraction, scanning electron microscope, energy dispersive spectroscopy and BET surface area measurements. Antibacterial activity results showed that the composites can be a potent bactericide material for water disinfection as they are highly effective against both gram negative and gram positive bacteria tested. Whereas both Ag-CtsB and ZnO-CtsB composites showed good antibacterial activity against bacteria with removal efficiency from 51%, best antibacterial activity was observed with Ag/ZnO-CtsB composite with removal efficiency from 78%. The results revealed that Ag/ZnO-CtsB composite is a promising bactericide that is highly effective against both gram negative and gram positive bacteria tested.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Properties of natural rubber/attapulgite composites prepared by latex compounding method: Effect of filler loading

This paper reports on the effect of filler loading on properties of natural rubber (NR)/attapulgite (ATP) composites. The NR/ATP composites were prepared by latex compounding method. It is called as masterbatch. The masterbatch was subsequently added to the NR through melt mixing process. The vulcanized NR/ATP composites were subjected to mechanical, swelling and morphological tests. All the results were compared with NR/ATP composites prepared by conventional system. The composites from masterbatch method showed better results compared to composites prepared by conventional method. They have higher tensile properties, elongation at break and tear strength. The images captured through scanning electron microscopy test revealed the improvement of tensile strength in masterbatch NR/ATP composites. It can be seen clearly that masterbatch NR/ATP have better filler dispersion compared to conventional method NR/ATP composites.

36 MATERIALS SCIENCE↗

Site Disorder as a Predictor for Compositionally Complex 5RE 2 Zr 2 O 7 Ceramic Phase Stability

Here, phase formation and stability of five component compositionally complex rare earth zirconates (5RE 2 Zr 2 O 7 ) were investigated by X-ray diffraction and electron microprobe analysis. Zirconates with different rare earth compositions (LaNdSmEuDy, LaNdSmEuYb, LaNdEuErYb, LaNdDyErYb, SmEuDyYHo, LaYHoErYb, and DyYHoErYb) were synthesized at 1700°C and 2000°C by the solid-state method to investigate the effect of A-site site disorder (δ A ) on phase stability. Increased site disorder results from mixed cation occupancy with localized crystallographic strain and bond disorder. Compositions LaNdSmEuDy (δ A = 4.6) and LaNdSmEuYb (δ A = 6.0) produced a single pyrochlore phase and compositions SmDyYHoErYb (δ A = 2.8), LaYHoErYb (δ A = 6.2), and DyYHoErYb (δ A = 1.7) produced a single fluorite phase. High δ A compositions LaNdEuErYb (δ A = 6.9) and LaNdDyErYb (δ A = 7.2) produced a pyrochlore and fluorite phase mixture at 1700°C. Single phase was obtained for the latter composition at 2000°C. Of the single phase compositions calcined at 1700°C, LaNdSmEuYb and LaYHoErYb (both with largest δ A ) showed decomposition to mixed fluorite and pyrochlore phases during lower temperature anneals, indicating entropic stabilization. Comparison with prior work shows a temperature dependence of the critical δ A for phase stability, and compositions near it are expected to be entropy stabilized.

36 MATERIALS SCIENCE↗

IMPACTS OF SMALL COLUMN ION EXCHANGE STREAMS ON DWPF GLASS FORMULATION KT07-SERIES GLASS COMPOSITIONS

This report is the third in a series of studies of the impacts of the addition of Crystalline Silicotitanate (CST) and Monosodium Titanate (MST) from the Small Column Ion Exchange (SCIX) process on the Defense Waste Processing Facility (DWPF) glass waste form and the applicability of the DWPF process control models. MST from the Salt Waste Processing Facility is also considered in the study. The KT07-series glasses were selected to evaluate any potential impacts of noble metals on their properties and performance. The glasses characterized thus far for the SCIX study have not included noble metals since they are not typically tracked in sludge batch composition projections. However, noble metals can act as nucleation sites in glass melts, leading to enhanced crystallization. This crystallization can potentially influence the properties and performance of the glass, such as chemical durability, viscosity, and liquidus temperature. The noble metals Ag, Pd, Rh, and Ru were added to the KT07-series glasses in concentrations based on recent measurements of Sludge Batch 6, which was considered to contain a high concentration of noble metals. The KT04-series glasses were used as the baseline compositions. After fabrication, the glasses were characterized to determine their homogeneity, chemical composition, durability, and viscosity. Liquidus temperature measurements are also underway but were not complete at the time of this report. The liquidus temperature results for the KT07-series glasses, along with several of the earlier glasses in the SCIX study, will be documented separately. All of the KT07-series glasses, both quenched and slowly cooled, were found to be amorphous by X-ray diffraction. Chemical composition measurements showed that all of the glasses met their targeted compositions. The Product Consistency Test (PCT) results showed that all of the glasses had chemical durabilities that were far better than that of the Environmental Assessment benchmark glass. The measured PCT responses were well predicted by the current DWPF Product Composition Control System (PCCS) durability models. The measured viscosity values for each KT07-series glass were acceptable for DWPF processing and were well predicted by the current PCCS model. Overall, the results show that the inclusion of relatively high concentrations of noble metals (in terms of expected values for a DWPF sludge batch) had no significant impact on the properties and performance of these glass compositions. There were no significant differences in the measured properties when compared to those of the KT04-series glasses, which did not contain noble metals. Liquidus temperature measurements are still underway and there may be an impact of the noble metals on those measurements. However, no adverse effects were noted in terms of crystallization after slow cooling. At the completion of these studies, all of the data generated will be reviewed with regard to the applicability of the DWPF PCCS models and recommendations will be made as to whether the validation ranges of the current models can be extended, or whether some or all of the models need to be refit to allow for the incorporation of the SCIX streams. As changes are made to the projected sludge compositions and the volume of the SCIX material, additional evaluations should be performed.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

TIME-TEMPERATURE-TRANSFORMATION (TTT) DIAGRAMS FOR FUTURE WASTE COMPOSITIONS

As a part of the Waste Acceptance Product Specifications (WAPS) for Vitrified High-Level Waste Forms defined by the Department of Energy - Office of Environmental Management, the waste form stability must be determined for each of the projected high-level waste (HLW) types at the Savannah River Site (SRS). Specifically, WAPS 1.4.1 requires the glass transition temperature (T{sub g}) to be defined and time-temperature-transformation (TTT) diagrams to be developed. The T{sub g} of a glass is an indicator of the approximate temperature where the supercooled liquid converts to a solid on cooling or conversely, where the solid begins to behave as a viscoelastic solid on heating. A TTT diagram identifies the crystalline phases that can form as a function of time and temperature for a given waste type or more specifically, the borosilicate glass waste form. In order to assess durability, the Product Consistency Test (PCT) was used and the durability results compared to the Environmental Assessment (EA) glass. The measurement of glass transition temperature and the development of TTT diagrams have already been performed for the seven Defense Waste Processing Facility (DWPF) projected compositions as defined in the Waste Form Compliance Plan (WCP) and in SRNL-STI-2009-00025. Additional phase transformation information exists for other projected compositions, but overall these compositions did not cover composition regions estimated for future waste processing. To develop TTT diagrams for future waste types, the Savannah River National Laboratory (SRNL) fabricated two caches of glass from reagent grade oxides to simulate glass compositions which would be likely processed with and without Al dissolution. These were used for glass transition temperature measurement and TTT diagram development. The glass transition temperatures of both glasses were measured using differential scanning calorimetry (DSC) and were recorded to be 448 C and 452 C. Using the previous TTT diagrams as guidance, subsamples of each glass were isothermally heat treated for 1 to 768 hours at temperatures between 500 C to 1000 C. Each of the heat treated samples, along with quenched and centerline canister cooled (CCC) treated samples, were analyzed using X-ray diffraction (XRD) and the PCT. Maximum crystallization was detected in samples treated at 700 C and 600 C for more than 96 hours in both glasses. Phases crystallized were similar in composition if not the same as those found in the previous TTT studies. Six different crystalline phases were detected, including nepheline, aegirine, lithium silicate, trevorite (spinel based), krinovite, and calcium magnesium iron silicon oxide. Overall, phases were spinel (iron) based, lithium metasilicate, sodium aluminosilicate or alkali transition metal silicate in composition. No new crystalline families were detected. Durability, as measured by the PCT, decreased when lithium silicate or nepheline crystals were present. The conclusions of this study were consistent with previous studies. In order to continue to meet the requirements of the WCP, a simplified strategy is suggested for the generation of future TTT diagrams. Only extremely significant changes in composition resulting from processing strategy changes would require generating more TTT diagrams.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗