Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Additives”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57

Evaluation of several additional dry lubricants for spacecraft applications

Four transfer-film ball-bearing retainer materials were evaluated for their lubricating ability and wear capability under conditions of 120-gram radial load, 450-gram axial load, 3600-rpm unidirectional rotation, 23 C ambient temperature, and less than .1 microtorr pressure, using R-2 sized unshielded ball bearings. The 'stop-test' criterion was a total of one billion revolutions or a torque buildup greater than 18 gm-cm per bearing pair. A PTFE-fiberglass-MoS2 composite, a PTFE-bronze composite, and a tantalum-molybdenum-MoS2 composite operated for one billion revolutions without reaching the 18-gram torque limit. A p-oxybenzoyl polymer-MoS2 composite operated sixteen million revolutions before reaching the 18-gm cm stop-test torque. The first three materials are considered as suitable lubricants under the test conditions employed.

Vest, C. E.↗

Detection of weldment lack of fusion using opaque additives

Problems in the production of aluminum weldments are caused by moisture absorbed by the aluminum oxide which forms on the surface before welding. Another problem is incomplete penetration of the weldment. The problems can be solved by coating the aluminum surfaces with an X-ray-opaque metal such as silver or copper. This will prevent the formation of moisture-absorbing aluminum oxide. Any protective coating remaining in an area of incomplete weld penetration can be seen in an inspection of the weldment conducted with the aid of an X-ray method. Details of copper deposition procedures are discussed along with a copper coating analysis and the testing of the weldments.

Cook, J. L.↗

The effectiveness of correcting codes in reception in the whole in additive normal white noise

Some possible criteria for estimating the effectiveness of correcting codes are presented, and the energy effectiveness of correcting codes is studied for symbol-by-symbol reception. Expressions for the energetic effectiveness of binary correcting codes for reception in the whole are produced. Asymptotic energetic effectiveness and finite signal/noise ratio cases are considered.

Shtarkov, Y. M.↗

Snow survey and vegetation growth in high mountains (Swiss Alps) and additional ERTS investigations in Switzerland

The author has identified the following significant results. Two different methods, an analog and a digital one, have been developed for rapid and accurate mapping of the areal extent and changes in snow cover in high mountains. The quick-look method is based on individual visual control of each image using a photo quantizer which provides exact references for density slicing with high resolution lith-film. The digital snow classification system is based on discriminant analysis with the data of the four multispectral bands as variables and contains all preprocessing, feature extraction, and mapping steps for an operational application. Two different sets of sampling groups were established which apply to different conditions of snow cover. The first one serves for the normal situation with a uniform dry and new cover. The second one serves for situations with partly thawing and/or frozen snow.

Haefner, H.↗

Addition of oxygen to and distribution of oxides in tantalum alloy T-111 at low concentrations

Oxygen was added at 820 and 990 C at an oxygen pressure of about .0003 torr. The technique permitted predetermined and reproducible oxygen doping of the tantalum alloy (T-111). Based on the temperature dependency of the doping reaction, it was concluded that the initial rates of oxygen pickup are probably controlled by solution of oxygen into the T-111 lattice. Although hafnium oxides are more stable than those of tantalum or tungsten, analyses of extracted residues indicate that the tantalum and tungsten oxides predominate in the as-doped specimens, presumably because of the higher concentrations of tantalum and tungsten in the alloy. However, high-temperature annealing promotes gettering of dissolved oxygen and oxygen from other oxides to form hafnium oxides. Small amounts of tantalum and tungsten oxides were still present after high temperature annealing. Tungsten oxide (WO3) volatilizes slightly from the surface of T-111 at 990 C but not at 820 C. The vaporization of WO3 has no apparent effect on the doping reaction.

Stecura, S.↗

Development of autoclave moldable addition-type polyimides

Chemistry and processing modifications of the poly(Diels Alder) polyimide (PDA) resin were performed to obtain structural composites suitable for 589 K (600 F) service. This work demonstrated that the PDA resin formulation is suitable for service at 589 K (600 F) for up to 125 hours when used in combination with Hercules HTS graphite fiber. Sandwich panels were autoclave molded using PDA/HTS skins and polyimide/glass honeycomb core. Excellent adhesion between honeycomb core and the facing skins was demonstrated. Fabrication ease was demonstrated by autoclave molding three-quarter scale YF-12 wing panels.

Vaughan, R. W.↗

Radiometric diameters for an additional 22 asteroids

Ten-micron radiometry of 24 asteroids, 22 of which have not previously had their diameters and albedos determined, is presented. The magnitudes of the objects ranged from -0.35 to +5.35 and 13 of them had diameters smaller than 100 km. They ranged in albedo from 0.024 to 0.28, and the 22 previously unstudied objects included 10 C asteroids, seven S asteroids, three U asteroids, and two unknown. In the diameter-albedo plane, ten of the asteroids studied clustered near albedo 0.03 and diameter 100-200 km, in a region previously occupied by only seven asteroids but where Chapman et al. (1975) predicted many objects would be identified upon sampling those fainter than V equals about 12. The new data suggest that there are substantial numbers of S asteroids with diameter less than 100 km in the inner part of the belt.

Morrison, D.↗

Investigation of a new stony meteorite from Mauritania with some additional data on its find site - Aouelloul crater

The Zerga meteorite, a small stony meteorite found at Aouelloul crater, is a fragment of a larger mass with a pre-atmospheric radius between 20 and 125 cm. The meteorite is a typical amphoterite, with monomict brecchia which has undergone at least one recrystallization episode. The terrestrial age of the meteorite is roughly an order of magnitude smaller than the K-Ar gas-retention age (about 3.1 million years) of the glassy impactite found at the crater, which is close to the age of the nearby Tenoumer crater (about 2.5 million years). The similar ages of the two craters, together with their alignment with the Temimichat Ghallaman crater, suggest a simultaneous triple impact following the disruption of a large meteorite moving on a very shallow earth trajectory. The unusually shallow original depths inferred for two of the craters may be explained by low impact angles.

Fudali, R. F.↗

Additional experiments with a four-bladed cyclic pitch stirring model rotor, part 2 of second yearly report

The four bladed pitch stirring rotor model was used in a rotor dynamic wake survey at zero advance ratio, covering 2 deg, 5 deg and 8 deg collective pitch settings. Dynamic wake data were taken in planes .12 and .20 radii below the rotor disk and are to be compared with analytical wake data with parameters to be identified from pitch stirring transients. The model was modified to perform such transients. The instrumentation developed for this purpose is described together with the method of data acquisition and with the test procedures. The hardware and software for several data handling systems are discussed. These systems extract from pitch stirring transients the parameters of analytical dynamic rotor wake models.

Hohenemser, K. H.↗

Additional studies of forest classification accuracy as influenced by multispectral scanner spatial resolution

First, an analysis of forest feature signatures was used to help explain the large variation in classification accuracy that can occur among individual forest features for any one case of spatial resolution and the inconsistent changes in classification accuracy that were demonstrated among features as spatial resolution was degraded. Second, the classification rejection threshold was varied in an effort to reduce the large proportion of unclassified resolution elements that previously appeared in the processing of coarse resolution data when a constant rejection threshold was used for all cases of spatial resolution. For the signature analysis, two-channel ellipse plots showing the feature signature distributions for several cases of spatial resolution indicated that the capability of signatures to correctly identify their respective features is dependent on the amount of statistical overlap among signatures. Reductions in signature variance that occur in data of degraded spatial resolution may not necessarily decrease the amount of statistical overlap among signatures having large variance and small mean separations. Features classified by such signatures may thus continue to have similar amounts of misclassified elements in coarser resolution data, and thus, not necessarily improve in classification accuracy.

Sadowski, F. E.↗

Weldability of high-toughness iron - 12 percent-nickel alloys with reactive metal additions of titanium, aluminum, or niobium

Three exceptionally high toughness Fe-12Ni alloys designed for cryogenic service were welded by using the gas tungsten arc welding process. Evaluation of their weldability included equivalent energy fracture toughness tests, transverse weld tensile tests at -196 and 25 C, and weld crack sensitivity tests. The Fe-12Ni-0.25Ti alloy proved extremely weldable for cryogenic applications, having weld and heat affected zone properties comparable to those of the wrought base alloy. The Fe-12Ni-0.5Al alloy had good weld properties only after the weld joint was heat treated. The Fe-12Ni-0.25Nb alloy was not considered weldable for cryogenic use because of its poor weld joint properties at -196 C and its susceptibility to hot cracking.

Delvetian, J. H.↗

Additional comments on 'Multistage least-squares parameter estimation'

The purpose of this correspondence is to call attention to other solutions to the problem addressed in the above paper, that of adding or deleting parameters or measurements from a given linear model. The solution algorithms proposed in the article are numerically ill-conditioned and are less efficient, in terms of both computational and storage requirements, than the methods described here. Several numerically stable, compact, flexible, and efficient algorithms for analyzing the parameter estimation problem are described and others are referenced.

Bierman, G. J.↗

Antistatic additive for polyimide films

Thin polyimide films are given excellent antistatic properties even at high temperature by low-level loading with lithium salts. Extremely hygroscopic, these salts absorb a layer of atmospheric water that provides conductive paths allowing charges to dissipate.

Sarbolouki, M. N.↗

Addition of rigid elements to NASTRAN

Four rigid elements, namely, a rigid rod element (CRIGDR) and three rigid body elements (CRIGD1, GRIGD2 and CRIGD3), have recently been added to NASTRAN and will be available in the next public release of the program. The theoretical formulation, the bulk data information and the programming details pertaining and realistic problems are illustrated by employing them in the solution of two helicopter structural analysis problems.

Pamidi, P. R.↗

Study of the potential for improving the economics of hydrogen liquefaction through the use of centrifugal compressors and the addition of a heavy water plant

An approach to the liquefaction of hydrogen was developed which permits the application of standard centrifugal compressors in place of reciprocating machines. A second fluid, such as propane, is added to the hydrogen prior to compression to form a mixture having a molecular weight much greater than that of hydrogen alone, so that a standard centrifugal compressor can be used. After compression, the mixture is cooled to cryogenic temperature levels where the propane condenses out of the mixture and is separated as a liquid. Since a small amount of deuterium is produced during hydrogen liquefaction, the potential of recovering deuterium and selling it as a co-product was investigated. Deuterium, in the form of heavy water, can be used in certain nuclear reactors as a neutron moderator to reduce the neutron velocity and enhance the probability of neutron collision with uranium nucleii.

Baker, C. R.↗