SEARCH · Engineering Papers

Results for “wind engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

All sources NASA NTRS DOE OSTI

NASA NTRS1992

Severe turbulence and maneuvering from airline flight records

Digital flight records from reported clear-air turbulence incidents are used to determine winds, to determine maneuver G loads, and to analyze control problems. Severe turbulence is found downwind of mountains and thunderstorms associated with vortices in atmospheric waves. It is also found in strong updrafts above thunderstorm buildups that are not detected by onboard weather radar. An important finding is that there are large maneuvering loads in over half of the reported clear-air turbulence incidents. Maneuvering loads are determined through an analysis of the short-term variations in elevator deflection and aircraft pitch angle. For altitude control in mountain waves the results indicate that small pitch angle changes with proper timing are sufficient to counter the vertical winds. For airspeed control in strong mountain waves, however, there is neither the available thrust nor the quickness in engine response necessary to counter the large and rapid variations in horizontal wind.

Wingrove, R. C.↗

DOE OSTI2016

A Comparison Study of Offshore Wind Support Structures with Monopiles and Jackets for U.S. Waters: Preprint

U.S. experience in offshore wind is limited, and high costs are expected unless innovations are introduced in one or multiple aspects of the project, from the installed technology to the balance of system (BOS). The substructure is the main single component responsible for the BOS capital expenditure (CapEx) and thus one that, if improved, could yield significant levelized cost of energy (LCOE) savings. For projects in U.S. waters, multimember, lattice structures (also known as jackets) can render required stiffness for transitional water depths at potentially lower costs than monopiles (MPs). In this study, we used a systems engineering approach to evaluate the LCOE of prototypical wind power plants at six locations along the eastern seaboard and the Gulf of Mexico for both types of support structures. Using a reference wind turbine and actual metocean conditions for the selected sites, we calculated loads for a parked and an operational situation, and we optimized the MP- and jacket-based support structures to minimize their overall mass. Using a suite of cost models, we then computed their associated LCOE. For all water depths, the MP-based configurations were heavier than their jacket counterparts, but the overall costs for the MPs were less than they were for jackets up to depths of slightly less than 30 m. When the associated manufacturing and installation costs were included, jackets resulted in lower LCOE for depths greater than 40 m. These results can be used by U.S. stakeholders to understand the potential for different technologies at different sites, but the methodology illustrated in this study can be further employed to analyze the effects of innovations and design choices throughout wind power plant systems.

17 WIND ENERGY↗

DOE OSTI2020

Comparison of electro-thermal performance of advanced cooling techniques for electric vehicle motors

Permanent magnet synchronous motors are commonly used in the powertrain of electric vehicles because of their high power and torque densities. Attempts to increase power and torque densities beyond the state-of-the-art often suffer from thermal limitations of the adopted winding-wire insulation class. In this paper, overall effectiveness of four different cooling technologies, namely conventional stator jacket cooling, embedded circular and rectangular cooling channels within stator core, and direct winding heat exchangers have been studied numerically. Here, by realizing temperature dependent magnetic and material properties, winding and core losses, a two-way coupling algorithm has been utilized to study the detailed electro-magnetic and thermal performance of BMW i3 motor with aforementioned cooling techniques. The numerical results illustrated that the direct winding heat exchangers approach provides better electro-thermal performance in comparison to the other cooling techniques analyzed. On the contrary, embedded rectangular and circular channel in stator core adversely affect the electro-magnetic performance and overall efficiency of the motor, despite their superior thermal performance compared to the jacket cooling

42 ENGINEERING↗

DOE OSTI2021

MIRACL Co‐Simulation platform for control and operation of distributed wind in microgrid

Abstract This paper presents a co‐simulation platform (CSP) developed as a part of the “Microgrids, Infrastructure Resilience and Advanced Controls Launchpad (MIRACL)” project, hereafter called MIRACL‐CSP, to allow simulation‐based testing, demonstration, and evaluations of distributed wind under various grid operating conditions. MIRACL‐CSP provides modular interactions among the power distribution system, distributed wind, and utility decision‐making framework. A hierarchical engine for large‐scale infrastructure co‐simulations (HELICS) is used as the core engine of MIRACL‐CSP to establish time and information coordination among the MIRACL‐CSP modules. In this study, MIRACL‐CSP performance is demonstrated using the IEEE 123‐node test distribution grid modelled in GridLAB‐D and the utility decision support application modelled in Python. The functionality of MIRACL‐CSP is demonstrated through various grid operational scenarios in a microgrid and networked microgrid environment. A co‐simulation study is described that demonstrated MIRACL‐CSP capabilities for the microgrid operational scenario in the IEEE 123‐node test system. MIRACL‐CSP is a generic platform that facilitates distributed wind research for different test systems, applications, and valuation of distributed wind.

17 WIND ENERGY↗

DOE OSTI2020

Grand Challenges in the Science of Wind Energy

The energy system of the future that depends on 80% or more renewable energy will put new demands on the wind systems that support it. There are significant areas of scientific uncertainly that need to be addressed to enable the innovation required for success. This presentation, based on a 2019 article in Science, lays out those areas of scientific challenges and proposes an integrated wind energy discipline that encompasses the needed research.

49 EE - Wind and Water Power Program - Wind (EE-4W↗

DOE OSTI2018

Three Confinement Systems—Spherical Tokamak, Standard Tokamak, and Stellarator: A Comparison of Key Component Cost Elements

Since the 1950s “next-step” fusion devices and power plant studies have been developed for a number of magnetic confinement systems but an open question remains: can a magnetic fusion device be simplified to the point where it will be cost competitive and operate with high availability? Concept designs based on the ARIES advanced tokamak, spherical tokamak (ST), and the quasi-axisymmetric (QAS) stellarator option have progressed in recent years through a series of Princeton Plasma Physics Laboratory (PPPL) studies with an underlying intent to improve the engineering feasibility of each, giving special attention to concepts that simplify the device configuration and improve maintenance features. For the ST option, design details centered on a 3-m Fusion Nuclear Science Facility that evolved to incorporate vertical maintenance, high temperature superconductor magnets, a small inboard duel coolant lead lithium blanket, and a liquid metal divertor. In collaboration with the Korean fusion demonstration reactor (K-DEMO) and CFETR concept study teams the tokamak design has evolved to increase plasma component access within a vertical maintenance approach using enlarged toroidal field coils incorporating a low- and high-field Nb 3 Sn winding pack that provide a peak field of 16 T. A recent PPPL stellarator study focused on simplifying the stellarator winding topology to improve access to in-vessel components; combining coil optimization with winding surfaces that incorporated geometry constraints specified by engineering. This paper centered on a 1000-MW power plant design with a tokamak like vertical maintenance scheme that allows access to remove large internal blanket sectors. Results of three confinement studies (PPPL developed ST, K-DEMO, and QAS stellarator) will be presented to highlight concepts that simplify each device configuration and improved their maintenance features. Furthermore, scaling each option to a common 1000-MW net electric power plant mission allows comparisons to be made of key cost elements such as the size of major core components, sizing of the reactor hall, or external facilities needed to handle and store activated in-vessel components.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2015

SubDyn User's Guide and Theory Manual

SubDyn is a time-domain structural-dynamics module for multimember fixed-bottom substructures created by the National Renewable Energy Laboratory (NREL) through U.S. Department of Energy Wind and Water Power Program support. The module has been coupled into the FAST aero-hydro-servo-elastic computer-aided engineering (CAE) tool. Substructure types supported by SubDyn include monopiles, tripods, jackets, and other lattice-type substructures common for offshore wind installations in shallow and transitional water depths. SubDyn can also be used to model lattice support structures for land-based wind turbines. This document is organized as follows. Section 1 details how to obtain the SubDyn and FAST software archives and run both the stand-alone SubDyn or SubDyn coupled to FAST. Section 2 describes the SubDyn input files. Section 3 discusses the output files generated by SubDyn; these include echo files, a summary file, and the results file. Section 4 provides modeling guidance when using SubDyn. The SubDyn theory is covered in Section 5. Section 6 outlines future work, and Section 7 contains a list of references. Example input files are shown in Appendixes A and B. A summary of available output channels are found in Appendix C. Instructions for compiling the stand-alone SubDyn program are detailed in Appendix D. Appendix E tracks the major changes we have made to SubDyn for each public release.

17 WIND ENERGY↗

NASA NTRSDate not supplied

Flight Test Evaluation of Automation-Induced Oscillations

Flight-test systems analysis techniques are applied to the case of aircraft automation-induced oscillations(AIO). Emerging technological advancements in flight control automation and artificial intelligence have created a need for evaluating the age-old aerial phenomenon of undesired aircraft oscillations. This paper is an overview on the study of AIO as interactions between human pilot, software engineer, and vehicle dynamics(e.g., latency) with the presence of winds aloft. Flight-test evaluation included a broad, non-comprehensive theory on cyclical and non-cyclical oscillations and a preliminary evaluation of the ecosystem from software engineer, airspace architect, and human test pilot.

David Zahn↗

NASA NTRS1976

Thermal design and analysis of a hydrogen-burning wind tunnel model of an airframe-integrated scramjet

An aerodynamic model of a hydrogen burning, airframe integrated scramjet engine has been designed, fabricated, and instrumented. This model is to be tested in an electric arc heated wind tunnel at an altitude of 35.39 km (116,094 ft.) but with an inlet Mach number of 6 simulating precompression on an aircraft undersurface. The scramjet model is constructed from oxygen free, high conductivity copper and is a heat sink design except for water cooling in some critical locations. The model is instrumented for pressure, surface temperature, heat transfer rate, and thrust measurements. Calculated flow properties, heat transfer rates, and surface temperature distributions along the various engine components are included for the conditions stated above. For some components, estimates of thermal strain are presented which indicate significant reductions in plastic strain by selective cooling of the model. These results show that the 100 thermal cycle life of the engine was met with minimum distortion while staying within the 2669 N (600 lbf) engine weight limitation and while cooling the engine only in critical locations.

Guy, R. W.↗

DOE OSTI2017

Gearbox Reliability Collaborative Gearbox 3 Planet Bearing Calibration

The Gearbox Reliability Collaborative gearbox was redesigned to improve its load-sharing characteristics and predicted fatigue life. The most important aspect of the redesign was to replace the cylindrical roller bearings with preloaded tapered roller bearings in the planetary section. Similar to previous work, the strain gages installed on the planet tapered roller bearings were calibrated in a load frame. This report describes the calibration tests and provides the factors necessary to convert the measured units from dynamometer testing to bearing loads, suitable for comparison to engineering models.

17 WIND ENERGY↗

NASA NTRS1978

Effects of inlet airframe integration on the inlet of an upper surface blowing four-engine STOL aircraft

Inlet and nacelle static pressures were measured on a 0.55-scale model of the Quiet Short-Haul Research Airplane (QSRA) in the Ames Research Center's 40- by 80-Foot Wind Tunnel. This model is powered by four JT-15D engines located above the wing with closely spaced adjacent inlets. A fifth JT-15D engine in the fuselage provides boundary-layer control air. Each inlet was instrumented with four to eight rows of axial pressure taps located between X/R approximately plus or minus 1. The tests simulated a broad range of aircraft operating conditions, including engine-out, with lift coefficients from 0.8 to 10.0. Results indicate that the inlets perform well under most operating conditions with little interaction between inlets when the aircraft is moving. Potential problem areas identified are high sideslip angle during approach and an interaction effect between adjacent inlets with high mass flows in static conditions.

Shovlin, M. D.↗

NASA NTRS1990

High speed turboprop aeroacoustic study (counterrotation). Volume 1: Model development

The isolated counterrotating high speed turboprop noise prediction program was compared with model data taken in the GE Aircraft Engines Cell 41 anechoic facility, the Boeing Transonic Wind Tunnel, and in NASA-Lewis' 8x6 and 9x15 wind tunnels. The predictions show good agreement with measured data under both low and high speed simulated flight conditions. The installation effect model developed for single rotation, high speed turboprops was extended to include counterotation. The additional effect of mounting a pylon upstream of the forward rotor was included in the flow field modeling. A nontraditional mechanism concerning the acoustic radiation from a propeller at angle of attach was investigated. Predictions made using this approach show results that are in much closer agreement with measurement over a range of operating conditions than those obtained via traditional fluctuating force methods. The isolated rotors and installation effects models were combines into a single prediction program, results of which were compared with data taken during the flight test of the B727/UDF engine demonstrator aircraft. Satisfactory comparisons between prediction and measured data for the demonstrator airplane, together with the identification of a nontraditional radiation mechanism for propellers at angle of attack are achieved.

Whitfield, C. E.↗

NASA NTRS1990

High speed turboprop aeroacoustic study (counterrotation). Volume 2: Computer programs

The isolated counterrotating high speed turboprop noise prediction program developed and funded by GE Aircraft Engines was compared with model data taken in the GE Aircraft Engines Cell 41 anechoic facility, the Boeing Transonic Wind Tunnel, and in the NASA-Lewis 8 x 6 and 9 x 15 wind tunnels. The predictions show good agreement with measured data under both low and high speed simulated flight conditions. The installation effect model developed for single rotation, high speed turboprops was extended to include counter rotation. The additional effect of mounting a pylon upstream of the forward rotor was included in the flow field modeling. A nontraditional mechanism concerning the acoustic radiation from a propeller at angle of attack was investigated. Predictions made using this approach show results that are in much closer agreement with measurement over a range of operating conditions than those obtained via traditional fluctuating force methods. The isolated rotors and installation effects models were combined into a single prediction program. The results were compared with data taken during the flight test of the B727/UDF (trademark) engine demonstrator aircraft.

Whitfield, C. E.↗

NASA NTRS1922

The choice of the speed of an airship

The favorable speed of an airship is chiefly determined by the condition of the consumption of the least amount of fuel per unit of traveled distance, although other conditions come into play. The resulting rules depend on the character of the wind and on the variability of the efficiency of the engine propeller units. This investigation resulted in the following rules. 1) Always keep the absolute course and steer at such an angle with reference to it as to neutralize the side wind. 2) In a strong contrary wind, take a speed one and one half times the velocity of the wind. 3) As a general rule, take the velocity of the wind and the velocity of the course component of the wind. Add them together if the wind has a contrary component, but subtract them from each other if the wind has a favorable component.

AIRSHIPS - SPEED↗

NASA NTRS2010

Drive Rig Mufflers for Model Scale Engine Acoustic Testing

Testing of air breathing propulsion systems in the 9x15 foot wind tunnel at NASA Glenn Research Center depends on compressed air turbines for power. The drive rig turbines exhaust directly to the wind tunnel test section, and have been found to produce significant unwanted noise that reduces the quality of the acoustic measurements of the model being tested. In order to mitigate this acoustic contamination, a muffler can be attached downstream of the drive rig turbine. The modern engine designs currently being tested produce much less noise than traditional engines, and consequently a lower noise floor is required of the facility. An acoustic test of a muffler designed to mitigate this extraneous noise is presented, and a noise reduction of 8 dB between 700 Hz and 20 kHz was documented, significantly improving the quality of acoustic measurements in the facility.

Stephens, David↗

DOE OSTI2021

OC6 Phase Ib: Floating Wind Component Experiment for Difference-Frequency Hydrodynamic Load Validation

A new validation campaign was conducted at the W2 Harold Alfond Ocean Engineering Laboratory at the University of Maine to investigate the hydrodynamic loading on floating offshore wind substructures, with a focus on the low-frequency contributions that tend to drive extreme and fatigue loading in semisubmersible designs. A component-level approach was taken to examine the hydrodynamic loads on individual parts of the semisubmersible in isolation and then in the presence of other members to assess the change in hydrodynamic loading. A variety of wave conditions were investigated, including bichromatic waves, to provide a direct assessment of difference-frequency wave loading. An assessment of the impact of wave uncertainty on the loading was performed, with the goal of enabling validation with this dataset of numerical models with different levels of fidelity. The dataset is openly available for public use and can be downloaded from the U.S. Department of Energy Data Archive and Portal.

17 WIND ENERGY↗

NASA NTRS1975

Reentry aerodynamics forces and moments on the engine nozzle of the 146-inch solid rocket booster model 473 tested in MSFC 14 by 14 inch trisonic wind tunnel (SA30F)

A test of a model of the Space Shuttle Solid Rocket Boosters (SRB's) was performed in a 14 x 14 inch Trisonic Wind Tunnel to determine the aerodynamic forces and moments imposed on the nozzle of the SRB during reentry. The model, with scale dimensions equal to 0.5479 of the actual SRB dimensions, was instrumented with a six-component force balance attached to the model nozzle so that only forces and moments acting on the nozzle were measured. A total of 137 runs (20 deg pitch polars) were performed during this test. The angle of attack ranged from 60 to 185 deg, the Reynolds number from 5.2 million to 7.6 million. The Mach numbers investigated were 1.96, 2.74, and 3.48. Five external protuberances were simulated. The effective roll angle simulated was 180 deg. The effects of three different heat shield configurations were investigated.

Johnson, J. D.↗

NASA NTRS1947

Wind-tunnel investigation of the effect of power and flaps on the static lateral characteristics of a single-engine low-wing airplane model

Tests were made in the Langley 7- by 10-foot tunnel to determine the lateral-stability characteristics with and without power of a model of a typical low-wing single-engine airplane with flaps neutral, with a full-span single slotted flap, and with a full-span double slotted flap. Power decreased the dihedral effect regardless of flap condition, and the double-slotted flap configuration showed the most marked decrease. The usual effect of power in increasing the directional stability was also shown. Deflection of the single slotted flap produced negative dihedral effect, but increased the directional stability. The effects of deflecting the double slotted flap were erratic and marked changes in both effective dihedral and directional stability occurred. The addition of the tail surfaces always contributed directional stability and generally produced positive dihedral effect.

Tamburello, Vito↗