Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AIR FLOW”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Skin friction measurement with partially exposed polymer dispersed liquid crystals

Partially exposed polymer dispersed liquid crystal thin film (10-25 microns) deposited on a flat glass substrate has been used for the first time to measure skin friction. Utilizing the shear-stress-induced director reorientation in the partially exposed liquid-crystal droplets, optical transmission under crossed polarization has been measured as a function of the air flow differential pressure. Direct measurement of the skin friction with a skin friction drag balance, under the same aerodynamic conditions, lets us correlate the skin friction with optical transmission. This provides a unique technique for the direct measurement of skin friction from the transmitted light intensity. The results are in excellent agreement with the model suggested in this paper.

Parmar, D. S.↗
NASA NTRS1993

Contributions of microgravity test results to the design of spacecraft fire-safety systems

Experiments conducted in spacecraft and drop towers show that thin-sheet materials have reduced flammability ranges and flame-spread rates under quiescent low-gravity environments (microgravity) compared to normal gravity. Furthermore, low-gravity flames may be suppressed more easily by atmospheric dilution or decreasing atmospheric total pressure than their normal-gravity counterparts. The addition of a ventilating air flow to the low-gravity flame zone, however, can greatly enhance the flammability range and flame spread. These results, along with observations of flame and smoke characteristics useful for microgravity fire-detection 'signatures', promise to be of considerable value to spacecraft fire-safety designs. The paper summarizes the fire detection and suppression techniques proposed for the Space Station Freedom and discusses both the application of low-gravity combustion knowledge to improve fire protection and the critical needs for further research.

Friedman, Robert↗
NASA NTRS1992

Tests characterizing bioprocessor hardware for analytical modeling

The tests outlined in this paper were used to characterize the hardware components of the Salad Machine, a small NASA-developed bioprocessor. The data from these tests are presented, and the methods by which this data can be integrated into system mathematical models are briefly discussed. The subsystems and physical processes discussed include the lighting system, the air loop (condensing heat exchanger and the blower), heat transfer to the surroundings, and leakage. Through this effort it was learned that in the development of a test protocol, care should be taken to order the tests such that environmental parameters, particularly humidity, require as few large adjustments as possible. Sensor calibration and installation take a substantial amount of time, which should be built into the test schedule. Two properties were particularly hard to quantify: the air flow rate and the energy from the lighting system entering into the growth volume. Flow rate can be measured using the appropriate device for the system configuration and airflow. Lighting system radiation level was measured using three methods. The results of these methods varied substantially, putting off conclusive quantification of this value.

Gustavino, S.↗
NASA NTRS1992

Energy and radiation balance components for three grass surfaces near Kursk, Russia

The energy and radiation balance components were determined over three grass surfaces, located on the Streletskaya steppe during July 1991. The Bowen ratio energy balance method was used to determine the sensible and latent heat flux densities using six computer controlled systems. A total of 126 variables were sampled, including global, diffuse, and reflected solar radiation, long wave radiation (up and down), net radiation, photosynthetically active radiation above and below the vegetation, infrared surface temperatues, soil temperature and heat flow, air temperature and vapor pressure at two levels, wind speed and direction, and precipitation. The ranking of the sites from greatest to smallest for net radiation and latent heat flux density were preserve, mowed in 1990, and mowed in 1991. The ranking of the sites from greatest to smallest for sensible heat flux density were mowed in 1990, mowed in 1991, and preserve.

Fritschen, Leo J.↗
NASA NTRS1921

The Determination of the Effective Resistance of a Spindle Supporting a Model Airfoil

An attempt was made to determine the effect of spindle interference on the lift of the airfoil by measuring moments about the axis parallel to the direction of air flow. The values obtained are of the same degree as the experimental error, and for the present this effect will be neglected. The results obtained using a U.S.A. 15 wing (plotted here) show that the correction is nearly constant from 0 degrees to 10 degrees incidence and that at greater angles its value becomes erratic. At such angles, however, the wing drag is so high that the spindle correction and its attendant errors become relatively small and unimportant.

Davidson, W E↗
NASA NTRS1923

Notes on aerodynamic forces on airship hulls

For a first approximation the air flow around the airship hull is assumed to obey the laws of perfect (i.e. free from viscosity) incompressible fluid. The flow is further assumed to be free from vortices (or rotational motion of the fluid). These assumptions lead to very great simplifications of the formulae used but necessarily imply an imperfect picture of the actual conditions. The value of the results depends therefore upon the magnitude of the forces produced by the disturbances in the flow caused by viscosity with the consequent production of vortices in the fluid. If these are small in comparison with the forces due to the assumed irrotational perfect fluid flow the results will give a good picture of the actual conditions of an airship in flight.

Tuckerman, L B↗
NASA NTRS1929

Wind Tunnel Tests on an Airfoil Equipped with a Split Flap and a Slot

The investigation described in this report is concerned with the changes in the aerodynamic characteristics of an airfoil which are produced by a gauze-covered suction slot, located near the leading edge, and connected by an air passage to a split flap at the trailing edge. The tests were conducted at the Langley Memorial Aeronautical Laboratory. At the larger values of lift coefficient where the action of the slot might be expected to be most effective, the pressure differences were such that the air flowed out of the slot rather than in through it, and in consequence, the maximum lift coefficient was decreased.

Bamber, Millard J↗
NASA NTRS1931

A suggested method for measuring turbulence

The desirability of a quantitative measure of turbulence is emphasized, and a possible method of attack on the problem is discussed. Data are presented to show that the hot-wire anemometer has possibilities as an instrument for measuring turbulence. An apparatus consisting essentially of two hot wire, one parallel to the air flow and one at right angles to it, is suggested.

Taylor, Fayette C↗
NASA NTRS1932

The Effect of Clearance Distribution on the Performance of a Compression-ignition Engine with a Precombustion Chamber

The clearance distribution in a precombustion chamber cylinder head was varied so that for a constant compression ratio of 13.5 the spherical auxiliary chambers contained 20, 35, 50, and 70 per cent of the total clearance volume. Each chamber was connected to the cylinder by a single circular passage, flared at both ends, and of a cross-sectional area proportional to the chamber volume, thereby giving the same calculated air-flow velocity through each passage. Results of engine-performance tests are presented with variations of power, fuel consumption, explosion pressure, rate of pressure rise, ignition lag, heat loss to the cooling water, and motoring characteristics. For good performance the minimum auxiliary chamber volume, with the cylinder head design used, was 35 per cent of the total clearance volume; for larger volumes the performance improves but slightly. With the auxiliary chamber that contained 35 percent of the clearance volume there were obtained the lowest explosion pressures, medium rates of pressure rise, and slightly less than the maximum power. For all clearance distributions an increase in engine speed decreased the ignition lag in seconds and increased the rate of pressure rise.

Moore, C. S.↗
NASA NTRS1936

Full-scale Wind-tunnel to Determine a Satisfactory Location for a Service Pitot-static Tube on a Low-wing Monoplane

Surveys of the air flow over the upper surface of four different airfoils were made in the full-scale wind tunnel to determine a satisfactory location for a fixed Pitot-static tube on a low-wing monoplane. The selection was based on small interference errors, less than 5 percent, and on a consideration of structural and ground handling problems. The most satisfactory location on the airfoils without flaps that were investigated was 10 percent of the chord aft and 25 percent of the chord above the trailing edge of a section approximately 40 percent of the semispan inboard of the wing tip. No satisfactory location was found near the wing when the flaps were deflected.

Parsons, John F↗
NASA NTRS1940

A study of the air movement in two aircraft-engine cylinders

Studies were made of the air movements in the NACA glass-cylinder apparatus using cylinder heads similar to those on the Wright R-1820-G engine and the Pratt & Whitney Wasp engine as modified by the Eclipse Aviation Corporation to use fuel-injection equipment. The air movements were made visible by mixing small feathers with the air; high-speed motion pictures were than taken of the feathers as they swirled about the inside the glass cylinder. The test engine speeds were 350, 500, and 1,000 r.p.m. Motion pictures were also taken of gasoline sprays injected into the cylinder during the intake stroke. The air flow produced by each cylinder head is described and some results of the velocity measurements of feathers are presented. The apparent time intervals required for vaporization of the gasoline sprays are also given.

Lee, Dana W↗
NASA NTRS1922

Deflection of Propeller Blades While Running

The forces acting on the blades of a propeller proceed from the mass of the propeller and the resistance of the surrounding medium. The magnitude, direction and point of application of the resultant to the propeller blade is of prime importance for the strength calculation. Since it was obviously impracticable to bring any kind of testing device near the revolving propeller, not so much on account of the element of danger as on account of the resulting considerable disturbance of the air flow, the deflection in both cases was photographically recorded and subsequently measured at leisure.

PROPELLERS - DEFLECTION↗
NASA NTRS1950

Investigation of Ignition Characteristics of AN-F-32 and Two An-f-58a Fuels in Single Can-type Turbojet Combustor

Ignition characteristics of AN-F-32 and two AN-F-58a fuels were studied in a single can-type turbojet combustor under air-flow conditions representing engine speeds of 1600, 2500, and 4000 rpm, altitudes from sea level to 30,000 feet, ambient temperatures at sea level from 90 degrees to minus 36 degrees F, and flight Mach numbers of 0 and 0.6. Critical fuel-flow rates for ignition increased with increase in preignition engine speed, with increase in altitude, or with decrease in sea-level ambient temperature. This flow rate appears to increase in a direct relation to decrease in fuel volatility as indicated by the 10-percent-evaporated temperature.

Rayle, Warren D↗
NASA NTRS1951

Effect of spark repetition rate on the ignition limits of a single tubular combustor /Hampton H. Foster

The effect of spark repitition rate on the altitude ignition limits of a single tubular (turbojet engine) combustor was investigated. An increase in sparking rate from 3 to 140 sparks per second reduced the ignition limiting combustor-inlet pressure about 2 to 4 inches of mercury for air-flow rates of 1.87 and 2.80 pounds per second per square foot.520::At 3.75 pounds pe At 3.75 pounds per second per square foot, the corresponding reduction was 4 to 12 inches of mercury. The trend was similar for both low-and high-volatility fuels and for two spark-energy levels.

IGNITION SYSTEMS - ENGINES, JET↗
NASA NTRS1951

Full-scale Investigation of Cooling Shroud and Ejector Nozzle for a Turbojet Engine : Afterburner Installation

A full-scale ejector cooling investigation was made on a turbojet engine - afterburner installation in the NACA Lewis altitude wind tunnel. Ejector performance was studied at primary exhaust-gas temperatures from 2700 degrees to 3400 degrees R (corresponding to ejector temperature ratios from 2.0 to 5.0), primary pressure ratios from 1.79 to 3.4, secondary air flows up to 29 percent of the primary gas flow, and for diameter ratios from 1.08 to 1.42 and spacing ratios from 0.04 to 1.16. In addition, variations were made in the primary exhaust-nozzle area. Ejectors with large diameter ratios permit the attainment of high gas flow ratios, but the jet-thrust losses become prohibitive as the spacing ratio is increased from 0 to 0.16. As the ejector diameter is reduced, the obtainable gas-flow ratio and the thrust loss are reduced. Previous results showing that data obtained at a temperature ratio of 1.0 could not be extrapolated to determine ejector performance at high temperature ratios by the application of the temperature ratio factor to the gas-flow ratios are substantiated by the present investigation.

AFTERBURNERS↗
NASA NTRS1951

Effects of Altitude on Turbojet Engine Performance

Component and over-all performance characteristics of several turbojet engines investigated in the altitude facilities of the NACA Lewis Laboratory during the last several years are summarized to indicate the effects of altitude on turbojet engine performance. Data presented show that failure of turbojet engine performance to generalize for all altitudes can be traced to reductions in compressor efficiency, corrected air flow, and combustion efficiency at altitude. In addition, it is shown that although engines of different design may have equal thrusts at sea level, the thrusts at altitude may vary widely because of differences in compressor performance characteristics from one engine to another.

COMPRESSORS - EFFICIENCY↗
NASA NTRS1954

Design of Combustor for Long-range Ram-jet Engine and Performance of Rectangular Analog

The report describes the design of a piloted combustor intended for a ram-jet engine of long flight range. The unit comprises a large annular basket of V-type cross-section, the inner surface of which is slotted and bent into small V-gutters. At the trailing edge of the basket, eight V-gutters are used to propagate the flame into the main stream. A rectangular analog of this combustor was tested at air-flow conditions corresponding to those that might be obtained during cruise. At these conditions, combustion efficiencies of as much as 90 percent were calculated for the combustor at the design equivalence ratio of 0.52. The performance of the unit was relatively insensitive to mounting and flow variables; the greatest effect on efficiency was that of the manner and location of the fuel injection. A full-scale version of this combustor has been designed for a 48-inch-diameter engine.

ENGINES, RAM-JET - COMBUSTION CHAMBERS↗