Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Catalyst”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Probing the Active Sites of MoS 2 Based Hydrotreating Catalysts Using Modulation Excitation Spectroscopy

The reactive surface sites of MoS 2 hydrotreating catalysts (unpromoted as well as Co- and Ni-promoted) supported on MgAl 2 O 4 spinel were investigated with respect to the substitution of sulfur by oxygen using in situ XAS coupled with modulation excitation spectroscopy (MES). Specifically, MES experiments were carried out by periodically cycling between a H 2 O and H 2 S containing hydrogen gas mixture at 400 °C. Due to the low fraction of S–O exchange, conventional XANES and EXAFS data hardly showed any changes when these catalysts were exposed to increasing ratios of H 2 O to H 2 S in an H 2 atmosphere. XANES and EXAFS data extracted at the Mo K-edge by MES analysis showed that for approximately 1% of the Mo atoms, sulfur atoms are replaced by oxygen atoms when exposed to H 2 O, causing partial oxidation of these active sites. The reaction is reversible and Mo returns to its initial sulfide phase when H 2 O is removed and H 2 S is supplied in the feed. In the case of Co- and Ni-promoted catalysts, the magnitude of S–O exchange was found to be reduced, indicating the beneficial effect of promotion. MES at the Ni K-edge showed that Ni was oxidized during H 2 O exposure, which in turn delayed the Mo oxidation in the Ni-promoted catalyst. The structures of these catalysts under S–O exchange were modeled using density functional theory (DFT) calculations, showing that the edge atoms are affected strongly. For all three catalysts, OH substitution is more favorable, while O substitution could be possible at high H 2 O pressure for unpromoted MoS 2 . Mo K-edge XANES spectra calculated using these simulated structures support the results obtained from the MES experiments. In conclusion, the presented approach using MES in combination with XAS and supported by DFT can be extended in general to catalysts under operando conditions and is thus a useful tool for determination of the active site on an atomic-scale.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Copper-Based Catalysts Confined in Carbon Nanocage Reactors for Condensed Ester Hydrogenation: Tuning Copper Species by Confined SiO 2 and Methanol Resistance

Hydrogenation of aliphatic esters to natural alcohols is an important strategy for the efficient utilization of biomass-derived oils. The synthesis of highly active copper (Cu)-based catalysts is a challenge for condensed-phase ester hydrogenation due to the difficulties in controlling active sites and catalyst deactivation. In this work, a copper-based catalyst confined in a carbon nanocage reactor was successfully designed and prepared. The copper catalyst with 56 wt % SiO 2 exhibited the best performance because of the optimum proportion of Cu + and Cu 0 sites and high dispersion. The interaction between SiO 2 and Cu particles contributes to the formation of Cu + species, which is the key site for the adsorption of carbonyl groups. Meanwhile, the confinement effect of the carbon nanocages effectively inhibited the agglomeration of the copper particles. The catalysts exhibited not only excellent thermal stability but also superior methanol resistance in comparison with the Cu/SiO 2 catalyst. On the basis of the density functional theory (DFT) calculations results, methanol resistance should be attributed to the fewer hydroxyl groups on the catalyst surface, which increase the activation barrier for the dissociation of silica, allowing the stable holding of the copper species in the methanol solvent.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2014

Poisoning of a Silica-Supported Cobalt Catalyst due to Presence of Sulfur Impurities in Syngas during Fischer–Tropsch Synthesis: Effects of Chelating Agent

The effects of sulfur impurities on the performance of cobalt-based Fischer–Tropsch catalysts are evaluated under industrially relevant operating conditions of temperature, pressure, and impurity levels. Chelating agents (CAs) were used to modify the SiO 2 support, and the performances of the CA-modified catalysts are compared with conventional Co/SiO 2 catalysts. For both the Co/SiO 2 and CA-modified catalysts, the presence of sulfur in the inlet syngas results in a notable drop in the CO conversion, an undesired shift in the hydrocarbon selectivity toward short-chain hydrocarbons, more olefins in the products, and lower product yields. In the post-poisoning stage, i.e., after termination of sulfur introduction in the inlet syngas, the CA-modified catalysts recover activity and selectivity (to some extent at least), whereas such trends are not observed for the base-case, i.e., unmodified Co/SiO 2 catalyst. Finally, the improved performance of the CA-modified catalysts in the presence of sulfur is attributed to higher densities of active sites.

Bambal, Ashish S.↗
DOE OSTI2015

Medium Effects are as Important as Catalyst Design for Selectivity in Electrocatalytic Oxygen Reduction by Iron-porphyrin Complexes

Several substituted iron porphyrin com-plexes were evaluated for oxygen reduction reaction (ORR) electrocatalysis in different homogeneous and heterogeneous media. The selectivity for 4-electron re-duction to H2O vs. 2-electron reduction to H2O2 varies substantially from one medium to another for a given catalyst. In many cases, the influence of the medium in which the catalyst is evaluated has a larger effect on the observed selectivity than the factors attributable to chemical modification of the catalyst. For instance, introduction of potential proton relays has variable effects depending on the catalyst medium. Thus, comparisons of ORR selectivity results need to be interpreted with caution, as the catalysis is a property not just of the catalyst, but also of the larger mesoscale environment be-yond the catalyst. Still, in all the direct pairwise comparisons in the same medium, the catalysts with potential proton relays have similar or better selectivity for the preferred 4e– path. This work was supported as part of the Center for Molecular Electrocatalysis, an Energy Frontier Research Center funded by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences.

Rigsby, Matthew L.↗
DOE OSTI2022

Observation and rationalization of nitrogen oxidation enabled only by coupled plasma and catalyst

Abstract Heterogeneous catalysts coupled with non-thermal plasmas (NTP) are known to achieve reaction yields that exceed the contributions of the individual components. Rationalization of the enhancing potential of catalysts, however, remains challenging because the background contributions from NTP or catalysts are often non-negligible. Here, we first demonstrate platinum (Pt)-catalyzed nitrogen (N 2 ) oxidation in a radio frequency plasma afterglow at conditions at which neither catalyst nor plasma alone produces significant concentrations of nitric oxide (NO). We then develop reactor models based on reduced NTP- and surface-microkinetic mechanisms to identify the features of each that lead to the synergy between NTP and Pt. At experimental conditions, NTP and thermal catalytic NO production are suppressed by radical reactions and high N 2 dissociation barrier, respectively. Pt catalyzes NTP-generated radicals and vibrationally excited molecules to produce NO. The model construction further illustrates that the optimization of productivity and energy efficiency involves tuning of plasma species, catalysts properties, and the reactor configurations to couple plasma and catalysts. These results provide unambiguous evidence of synergism between plasma and catalyst, the origins of that synergy for N 2 oxidation, and a modeling approach to guide material selection and system optimization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

P-block single-metal-site tin/nitrogen-doped carbon fuel cell cathode catalyst for oxygen reduction reaction

This contribution reports the discovery and analysis of a p-block Sn-based catalyst for the electroreduction of molecular oxygen in acidic conditions at fuel cell cathodes; the catalyst is free of platinum-group metals and contains single-metal-atom actives sites coordinated by nitrogen. The prepared SnNC catalysts meet and exceed state-of-the-art FeNC catalysts in terms of intrinsic catalytic turn-over frequency and hydrogen–air fuel cell power density. The SnNC-NH 3 catalysts displayed a 40–50% higher current density than FeNC-NH 3 at cell voltages below 0.7 V. Additional benefits include a highly favourable selectivity for the four-electron reduction pathway and a Fenton-inactive character of Sn. Here, a range of analytical techniques combined with density functional theory calculations indicate that stannic Sn(iv)Nx single-metal sites with moderate oxygen chemisorption properties and low pyridinic N coordination numbers act as catalytically active moieties. The superior proton-exchange membrane fuel cell performance of SnNC cathode catalysts under realistic, hydrogen–air fuel cell conditions, particularly after NH 3 activation treatment, makes them a promising alternative to today’s state-of-the-art Fe-based catalysts.

25 ENERGY STORAGE↗
DOE OSTI2018

Chapter 3. Understanding the Effects of Composition and Structure on the Oxygen Evolution Reaction (OER) Occurring on NiFeOx Catalysts. IN: Energy and Environment Series No. 22, Integrated Solar Fuel Generators

© The Royal Society of Chemistry 2019. Hydrogen produced by wind- or solar energy-driven electrochemical splitting of water could be used to store renewable electrical energy or to reduce biomass or CO2 to carbon-containing fuels. The potential required for the splitting of water is larger than the thermodynamic potential due to the insufficient activity of the catalysts required for the two half reactions involved in water splitting - the oxygen evolution reaction (OER) and the hydrogen evolution reaction (HER). The OER and HER occur at the anode and cathode, respectively, of the electrochemical cell. Since the overpotential for the OER can be nearly an order of magnitude larger than that for the HER, considerable attention has been devoted to finding and developing highly active OER catalysts, and in particular those based on earth-abundant elements. To date this goal has been best met with catalysts based on oxides and oxyhydroxides of Ni and Fe for alkaline electrolysis. This chapter reviews the current understanding of such catalysts and examines the role of catalyst synthesis method and percentage of Fe content on catalyst performance. Particular attention is given to the role of Fe3+ cations exchanged into the lattice of NiOOH in enhancing the OER activity of the host material. This issue is discussed from both experimental and theoretical perspectives with the aim of identifying how and why the additions of Fe3+ cations enhance catalyst performance. The chapter ends with a brief overview of recent efforts aimed at identifying elements other than Fe that can be added to Ni oxide to enhance its OER activity and elements that can be added to NiFe oxyhydroxides to further enhance their OER activity.

Bell, Alexis T↗
DOE OSTI2022

Synergistic promotion of transition metal ion-exchange in TiO 2 nanoarray-based monolithic catalysts for the selective catalytic reduction of NO x with NH 3

TiO 2 supported catalysts have been widely studied for the selective catalytic reduction (SCR) of NO x ; however, comprehensive understanding of synergistic interactions in multi-component SCR catalysts is still lacking. For this work, transition metal elements (V, Cr, Mn, Fe, Co, Ni, Cu, La, and Ce) were loaded onto TiO 2 nanoarrays via ion-exchange using protonated titanate precursors. Amongst these catalysts, Mn-doped catalysts outperform the others with satisfactory NO conversion and N 2 selectivity. Cu co-doping into the Mn-based catalysts promotes their low-temperature activity by improving reducibility, enhancing surface Mn 4+ species and chemisorbed labile oxygen, and elevating the adsorption capacity of NH 3 and NO x species. While Ce co-doping with Mn prohibits the surface adsorption and formation of NH 3 and NO x derived species, it boosts the N 2 selectivity at high temperatures. By combining Cu and Ce as doping elements in the Mn-based catalysts, both the low-temperature activity and the high-temperature N 2 selectivity are enhanced, and the Langmuir–Hinshelwood reaction mechanism was proved to dominate in the trimetallic Cu–Ce–5Mn/TiO 2 catalysts due to the low energy barrier.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Mechanistic insights into metal, nitrogen doped carbon catalysts for oxygen reduction: progress in computational modeling

We report metal and nitrogen doped carbon materials (denoted as M–N–C) synthesized through high-temperature pyrolysis have been found to exhibit activity for oxygen reduction reaction (ORR) approaching that of Pt and electrochemical stability higher than previous MN 4 -containing macrocyclic molecular catalysts. Tremendous efforts have thus been devoted to the advancement of M–N–C catalysts as an economical alternative to Pt-based catalysts for proton exchange membrane fuel cell cathodes with a focus on simultaneously improving activity and stability. To this end, novel computational modeling techniques have been developed and applied to acquire knowledge crucial for accelerating the pace of M–N–C catalyst development. In this review, recent progress in computational method development, as well as the predictions of chemical structure of active sites, reaction pathways, ORR kinetics, and catalyst stability in electrochemical environments, are critically surveyed. Moreover, the crucial role of computational modeling to elucidate the functional mechanism of M–N–C catalysts for ORR in acid media and enable rational design of M–N–C catalysts is discussed with a visionary outlook for the field.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

Many-Body Quantum Catalysts for Transforming Between Phases of Matter

A catalyst is a substance that enables otherwise impossible transformations between states of a system, without being consumed in the process. In this work, we apply the notion of catalysts to many-body quantum physics. In particular, we construct catalysts that enable transformations between different symmetry-protected topological (SPT) phases of matter using symmetric finite-depth quantum circuits. We discover a wide variety of catalysts, including GHZ-like states that spontaneously break the symmetry, gapless states with critical correlations, topological orders with symmetry fractionalization, and spin-glass states. These catalysts are all united under a single framework that has close connections to the theory of quantum anomalies, and we use this connection to put strong constraints on possible pure- and mixed-state catalysts. We also show how the catalyst approach leads to new insights into the structure of certain phases of matter, and to new methods to efficiently prepare SPT phases with long-range interactions or projective measurements.

quantum many-body systems↗
DOE OSTI2021

Mitigation of PtCo/C Cathode Catalyst Degradation via Control of Relative Humidity

Maintaining the high performance of proton-exchange membrane fuel cells (PEMFC) over the course of its lifetime is a key enabling factor for its successful commercialization as a primary power source in zero-emission transportation applications. In this context, it is important to mitigate the degradation of PtCo-alloy based cathode catalysts used for oxygen reduction reaction (ORR). PtCo-alloy catalysts exhibit high activity at beginning-of-life (BOL) which tends to decrease during operation due to loss of electrochemical surface area (ECSA) and dissolution-contamination related effects of the Co-alloying component. Here, we demonstrate the use of relative humidity (RH) of the inlet gases as a controllable parameter to mitigate the degradation of PtCo-alloy catalyst degradation. We employ a catalyst-specific voltage cycling accelerated stress test (AST) durability protocol as a function of inlet RH to degrade PtCo catalysts. A series of in situ electrochemical diagnostics and ex situ characterizations have been carried out to investigate the catalyst layer characteristics at end-of-test (EOT). Our results show that at sub-saturated conditions of durability protocol operation, PtCo catalyst sustains higher EOT H 2 /air performance due to better retention of ECSA and smaller impact of Co 2+ dissolution/contamination.

25 ENERGY STORAGE↗
DOE OSTI2022

Investigating the Particle Growth in Bimodal Pt/C Catalysts by In-Situ Small-Angle X-ray Scattering: Challenges in the Evaluation of Stress Test Protocol-Dependent Degradation Mechanisms

The influence of different combinations of accelerated stress test (AST) protocols simulating load-cycle and start/stop conditions of a proton exchange membrane fuel cell (PEMFC) vehicle is investigated on a bimodal Pt/C catalyst. The bimodal Pt/C catalyst, prepared by mixing two commercial catalysts, serves as a model system and consists of two distinguishable size populations. The change in mean particle size was investigated by in situ small-angle X-ray scattering (SAXS). The comparison to the reference catalysts, i.e., the two single-size population catalysts, uncovers the presence of electrochemical Ostwald ripening as a degradation mechanism in the bimodal catalyst. Increasing the harshness of the applied AST protocol combinations by faster changing between load-cycle or start/stop conditions, the particle size of the larger population of the bimodal catalyst increases faster than expected. Surprisingly, the change in mean particle size of the smaller size population indicates a smaller increase for harsher AST protocols, which might be explained by a substantial electrochemical Ostwald ripening.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2018

Lignin-Derived Carbon Fibers as Efficient Heterogeneous Solid Acid Catalysts for Esterification of Oleic Acid

Here, the production of biodiesel by the esterification of oleic acid, as an example of free fatty acid (FFA), was explored by using a new solid acid catalyst derived from lignin, a highly abundant low-cost biomass material. The catalyst was synthesized from lignin-derived carbon fiber by straightforward sulfonation and contains 1.86 mmol/g of sulfonic acid (-SO 3 H) groups. The catalyst was characterized by a variety of techniques including PXRD, TGA, TPD-MS, SEM, and XPS to understand the surface chemistry and the result of sulfonation. It was found that the sulfonated lignin-derived carbon fiber (CF-SO 3 H) catalyst was very efficient at esterifying oleic acid at 80 o C in 4 hours, with 10 wt. % catalyst (in terms of oleic acid content) and at a 10:1 molar ratio of methanol: oleic acid with a yield of 92%. Furthermore, the catalyst can be reused with no significant loss in activity after 4 cycles. Hence, synthesizing solid acid catalysts from lignin-derived carbon fiber affords a novel strategy for producing biodiesel via ‘green chemistry’.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Oxygen Reduction on Platinum-Nickel and Platinum-Cobalt Alloy Based Catalysts for High Temperature Proton Exchange Membrane Fuel Cells

Catalyst layers, with commercial PtNi/TKK (TECNiE52; platinum 46.5 wt%), PtCo/TKK (TEC36E52; platinum 45.8 wt%) catalysts, and an in-house catalyst PtNi-NC (platinum 38.4 wt%), synthesised using acoustic mixer and a tube furnace, are prepared using three different ionomers: 20 wt% Nafion®, 60 wt% polytetrafluoroethylene (PTFE), and an in-house 5 wt% ionomer (‘Ionomer X’). These inks are bar-coated onto carbon paper gas diffusion layers (GDLs), which are cut into 3 cm × 5 cm pieces. The coated layers are tested for oxygen reduction in a commercial gas diffusion electrode (GDE) test cell, FlexCell® (Gaskatel GmbH, Germany), using 85 wt% phosphoric acid at both room temperature and at 155°C. This study evaluates the polynorbornene (PNB)-based in-house ionomer performance as binder and in-house catalyst oxygen reduction reaction (ORR) activity in comparison to commercial products. The catalyst layers are characterised using X-ray diffraction (XRD) analysis, X-ray photoelectron spectroscopy (XPS), and high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM). Among the catalyst layers prepared with PTFE ionomer and tested at 155°C, the in-house catalyst demonstrates the highest ORR activity. Ionomer X proves to be a good candidate to be used as a per- and polyfluoroalkyl-free binder for high-temperature (HT) proton exchange membrane fuel cell (PEMFC) applications.

85 wt% phosphoric acid↗
DOE OSTI2015

Biomimetic catalysts responsive to specific chemical signals

Part 1. Design of Biomimetic Catalysts Based on Amphiphilic Systems The overall objective of our research is to create biomimetic catalysts from amphiphilic molecules. More specifically, we aim to create supramolecular systems that can be used to control the microenvironment around a catalytic center in a biomimetic fashion and apply the learning to construct supramolecular catalysts with novel functions found in enzymatic catalysts. We have prepared synthetic molecules (i.e., foldamers) that could fold into helical structures with nanometer-sized internal hydrophilic cavities. Cavities of this size are typically observed only in the tertiary and quaternary structures of proteins but were formed in our foldamer prepared in just a few steps from the monomer. Similar to many proteins, our foldamers displayed cooperativity in the folding/unfolding equilibrium and followed a two-state conformational transition. In addition, their conformational change could be triggered by solvent polarity, pH, or presence of metal ions and certain organic molecules. We studied their environmentally dependent conformational changes in solutions, surfactant micelles, and lipid bilayer membranes. Unlike conventional rigid supramolecular host, a foldamer undergoes conformational change during guest binding. Our study in the molecular recognition of an oligocholate host yielded some extremely exciting results. Cooperativity between host conformation and host–guest interactions was found to “magnify” weak binding interactions. In other words, since binding affinity is determined by the overall change of free energy during the binding, guest-induced conformational change of the host, whether near or far from the binding site, affects the binding. This study has strong implications in catalysis because enzymes have been hypothesized to harvest similar intramolecular forces to strengthen their binding with the transition state of an enzyme-catalyzed reaction. The supramolecular and amphiphilic principles used in the foldamer catalysts were extended to a few other systems, particularly to interfacially cross-linked reverse micelles and micelles. These features enabled unusual catalytic features such as basic/nucleophilic catalysis under acidic conditions. We were able to create highly active metal nanoclusters catalysts whose local environment could be tuned by the organic framework. We were even able to create a “catalytic nanomachine” that grabs the substrate to the encapsulated Au clusters, which efficiently convert the substrate to the product that is rapidly ejected due to its different binding properties. Our research has important impacts on fundamental and applied energy-related sciences. On the fundamental level, it tests important biocatalytic principles on relatively simple synthetic systems and is expected to afford deeper understanding of biological catalysis. On the practical level, the research is anticipated to lead to “smart” catalysts and open up exiting applications in chemical analysis, reaction control, and materials synthesis. Part 2. Electrochemical Reduction of CO₂ The primary objective of our research involving the electrochemical reduction of carbon dioxide is to apply a multidisciplinary approach toward developing a greater understanding of the problem of efficiently converting CO₂ to hydrocarbons through electrochemical routes. Our goal is to provide a better understanding of the principles that underlie the electrocatalytic reduction of CO₂ at electrode surfaces and the molecular pathways that lead to desired compounds. This understanding is essential for the design and development of new catalytic materials for the selective production of renewable feedstocks. The electrochemical reduction of CO₂ involves the formation of various reaction products and adsorbed intermediates whose distribution depends upon the nature of the electrode material and the electrochemical conditions, including applied potential, solvent, and electrolyte, used during reduction. Our efforts are focused on developing a detailed picture of how these various parameters impact the reaction pathway for CO₂ reduction and to tune this reaction to favor the formation of specific products by careful selection of electrode materials and reaction conditions. Our experimental plan includes a detailed examination of the electrode material as well as a quantitative evaluation of the reaction conditions using several in-situ analysis tools that give a direct measure of adsorbed and solution species that appear during CO₂ reduction. During the first year of funding for this aspect of the project, we have developed an on-line electrochemical measurement tool utilizing membrane-introduction mass spectrometry to detect reactions products directly during the electrochemical reduction of CO₂on various sputtered electrode materials. In addition, we have examined the role of a selection of different electrode compositions (including single component and binary electrodes) on product distributions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2016

Templating Routes to Supported Oxide Catalysts by Design

The rational design and understanding of supported oxide catalysts requires at least three advancements, in order of increasing complexity: the ability to quantify the number and nature of active sites in a catalytic material, the ability to place external controls on the number and structure of these active sites, and the ability to assemble these active sites so as to carry out more complex functions in tandem. As part of an individual investigator research program that is integrated with the Northwestern University Institute for Catalysis in Energy Processes (ICEP) as of 2015, significant advances were achieved in these three areas. First, phosphonic acids were utilized in the quantitative assessment of the number of active and geometrically-available sites in MO x -SiO 2 catalysts, including nanocrystalline composites, co-condensed materials, and grafted structures, for M=Ti, Zr, Hf, Nb, and Ta. That work built off progress in understanding supported Fe, Cu, and Co oxide catalysts from chelating and/or multinuclear precursors to maximize surface reactivity. Secondly, significant progress was made in the new area of using thin oxide overcoats containing ‘nanocavities’ from organic templates as a method to control the dispersion and thermal stability of subsequently deposited metal nanoparticles or other catalytic domains. Similar methods were used to control surface reactivity in SiO 2 -Al 2 O 3 acid catalysts and to control reactant selectivity in Al 2 O 3 -TiO 2 photocatalysts. Finally, knowledge gained from the first two areas has been combined to synthesize a tandem catalyst for hydrotreating reactions and an orthogonal tandem catalyst system where two subsequent reactions in a reaction network are independently controlled by light and heat. Overall, work carried out under this project significantly advanced the knowledge of synthesis-structure-function relationships in supported oxide catalysts for energy applications.

02 PETROLEUM↗
DOE OSTI2020

Artificial Photosynthesis with Next Generation Molecular Catalysts

The objective of this project was to develop a new class of molecular photocatalysts for CO 2 reduction that will enable breakthrough advances in artificial photosynthesis. A major limitation of existing photocatalytic assemblies is that only a small fraction of absorbed photons are converted into fuel due to inefficiencies in electron transport between the different system components. In the case of molecular catalysts for reduction of CO 2 , highly reducing electron equivalents are required for catalysis. As a result, the electron flux between the photosensitizer and CO 2 reduction catalyst is heavily biased towards the photosensitizer. One method to direct the electron flux towards productive photocatalysis is to design molecular catalysts for CO 2 reduction that operate at more favorable potentials than existing catalysts. The conventional approach is to tune the potential of the catalyst through selection of the supporting ligands, however, this only leads to incremental improvements due to the existence of an unfavorable scaling relationship between the rate and potential of catalysis. Our hypothesis is that the catalytic rate and potential can be simultaneously enhanced using bimetallic catalysts in which one metal improves the potential of catalysis and the second metal increases the rate of catalysis. During the course of this project, a few studies reported some success in improving photocatalytic CO 2 reduction with heterobimetallic complexes, demonstrating the potential of this approach to catalyst design.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Multi-state Catalysts Modulated by Mechanical Force (Final Report)

The development of more efficient catalytic processes and new approaches to control catalytic activity and selectivity are central to the realization of more selective, atom economic, and energy efficient routes to value added chemicals and polymers. The reactivity and selectivity of a transition metal catalyst is intimately related to the ligand-sphere geometry and, in many cases, the ideal ligand geometry for one step of a catalytic cycle is poorly matched to the ideal ligand geometry for another, resulting in sub-optimal efficiency. Macroscopic mechanical forces are both large, potentially much larger than interatomic forces, and are directional and localized to an extent that differentiates them from other forms of energy input such as heat or light. As such, mechanical force represents a heretofore untapped approach to modulate catalyst geometry, with the potential to reversibly modulate catalyst geometry on the timescale of catalytic turnover or monomer enchainment. This project has addressed the fundamental challenges in material-to-molecule strain coupling associated with the development of a new class of mechanically responsive catalysts (mechanocatalysts) in which active organotransition metal catalysts are strategically embedded in a flexible polymer network such that application of external mechanical force (stretching or deformation) leads to modulation of catalyst geometry, and hence reactivity and selectivity. Our efforts during the tenure of this grant were directed toward the elucidation of force-reactivity relationships of elementary transformations that occur within the first coordination sphere of a transition metal complex employing stiff stilbene photoswitches tethered to a flexible bidentate phosphine ligand derived from MeOBiphep as molecular force probes which provide a range of compressive and extension forces to the coupled transition metal complex depending on the geometry of the stiff stilbene and length of the tethering chains. During the tenure of this grant, we have quantified the rate of C(sp 2 )-C(sp 2 ) reductive elimination from platinum(II) diaryl complexes containing bis(phosphine) force probe ligands as a function of mechanical force; compressive forces decreased the rate of reductive elimination whereas extension forces increased the rate relative to the strain-free MeOBiphep complex with a 3.4-fold change in rate over a ~290 pN range of restoring forces. In a similar manner, we have quantified the rate of oxidative addition of bromobenzene to low-ligated palladium(0) complexes containing force probe ligands as a function of mechanical force; compressive forces increase the rate of oxidative addition, whereas tensile forces decrease the rate with a ~6 fold change in rate across ~340 pN of force applied to the complexes. In both cases, experimental and computational analyses argue strongly against any significant force-induced perturbation of ground state geometry within the first coordination sphere of the reactant complexes. Rather, the force/rate behavior observed for these transformations across these ranges of forces is attributed to the coupling of force to the nuclear motion comprising the reaction coordinates for reductive elimination and oxidative addition. These results together inform the development of catalysts whose activity can be tuned by an external force that is adjusted within a catalytic cycle and suggest opportunities to experimentally map geometry changes associated with reactions in transition metal complexes and potential strategies for force-modulated catalysis.

99 GENERAL AND MISCELLANEOUS↗